Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine Materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Campaign 78 - Production of 252 Cf and the Recovery of Curium Feed Material at the Radiochemical Engineering Development Center

The production of californium-252 (Cf-252) has been of interest to the US Department of Energy (DOE) since the 1970s because of its ability to emit neutrons (2.31 x 10 12 neutrons/gram second). Today, Oak Ridge National Laboratory is responsible for the majority of Cf-252 sold around the world. This report aims to provide a complete summary of the chemical processing of the Cf and curium (Cm) from campaign 78 (C78) which started in January 2019.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Additive Manufacturing of Corrosion Resistant UHTC Materials for Chloride Salt-to-sCO2 Brayton Cycle Heat Exchangers

The objectives of the project include: (1) screen high-purity, high density ultra-high-temperature ceramics (UHTCs) for chloride salt corrosion resistance, (2) develop binder-jet additive manufacturing and sintering for ZrB 2 -MoSi 2 blends using literature and experiments to demonstrate feasibility, and (3) evaluate chloride salt corrosion resistance of additively manufactured ZrB 2 -MoSi 2 . These initial objectives support the development of a durable and reliable ultra-compact high-efficiency salt-to-sCO 2 heat exchanger for closed-loop Brayton power cycles based on corrosion resistant, high-strength, thermally conductive UHTC materials and novel designs enabled by additive manufacturing. The UHTC materials are also abrasion resistant so that they could be applicable to all three thermal carrier media pathways identified in the CSP Gen3 Roadmap.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Engineering evaluations of nuclear material storage containers against the packaging requirements at TA-55 (FY22 Rules of Use Report)

A set of obligations in the yearly storage container surveillance program, ensures that a retrospective approach is applied with loaded containers in inventory to confirm compliance with all “users” to ensure nuclear material storage container requirements are being followed. Validation that packaged containers are properly used, within a specific set of container types prescribed “bounding conditions of use,” is based on meeting requirements as identified in operating procedures associated with TA55-DOP-091, TA-55 Nuclear Material Packaging, and PA-RD-01022, Nuclear Material Packaging Requirements. The surveillance plan obligation requires the application of local area nuclear material accountability software or (LANMAS) to produce queries. The data queries are used to assess attributes of containers in storage these investigations are conducted on a bi-annual basis. This rules of use (ROU) compliance process ensures proper usage of storage containers as containment systems and therefore provides effective worker protection. It is structured as a supporting effort by implementing aspects of PA-AP-01207, Nuclear Material Container Safety Management at TA-55.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Developing a Fundamental Knowledge Base for the Interaction of Ruthenium with Natural and Engineered Iron-Bearing Materials

The intent of this project is to build a fundamental knowledge base concerning the redox coupling between Ru and Fe in heterogeneous systems with predictive applications towards the fate, speciation, and transport of Ru in the environment and its capture using available technologies. RuNOCl 3 and Fe 3+ are redox active over a broad range of pH. Initial assessment of effect of redox coupling between Ru and Fe indicates that Fe(III) in ferrihydrite can oxidize Ru 2+ in RuNOCl3 to Ru(IV) during coprecipitation at ambient conditions and alkaline pH. Further, evidence suggests that Ru(IV) is incorporated in the structure of fh. Likewise, Fe 3+ (aq) also reduces Ru 2+ in RuNOCl 3 in the homogenous system at acidic pH although the kinetics of reaction appear to be slow. Rufh annealed to 500 0C transforms to Ru(III) doped hematite. AIMD informed EXAFS indicates that Ru substitutes for Fe(III) in regular octahedral sites of hematite but requires three distinct configurations involving edge-sharing protonated Fe vacancies and straight substitution with no local defects. Fe 2+ (aq) appears to oxidize at the surface of RuO 2 , but the amount is too low to reasonably expect detectable reduced Ru. Future experiments at higher pH are warranted to make Fe 2+ (aq) less stable (i.e., make more redox active). We also demonstrated that we can functionalize Si aerogels with Fe(II) and Fe(III) but likely need to go to higher T to make Feo nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Prioritizing Off-Gas Metrics: A Guide for Comparable Off-Gas Capture Testing

The Material Recovery and Waste Form Development (MRWFD) off-gas team had a workshop, hosted by Idaho National Laboratory (INL), to align goals and expectations for off-gas research. The workshop included team members from four national laboratories. The workshop focused on defining distinct R&D phases with specific metrics, outlining standard test and measurement protocols for Iodine and Krypton/Xenon sorbents, brainstorming approaches to future disruptive technologies, and recognizing parameters with more inherent risk, requiring more rigorous evaluation. This report will serve as a guide for future off-gas work. Its purpose is to foster efficient collaboration across diverse research facilities and invite direct comparison of materials and results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

SynthEsizing Novel H2 Sensors for Operational Resilience in Pipeline Infrastructure (SENSOR)

A flexible and extensible computational framework acts as a black-box materials discovery engine, capable of screening, predicting, and designing advanced materials with minimal manual intervention was developed. While developed for hydrogen sensing, the approach can be readily adapted to other materials challenges, offering a powerful tool for data-driven materials innovation.

08 HYDROGEN↗
NASA NTRS1979

Materials for Advanced Turbine Engines: Power Metallurgy Rene 95 Rotating Turbine Engine Parts - Volume 1

An attempt was made to improve methods for producing powder metallurgy aircraft gas turbine engine parts from the nickel base superalloy known as Rene 95. The parts produced were the high pressure turbine aft shaft for the CF6-50 engine and the stages 5 through 9 compressor disk forgings for the CFM56/F101 engines. A 50% cost reduction was achieved as compared to conventional cast and wrought processing practices. An integrated effort involving several powder producers and a major forging source were included.

Pfouts, W. R.↗
NASA NTRS1982

Materials for advanced turbine engines. Volume 1: Advanced blade tip seal system

Project 3, the subject of this technical report, was structured toward the successful engine demonstration of an improved-efficiency, long-life, tip-seal system for turbine blades. The advanced tip-seal system was designed to maintain close operating clearances between turbine blade tips and turbine shrouds and, at the same time, be resistant to environmental effects including high-temperature oxidation, hot corrosion, and thermal cycling. The turbine blade tip comprised an environmentally resistant, activated-diffussion-bonded, monocrystal superalloy combined with a thin layer of aluminium oxide abrasive particles entrapped in an electroplated NiCr matrix. The project established the tip design and joint location, characterized the single-crystal tip alloy and abrasive tip treatment, and established the manufacturing and quality-control plans required to fully process the blades. A total of 171 blades were fully manufactured, and 100 were endurance and performance engine-tested.

Zelahy, J. W.↗
NASA NTRS1982

Materials for advanced turbine engines. Project 2: Rene 150 directionally solidified superalloy turbine blades, volume 2

The results of the engine testing of Rene 150 Stage 1 high pressure turbine blades in CF6-50 core and fan engines are presented. The core engine test was conducted for 233 hours with a variety of test cycles, and the fan engine test was conducted for 1000 C cycles. Post-test analysis of the core engine test data confirmed the suitability of the Rene 150 HPT blade for fan engine testing. Post-test evaluation and analysis of the fan engine test blades included visual and dimensional inspection as well as metallographic examination of selected blades. The Rene 150 HPT blade met the target goal of this project by demonstrating increased metal temperature capability; however, the post-test analysis revealed several areas that would have to be addressed in designing a long-life Rene 150 CF6-50 HPT blade.

Deboer, G. J.↗
NASA NTRS1986

Life prediction and constitutive models for engine hot section anisotropic materials program

This report presents the results of the first year of a program designed to develop life prediction and constitutive models for two coated single crystal alloys used in gas turbine airfoils. The two alloys are PWA 1480 and Alloy 185. The two oxidation resistant coatings are PWA 273, an aluminide coating, and PWA 286, an overlay NiCoCrAlY coating. To obtain constitutive and/or fatigue data, tests were conducted on coated and uncoated PWA 1480 specimens tensilely loaded in the 100 , 110 , 111 , and 123 directions. A literature survey of constitutive models was completed for both single crystal alloys and metallic coating materials; candidate models were selected. One constitutive model under consideration for single crystal alloys applies Walker's micromechanical viscoplastic formulation to all slip systems participating in the single crystal deformation. The constitutive models for the overlay coating correlate the viscoplastic data well. For the aluminide coating, a unique test method is under development. LCF and TMF tests are underway. The two coatings caused a significant drop in fatigue life, and each produced a much different failure mechanism.

Swanson, G. A.↗
NASA NTRS1984

Life prediction and constitutive models for engine hot section anisotropic materials

The development of directionally solidified and single crystal alloys is perhaps the most important recent advancement in hot section materials technology. The objective is to develop knowledge that enables the designer to improve anisotropic gas turbine parts to their full potential. Two single crystal alloys selected were PWA 1480 and Alloy 185. The coatings selected were an overlay coating, PWA 286, and an aluminide diffusion coating, PWA 273. The constitutive specimens were solid and cylindrical; the fatigue specimens were hollow and cylindrical. Two thicknesses of substrate are utilized. Specimens of both thickness (0.4 and 1.5 mm) will be coated and then tested for tensile, creep, and fatigue properties.

Swanson, G. A.↗
NASA NTRS1987

Life prediction and constitutive models for engine hot section anisotropic materials

The results are presented of a program designed to develop life prediction and constitutive models for two coated single crystal alloys used in gas turbine airfoils. The two alloys are PWA 1480 and Alloy 185. The two oxidation resistant coatings are PWA 273, an aluminide coating, and PWA 286, an overlay NiCoCrAlY coating. To obtain constitutive and fatigue data, tests were conducted on uncoated and coated specimens loaded in the CH76 100 CH110 , CH76 110 CH110 , CH76 111 CH110 and CH76 123 CH110 crystallographic directions. Two constitutive models are being developed and evaluated for the single crystal materials: a micromechanic model based on crystallographic slip systems, and a macroscopic model which employs anisotropic tensors to model inelastic deformation anisotropy. Based on tests conducted on the overlay coating material, constitutive models for coatings also appear feasible and two initial models were selected. A life prediction approach was proposed for coated single crystal materials, including crack initiation either in the coating or in the substrate. The coating initiated failures dominated in the tests at load levels typical of gas turbine operation. Coating life was related to coating stress/strain history which was determined from specimen data using the constitutive models.

Swanson, G. A.↗
NASA NTRS1985

Life prediction and constitutive models for engine hot section anisotropic materials program

The purpose is to develop life prediction models for coated anisotropic materials used in gas temperature airfoils. Two single crystal alloys and two coatings are now being tested. These include PWA 1480; Alloy 185; overlay coating, PWA 286; and aluminide coating, PWA 273. Constitutive models are also being developed for these materials to predict the plastic and creep strain histories of the materials in the lab tests and for actual design conditions. This nonlinear material behavior is particularily important for high temperature gas turbine applications and is basic to any life prediction system.

Swanson, G. A.↗