Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Hydrodynamic Impact-Load Alleviation with a Penetrating Hydro-Ski

A penetrating hydro-ski was mounted below a model tested previously in the study reported in NACA Technical Note 4401, and a series of impacts were made in the Langley impact basin to determine load alleviation with this type of hydro-ski. The hydro-ski was designed to penetrate through seaway irregularities with a minimum of drag and with small impact loads. The penetrating hydro-ski was small (beam-loading coefficient of 111) and of a streamline shape with the bottom designed for flush retraction into the main model. A series of impacts at fixed trim angles of 8, 16, and 30 deg were made in smooth water and at a fixed trim angle of 8 deg in rough water. The loads and motions of the model were recorded, and photographic observations of the flow and cavities generated in the water by the penetrating hydro-ski were made. The data are presented and the maximum impact loads and maximum drafts of the model with the penetrating hydro-ski are compared with those of the model obtained without the penetrating hydro-ski. Maximum load reductions of 30 to 70 percent in smooth water and of 50 to 80 percent in rough water are indicated. Cavity and flow generation by the penetrating hydro-ski are discussed, and it is indicated that the penetrating hydro-ski moved smoothly through the water and generated deep cavities which are shown by stereophotographs.

Edge, Philip M., Jr.↗
NASA NTRS1994

Measuring the Thermal Accommodation Coefficient while Aerobraking Magellan

The Magellan spacecraft was inserted into an elliptical orbit around the planet Venus on August 10, 1990. A small aerodynamic force was applied later to the spacecraft for 730 consecutive orbits to lower the apoapsis of the orbit from 8500 km to 541 km. Atmospheric drag removed a maximum of 2 m/sec per orbit from the velocity at periapsis for a total delta-V of 1200 m/sec. This paper will discuss the thermal accommodation coefficient which was inferred from one of the four solar panel temperature measurements from the aerobraking pass through the atmosphere.

measurements thermal accomodation coefficient↗
NASA NTRS1992

Installation effects of wing-mounted turbofan nacelle-pylons on a 1/17-scale, twin-engine, low-wing transport model

A twin-engine, low-wing transport model, with a supercritical wing of aspect ratio 10.8 designed for a cruise Mach number of 0.77 and a lift coefficient of 0.55, was tested in the Langley 16-Foot Transonic Tunnel. The purpose of this test was to compare the wing-nacelle interference effects of flow-through nacelles simulating superfan engines (very high bypass ratio (BPR is approx. = 18) turbofan engines) with the wing-nacelle interference effects of current-technology turbofans (BPR is approx. = 6). Forces and moments on the complete model were measured with a strain-gage balance, and extensive external static-pressure measurements (383 orifice locations) were made on the wing, nacelles, and pylons of the model. Data were taken at Mach numbers from 0.50 to 0.80 and at model angles of attack from -4 deg to 8 deg. Test results indicate that flow-through nacelles with a very high bypass ratio can be installed on a low-wing transport model with a lower installation drag penalty than for a conventional turbofan nacelle at a design cruise Mach number of 0.77 and lift coefficient of 0.55.

Pendergraft, Odis C., Jr.↗
DOE OSTI2023

Multifidelity Approach to Sensitivity Estimation in Large-Eddy Simulation

A novel approach to compute affordable approximate sensitivities in a large-eddy simulation (LES) is proposed and assessed. The approach is based on solving a Reynolds-averaged Navier–Stokes (RANS) problem that has been linearized around the mean LES solution, with closure modeling required for the linearized changes in turbulent Reynolds stresses. In the present study, the closure modeling is based on a linearized algebraic turbulence model. The method is assessed for the flow over a NACA0012 airfoil at a fixed angle of attack, with the Reynolds number as the variable parameter. The results show that, provided an accurate linearized closure model, the method predicts the correct sensitivity of the skin friction coefficient and the mean velocity field at the cost of a linearized RANS, which provides an important proof-of-concept for this approach. Here, the linearized algebraic turbulence model with standard model coefficients produces a reasonably accurate sensitivity, but the results also suggest that accuracy could be gained from recalibrating the model coefficients for this new use of the model.

42 ENGINEERING↗
NASA NTRS2013

Investigations of Fluid-Structure-Coupling and Turbulence Model Effects on the DLR Results of the Fifth AIAA CFD Drag Prediction Workshop

The accurate calculation of aerodynamic forces and moments is of significant importance during the design phase of an aircraft. Reynolds-averaged Navier-Stokes (RANS) based Computational Fluid Dynamics (CFD) has been strongly developed over the last two decades regarding robustness, efficiency, and capabilities for aerodynamically complex configurations. Incremental aerodynamic coefficients of different designs can be calculated with an acceptable reliability at the cruise design point of transonic aircraft for non-separated flows. But regarding absolute values as well as increments at off-design significant challenges still exist to compute aerodynamic data and the underlying flow physics with the accuracy required. In addition to drag, pitching moments are difficult to predict because small deviations of the pressure distributions, e.g. due to neglecting wing bending and twisting caused by the aerodynamic loads can result in large discrepancies compared to experimental data. Flow separations that start to develop at off-design conditions, e.g. in corner-flows, at trailing edges, or shock induced, can have a strong impact on the predictions of aerodynamic coefficients too. Based on these challenges faced by the CFD community a working group of the AIAA Applied Aerodynamics Technical Committee initiated in 2001 the CFD Drag Prediction Workshop (DPW) series resulting in five international workshops. The results of the participants and the committee are summarized in more than 120 papers. The latest, fifth workshop took place in June 2012 in conjunction with the 30th AIAA Applied Aerodynamics Conference. The results in this paper will evaluate the influence of static aeroelastic wing deformations onto pressure distributions and overall aerodynamic coefficients based on the NASA finite element structural model and the common grids.

Keye, Stefan↗
NASA NTRS1975

The effect of Reynolds number on boattail drag

An investigation has been conducted in the Langley pilot transonic cryogenic tunnel to determine the effects of varying Reynolds number on boattail drag at subsonic speeds. Six boattailed cone-cylinder nacelle models were tested with the jet exhaust simulated by a cylindrical sting. Reynolds number was varied from about 2.6 million to 132 million by changing model length and unit Reynolds number. Boattail pressure coefficient distributions show that increasing Reynolds number tends to make the pressure coefficients in the expansion region more negative and the pressure coefficients in the recompression region more positive. These two effects were compensating and as a result there was little or no effect of Reynolds number on the pressure drag of the isolated boattails.

Reubush, D. E.↗
DOE OSTI2022

Novel Patterned Surfaces for Improved Condenser Performance in Power Plants

In this project, we seek to improve the thermoelectric power plant performance through engi-neered nonwetting condenser tube surface designs that can enhance heat transfer performance by: (1) promoting dropwise condensation of the steam on the shell side and eliminating flooding of the surface structure by maintaining low droplet adhesion, thus increasing condensation heat transfer coefficient; (2) deterring fouling and corrosion, thereby reducing fouling resistance and improving heat transfer; (3) possibly reducing drag and increasing convective heat transfer inside coolant tubes; and (4) reducing the number of tubes, coolant water usage, and levelized cost of condenser.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1978

Aerodynamic characteristics of a jet sheet vortex generator

A configuration concept for augmenting the lift capability of low aspect ratio, thin wings, typically used on fighter aircraft was investigated. The fluid strake concept uses a jet sheet formed by blowing from a series of small orifices located in the side of the fuselage ahead of the wing to generate a stable vortex flow over the wing at high angle of attack. The effect of the location of the fluid strake relative to the wing was investigated for three different designs of the in-line orifices using a half-span model tested in a 7 by 10 foot low speed tunnel. Based on the results of the low speed test, a jet sheet producing module was incorporated into a NASA general research fighter model and tested in the Langley 7 by 10 foot high speed tunnel to determine the effectiveness of the fluid strake as a lift-enhancement device in the high-speed maneuver regime. Tests were conducted over a Mach number range from 0.3 to 0.8, with a jet momentum coefficient range from 0 to 0.24. Significant lift increments resulted at the higher angles of attack and drag polars were improved.

Ziegler, H.↗
NASA NTRS1981

Design and experimental results for a flapped natural-laminar-flow airfoil for general aviation applications

A flapped natural laminar flow airfoil for general aviation applications, the NLF(1)-0215F, has been designed and analyzed theoretically and verified experimentally in the Langley Low Turbulence Pressure Tunnel. The basic objective of combining the high maximum lift of the NASA low speed airfoils with the low cruise drag of the NACA 6 series airfoils has been achieved. The safety requirement that the maximum lift coefficient not be significantly affected with transition fixed near the leading edge has also been met. Comparisons of the theoretical and experimental results show generally good agreement.

Somers, D. M.↗
NASA NTRS1983

Venus gravity field - Pioneer Venus Orbiter navigation results

The gravity field of Venus has been modeled by a spherical harmonic expansion of the potential to degree and order seven. The estimates of these coeficients were obtained by combining information from 43 short arcs (4 hr) of line-of-sight Doppler data centered at periapsis. The data arcs were distributed in longitude and time over more than two circulations of Venus by the Pioneer Venus Orbiter subperiapsis point which was confined to the band of latitudes from 14 deg N to 17 deg N. Convergence of the solution has been assured by iterating upon the initial estimate. All estimates were performed with zero a priori information on the gravity coefficients. Since the altitude of periapsis for most of the orbits was within the sensible Venusian atmosphere, drag effects on the estimated harmonics have been removed using an exponential atmosphere density model. Estimates of the mass parameter (GM) of Venus using this dataset are also evaluated.

Williams, B. G.↗
NASA NTRS1932

Tests of N.A.C.A. airfoils in the variable-density wind tunnel Series 24

This note is the fifth of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests of a group of six low-cambered airfoils in the variable-density wind tunnel. The mean camber lines are identical for the six airfoils and are of such a form that the maximum mean camber is 2 per cent of the chord and is at a position 0.4 of the chord behind the loading edge. The airfoils differ in thickness only, the maximum-thickness/chord ratios being 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results have been presented in the form of both infinite and finite aspect-ratio characteristics. The values of C(sub L) max/C(sub d) degrees min for this group of airfoils are among the highest thus far obtained, the minimum profile drags being approximately equal to those for the symmetrical series of corresponding thickness, while the maximum lift coefficients are considerably higher.

Jacobs, Eastman N↗
NASA NTRS1995

A simulation to study the feasibility of improving the temporal resolution of LAGEOS geodynamic solutions by using a sequential process noise filter

A key drawback to estimating geodetic and geodynamic parameters over time based on satellite laser ranging (SLR) observations is the inability to accurately model all the forces acting on the satellite. Errors associated with the observations and the measurement model can detract from the estimates as well. These 'model errors' corrupt the solutions obtained from the satellite orbit determination process. Dynamical models for satellite motion utilize known geophysical parameters to mathematically detail the forces acting on the satellite. However, these parameters, while estimated as constants, vary over time. These temporal variations must be accounted for in some fashion to maintain meaningful solutions. The primary goal of this study is to analyze the feasibility of using a sequential process noise filter for estimating geodynamic parameters over time from the Laser Geodynamics Satellite (LAGEOS) SLR data. This evaluation is achieved by first simulating a sequence of realistic LAGEOS laser ranging observations. These observations are generated using models with known temporal variations in several geodynamic parameters (along track drag and the J(sub 2), J(sub 3), J(sub 4), and J(sub 5) geopotential coefficients). A standard (non-stochastic) filter and a stochastic process noise filter are then utilized to estimate the model parameters from the simulated observations. The standard non-stochastic filter estimates these parameters as constants over consecutive fixed time intervals. Thus, the resulting solutions contain constant estimates of parameters that vary in time which limits the temporal resolution and accuracy of the solution. The stochastic process noise filter estimates these parameters as correlated process noise variables. As a result, the stochastic process noise filter has the potential to estimate the temporal variations more accurately since the constraint of estimating the parameters as constants is eliminated. A comparison of the temporal resolution of solutions obtained from standard sequential filtering methods and process noise sequential filtering methods shows that the accuracy is significantly improved using process noise. The results show that the positional accuracy of the orbit is improved as well. The temporal resolution of the resulting solutions are detailed, and conclusions drawn about the results. Benefits and drawbacks of using process noise filtering in this type of scenario are also identified.

Hartman, Brian Davis↗
NASA NTRS2000

An Enhanced Multi-Objective Optimization Technique for Comprehensive Aerospace Design

An enhanced multiobjective formulation technique, capable of emphasizing specific objective functions during the optimization process, has been demonstrated on a complex multidisciplinary design application. The Kreisselmeier-Steinhauser (K-S) function approach, which has been used successfully in a variety of multiobjective optimization problems, has been modified using weight factors which enables the designer to emphasize specific design objectives during the optimization process. The technique has been implemented in two distinctively different problems. The first is a classical three bar truss problem and the second is a high-speed aircraft (a doubly swept wing-body configuration) application in which the multiobjective optimization procedure simultaneously minimizes the sonic boom and the drag-to-lift ratio (C(sub D)/C(sub L)) of the aircraft while maintaining the lift coefficient within prescribed limits. The results are compared with those of an equally weighted K-S multiobjective optimization. Results demonstrate the effectiveness of the enhanced multiobjective optimization procedure.

Chattopadhyay, Aditi↗
NASA NTRS2014

Experimental Investigation of a Flexible Wing with a Variable Camber Continuous Trailing Edge Flap Design

This paper presents experimental results of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization, tested at the University of Washington Aeronautical Labo- ratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10-scaled model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing, while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10 of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data indicate a high degree of data correlation and repeata- bility. The VCCTEF can achieve a drag reduction of up to 6.31 and an improvement in the lift-to-drag ratio (LD) of up to 4.85. The paper also presents two methods for estimating the lift coefficient of a rigid wing using a dynamic pressure correction and an aeroelastic deflection correction. Both methods provide good estimates of the rigid-wing lift coefficient.

Aerodynamics↗
NASA NTRS2021

Low Cost Access to Mars Surface using a Small Impact Lander

In order to reduce the cost of landing small payloads on Mars, a new technology is being developed: the Small High Impact Energy Landing Device concept (SHIELD). The purpose of SHIELD is to provide a low-cost option to deliver up to 6 kg of science payload to the surface of Mars. SHIELD could be launched as a hosted payload, rideshare on as a secondary payload adapter, or launching from a dedicated small launch vehicle using a kick stage to get to Mars. In order to enable delivery of low cost, SHIELD uses a large diameter deployed drag surface (> 2 m diameter) and low entry mass (< 50 kg) to achieve a very low ballistic coefficient (< 10 kg/m^2): this low ballistic coefficient results in low terminal velocity (< 70 m/sec) without requiring a parachute. Upon impacting the Martian surface at terminal velocity, SHIELD uses a mechanism to decelerate the payload to rest in a robust and predictable manner that limits acceleration of the payload to < 2000 g with a duration less than 8 milliseconds. The SHIELD concept payload subsystem includes a “ruggedized” small warm electronics box (WEB). The WEB houses the telecommunications, command and data handling, thermal control, electrical power, and payload subsystems while maintaining an internal operating temperature ranging between -20° to 20° C. The system is designed to survive the Martian night by utilizing electric heaters powered in a highly insulated box that is powered solar cells and secondary batteries. The WEB is designed to be impact resistant, capable of surviving an impact acceleration pulse equal to or less than 2000 g’s.

Woolley, Ryan↗
NASA NTRS1984

Wall mass transfer and pressure gradient effects on turbulent skin friction

The effects of mass injection and pressure gradients on the drag of surfaces were studied theoretically with the aid of boundary-layer and Navier-Stokes codes. The present investigation is concerned with the effects of spatially varying the injection in the case of flat-plate drag. Effects of suction and injection on wavy wall surfaces are also explored. Calculations were performed for 1.2 m long surfaces, one flat and the other sinusoidal with a wavelength of 30.5 cm. Attention is given to the study of the effect of various spatial blowing variations on flat-plate skin friction reduction, local skin friction coefficient calculated by finite difference boundary-layer code and Navier-Stokes code, and the effect of phase-shifting sinusoidal mass transfer on the drag of a sinusoidal surface.

Watson, R. D.↗
NASA NTRS1977

Subsonic and supersonic longitudinal stability and control characteristics of an aft-tail fighter configuration with cambered and uncambered wings and cambered fuselage

The longitudinal aerodynamic characteristics of a fighter airplane concept has been determined through an investigation over a Mach number range from 0.50 to 2.16. The configuration incorporates a cambered fuselage with a single external compression horizontal ramp inlet, a clipped arrow wing, twin horizontal tails, and a single vertical tail. The wing camber surface was optimized in drag due to lift and was designed to be self trimming at Mach 1.40 and at a lift coefficient of 0.20. The fuselage was cambered to preserve the design wing loadings on the part of the theoretical wing enclosed by the fuselage. An uncambered of flat wing of the same planform and thickness ratio distribution was also tested.

Dollyhigh, S. M.↗