Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

On the thermal oxidation of nuclear graphite relevant to high-temperature gas cooled reactors

Thermal oxidation of nuclear graphite components is highly undesirable because it can cause structural and property degradation that negatively affect a reactor's intended operation. In this work, the body of knowledge of nuclear graphite oxidation is highlighted, including when O 2 , H 2 O, and/or CO 2 are the oxidant. Oxidation conditions relevant to high-temperature gas-cooled reactors (i.e., when oxidation could occur either as an acute or chronic phenomenon) are emphasized. Here, the objective is to summarize graphite oxidation data in a practical and accessible way to inform future research and regulatory requirements. Although each grade of nuclear graphite is different, the oxidation mechanism has underlying commonalities. Although oxidation behavior is grade dependent, the general temperature dependence is well described by a sequence of elementary steps which become rate limiting. Because the regime transition temperature depends on sample microstructure, size, and oxidant supply rate, extrapolating results beyond the experimental range should be done cautiously. Gravimetric oxidation rate measurements generally replicate well. However, caution must be exercised when rates are estimated by other methods or for samples that deviate significantly in size. Air oxidation data for IG-110, NBG-18, and PCEA graphite is critically reviewed to emphasize this point. Despite the amount of experimental data, gaps remain. Sample size and shape effects are not fully explained. Data on the oxidant penetration depth are insufficient. Analytical assessments demonstrate that lower temperature oxidation does not necessarily imply that oxidation is uniform throughout the bulk. Oxidation occurs faster at higher temperature but is more localized to the exposed surface. Paradoxically, at equal mass loss percentage, low temperature oxidation leads to greater property degradation than at high temperature. The isolated effect of oxidation is important; however, a gap remains in the systematic understanding of any potential effect of neutron irradiation on graphite structure and reactivity.

36 MATERIALS SCIENCE↗

Carbon flux estimates are sensitive to data source: a comparison of field and lab temperature sensitivity data

Abstract A large literature exists on mechanisms driving soil production of the greenhouse gases CO 2 and CH 4 . Although it is common knowledge that measurements obtained through field studies vs. laboratory incubations can diverge because of the vastly different conditions of these environments, few studies have systematically examined these patterns. These data are used to parameterize and benchmark ecosystem- to global-scale models, which are then susceptible to the biases of the source data. Here, we examine how greenhouse gas measurements may be influenced by whether the measurement/incubation was conducted in the field vs. laboratory, focusing on CO 2 and CH 4 measurements. We use Q 10 of greenhouse gas flux (temperature sensitivity) for our analyses because this metric is commonly used in biological and Earth system sciences and is an important parameter in many modeling frameworks. We predicted that laboratory measurements would be less variable, but also less representative of true field conditions. However, there was greater variability in the Q 10 values calculated from lab-based measurements of CO 2 fluxes, because lab experiments explore extremes rarely seen in situ , and reflect the physical and chemical disturbances occurring during sampling, transport, and incubation. Overall, respiration Q 10 values were significantly greater in laboratory incubations (mean = 4.19) than field measurements (mean = 3.05), with strong influences of incubation temperature and climate region/biome. However, this was in part because field measurements typically represent total respiration (Rs), whereas lab incubations typically represent heterotrophic respiration (Rh), making direct comparisons difficult to interpret. Focusing only on Rh-derived Q 10 , these values showed almost identical distributions across laboratory ( n = 1110) and field ( n = 581) experiments, providing strong support for using the former as an experimental proxy for the latter, although we caution that geographic biases in the extant data make this conclusion tentative. Due to a smaller sample size of CH 4 Q 10 data, we were unable to perform a comparable robust analysis, but we expect similar interactions with soil temperature, moisture, and environmental/climatic variables. Our results here suggest the need for more concerted efforts to document and standardize these data, including sample and site metadata.

54 ENVIRONMENTAL SCIENCES↗

Effects of photoevaporation on protoplanetary disc ‘isochrones’

ABSTRACT Protoplanetary discs are the site of star and planet formation, and their evolution and consequent dispersal deeply affect the formation of planetary systems. In the standard scenario they evolve on time-scales ∼Myr due to the viscous transport of angular momentum. The analytical self-similar solution for their evolution predicts specific disc isochrones in the accretion rate–disc mass plane. However, photoevaporation by radiation emitted by the central star is likely to dominate the gas disc dispersal of the innermost region, introducing another (shorter) time-scale for this process. In this paper, we include the effect of internal (X and EUV) photoevaporation on the disc evolution, finding numerical solutions for a population of protoplanetary discs. Our models naturally reproduce the expected quick dispersal of the inner region of discs when their accretion rates match the rate of photoevaporative mass loss, in line with previous studies. We find that photoevaporation preferentially removes the lightest discs in the sample. The net result is that, counter-intuitively, photoevaporation increases the average disc mass in the sample, by dispersing the lightest discs. At the same time, photoevaporation also reduces the mass accretion rate by cutting the supply of material from the outer to the inner disc. In a purely viscous framework, this would be interpreted as the result of a longer viscous evolution, leading to an overestimate of the disc age. Our results thus show that photoevaporation is a necessary ingredient to include when interpreting observations of large disc samples with measured mass accretion rates and disc masses. Photoevaporation leaves a characteristic imprint on the shape of the isochrone. Accurate data of the accretion rate–disc mass plane in the low disc mass region therefore give clues on the typical photoevaporation rate.

Somigliana, Alice↗

Backlighting extended gas halos around luminous red galaxies: Kinematic Sunyaev-Zel’dovich effect from DESI Y1 and ACT data

The gas density profile around galaxies, shaped by feedback and affecting the galaxy lensing signal, is imprinted on the cosmic microwave background (CMB) by the kinematic Sunyaev-Zel’dovich effect (kSZ). We precisely measure this effect (𝑆/𝑁 ≈ 10) via velocity stacking with 825,283 spectroscopically confirmed luminous red galaxies (LRG) from the Dark Energy Spectroscopic Instrument Year 1 (DESI Y1) survey, which overlap with the Atacama Cosmology Telescope (ACT) Data Release 6 temperature maps over ≥ 4,000 deg 2 . We explore the kSZ dependence with various galaxy parameters and find no significant trend with redshift but clear trends with stellar mass and absolute magnitude in 𝑔, 𝑟, and 𝑧 bands. Our analysis suggests that the gas extends beyond the dark matter halo (99.5% confidence level, i.e., probability to exceed (PTE)⁢ = 0.005). We find a tentative preference for hydrodynamical simulation models with stronger feedback that drives gas further out (Illustris 𝑧 = 0.5, PTE⁢ = 0.37) over weaker-feedback cases (IllustrisTNG 𝑧 = 0.8, PTE⁢ = 0.045), though with limited statistical significance. In all cases, a free multiplicative amplitude was fit to the simulated profiles, and further modeling work is required to firm up these conclusions. We find consistency between kSZ profiles around spectroscopic and photometric LRG, with comparable statistical power, thus increasing our confidence in the photometric analysis. Additionally, we present the first kSZ measurement around the DESI Y1 bright galaxy sample (BGS) and the emission-line galaxies (ELG) whose features match qualitative expectations. Finally, we forecast 𝑆/𝑁 ∼ 50 for future stacked kSZ measurements using data from the ACT, the DESI Y3, and the Rubin Observatory. Furthermore, these measurements will serve as an input for galaxy formation models and baryonic uncertainties in galaxy lensing.

79 ASTRONOMY AND ASTROPHYSICS↗

Multiscale Cryo Electron Microscopy Reveals Interfacial Degradation and Stabilization in Battery Electrodes

Electrochemical interfaces are dynamic systems, evolving based on their local environment and reactant surface structures. The electrode-electrolyte interface in Li-ion batteries can be protective, limiting parasitic reactions with the electrolyte to passivate the surface [1]. Additionally, this interphase has an impact on the Li-ion transport through that layer based on its composition, bonding environment, and thickness. These parameters are challenging to collect and may vary depending on the electrode surface site investigated relative to its spatial position in a coin cell. This study will detail a multiscale cryogenic electron microscopy approach where millimeter-scale cross-sections through the coin cell batteries were made using a cryogenic stage within a fs-laser plasma focused ion beam (laser PFIB) with complementary energy dispersive X-ray spectroscopy able to detect variations in the composition at electrode interfaces [2]. Microscale cross-sectioning and lamella sample preparation of battery electrodes was conducted at the Center for Integrated Nanotechnologies using a Ga-ion focused ion beam (FIB) with air-free and cryo-transfer [3], followed by nanoscale mapping of composition and bonding within the CEI through cryo-scanning transmission electron microscopy (cryo-STEM) electron energy loss spectroscopy [4]. This multiscale approach enabled identification of millimeter-scale features of a battery stack with visualization of degradation in electrodes such as cracks in cathode particles, gas evolution, and SEI evolution; microscale interfacial characteristics, such as heterogeneity in the SEI or barrier layer and identification of electrolyte networks to the electrode surfaces; and nanoscale measurement of the CEI thickness, mapping of transition metal bonding within the cathode particles to identify loss of active materials, and identification of beneficial electrolyte additives incorporated into the CEI structure. This multiscale approach allows for a statistical understanding of the primary mechanisms and parasitic degradation pathways that impact performance by limiting the ion transport pathways within Li+ batteries.

36 MATERIALS SCIENCE↗

Laboratory and field assessment of mid-infrared absorption (MIRA) instrument performance for methane and ethane dry mole fractions

Concurrent measurements of methane (CH 4 ) and ethane (C 2 H 6 ) can be used to identify and separate methane sources, as ethane is present in thermogenic sources (e.g., oil and natural gas) but not in biogenic sources (e.g., agriculture). In this study, we evaluated the performance of multiple Aeris MIRA Ultra instruments (Versions 1 and 2) through controlled laboratory tests and tower-based deployments under field conditions. The systems were modified with an external pump, flow control, a Nafion dryer, and a custom-built auxiliary box to automate the system and transmit near real-time data. We determined the best calibration approach for our application, given practical limitations, to be a full calibration cycle (with ambient and high calibration cylinders) about once per day and an ambient calibration cylinder sampled hourly. Measurement uncertainty was assessed, including the uncertainty due to instrument noise as a function of calibration frequency, uncertainty in the water vapor correction, and cylinder assignment uncertainty. Instrument noise was the dominant source of uncertainty for C 2 H 6 , while the water vapor correction dominated the CH 4 uncertainty. For Version 2 systems with hourly calibrations and a Nafion dryer with counterflow, the mean total uncertainty, including both systematic errors and noise, of hourly averages was 0.8–3.0 ppb CH 4 and 0.35–0.37 ppb C 2 H 6 . Laboratory intercomparisons showed network compatibility within 1.2 ppb CH 4 and 0.23 ppb C 2 H6, and a collocated deployment with a NOAA Picarro system agreed within 1.8 ppb CH 4 . Instrument noise varied substantially amongst the instruments, with errors reaching up to 11 ppb CH 4 and 2 ppb C 2 H 6 for hourly means, with similar variability indicated in a 50 h cylinder test. With appropriate engineering and calibration, the Aeris MIRA Ultra has the potential to distinguish regional methane emission sources in many field settings.

03 NATURAL GAS↗

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗

Measuring very low radiation doses in PTFE for nuclear forensic enrichment reconstruction

Every country that has made nuclear weapons has used uranium enrichment to do so. Despite the centrality of this technology to international security, there is still no reliable physical marker of past enrichment in the open literature that can be used to perform forensic verification of historically produced weapons on gas centrifuges. We show that the extremely low radioactivity from uranium alpha emissions during enrichment leaves detectable and irreversible calorimetric signatures in the common enrichment gasket material PTFE, allowing for historical reconstruction of past enrichment activities at a sensitivity better than one weapon’s quantity of highly enriched uranium. Fast scanning calorimetry also enables the measurement of recrystallization enthalpies of sequentially microtomed slices, confirming the magnitude and the type of radiation exposure while also providing detection of tampering and a method for analyzing field samples useful for treaty verification. Furthermore, this work opens the door for common items to be turned into precise dosimeters to detect the past presence of radioactivity, nuclear materials, and related activities with high confidence.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Prediction of Thermal Conditions of DED With FEA Metal Additive Simulation

This paper presents the integration of wire-arc additive manufacturing (WAAM) using Gas Metal Arc Welding (GMAW) into a machine tool to create a retrofit hybrid computer numeric control (CNC) machine tool. GMAW, along with other direct energy deposition systems, has the capacity to deposit material faster than the excess thermal energy can dissipate. This results in the need to allow the part to cool between consecutive layers, which is the most time-consuming part of the additive process. Finite element analysis (FEA) was used in conjunction with monitored build plate surface temperatures during deposition samples to improve adequate dwell time prediction and to develop a cooling system. A deposition was completed where no dwell time was used and the build plate along with the machine table temperatures were monitored. A second deposition was completed where only one bead was deposited and the traverse speed was increased. The GMAW welder was mounted on a 3-axis CNC machine where two square deposition samples were completed. A FEA model was designed and verified using the monitored samples. The model will be used to determine improved depositions speeds and whether forced cooling would allow for an increased deposition rate without structural failure. It was determined the FEA software can be used to accurately model and predict the thermal response of WAAM AM components.

Heinrich, Lauren↗

Process-driven roadmap for depositing super duplex stainless steel via wire Arc additive manufacturing

Here, this study systematically investigates the effects of shielding gas, bead spacing, weld mode, and travel speed on the phase balance, porosity, and hardness of wire arc additively manufactured (WAAM) super duplex stainless steel (ER2594). Robotic WAAM was employed to fabricate multilayer walls under systematically varied process conditions, followed by phase transformation simulations, X-ray computed tomography (XCT), electron backscatter diffraction (EBSD), and microhardness evaluation. Thermodynamic simulations predicted rapid cooling of AM process can suppress the potential formation of deleterious precipitates which was later validated via cross-sectional microstructure analyses of printed samples. XCT revealed porosity levels below 0.2% for all deposits, with reduced travel speed significantly lowering defect volume. Microstructural analyses revealed the evolution of various austenite precipitates, including grain boundary austenite (GBA), Widmanstätten austenite (WA), and intergranular austenite (IGA), sequentially upon cooling of the ferrite phase. Among all process parameters, weld transfer mode exhibited the strongest influence on phase balance; pulsed mode promoted higher ferrite retention (~ 36%) compared to RapidX mode. No consistent relationship between stabilized phase fraction and captured microhardness was observed. This work provides critical insights for optimizing WAAM parameters to control phase balance and mechanical performance, which is essential for producing high-integrity super duplex stainless-steel components for nuclear and marine applications.

Grain orientation↗

Revisiting stellar properties of star-forming galaxies with stellar and nebular spectral modelling

Spectral synthesis is a powerful tool for interpreting the physical properties of galaxies by decomposing their spectral energy distributions (SEDs) into the main luminosity contributors (e.g. stellar populations of distinct age and metallicity or ionised gas). However, the impact nebular emission has on the inferred properties of star-forming (SF) galaxies has been largely overlooked over the years, with unknown ramifications to the current understanding of galaxy evolution. The objective of this work is to estimate the relations between stellar properties (e.g. total mass, mean age, and mean metallicity) of SF galaxies by simultaneously fitting the stellar and nebular continua and comparing them to the results derived through the more common purely stellar spectral synthesis approach. The main galaxy sample from SDSS DR7 was analysed with two distinct population synthesis codes: FADO, which estimates self-consistently both the stellar and nebular contributions to the SED, and the original version of STARLIGHT, as representative of purely stellar population synthesis codes. Differences between codes regarding average mass, mean age and mean metallicity values can go as high as ~0.06 dex for the overall population of galaxies and ~0.12 dex for SF galaxies (galaxies with EW(Hα) > 3 Å), with the most prominent difference between both codes in the two populations being in the light-weighted mean stellar age. FADO presents a broader range of mean stellar ages and metallicities for SF galaxies than STARLIGHT, with the latter code preferring metallicity solutions around the solar value (Z ⊙ = 0.02). A closer look into the average light- and mass-weighted star formation histories of intensively SF galaxies (EW(Hα) > 75 Å) reveals that the light contributions of simple stellar populations (SSPs) younger than ≤10 7 (10 9 ) years in STARLIGHT are higher by ~5.41% (9.11%) compared to FADO. Moreover, FADO presents higher light contributions from SSPs with metallicity ≤ Z ⊙ /200 (Z ⊙ /50) of around 8.05% (13.51%) when compared with STARLIGHT. This suggests that STARLIGHT is underestimating the average light-weighted age of intensively SF galaxies by up to ~0.17 dex and overestimating the light-weighted metallicity by up to ~0.13 dex compared to FADO (or vice versa). The comparison between the average stellar properties of passive, SF and intensively SF galaxy samples also reveals that differences between codes increase with increasing EW(Hα) and decreasing total stellar mass. Moreover, comparing SF results from FADO in a purely stellar mode with the previous results qualitatively suggests that differences between codes are primarily due to mathematical and statistical differences and secondarily due to the impact of the nebular continuum modelling approach (or lack thereof). However, it is challenging to adequately quantify the relative role of each factor since they are likely interconnected. This work finds indirect evidence that a purely stellar population synthesis approach negatively impacts the inferred stellar properties (e.g. mean age and mean metallicity) of galaxies with relatively high star formation rates (e.g. dwarf spirals, ‘green peas’, and starburst galaxies). In turn, this can bias interpretations of fundamental relations such as the mass-age or mass-metallicity, which are factors worth bearing in mind in light of future high-resolution spectroscopic surveys at higher redshifts (e.g. MOONS and 4MOST-4HS).

79 ASTRONOMY AND ASTROPHYSICS↗

An [O iii ] search for extended emission around AGN with H i mapping: a distant cloud ionized by Mkn 1

ABSTRACT Motivated by the discovery of large ionized clouds around AGN, and particularly the large fraction of those that are consistent with photoionized gaseous tidal debris, we searched for [O iii] emission around Seyfert galaxies previously mapped in H i, many with extended gas features. Of 26 Seyfert galaxies, we find one spatially extended emission feature, a discrete cloud projected ≈12 kpc SW from the centre of Mkn 1 and spanning a transverse extent of 8 kpc. Optical spectroscopy (Kast/Lick and SCORPIO/BTA) of this cloud confirms its association with the Mkn 1–NGC 451 galaxy pair, closely matching the kinematics of nearby H i structures, and reveals emission-line ratios requiring photoionization by the AGN at roughly the direct observed luminosity of the nucleus. For the entire sample, the full opening angle of the ionization cones (bicones) must be <20° if the AGNs are continuously bright for scales longer than the light-traveltimes to the H i structures. Since typical AGN ionization cones are observed to be much broader than this, our low detection fraction may add to evidence for the ubiquity of strong variations in AGN luminosity on scales 104–105 yr.

Knese, Erin Darnell↗

Technical note: 21 Ne in the CoQtz-N quartz standard material

Intercomparison standards produced from mineral samples exposed to the natural cosmic ray flux are routinely used for interlaboratory comparison and normalization of measurements of the cosmogenic noble gases 3 He and 21 Ne. This effort is facilitated by the availability of multiple standard materials with a wide range of cosmogenic nuclide concentrations. The “CoQtz-N” quartz standard, which was originally produced and distributed as an intercomparison standard for cosmogenic 10 Be and 26 Al, has a significantly lower cosmogenic nuclide concentration than other mineral standards used for cosmogenic noble gas analysis and is therefore potentially useful for assessing the linearity of interlaboratory offsets across a wide range of concentrations. This paper reports 21 Ne analysis of 13 aliquots of CoQtz-N, interspersed with 14 aliquots of the commonly used CRONUS-A quartz standard, in three analytical sessions on two noble gas mass spectrometer systems. The excess 21 Ne concentration in CoQtz-N, normalized to the accepted value of 320 × 10 6 atoms g −1 for CRONUS-A, is 13.87 ± 0.24 × 10 6 atoms g −1 . Alternatively, the ratio of excess 21 Ne concentrations in CoQtz-N and CRONUS-A is 0.04330 ± 0.00077.

Balco, Greg [Lawrence Livermore National Laborator↗

Probing Pore Size and Connectivity in Porous Silicas Using 13C MAS NMR Spectroscopy of Supercritical Methane

Measuring the pore size and pore-size distributions and exploring the fluid-exchange dynamics between different types of pores in porous materials remains a significant experimental challenge but is critical to understanding catalysis, chromatography, nutrient cycling, and a whole range of geochemical phenomena, including shale gas and tight gas extraction. Here, we present the results of 1D 13 C NMR and 2D exchange spectroscopy (EXSY) NMR investigations of a porous silica using supercritical methane (scCH 4 ) as a direct probe of pore size and fluid exchange between pore types. The results show that the 13 C chemical shift of scCH 4 adsorbed in nanometer-scale silica pores becomes more negative with increasing pore diameter, in agreement with trends reported for gas hydrates, zeolites, MOFs, and clays and other microporous (<10 nm pores) geochemical materials. These 13 C chemical shifts follow a natural log–linear trend with pore size in the vacuum-dried porous silicas studied here, allowing one to predict pore size based on the 13 C chemical shift in dry silica nanopores. The EXSY and 1D 13 C NMR results both show that CH 4 exchanges between pore and bulk fluid environments over rate scales from 0.01 to 1 kHz in vacuum-dried samples and that exchange dynamics must be considered when interpreting 13 C NMR of pore-adsorbed CH 4 . Introducing H 2 O to the system causes the 13 C chemical shift to become more negative with increasing H 2 O content as a result of H 2 O preferentially filling small pores, forcing CH 4 to occupy larger pores that are better connected to the bulk environment. Likewise, the 1D 13 C data show a decreased distribution of exchange rates between pore-adsorbed and bulk CH 4 in the presence of H 2 O.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Disc dichotomy signature in the vertical distribution of [Mg/Fe] and the delayed gas infall scenario

Context. Analysis of the Apache Point Observatory Galactic Evolution Experiment project (APOGEE) data suggests the existence of a clear distinction between two sequences of disc stars in the [α/Fe] versus [Fe/H] abundance ratio space, known as the high- and low-α sequence, respectively. This dichotomy also emerges from an analysis of the vertical distribution of the [α/Fe] abundance ratio. Aims. We aim to test whether the revised two-infall chemical evolution models designed to reproduce the low- and high-α sequences in the [α/Fe] versus [Fe/H] ratios in the solar neighbourhood are also capable of predicting the disc bimodality observed in the vertical distribution of [Mg/Fe] in APOGEE DR16 data. Methods. Along with the chemical composition of the simple stellar populations born at different Galactic times predicted by our reference chemical evolution models in the solar vicinity, we provide their maximum vertical height above the Galactic plane |zmax| computed assuming the relation between the vertical action and stellar age in APOGEE thin-disc stars. Result. The vertical distribution of the [Mg/Fe] abundance ratio predicted by the reference chemical evolution models is in agreement with that observed when combining the APOGEE DR16 data (chemical abundances) with the astroNN catalogue (stellar ages, orbital parameters) for stars younger than 8 Gyr (only low-α sequence stars). Including the high-α disc component, the dichotomy in the vertical [Mg/Fe] abundance distribution is reproduced considering the observational cut in the Galactic height of |z|< 2 kpc. However, our model predicts an overly flat (almost constant) growth of the maximum vertical height |zmax| quantity as a function of [Mg/Fe] for high-α objects in contrast with the median values from APOGEE data. Possible explanations for such a tension are that: (i) the APOGEE sample with |z|< 2 kpc is more likely than ours to be contaminated by halo stars, causing the median values to be kinematically hotter, and (ii) external perturbations – such as minor mergers – that the Milky Way experienced in the past could have heated up the disc, and the heating of the orbits cannot be modeled by only scattering processes. Assuming a disc dissection based on chemistry for APOGEE-DR16 stars (|z|< 2 kpc), the observed |zmax| distributions for high-α and low-α sequences are in good agreement with our model predictions if we consider the errors in the vertical action estimates in the calculation. Moreover, a better agreement between predicted and observed stellar distributions at different Galactic vertical heights is achieved if asteroseismic ages are included as a constraint in the best-fit model calculations. Conclusions. The signature of a delayed gas infall episode, which gives rise to a hiatus in the star formation history of the Galaxy, are imprinted both in the [Mg/Fe] versus [Fe/H] relation and in vertical distribution of [Mg/Fe] abundances in the solar vicinity.

79 ASTRONOMY AND ASTROPHYSICS↗

Characterizing mineralization on low carbon steel exposed to aerated and degassed synthetic hydraulic fracture fluids

This study investigates the mineralization occurring at the interface between injected hydraulic fracturing fluids and steel production casing during the shut-in period of unconventional shale wells. Mild steel coupons were reacted with synthetic hydraulic fracturing fluids with varying base fluid and dissolved gas concentrations. Experiments were carried out in an autoclave system set at 50 °C and 2000 PSI for 2 and 14 days. Physical and mineralogical changes to the steel coupons’ surface were characterized using an FEI Quanta 600 field emission gun (FEG) scanning electron microscope (SEM) and a PANalytical XPert Pro diffractometer. Barite precipitation occurred ubiquitously during the first 48 hours in all experimental scenarios. Sulfate radicals created from degradation and reduction of ammonium persulfate breakers facilitate barite formation. Concomitant barite and corrosion related precipitates on the sample surfaces suggest iron hydroxy salts act as nucleation sites for mineral scale growth. These results suggest hydraulic fracturing fluids may have deleterious effects on the wellbore before production of the well begins.

36 MATERIALS SCIENCE↗

Well Stimulation Treatment in California: Evaluation of Disclosure Data, May 2015 – October 2019

In this document, disclosure data from 1,228 well stimulations occurring May 2015 to October 2019 in California are evaluated. This evaluation updates a previous study that was based on 618 well stimulations occurring May 2015 to June 2016 (Stringfellow, W.T., Camarillo, M.K., and Jordan, P. 2017, Status of Well Stimulation in California Since Implementation of SB-4 Regulations, Berkeley National Laboratory, Berkeley, CA). While the goal of the previous study was to provide a summary of information obtained since passage of California Senate Bill No. 4—Oil and Gas, the goal of the current evaluation is to provide a basis for studying chemical indicators that could potentially be used to detect aquifer contamination. We evaluate chemical indicators is a separate document using the data contained herein as well as data from monitoring wells located within oil fields. Compared with the data used by Stringfellow et al. 2017, the current evaluation is based on a more diverse data set. While the previous study contained data for only two oil fields with more than 30 well stimulations, the current data set contains four oil fields with more than 30 well stimulations, making these data more ideal for comparisons using statistical tests. More producers and a new oil field, Buena Vista Nose, are represented in the current data set. Some well stimulation practices remain relatively unchanged since the previous study. Well stimulation is mostly occurring in Kern County with the exception of a single well stimulation in Orange County. Almost all well stimulations are hydraulic fracturing. The current data set contains two acid fracturing treatments and one matrix acidizing treatment. The median number of chemicals added per well stimulation—excluding water and proppant—was previously 21; the number in the expanded data set is 20. Median water added per well stimulation was previously 89,000 gallons and is now 98,000 gallons. While this water use represents a 10% increase, water use for hydraulic fracturing in California is still lower than water use in other oil and gas fields. Chemical formulations appear to have shifted since the previous study. This shift may be related to a change in the predominant service company. We identified 26 chemicals for which the frequency of use has changed by more than 30%. The total number of chemicals used has also expanded. Previously, 178 unique chemicals were identified as being added to well stimulation fluids. The total number of unique chemicals is now 205. Analytical data available for base and recovered fluids has expanded. The number of base fluid samples has increased from 12 to 35 and the number of recovered fluid samples has increased from 1,078 to 2,166. The expanded data set is more ideal for an evaluation of indicator chemicals and comparisons across different formations. The analytical data for recovered fluid samples indicates that many ions, radioactive constituents, and organics are consistently observed, making these chemicals ideal for consideration as potential indicators of aquifer contamination.

54 ENVIRONMENTAL SCIENCES↗

Manufacturing Dissolvable Alloy Components using ShAPE: A Study on Solid Phase Processing of Mg-W Composites and WJ11 Alloys

Dissolvable alloys and composites are an emerging class of materials that demonstrate tailored sorptivity in corrosive environments. This work explored the viability of solid phase processing (SPP) techniques, namely the shear assisted processing and extrusion (ShAPETM) method, to manufacture dissolvable magnesium composites and alloys components such as rods and tubes. The study also determined the effects of material composition and manufacturing process conditions on material microstructures developed during SPP and the resulting performance of the components. Explicit properties of interest included ultimate tensile strength, ultimate compressive strength, and yield strength. The application fields of interest for dissolvable alloys were identified as oil-and-gas operations and biomedical implants. Accordingly, PNNL collaborated with industrial and academia partners, Fortek Industries, Houston and University of Pittsburgh, during the course of this project for material and ShAPE process development. PNNL determined the viability of the using ShAPE to process the custom-designed materials provided by the project partners. This was done by identifying process parameters such as tool rotation rate, tool plunge rate, and process cooling optimal for manufacturing components with consolidated microstructures. Subsequently, PNNL also performed microstructural characterization on unprocessed and processed samples and mechanical property testing. One of the major findings from this work is that ShAPE was able to manufacture dissolvable magnesium composite and alloy rods and tubes with consolidated homogeneous microstructures and minimal macroscale defects on component surfaces. It was observed that samples processed via ShAPE demonstrated an average grain size < 2 - 5 µm, which was markedly lower than that of the precursors with 8 – 13 µm grains. Results showed that the ShAPE synthesized dissolvable magnesium composite and alloy strength was on par with or better than those components that were manufactured using traditional manufacturing processes such as forging and extrusion. It is noteworthy that the ShAPE samples were made with considerably lower number of process steps.

36 MATERIALS SCIENCE↗