Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interface stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Development of a high efficiency thin silicon solar cell

One hundred thin (120 microns to 260 microns) silicon-aluminum solar cells were fabricated and tested. Silicon slices were prepared, into which an aluminum alloy was evaporated over a range of temperatures and times. Antireflection coatings of tantalum oxide were applied to the cells. Reflectance of the silicon-aluminum interfaces was correlated to alloy temperature (graphs are shown). Optical measurements of the rear surface-internal reflectance of the cells were performed using a Beckman spectrophotometer. An improved gridline pattern was evaluated and stability tests (thermal cycling tests) were performed. Results show that: (1) a high-index, high-transmittance antireflection coating was obtained; (2) the improved metallization of the cells gave a 60 percent rear surface-internal reflectance, and the cells displayed excellent fill factors and blue response of the spectrum; (3) an improved gridline pattern (5 micron linewidths compared to 13 micron linewidths) resulted in a 1.3 percent improvement in short circuit currents; and (4) the stability tests showed no change in cell properties.

Lindmayer, J.↗
NASA NTRS1988

The crystallization of tough thermoplastic resins in the presence of carbon fibers

The presence of carbon fibers increased the crystallization rates of both PEEK and PPS thermoplastic polymers. The effect was most pronounced at higher crystallization temperatures. Isothermal crystallization rates were analyzed by applying classical phenomenological nucleation theory. Unusually high values of the so-called Avrami exponent were found for neat PEEK. Isothermal crystallization of PEEK and PPS polymers produced crystalline samples having a wide variety of melting temperatures. The melting as observed by differential scanning calorimetry occurred as dual endotherms which were called primary (higher temperature) and secondary melting peaks. Each primary peak accounted for most of the crystallinity present. The secondary peaks represented the melting of crystallites formed later than those attributable to the primary endotherms. The presence of carbon fibers increased the thermal stability of both PEEK and PPS crystallites as manifested by higher temperatures for the primary melting peaks. This may be attributable to increased crystallite size, greater crystallite perfection, and/or favorable modification of the crystallite interface. Over the range studied, crystallization temperature strongly influenced the positions of the secondary peaks but not the primary peaks.

Theil, Michael H.↗
NASA NTRS1992

Convection of tin in a Bridgman system. I - Flow characterization by effective diffusivity measurements

An electrochemical titration method was used to investigate the dynamic states in a cylindrical layer of convecting tin. The liquid tin was contained in a cell, with curved boundaries made of quartz and flat boundaries made of a solid state electrolyte - yttria-stabilized zirconia (YSZ). The electrolyte acted as a window through which a trace amount of oxygen could be pumped in or out by the application of a constant voltage. The concentration at the YSZ interface was monitored by operating the electrochemical cell in the galvanic mode. Experimentally determined effective diffusivities of oxygen were compared with the molecular diffusivity. Dynamic states in the convective flow were thus inferred. Temperature measurements were simultaneously made in order to identify the onset of oscillations from a steady convective regime. The experiments were conducted for two different aspect ratios for various imposed temperature gradients and two different orientations with respect to gravity. Transcritical states were identified and comparison to two-dimensional numerical models were made.

Sears, B.↗
NASA NTRS1990

Staggered solution procedures for multibody dynamics simulation

The numerical solution procedure for multibody dynamics (MBD) systems is termed a staggered MBD solution procedure that solves the generalized coordinates in a separate module from that for the constraint force. This requires a reformulation of the constraint conditions so that the constraint forces can also be integrated in time. A major advantage of such a partitioned solution procedure is that additional analysis capabilities such as active controller and design optimization modules can be easily interfaced without embedding them into a monolithic program. After introducing the basic equations of motion for MBD system in the second section, Section 3 briefly reviews some constraint handling techniques and introduces the staggered stabilized technique for the solution of the constraint forces as independent variables. The numerical direct time integration of the equations of motion is described in Section 4. As accurate damping treatment is important for the dynamics of space structures, we have employed the central difference method and the mid-point form of the trapezoidal rule since they engender no numerical damping. This is in contrast to the current practice in dynamic simulations of ground vehicles by employing a set of backward difference formulas. First, the equations of motion are partitioned according to the translational and the rotational coordinates. This sets the stage for an efficient treatment of the rotational motions via the singularity-free Euler parameters. The resulting partitioned equations of motion are then integrated via a two-stage explicit stabilized algorithm for updating both the translational coordinates and angular velocities. Once the angular velocities are obtained, the angular orientations are updated via the mid-point implicit formula employing the Euler parameters. When the two algorithms, namely, the two-stage explicit algorithm for the generalized coordinates and the implicit staggered procedure for the constraint Lagrange multipliers, are brought together in a staggered manner, they constitute a staggered explicit-implicit procedure which is summarized in Section 5. Section 6 presents some example problems and discussions concerning several salient features of the staggered MBD solution procedure are offered in Section 7.

Park, K. C.↗
NASA NTRS2000

Viscous and Thermal Effects on Hydrodynamic Instability in Liquid-Propellant Combustion

A pulsating form of hydrodynamic instability has recently been shown to arise during the deflagration of liquid propellants in those parameter regimes where the pressure-dependent burning rate is characterized by a negative pressure sensitivity. This type of instability can coexist with the classical cellular, or Landau, form of hydrodynamic instability, with the occurrence of either dependent on whether the pressure sensitivity is sufficiently large or small in magnitude. For the inviscid problem, it has been shown that when the burning rate is realistically allowed to depend on temperature as well as pressure, that sufficiently large values of the temperature sensitivity relative to the pressure sensitivity causes the pulsating form of hydrodynamic instability to become dominant. In that regime, steady, planar burning becomes intrinsically unstable to pulsating disturbances whose wavenumbers are sufficiently small. In the present work, this analysis is extended to the fully viscous case, where it is shown that although viscosity is stabilizing for intermediate and larger wavenumber perturbations, the intrinsic pulsating instability for small wavenumbers remains. Under these conditions, liquid-propellant combustion is predicted to be characterized by large unsteady cells along the liquid/gas interface.

Margolis, Stephen B.↗
DOE OSTI2023

Collection, release, and detection of analytes with polymer composite sampling materials

A unique fiber core sampler composition, related systems, and techniques for designing, making, and using the same are described. The sampler is used to interface with existing field instrumentation, such as Ion Mobility Spectrometer (IMS) equipment. Desired sampler characteristics include its: stiffness/flexibility; thermal mass and conductivity; specific heat; trace substance collection/release dependability, sensitivity and repeatability; thickness; reusability; durability; stability for thermal cleaning; and the like. In one form the sampler has a glass fiber core with a thickness less than 0.3 millimeter that is coated with a polymer including one or more of: polymeric organofluorine, polyimide, polyamide, PolyBenzlmidazole (PBI), PolyDiMethylSiloxane (PDMS), sulfonated tetrafluoroethylene (PFSA) and Poly(2,6-diphenyl-p-phenylene Oxide) (PPPO). Multiple polymer coatings with the same or different polymer types may be included, core/substrate surface functionalization utilized, and/or the core/substrate may be at partially filled with thermally conductive particles.

Addleman, Raymond S.↗
DOE OSTI2022

A fusion of the Bacteroides fragilis ferrous iron import proteins reveals a role for FeoA in stabilizing GTP-bound FeoB

Iron is an essential element for nearly all organisms, and under anoxic and/or reducing conditions, Fe 2+ is the dominant form of iron available to bacteria. The ferrous iron transport (Feo) system is the primary prokaryotic Fe 2+ import machinery, and two constituent proteins (FeoA and FeoB) are conserved across most bacterial species. However, how FeoA and FeoB function relative to one another remains enigmatic. In this work, we explored the distribution of feoAB operons encoding a fusion of FeoA tethered to the N-terminal, G-protein domain of FeoB via a connecting linker region. We hypothesized that this fusion poises FeoA to interact with FeoB to affect function. To test this hypothesis, we characterized the soluble NFeoAB fusion protein from Bacteroides fragilis, a commensal organism implicated in drug-resistant infections. Using X-ray crystallography, we determined the 1.50-Å resolution structure of BfFeoA, which adopts an SH3-like fold implicated in protein–protein interactions. Using a combination of structural modeling, small-angle X-ray scattering, and hydrogen–deuterium exchange mass spectrometry, we show that FeoA and NFeoB interact in a nucleotide-dependent manner, and we mapped the protein–protein interaction interface. Finally, using guanosine triphosphate (GTP) hydrolysis assays, we demonstrate that BfNFeoAB exhibits one of the slowest known rates of Feo-mediated GTP hydrolysis that is not potassium-stimulated. Importantly, truncation of FeoA from this fusion demonstrates that FeoA–NFeoB interactions function to stabilize the GTP-bound form of FeoB. Taken together, our work reveals a role for FeoA function in the fused FeoAB system and suggests a function for FeoA among prokaryotes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Continuous-flow reactor with superior production rate and stability for CO 2 reduction using semiconductor photocatalysts

Semiconductor photocatalyst approaches for solar CO 2 reduction are attractive due to their simplicity but have lagged in efficiency compared to less-integrated photoelectrochemical (PEC) approaches and to electrolysis reactors. We identify poor mass transport and catalyst deactivation as key constraints. To address them, we have developed a continuous-flow photocatalytic reactor system allowing us to control the triple-phase interface on the photocatalyst surface using the liquid and reactant gas flow rates. With the goal of selectively producing CO, the reactor is optimized by controlling the pressure and flow rates of the reactant gas and electrolyte in contact with both sides with the intermediately placed catalyst. In comparison to batch reactors with an immobile photocatalyst bed and gas phase CO 2 or CO 2 purged water, 10–24 times higher production rates are achieved for photocatalysts such as TiO 2 , ZnO, C 3 N 4 , and CdS by simply changing to the designed flow-type photoreactor without any catalyst modification. In addition, CO selectivity (93.2%) and long-term stability (>780 min) using the designed reactor are significantly enhanced compared to using the batch reactors (71.7%, <180 min for reduced 50% activity). Here, we propose that the enhanced mass transport on the photocatalyst surface accelerates the desorption of the initial photolysis product, CO, and prevents the poisoning effect from deactivating photocatalyst activity. This study has the potential to facilitate the utilization of semiconductor-based photocatalytic reactions for achieving superior performance wih gaseous reactants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Irradiation-enhanced Interactions at UO 2 /Al 2 O 3 /Al Interfaces

Combustion synthesis is used to prepare thin UO 2 films on aluminum alloy substrates. This simple preparation method involves electrospraying uranyl nitrate + acetylacetone + 2-methoxyethanol solution on the substrate, followed by a short annealing at 350 or 550 °C. The irradiation of films with a 40 Ar 2+ ion beam (energy of 1.7 MeV and fluences of 7.7 × 10 16 and 1.3 × 10 17 ions/cm 2 ) is conducted to investigate irradiation-induced restructuring processes. High-resolution transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) investigations show that the annealing temperature significantly influences the crystallinity and stability of materials during irradiation. A small amount of Mg in the alloy substrate diffuses into the amorphous Al 2 O 3 interfacial layer between the film and the substrate. Local thermal spikes from the incoming ions facilitate the irradiation-induced mixing of immiscible Al 2 O 3 and UO 2 for the materials prepared at 350 °C. This mass diffusion produces relatively large cavities at the interface. Selective diffusion of a more significant amount of Mg for the materials prepared at 550 °C suppresses the mixing of the Al 2 O 3 interlayer with the film but forms Mg y U 1–y O 2±x solid solutions during irradiation. Local thermal heating triggers the precipitation of a discontinuous crystalline MgO layer close to the film surface. As a result, the enhanced and selective diffusion of Mg into the film makes the materials prepared at 550 °C more robust and mechanically stable than those prepared at 350 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Frontiers of Ionic Liquids in Carbon Dioxide Separation and Valorization

Ionic liquids (ILs) have emerged as highly tunable sorbents and membranes for gas separation, especially in the purification of CO 2 -containing gas streams such as air, natural gas, biogas, and syngas. Their negligible volatility, high thermal stability, and chemical versatility position them as promising alternatives to conventional amine and alkaline metal derivative-based systems, effectively addressing key challenges such as volatility, stability, and high regeneration energy. Here, this Review explores IL-derived systems for CO 2 -related gas separation across dense, porous, and supported categories. At the dense liquid level, we discuss strategies for tailoring IL properties to optimize CO 2 sorption, focusing on the correlation between IL-CO 2 interaction strength, uptake capacity, and regeneration energy. Key advancements in carbon capture, including amino-functionalized (AILs) and superbase-derived ILs (SILs), are highlighted, along with strategies such as chemical structure engineering, multiple binding site integration, alternative driving force exploration, and stability enhancement. Then, the porous liquids (PLs) scale focuses on the emerging field integrating IL properties with permanent porosity engineering, spanning ultramicropores (<5 Å) to macropores (around 100 nm). These innovations improve gas uptake capacity, accelerate transport kinetics, introduce the gating effect, and enable the coexistence of active sites with antagonistic properties within a single IL medium. At the supported IL scale, the discussion shifts to IL- and ionic pair-modified sorbents and membranes, emphasizing the modulation of cations and anions, confinement effects from porous supports, and the IL–interface interaction to enhance CO 2 separation performance, particularly in diluted gas streams. Beyond separation, this Review highlights IL-based integrated processes for CO 2 capture and conversion into value-added chemicals via thermocatalytic, electrocatalytic, and photocatalytic pathways. At each scale, advanced computational and experimental tools for IL design are also discussed, providing insights into stability enhancement, sorption efficiency, and process integration. The Review concludes by addressing existing challenges and outlining future directions for IL-driven innovations in gas separation technologies.

Qiu, Liqi [Univ. of Tennessee, Knoxville, TN (Unit↗
DOE OSTI2022

Exploring implosion designs for increased compression on the National Ignition Facility using high density carbon ablators

It has long been recognized that high compression, and hence good confinement, is essential to achieving high yields in inertial confinement fusion implosions. In pursuit of multi-megajoule yields on the National Ignition Facility (NIF), a new campaign has begun aimed at testing the hypothesis that controlling hydrodynamic stability is key to achieving effective higher compression with the high density carbon ablators currently fielded on NIF. This campaign is built around a new implosion design, called SQ-n, that is derived from the uniquely stable Bigfoot design tested on NIF in 2016–2019. While very stable and with performance that was quite close to one-dimensional expectations, Bigfoot was a relatively high adiabat, and consequently lower compression design. The goal of SQ-n is then to evolve Bigfoot toward a higher compression design but without compromising its unique stability characteristics. Specifically, SQ-n adopts a ramped foot pulse shape to minimize early time Richtmyer–Meshkov instability growth and uses an ablator dopant distribution extending all of the way to the fuel–ablator interface that simulations suggest further reduces perturbation growth. In conclusion, this paper describes the design philosophy pursued with SQ-n, the results of instability modeling of the candidate design, and the experimental campaign planned to test these ideas in the near future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1976

STOLAND

The STOLAND system includes air data, navigation, guidance, flight director (including a throttle flight director on the Augmentor Wing), 3-axis autopilot and autothrottle functions. The 3-axis autopilot and autothrottle control through parallel electric servos on both aircraft and on the augmentor wing, the system also interfaces with three electrohydraulic series actuators which drive the roll control surfaces, elevator and rudder. The system incorporates automatic configuration control of the flaps and nozzles on the augmentor wing and of the flaps on the Twin Otter. Interfaces are also provided to control the wing flap chokes on the Augmentor Wing and the spoilers on the Twin Otter. The STOLAND system has all the capabilities of a conventional integrated avionics system. Aircraft stabilization is provided in pitch, roll and yaw including control wheel steering in pitch and roll. The basic modes include altitude hold and select, indicated airspeed hold and select, flight path angle hold and select, and heading hold and select. The system can couple to TACAN and VOR/DME navaids for conventional radial flying.

Grgurich, J.↗
NASA NTRS1982

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project. ACT/Control/Guidance System study, volume 1

The active control technology (ACT) control/guidance system task of the integrated application of active controls (IAAC) technology project within the NASA energy efficient transport program was documented. The air traffic environment of navigation and air traffic control systems and procedures were extrapolated. An approach to listing flight functions which will be performed by systems and crew of an ACT configured airplane of the 1990s, and a determination of function criticalities to safety of flight, are the basis of candidate integrated ACT/Control/Guidance System architecture. The system mechanizes five active control functions: pitch augmented stability, angle of attack limiting, lateral/directional augmented stability, gust load alleviation, and maneuver load control. The scope and requirements of a program for simulating the integrated ACT avionics and flight deck system, with pilot in the loop, are defined, system and crew interface elements are simulated, and mechanization is recommended. Relationships between system design and crew roles and procedures are evaluated.

Source record↗
NASA NTRS1985

Modeling Directional Solidification

The objective of the research is to develop tools of use in explaining the results of directional solidification experiments in space. These tools consist of mathematical and experimental models. Experiments are also being flown at low-g to validate the ground-based results. Many metals and semiconductors directionally solidified in space had a diameter less than that of the containing ampoule. In fact this occurred whenever the ampoule contained a gas space. This phenomenon has been attributed in a vague way to lack of wetting of the ampoule wall by the melt. The actual liquid behavior by use of low temperature analogs is being observed aboard the KC-135. In the first flight, water was placed in plastic ampoules (not wet) with ceramic end plugs which were wet by the water to simulate a solid-liquid interface. Unfortunately during storage prior to the flight the water began to wet the ampoule wall. Discrete bubbles formed down the axis of the ampoules. New ampoule materials are being used now, with testing for stability prior to the next flight. A theoretical model has also been developed for this phenomenon.

Wilcox, W. R.↗
NASA NTRS1996

Mullite fiber reinforced reaction bonded Si3N4 composites

Fracture toughnesses of brittle ceramic materials have been improved by introducing reinforcements and carefully tailored interface layers. Silicon carbide and Si3N4 have been emphasized as matrices of structural composites intended for high temperature service because they combine excellent mechanical, chemical, thermal and physical properties. Both matrices have been successfully toughened with SiC fibers, whiskers and particles for ceramic matrix composite (CMC) parts made by sintering, hot pressing or reaction forming processes. These SiC reinforced CMCs have exhibited significantly improved toughnesses at low and intermediate temperature levels, as well as retention of properties at high temperatures for selected exposures; however, they are vulnerable to attack from elevated temperature dry and wet oxidizing atmospheres after the matrix has cracked. Property degradation results from oxidation of interface layers and/or reinforcements. The problem is particularly acute for small diameter (-20 tim) polymer derived SiC fibers used for weavable toes. This research explored opportunities for reinforcing Si3N4 matrices with fibers having improved environmental stability; the findings should also be applicable to SiC matrix CMCs.

Saleh, T.↗
NASA NTRS1996

(abstract) Precision Time and Frequency Transfer Utilizing SONET OC-3

An innovative method of distributing precise time and reference frequency to users located several kilometers from a frequency standard and master clock has been developed by the Timing Solutions Corporation of Boulder, CO. The Optical Two-Way Time Transfer System (OTWTTS) utilizes a commercial SONET OC-3 facility interface to physically connect a master unit to multiple slave units at remote locations. Optical fiber is a viable alternative to standard copper cable and microwave transmission. This paper discusses measurements of frequency and timing stability over the OTWTTS.

optical fiber precision time standards frequency r↗
NASA NTRS2014

Assessing Fan Flutter Stability in Presence of Inlet Distortion Using One-Way and Two-Way Coupled Methods

Concerns regarding noise, propulsive efficiency, and fuel burn are inspiring aircraft designs wherein the propulsive turbomachines are partially (or fully) embedded within the airframe; such designs present serious concerns with regard to aerodynamic and aeromechanic performance of the compression system in response to inlet distortion. Previously, a preliminary design of a forward-swept high-speed fan exhibited flutter concerns in clean-inlet flows, and the present author then studied this fan further in the presence of off-design distorted in-flows. Continuing this research, a three-dimensional, unsteady, Navier-Stokes computational fluid dynamics code is again applied to analyze and corroborate fan performance with clean inlet flow and now with a simplified, sinusoidal distortion of total pressure at the aerodynamic interface plane. This code, already validated in its application to assess aerodynamic damping of vibrating blades at various flow conditions using a one-way coupled energy-exchange approach, is modified to include a two-way coupled timemarching aeroelastic simulation capability. The two coupling methods are compared in their evaluation of flutter stability in the presence of distorted in-flows.

fluid-structure interaction↗
DOE OSTI2023

Improving Frequency Stability and Minimizing Load Shedding Events by Adopting Grid-Scale Energy Storage with Grid Forming Inverters

The upward adoption trend of renewable generation not only means cleaner energy integrated into modern power grids, but also that most new generation sources are based on front-end inverter bridges, used as interfaces to most wind generation and all the solar PV. It is well known that due to their power electronics-based construction rather than rotational shafts, these sources do not provide inertia inherently, nor substantial amounts of short-circuit currents. However, stable energy such as what can be stored in energy storage systems, although interfaced via inverters, can be controlled to respond to system disturbances in a manner that emulates inertial behavior. This paper focuses on the application of such energy storage systems to augment inertia in the island of Puerto Rico. To do so, a user defined inverter model that contains grid forming capabilities and fast frequency response is modeled and integrated into the real transmission system in power flow and dynamics software. Energy storage is then connected to two selected areas so that it not only provides frequency regulation to avoid widespread load shedding events, but also other tangible benefits. The simulated cases suggest that even relatively small energy storage systems can avert load shedding events if adequately placed in the transmission network.

Grid-forming inverters, IBR, Inertia↗