Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hydrodynamics experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Optimization-based calibration of hydrodynamic drag coefficients for a semisubmersible platform using experimental data of an irregular sea state

For the simulation of the coupled dynamic response of floating offshore wind turbines, it is crucial to calibrate the hydrodynamic damping with experimental data. The aim of this work is to find a set of hydrodynamic drag coefficients for the semisubmersible platform of the Offshore Code Comparison Collaboration, Continuation, with Correlation and unCertainity (OC6) project which provides suitable results for an irregular sea state. Due to the complex interaction of several degrees of freedom (DOF), it is common to calibrate drag coefficients with the time series of decay tests. However, applying these drag coefficients for the simulation of an irregular sea state results in misprediction of the motions. By using numerical optimization, it is possible to calibrate multiple drag coefficients simultaneously and effectively, while also considering several DOF. This work considers time series of structural displacements from wave tank tests of the OC6 project and from simulations of the same load cases in OpenFAST. Results are transferred into the frequency domain and the deviation between power spectral densities of surge, pitch and heave from experiment and numerical simulation is used as an objective function to obtain the best fitting drag coefficients. This novel numerical optimization approach enables finding one set of drag coefficients for different load cases, which is a major improvement compared to decay-test-tuned drag coefficients.

42 ENGINEERING↗

Mesoscale Simulation of Proton Transport in Proton Exchange Membranes

Previous efforts to model proton transport through fuel cell membranes have largely focused on disparate length scales: molecular dynamics at the atomistic level and fuel cell stack engineering approaches at the macroscale. A new multiscale approach to bridge these extremes is proposed in this work which combines concepts from coarse-grained (CG) modeling with smoothed particle hydrodynamics (SPH) to capture the qualitative morphology and transport behavior of a proton exchange membrane at the length scale of tens of nanometers. This method allows for connection to atomistic simulations via the inclusion of transport coefficients from molecular dynamics and coarse-grained forces derived for the polymer backbone, side chain, proton, and water interactions. Information pertaining to macroscopic conductivity is obtained by volume averaging based on the flux and chemical potential fields within the membrane. Proton transport is effectively coarse-grained via introduction of a composition variable associated with each interacting site which carries the field information. By combining this technique with local electrostatics and coordinate dependent diffusion constants, the effects of double layer formation within the water pores and the influence of proximity to sulfonate groups on transport is recovered. The combined CG-SPH method is validated and subsequently applied to an equilibrated hydrated Nafion structure with a box length of 40 nm. The resulting conductivities calculated for the material agree very well with trends from experiment and provide insight into the complex interplay of morphology, proton distribution, and diffusion coefficients at a length scale that can be expanded beyond feasible atomistic molecular dynamics simulations to capture the effects of mesoscopic morphology on proton conduction.

Jorn, Ryan↗

Entropy generation from hydrodynamic mixing in inertial confinement fusion indirect-drive targets

The increase in entropy from the physical mixing of two adjacent materials in inertial confinement fusion (ICF) implosions and gas-filled hohlraums is analytically assessed. An idealized model of entropy generation from the mixing of identical ideal-gas particles across a material interface in the presence of pressure and temperature gradients is applied. Physically, mix-driven entropy generation refers to the work done by the gases in expanding into a larger common volume from atomic mixing under the condition of no internal energy change, or work needed to restore the initial unmixed state. Furthermore, the effect of a mix-generated entropy increase is analytically shown to lead to less compression of the composite ICF fluid under adiabatic conditions. The amount of entropy generation is estimated to be ~10 J for a Rayleigh–Taylor-induced micrometer-scale annular mixing layer between the solid deuterium–tritium fuel and (undoped) high-density carbon pusher of an imploding capsule at the National Ignition Facility (NIF). This level of entropy generation is consistent with lower-than-expected fuel compressions measured on the NIF [Hurricane et al., Phys. Plasmas 26, 052704 (2019)]. The degree of entropy increase from mixing of high-Z hohlraum wall material and low-Z, moderate- to high-density gas fills is estimated to lead to ~100 kJ of heat generation for NIF-scale experiments [Moody et al., Phys. Plasmas 21, 056317 (2014)]. This value represents a significant fraction of the inferred missing x-ray drive energy based on observed delays in capsule implosion times compared with mainline simulations [Jones et al., Phys. Plasmas 19, 056315 (2012)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Power capture and power take-off load of a self-balanced dual-flap oscillating surge wave energy converter

Wave energy converters are an important part of future renewable energy infrastructure. Predicting their power matrix, capture width ratio, and power take-off loads at a targeted site is required for performance assessment before deployment. Because their testing is very expensive, numerical modeling and simulations play a significant role in those assessments. Linear potential flow theory has limited accuracy under large amplitude wave forcing. More accurate predictions can be obtained by using higher-fidelity models, which are computationally expensive. We present a framework for multi-fidelity numerical simulations to determine the hydrodynamic response, wave capture capability, and power take-off load of a full-scale dual-flap oscillating surge wave energy converter. This design exploits out-of-phase motion by setting the distance between the flaps to half the wavelength of the most occurring wave. The simulations are validated using a 1:10 model experiments in a wave tank. Based on these validations, it was determined that Euler simulations provide an acceptable prediction with 90% reduction in computational time with only 11% error. Utilizing Euler simulations at full-scale, the results demonstrate that the annual electrical energy output is 1.79 GWh under regular wave conditions. Here, one significant improvement over single-flap designs is the capture width ratio which exceeds unity.

16 TIDAL AND WAVE POWER↗

Anomalous wave structure in magnetized materials described by non-convex equations of state

We analyze the anomalous wave structure appearing in flow dynamics under the influence of magnetic field in materials described by non-ideal equations of state. We consider the system of magnetohydrodynamics equations closed by a general equation of state (EOS) and propose a complete spectral decomposition of the fluxes that allows us to derive an expression of the nonlinearity factor as the mathematical tool to determine the nature of the wave phenomena. We prove that the possible formation of non-classical wave structure is determined by both the thermodynamic properties of the material and the magnetic field as well as its possible rotation. We demonstrate that phase transitions induced by material properties do not necessarily imply the loss of genuine nonlinearity of the wavefields as is the case in classical hydrodynamics. The analytical expression of the nonlinearity factor allows us to determine the specific amount of magnetic field necessary to prevent formation of complex structure induced by phase transition in the material. We illustrate our analytical approach by considering two non-convex EOS that exhibit phase transitions and anomalous behavior in the evolution. We present numerical experiments validating the analysis performed through a set of one-dimensional Riemann problems. In the examples we show how to determine the appropriate amount of magnetic field in the initial conditions of the Riemann problem to transform a thermodynamic composite wave into a simple nonlinear wave.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental validation of thermodynamic mixture rules at extreme pressures and densities

Accurate modeling of a mixed material Equation of State (EOS) at high pressures (~1 to 100 Mbar) is critical for simulating inertial confinement fusion and high energy density systems. Here, this paper presents a comparison of two mixing rule models to the experiment to assess their applicability in this regime. The shock velocities of polystyrene, aluminum, and nickel aluminide (NiAl) were measured at a shock pressure of ~3 TPa (~30 Mbar) on the Omega EP laser facility (Laboratory for Laser Energetics, University of Rochester, New York). The resultant shock velocities were compared to those derived from the RAGE (Eulerian) hydrodynamics code to validate various mixing rules used to construct an EOS for NiAl. The simulated shock transit time through the sample (Al or NiAl) matched the measurements to within the ±45ps measurement uncertainty. The law of partial volume (Amagat) and the law of partial pressure (Dalton) mixture rules provided equally good matches to the NiAl shock data. Other studies showed that the Amagat mixing rule is superior, and we recommend it since our results also show a satisfactory match. In conclusion, the comparable quality of the simulation to data for the Al and NiAl samples implies that a mixture rule can supply an EOS for plasma mixtures with adequate fidelity for simulations where mixing takes place, such as advective mix in an Eulerian code or when two materials are mixed together via diffusion, turbulence, or other physical processes.

36 MATERIALS SCIENCE↗

Effects of thermal conductivity of liquid layer in NIF wetted foam experiments

Numerical simulation of inertial confinement fusion (ICF) capsule implosion experiments needs many plasma parameters corresponding to different materials and their mixtures for a wide range of densities and temperatures. Thermal conduction plays a crucial role in coupling energy to the capsule, is one of the primary mechanisms of energy loss during implosion, has a significant effect on hot-spot formation, and impacts the growth of hydrodynamic instabilities. The determination of accurate thermal conductivity of ICF relevant materials is thus important for understanding capsule performance. Analytic models such as Spitzer or Lee-More models have been extensively used in simulations due to the limited availability of experimental data. First principles calculations have shown that these analytic models tend to underestimate electron thermal conductivity in the warm dense plasma regime for ICF related materials. Here, we numerically investigate the effects of different models for the electron heat conductivity coefficients, including both analytic and Quantum Molecular Dynamics (QMD)-based models, for mixed materials in ICF. We also investigate the impact of how conductivities are calculated in mixed cells from constituent material conductivities. We apply this to the modeling of recent wetted foam capsule implosions on the National Ignition Facility, in which a foam layer on the inside of the capsule is wetted with deuterium-tritium (DT) liquid. We have found that electron heat conductivity affects the initial hot-spot formation and its evolution. Strikingly, we observe that capsule performance is more sensitive to the method used to mix material conductivities in mixed cells than how individual material conductivity coefficients are calculated. Furthermore, we have found that using the first principles QMD-based conductivity model along with an appropriate model for mixed-cell conductivities yields better agreement with experimental results compared to the established modeling strategies. We also investigate the impact of mixed material conductivity modeling on the process of ablator material mixing with DT ice in a plastic ice-layer capsule. In our simulations, the heat conductivity model affects the calculated mix widths at the fuel-ablator interface, particularly near the tent scar. Additional mixing between the DT fuel and the ablator in turn increases the implosion adiabat, which results in a lower hot-spot pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Vortex-sheet modeling of hydrodynamic instabilities produced by an oblique shock interacting with a perturbed interface in the HED regime

In this work, we consider hydrodynamic instabilities produced by the interaction of an oblique shock with a perturbed material interface under high-energy-density (HED) conditions. During this interaction, a baroclinic torque is generated along the interface due to the misalignment between the density and pressure gradients, thus leading to perturbation growth. Our objective is to understand the competition between the impulsive acceleration due to the normal component of the shock velocity, which drives the Richtmyer–Meshkov instability, and the shear flow across the interface due to the tangential component of the shock velocity, which drives the Kelvin–Helmholtz instability, as well as its relation to perturbation growth. Since the vorticity resulting from the shock-interface interaction is confined to the interface, we describe the perturbation growth using a two-dimensional vortex-sheet model. We demonstrate the ability of the vortex-sheet model to reproduce roll-up dynamics for non-zero Atwood numbers by comparing to past laser-driven HED experiments. We determine the dependence of the interface dynamics on the tilt angle and propose a time scaling for the perturbation growth at early time. Eventually, this scaling will serve as a platform for the design of future experiments. This study is the first attempt to incorporate into a vortex-sheet model the time-dependent interface decompression and the deceleration (as well as the corresponding Rayleigh–Taylor instability) arising from laser turn-off.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scaling and dimensional analysis of acoustic streaming jets

This paper focuses on acoustic streaming free jets. This is to say that progressive acoustic waves are used to generate a steady flow far from any wall. The derivation of the governing equations under the form of a nonlinear hydrodynamics problem coupled with an acoustic propagation problem is made on the basis of a time scale discrimination approach. This approach is preferred to the usually invoked amplitude perturbations expansion since it is consistent with experimental observations of acoustic streaming flows featuring hydrodynamic nonlinearities and turbulence. Experimental results obtained with a plane transducer in water are also presented together with a review of the former experimental investigations using similar configurations. A comparison of the shape of the acoustic field with the shape of the velocity field shows that diffraction is a key ingredient in the problem though it is rarely accounted for in the literature. A scaling analysis is made and leads to two scaling laws for the typical velocity level in acoustic streaming free jets; these are both observed in our setup and in former studies by other teams. We also perform a dimensional analysis of this problem: a set of seven dimensionless groups is required to describe a typical acoustic experiment. We find that a full similarity is usually not possible between two acoustic streaming experiments featuring different fluids. We then choose to relax the similarity with respect to sound attenuation and to focus on the case of a scaled water experiment representing an acoustic streaming application in liquid metals, in particular, in liquid silicon and in liquid sodium. We show that small acoustic powers can yield relatively high Reynolds numbers and velocity levels; this could be a virtue for heat and mass transfer applications, but a drawback for ultrasonic velocimetry.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Turbulence in strongly coupled dusty plasmas using generalized hydrodynamic description

The properties of decaying turbulence have been studied with the help of a Generalized Hydrodynamic (GHD) fluid model in the context of strongly coupled dusty plasma medium in two dimensions. The GHD model treats the strongly coupled dusty plasma system as a visco-elastic medium. The incompressible limit of the GHD model is considered here. The studies carried out here are, however, applicable to a wider class of visco-elastic systems, and are not merely confined to the dusty plasma medium. Our simulations studies show that an initial spectrum that is confined in a limited domain of wave numbers becomes broad, even when the Reynold's number is much less than the critical value required for the onset of turbulence in Newtonian fluids. This is a signature of elastic turbulence, where Weissenberg's number also plays an important role on the onset of turbulence. This feature has been observed in several experiments. It is also shown that the existence of memory relaxation time parameter and the transverse shear wave inhibit the normal process (for 2-D systems) of inverse spectral cascade in this case. A detailed simulation study has been carried out for the understanding of this inhibition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Campaign 2 Level 2 Milestone Review 2009: Milestone # 3131 Grain Scale Simulation of Pore Collapse

The milestone reviewed on Sept. 16, 2009 was 'High-fidelity simulation of shock initiation of high explosives at the grain scale using coupled hydrodynamics, thermal transport and chemistry'. It is the opinion of the committee that the team has satisfied the milestone. A detailed description of how the goals were met is provided. The milestone leveraged capabilities from ASC Physics and Engineering Materials program combined with experimental input from Campaign 2. A combined experimental-multiscale simulation approach was used to create and validate the various TATB model components. At the lowest length scale, quantum chemical calculations were used to determine equations of state, thermal transport properties and reaction rates for TATB as it is decomposing. High-pressure experiments conducted in diamond anvil cells, gas guns and the Z machine were used to validate the EOS, thermal conductivity, specific heat and predictions of water formation. The predicted reaction networks and chemical kinetic equations were implemented in Cheetah and validated against the lower length scale data. Cheetah was then used within the ASC code ALE3D for high-resolution, thermo-mechanically coupled simulations of pore collapse at the micron size scale to predict conditions for detonation initiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Summaries of FY 2018 LANL experimental campaigns at the OMEGA and OMEGA-EP Laser Facilities

In FY 2018, Los Alamos National Laboratory carried out 21 shot days on the OMEGA and OMEGA-EP laser facilities in the areas of High Energy Density (HED) Science and Inertial Confinement Fusion (ICF). Our focus areas were on radiation flow, hydrodynamic turbulent mix and burn, and coupled Kelvin-Helmholtz (KH)/Richtmyer-Meshkov (RM) instability growth including in convergent geometry. We also had several focused shot days on transport properties in the kinetic regime. We continue to develop advanced diagnostics such as Neutron Imaging , and performed tests of a new imaging concept to be installed on NIF. We executed experiments in support of our double-shell campaign, and we began initial experiments using the new Revolver platform. Below is a summary of our campaigns, their motivation, and main results from this year.

47 OTHER INSTRUMENTATION↗

Prediction of Ablation Rates from Solid Surfaces Exposed to High Temperature Gas Flow

A mathematical model and a solution algorithm is developed to study the physics of high temperature heat transfer and material ablation and identify the problems associated with the flow of hydrogen gas at very high temperatures and velocities through pipes and various components of Nuclear Thermal Rocket (NTR) motors. Ablation and melting can be experienced when the inner solid surface of the cooling channels and the diverging-converging nozzle of a Nuclear Thermal Rocket (NTR) motor is exposed to hydrogen gas flow at temperatures around 2500 degrees Kelvin and pressures around 3.4 MPa. In the experiments conducted on typical NTR motors developed in 1960s, degradation of the cooling channel material (cracking in the nuclear fuel element cladding) and in some instances melting of the core was observed. This paper presents the results of a preliminary study based on two types of physics based mathematical models that were developed to simulate the thermal-hydrodynamic conditions that lead to ablation of the solid surface of a stainless steel pipe exposed to high temperature hydrogen gas near sonic velocities. One of the proposed models is one-dimensional and assumes the gas flow to be unsteady, compressible and viscous. An in-house computer code was developed to solve the conservations equations of this model using a second-order accurate finite-difference technique. The second model assumes the flow to be three-dimensional, unsteady, compressible and viscous. A commercial CFD code (Fluent) was used to solve the later model equations. Both models assume the thermodynamic and transport properties of the hydrogen gas to be temperature dependent. In the solution algorithm developed for this study, the unsteady temperature of the pipe is determined from the heat equation for the solid. The solid-gas interface temperature is determined from an energy balance at the interface which includes heat transfer from or to the interface by conduction, convection, radiation, and ablation. Two different ablation models are proposed to determine the heat loss from the solid surface due to the ablation of the solid material. Both of them are physics based. Various numerical simulations were carried out using both models to predict the temperature distribution in the solid and in the gas flow, and then predict the ablation rates at a typical NTR motor hydrogen gas temperature and pressure. Solid mass loss rate per foot of a pipe was also calculated from these predictions. The results are presented for fully developed turbulent flow conditions in a sample SS pipe with a 6 inch diameter.

Akyuzlu, Kazim M.↗

IUTAM symposium on hydrodynamic diffusion of suspended particles

Hydrodynamic diffusion refers to the fluctuating motion of nonBrownian particles (or droplets or bubbles) which occurs in a dispersion due to multiparticle interactions. For example, in a concentrated sheared suspension, particles do not move along streamlines but instead exhibit fluctuating motions as they tumble around each other. This leads to a net migration of particles down gradients in particle concentration and in shear rate, due to the higher frequency of encounters of a test particle with other particles on the side of the test particle which has higher concentration or shear rate. As another example, suspended particles subject to sedimentation, centrifugation, or fluidization, do not generally move relative to the fluid with a constant velocity, but instead experience diffusion-like fluctuations in velocity due to interactions with neighboring particles and the resulting variation in the microstructure or configuration of the suspended particles. In flowing granular materials, the particles interact through direct collisions or contacts (rather than through the surrounding fluid); these collisions also cause the particles to undergo fluctuating motions characteristic of diffusion processes. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Diffusion↗

Extended X-Ray Absorption Fine Structure Measurements of Quasi-Isentropically Compressed Vanadium Targets on the OMEGA Laser

The use of in situ extended x-ray absorption fine structure (EXAFS) for characterizing nanosecond laser-shocked vanadium, titanium, and iron has recently been demonstrated. These measurements are extended to laser-driven, quasi-isentropic compression experiments (ICE). The radiation source (backlighter) for EXAFS in all of these experiments is obtained by imploding a spherical target on the OMEGA laser [T. R. Boehly et al., Rev. Sci. Instrum. 66, 508 (1995)]. Isentropic compression (where the entropy is kept constant) enables to reach high compressions at relatively low temperatures. The absorption spectra are used to determine the temperature and compression in a vanadium sample quasi-isentropically compressed to pressures of up to ~0.75 Mbar. The ability to measure the temperature and compression directly is unique to EXAFS. The drive pressure is calibrated by substituting aluminum for the vanadium and interferometrically measuring the velocity of the back target surface by the velocity interferometer system for any reflector (VISAR). The experimental results obtained by EXAFS and VISAR agree with each other and with the simulations of a hydrodynamic code. The role of a shield to protect the sample from impact heating is studied. It is shown that the shield produces an initial weak shock that is followed by a quasi-isentropic compression at a relatively low temperature. The role of radiation heating from the imploding target as well as from the laser-absorption region is studied. The results show that in laser-driven ICE, as compared with laser-driven shocks, comparable compressions can be achieved at lower temperatures. The EXAFS results show important details not seen in the VISAR results.

Yaakobi, B↗

MIX and Instability Growth from Oblique Shock

We have studied the formation and evolution of shock-induced mix resulting from interface features in a divergent cylindrical geometry. In this research a cylindrical core of high-explosive was detonated to create an oblique shock wave and accelerate the interface. The interfaces studied were between the high-explosive/aluminum, aluminum/plastic, and finally plastic/air. Pre-emplaced surface features added to the aluminum were used to modify this interface. Time sequence radiographic imaging quantified the resulting instability formation from the growth phase to over 60 {micro}s post-detonation. Thus allowing the study of the onset of mix and evolution to turbulence. The plastic used here was porous polyethylene. Radiographic image data are compared with numerical simulations of the experiments.

36 MATERIALS SCIENCE↗

The Effects of Material-Filled Voids on Detonation Wave Shape in Rubberized RDX Explosives

The sensitivity of explosives is affected by inhomogeneities within the material. This is evident in the increased shock sensitivity of explosives with slightly lower densities resulting from an increased number of hotspots. The influence of hotspots on explosive initiation has been well studied; however, few studies have been conducted on the effect of intermediate-sized voids (0.1–10 mm) on a propagating detonation wave. Cylindrical voids filled with air have been studied for diameters ranging from 0.3 mm to 0.8 mm for both 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX) and 1,3,5-trinitro-1,3,5-triazinane (RDX)-based rubberized explosives. Continuing the investigation into single cylindrical voids, this study examined the effects of 0.5 mm diameter voids filled with different inert cylindrical metals on the detonation wave shape for an RDX-based rubberized explosive. The metals selected for experiments were 1066 aluminum, brass, copper, and tungsten. The propagation of the detonation wave was captured using a digital streak camera. Experimental results showed that the extent of detonation wave shaping was closely tied to the density differential between the bulk explosive and metal insert. Forty-four different filler materials, including non-metals, were simulated using a hydrodynamic code to further analyze material inclusion effects. The main factors hypothesized to be of interest were bulk sound speed, shock impedance, and filler material density. We found that the local detonation delay could be correlated fairly well to a ratio of bulk sound speed and density. Understanding the influence of material inclusions on detonation performance and wave shape allows for tailoring of detonations.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗