Results for “Damage models” — Page 72

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRS1990

Creep and creep rupture of strongly reinforced metallic composites

A creep and creep damage theory is presented for metallic composites with strong fibers. Application is to reinforced structures in which the fiber orientation may vary throughout but a distinct fiber direction can be identified locally (local transverse isotropy). The creep deformation model follows earlier work and is based on a flow potential function that depends on invariants reflecting stress and the material symmetry. As the focus is on the interaction of creep and damage, primary creep is ignored. The creep rupture model is an extension of continuum damage mechanics and includes an isochronous damage function that depends on invariants specifying the local maximum transverse tension and the maximum longitudinal shear stress. It is posited that at high temperature and low stress, appropriate to engineering practice, these stress components damage the fiber/matrix interface through diffusion controlled void growth, eventually causing creep rupture. Experiments are outlined for characterizing a composite through creep rupture tests under transverse tension and longitudinal shear. Application is made to a thin-walled pressure vessel with reinforcing fibers at an arbitrary helical angle. The results illustrate the usefulness of the model as a means of achieving optimal designs of composite structures where creep and creep rupture are life limiting.

Robinson, D. N.↗

DOE OSTI2023

TOWARDS RAPID RESPONSE UPDATES OF POPULATIONS AT RISK

Understanding population at risks has been a focus of the LandScan program through its development of population estimates. With advancements in computer vision, deep learning technologies and access to High Performance Computing (HPC) and high resolution imagery, population estimates are now modeled at the building level. However, when those patterns are disrupted, rapid updates to population distribution estimates are needed to support humanitarian aid and response. Oak Ridge National Laboratory (ORNL) recently adapted an existing deep learning building footprint extraction model in development of a scalable approach to Building Damage Assessments (BDA). This new opportunity opens the possibility of automating BDA to support rapid population distribution estimate updates for geographic areas involved in geopolitical conflicts or natural events for humanitarian aid and response or where to focus recovery efforts. In addition, incorporate social surveys to further model human behavior under conflict or other scenarios that disrupt normal patterns of life.

Urban, Marie↗

DOE OSTI2022

Mechanistic modeling of lifetime distribution of SiC/SiC composite claddings

Silicon carbide (SiC) fiber-reinforced SiC matrix (SiC/SiC) composites have emerged as a new material candidate for fuel claddings in light water reactors. Recent studies showed that the load capacity of SiC/SiC materials exhibits a considerable statistical variation. Therefore, reliability analysis plays a critical role in design of SiC/SiC composite claddings. Here, this paper presents a probabilistic model for the lifetime distribution of SiC/SiC composites. The model is anchored by a multiaxial stress-based failure criterion and subcritical damage accumulation mechanism. Based on the kinetics of subcritical damage growth, the lifetime distribution of a laboratory test specimen for any given loading history can be calculated. A finite weakest-link model is used to extrapolate the lifetime distribution of test specimens to full-length claddings. It is shown that the damage accumulation mechanism has a strong influence on the lifetime distribution of the cladding. This finding highlights the importance of understanding the static fatigue behavior of SiC/SiC composites. The present analysis also demonstrates an intricate length effect on the failure probability of the cladding, which is expected to play a crucial role in design extrapolation.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Lunar BioSensor: An Autonomous Instrument to Study the Effects of the Lunar Environment on Biological Organisms

One of the major challenges to long-duration space travel and habitation in deep space is an in-depth understanding of the biological effects of space radiation, often convoluted by the impact of reduced gravity. Nonetheless, due to the near impossibility of simulating prolonged exposure to these combined effects in terrestrial facilities, actual missions are needed to characterize the radiobiological hazards of this environment. NASA Ames has been the leader in developing autonomous bio nanosatellites to address strategic knowledge gaps about the effects of space travel on biological organisms, including GeneSat, PharmaSat, EcAMSat, and BioSentinel. BioSentinel will be the first interplanetary bio nanosatellite or CubeSat to study the biological response to space radiation outside Low Earth Orbit (LEO). BioSentinel is an autonomous platform able to support biology and to investigate the effects of space radiation on a model organism in interplanetary deep space. It will fly onboard NASA’s Artemis-1, from which it will be deployed on a lunar fly-by trajectory and into a heliocentric orbit. The BioSentinel nanosatellite, a 6U deep space CubeSat (1U = 10-cm cube), will measure the DNA damage and response to ambient space radiation in a model biological organism, the budding yeast S. cerevisiae, which will be compared to information provided by an onboard physical radiation sensor and to data obtained in LEO (on the ISS) and on Earth. Even though the primary objective of the mission is to develop an autonomous spacecraft capable of conducting biological experiments in deep space, the 4U BioSensor science payload contained within the 6U free-flyer is an adaptable instrument platform that can perform biological measurements with different microorganisms and in multiple space environments, including the ISS, lunar gateway, and on the surface of the Moon. The proposed 4U instrument will leverage the payload design of the 6U free-flyer, utilizing the lunar lander or vehicle for power and data relay. Thus, nanosatellites like BioSentinel (and Lunar BioSensor) can be used to study the effects of both reduced gravity and space radiation and can house different bio organisms to answer specific science questions. In addition to their flexibility, nanosatellites also provide a low-cost alternative to more complex and larger missions, and require minimal crew support, if any.

space biosensors↗

DOE OSTI2021

In-Situ Calibrated Modeling of Residual Stresses Induced in Machining under Various Cooling and Lubricating Environments

Although many functional characteristics, such as fatigue life and damage resistance depend on residual stresses, there are currently no industrially viable ‘Digital Process Twin’ models (DPTs) capable of efficiently and quickly predicting machining-induced stresses. By leveraging advances in ultra-high-speed in-situ experimental characterization of machining and finishing processes under plane strain (orthogonal/2D) conditions, we have developed a set of physics-based semi-analytical models to predict residual stress evolution in light of the extreme gradients of stress, strain and temperature, which are unique to these thermo-mechanical processes. Initial validation trials of this novel paradigm were carried out in Ti-6Al4V and AISI 4340 alloy steel. A variety dry, cryogenically cooled and oil lubricated conditions were evaluated to determine the model’s ability to capture the tribological changes induced due to lubrication and cooling. The preliminarily calibrated and validated model exhibited an average correlation of better than 20% between the predicted stresses and experimental data, with calculation times of less than a second. Based on such fast-acting DPTs, the authors envision future capabilities in pro-active surface engineering of advanced structural components (e.g., turbine blades).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Storm surges and extreme sea levels: Review, establishment of model intercomparison and coordination of surge climate projection efforts (SurgeMIP).

Coastal flood damage is primarily the result of extreme sea levels. Climate change is expected to drive an increase in these extremes. While proper estimation of changes in storm surges is essential to estimate changes in extreme sea levels, there remains low confidence in future trends of surge contribution to extreme sea levels. Alerting local populations of imminent extreme sea levels is also critical to protecting coastal populations. Both predicting and projecting extreme sea levels require reliable numerical prediction systems. The SurgeMIP (surge model intercomparison) community has been established to tackle such challenges. Efforts to intercompare storm surge prediction systems and coordinate the community 's prediction and projection efforts are introduced. An overview of past and recent advances in storm surge science such as physical processes to consider and the recent development of global forecasting systems are briefly introduced. Selected historical events and drivers behind fast increasing service and knowledge requirements for emergency response to adaptation considerations are also discussed. The community 's initial plans and recent progress are introduced. These include the establishment of an intercomparison project, the identification of research and development gaps, and the introduction of efforts to coordinate projections that span multiple climate scenarios.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2006

Dynamic Crush Characterization of Ice

During the space shuttle return-to-flight preparations following the Columbia accident, finite element models were needed that could predict the threshold of critical damage to the orbiter's wing leading edge from ice debris impacts. Hence, an experimental program was initiated to provide crushing data from impacted ice for use in dynamic finite element material models. A high-speed drop tower was configured to capture force time histories of ice cylinders for impacts up to approximately 100 ft/s. At low velocity, the force-time history depended heavily on the internal crystalline structure of the ice. However, for velocities of 100 ft/s and above, the ice fractured on impact, behaved more like a fluid, and the subsequent force-time history curves were much less dependent on the internal crystalline structure.

Fasanella, Edwin L.↗

NASA NTRS2006

Test and Analysis Correlation of High Speed Impacts of Ice Cylinders

During the space shuttle return-to-flight preparations following the Columbia accident, finite element models were needed that could predict the threshold of critical damage to the orbiter s wing leading edge from ice debris impacts. Hence, an experimental program was initiated to provide crushing data from impacted ice for use in dynamic finite element material models. A high-speed drop tower was configured to capture force time-histories of ice cylinders for impacts up to approximately 100 ft/s. At low velocity, the force-time history depended heavily on the internal crystalline structure of the ice. However, for velocities of 100 ft/s and above, the ice fractured on impact, behaved more like a fluid, and the subsequent force-time history curves were much less dependent on the internal crystalline structure.

Fasanella, Edwin L.↗

DOE OSTI2024

Defect Production and Microstructural Feature Impact for Radiation Damage in Additively Manufactured 316 Stainless Steel

This milestone presents multi-scale modeling research results for additively manufactured 316 stainless steel. A combination of phase field, cluster dynamics, molecular dynamics, and density functional theory with machine learning is used, allowing for predictions of radiation-driven microstructural evolution in additively manufactured 316 stainless steel over a range of temperatures, damage rates, neutron spectra, and microstructures, and supporting the development of combined ion and neutron irradiation for material qualification. Informed by ion irradiation and neutron irradiation results across the Advanced Materials and Manufacturing Technologies program, we investigate the unique aspects of radiation-driven microstructure evolution in additively manufactured 316 stainless steel. In particular, we focus on understanding the impact of carbon concentration (varying, for example, between the 316L and 316H standards) on void formation; radiation-induced segregation at dislocation cells and grain boundaries; and the evolution of dislocation loops and network dislocation populations. We find that the unique characteristics of the additively manufactured microstructures must be accounted for in understanding the evolution of dislocation populations under thermal and irradiation conditions, such as the variation in sink strengths arising due to the variation in dislocation density. We also find that the radiation-induced segregation of Cr and Ni to grain boundaries and cell walls differs due to the differences in their defect sink biases. We also find that increasing the Ni content can slow vacancy diffusion, which may provide a mechanism for the observed reduction in transient swelling rate for austenitic Fe-Cr-Ni alloys with increasing Ni content. In addition, ion irradiations have shown that increasing carbon content in 316 SS results in a larger population of smaller voids, suggesting reduced vacancy diffusion. Our results show that the carbon content of additively manufactured 316 SS has a significant impact on the migration rate of defect clusters. The presence of carbon atoms results in carbon-vacancy trapping, significantly reducing the diffusion rate of vacancies. Carbon atoms may also be trapped near the surface of a void, which may reduce void growth by trapping vacancies that diffuse toward the void.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Salt Tank Testbed: a Test Site Designed to Replicate Floor Buckles Observed in Commercial TES Tanks

A test site has been designed and is under construction to replicate the buckling failure ob-served in several in-service storage tanks for nitrate salts operating up to 565°C. In commercial tanks multiple factors have been identified that influence the floors susceptibility to buck-ling, including: the as-manufactured shape of the floor, high compressive stresses due to thermal gradients and/or friction, fluid inventory and absolute temperature. Based on exten-sive modeling analysis it was determined that similar buckles can be reproduced in a scaled test tank (approximately 9x smaller than a representative commercial tank design). To buckle the scaled tank a radial thermal gradient is generated in the tank with a low fluid level, the fluid level is then increased while maintaining the thermal gradient; based on the modeling results just one of these cycles can plastically deform the tank floor. The test site which is under construction is designed to replicate this damaging cycle at lower temperatures. The goal of testing will be to reproduce this damaging cycle and buckle the scaled test tank floor, allowing proper model validation and a methodology for comparing different tank designs at a smaller (and less costly) scale.

25 ENERGY STORAGE↗

DOE OSTI2020

Mathematical Model of ATM Activation and Chromatin Relaxation by Ionizing Radiation

We propose a comprehensive mathematical model to study the dynamics of ionizing radiation induced Ataxia-telangiectasia mutated (ATM) activation that consists of ATM activation through dual mechanisms: the initiative activation pathway triggered by the DNA damage-induced local chromatin relaxation and the primary activation pathway consisting of a self-activation loop by interplay with chromatin relaxation. The model is expressed as a series of biochemical reactions, governed by a system of differential equations and analyzed by dynamical systems techniques. Radiation induced double strand breaks (DSBs) cause rapid local chromatin relaxation, which is independent of ATM but initiates ATM activation at damage sites. Key to the model description is how chromatin relaxation follows when active ATM phosphorylates KAP-1, which subsequently spreads throughout the chromatin and induces global chromatin relaxation. Additionally, the model describes how oxidative stress activation of ATM triggers a self-activation loop in which PP2A and ATF2 are released so that ATM can undergo autophosphorylation and acetylation for full activation in relaxed chromatin. In contrast, oxidative stress alone can partially activate ATM because phosphorylated ATM remains as a dimer. The model leads to predictions on ATM mediated responses to DSBs, oxidative stress, or both that can be tested by experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗

NASA NTRS1999

Parametric Study of Three-Stringer-Panel Compression-After-Impact Strength

Damage tolerance requirements for integrally-stiffened composite wing skins are typically met using design allowables generated by testing impact-damaged subcomponents, such as three-stringer stiffened panels. To improve these structures, it is necessary to evaluate the critical design parameters associated with three-stringer stiffened-panel compressive behavior. During recent research and development programs, four structural parameters were identified as sources for strength variation: (a) material system, (b) stringer configuration, (c) skin layup, and (d) form of axial reinforcement (tape versus pultruded carbon rods). Relative effects of these parameters on damage resistance and damage tolerance were evaluated numerically and experimentally. Material system and geometric configuration had the largest influence on damage resistance; location and extent of the damage zone influenced the sublaminate buckling behavior, failure initiation site, and compressive ultimate strength. A practical global-local modeling technique captured observed experimental behavior and has the potential to identify critical damage sites and estimate failure loads prior to testing. More careful consideration should be given to accurate simulation of boundary conditions in numerical and experimental studies.

Rousseau, Carl Q.↗

NASA NTRS2023

Damage Detection of a Pressure Vessel with Smart Sensing and Deep Learning

Structural Health Monitoring plays a crucial role in ensuring the safety and reliability of critical infrastructure, including pressure vessels involved in various applications. This research reports the damage detection of a pressure box employed in space habitat that operates in harsh environment where both structural failure and bolt joint loosening may occur. These failure modes are extremely hard to model based on first principles. We explore proper sensing mechanism and the associated inverse analysis algorithm that can elucidate the health condition of the pressure box. It is identified that piezoelectric impedance based active interrogation can provide necessary information for damage detection in such a system. Concurrently, deep learning technique leveraging spatial convolutional neural network is synthesized to analyze the raw data acquired and identify different types of damage. By training the deep learning model on a dataset of healthy and various damage scenarios, we can achieve high accuracy in identifying the presence of damage and its type. This research provides a data-driven methodology for structural damage detection using deep learning and has the potential to be extended to various systems with different failure modes.

Yang Zhang↗

DOE OSTI2020

Shaped Beams from Diamond Field-Emitter Array Cathodes

Diamond field-emitter arrays (DFEAs) are arrays of diamond pyramids with exquisitely sharp tips and micrometer-scale bases that produce high current densities. These arrays can be fabricated in arbitrary shapes, ranging from single tips to many millions of tips, so that they produce an inherently shaped electron beam. Each tip emits a modest current, but the large dense array can produce many Amps. We are investigating these cathodes for use in dielectric wakefield accelerators; however, they may also be applicable to vacuum microwave tubes. Recently, shaped beam production and transport have been demonstrated in the 1.3-GHz RF gun at the Argonne Cathode Test Stand at the Argonne National Laboratory. The charge was measured on a Faraday cup and the beam imaged on a YAG screen with peak electric field gradients on the cathode ranging from 12 to 35 MV/m. Three cathode geometries were tested: one 1-mm equilateral triangle with 7-mu m base pyramids and 10-mu m pitch, one 1-mm equilateral triangle with 10-mu m base and 25-mu m pitch, and one sparse 5 x 5 square array with 20-mu m base and 400-mu m pitch. The two triangular arrays emitted 35 nC in an RF macropulse at 35 MV/m and 13-nC charge at 27 MV/m, respectively, while the sparse array emitted 0.060-nC charge at 15 MV/m. This article presents the results of the triangular array experiments, including damage due to breakdown in the RF gun and initial models of tip-to-tip shielding.

Cathodes↗