Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIGESTIVE SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

MOSAiC-Colorado State University Ice Spectrometer

This data set contains atmospheric ice nucleating particle (INP) measurements, using Colorado State University&rsquo;s (CSU) Ice Spectrometer (IS), of filter collections taken at the U.S. DOE ARM AMF2 site onboard the R/V Polarstern P-deck during the Multidisciplinary Drifting Observatory for the Study of Arctic Climate (MOSAiC) field campaign. Samples were collected from October 27, 2019 to September 24, 2020. A filter sampler was mounted approximately 15 m above ground level on a railing in proximity to (and approximately 3 m below) the Aerosol Observation System (AOS) inlet. Single-use filter units open to the atmosphere were pre-cleaned and pre-loaded with 47-mm diameter Nuclepore polycarbonate (0.2 &micro;m pore-diameter) filters. Filters were typically drawn for a three-day period, with an average volume of air filtered of 87,000 standard liters. Total volumes were calculated through recorded daily flow rates using a mass flow meter (TSI). After collection, filters were stored and transported frozen until analysis using CSU&rsquo;s IS instrument (McCluskey et al., 2018). Aerosol particles were first re-suspended in 8 mL of 0.1 &micro;m-filtered deionized (DI) water. Aliquots of each suspension, and corresponding 11-fold dilutions, were dispensed into polymerase chain reaction (PCR) trays and placed into the aluminum blocks of the IS. Samples were cooled at approximately 0.33 &deg;C min -1 and freezing detected optically with corresponding temperatures recorded. Cumulative INP concentrations were determined through calculating the number of INPs per mL of suspension (Vali, 1971) and converting to concentration per standard L of air by accounting for the proportion of liquid used and volume of air collected. All samples were corrected for the number of INPs on the average of four field blanks (cleaned, handled, transported, and analyzed in the same way without air flow). Two-tailed, 95% confidence intervals for binomial sampling are provided (Agresti and Coull, 1998). Select samples were also heat treated (95 &deg;C for 20 min) to denature and deactivate biological INPs present and digested in 10% H 2 O 2 at 95 &deg;C under UV-B for 20 min to remove any organic carbon INPs. Agresti, A, and BA Coull. 1998. "Approximate is better than &ldquo;exact&rdquo; for interval estimation of binomial proportions." American Statistics 52: 119&ndash;126. https://doi.org/10.2307/2685469 McCluskey, CS, J Ovadnevaite, M Rinaldi, J Atkinson, F Belosi, D Ceburnis, &hellip; and PJ DeMott. 2018. "Marine and Terrestrial Organic Ice-Nucleating Particles in Pristine Marine to Continentally Influenced Northeast Atlantic Air Masses." Journal of Geophysical Research: Atmospheres 123 (11): 6196&ndash;6212, https://doi.org/10.1029/2017JD028033 Vali, G. 1971. "Quantitative Evaluation of Experimental Results and the Heterogeneous Freezing Nucleation of Supercooled Liquids." Journal of the Atmospheric Sciences 28: 402-209. https://doi.org/10.1175/1520-0469(1971)028<0402:QEOERA>2.0.CO;2

54 ENVIRONMENTAL SCIENCES↗

Baylor University Campus-Wide Deep Dive

In January 2020, staff members from the Engagement and Performance Operations Center (EPOC) and the Lonestar Education And Research Network (LEARN) met with researchers and staff at Baylor University for the purpose of a Campus-Wide Deep Dive into research drivers. The goal of this meeting was to help characterize the requirements for five campus research use cases and to enable cyberinfrastructure support staff to better understand the needs of the researchers they support. Profiled scientific use cases included: - Experimental High Energy Physics (HEP) - Proton Computed Tomography (pCT) - Nutrition and Relation to Digestive Microbiome - Baylor University Core Research Facilities - Molecular Quantum-dot Cellular Automata (QCA), and Material Science of Quantum Computing - Modeling and Simulation of Low-Dimensional and Nano-Structured Materials - Computational Fluid Dynamics Material for this event included the written documentation from each of the research areas at Baylor University, documentation about the current state of technology support, and a write-up of the discussion that took place in person. The Case Studies highlighted the ongoing challenges that Baylor University has in supporting a cross-section of established and emerging research use cases. Each Case Study mentioned unique challenges which were summarized into common needs. These included: - Tradeoffs for network/software security, and usability of the resulting infrastructure. Better communication to set expectations and understand realities is required. - Computation use on campus is widespread and healthy. While no major problems were uncovered, upgrades to maintain current usage patterns and encourage growth will be required. - Storage is a critical need for enterprise use cases and research. In particular, a campus wide ‘storage architecture’ to support research use cases (e.g. instruments, data sharing) is required in the 2-5 year time window. - Instrumentation on campus is healthy and expanding. Technology must scale with this in the form of computation and storage. - Working with LEARN to upgrade network capacity (in multiples of 10G, or upgrades to 100G) will be required in the 1-3 year time frame. - Network monitoring and visibility will help to establish external science use cases. - Data sharing via portal systems is not currently a critical need, but growing in scope. EPOC can assist Baylor with options.

99 GENERAL AND MISCELLANEOUS↗

US-India Consortium for Development of Sustainable Advanced Lignocellulosic Biofuel Systems

This multi-institutional project had as it main objectives to develop a fully integrated platform for the production of advanced biofuels, specifically butanol, from sustainably produced switchgrass and biomass sorghum and to develop economic models that could guide the establishment of a crop to fuel value chain. The project was organized into three work packages: (1) WP1 Feedstock Development and Supply. Activities in this WP resulted in the development of improved biomass sorghum cultivars and biomass hybrids that generate high yields of biomass with limited inputs of water, fertilizer and agri-chemicals and that display less recalcitrance to enzymatic saccharification at the biorefinery; the identification of physiological responses and genes associated with sorghum’s tolerance to water logging as the basis for the development of biomass sorghums that can be cultivated on land prone to flooding; the identification of water-logging tolerant switchgrass genotypes among existing germplasm; the identification of management practices that maximize switchgrass biomass yield (fertilizer applications, harvest regimens) on commercial farms on different types of soil in Missouri. (2) WP2 Biorefinery Technologies. This WP included the development of a recombinant E. coli strain able to convert fermentable sugars derived from biomass sorghum and switchgrass to butyrate as a precursor for the advanced biofuel butanol. Butanol is toxic to most microbes, so that yields tend to be low. In contrast, butyrate can be produced in high titer and high yield by several naturally occurring bacteria, but these species are strictly anaerobic, which complicates commercial production. Our strategy involved developing a recombinant strain of E. coli able to produce high yields and high titers of butyrate. The butyrate can then be reduced to butanol via chemical conversion. In addition, a techno-economic analysis of converting sorghum and switchgrass biomass to ethanol was conducted based on data obtained at a pilot biorefinery. These data combined with small-scale butanol production data were used as the basis for a techno-economic analysis of biomass-to-butanol conversion. Furthermore, the biorefinery stillage was evaluated as a source of fertilizer or soil amendment. In contrast to the use of biochar as a soil amendment, stillage resulted in enhanced microbial activity in the soil and release of CO2. Stillage was determined to be a suitable feedstock for biogas production in an anaerobic digester. Biorefinery lignin can be blended with polymers to create novel UV-resistant materials promising for application in outer space, and as a source of organic acids for use in plastics. These applications offer opportunities to create value from the biorefinery residues. (3) WP3. This WP focused on development of economic models that can help define the most successful strategy for implementing biofuel production from bioenergy crops. Southeastern Missouri was determined to be the best location for a bio-butanol facility that processes biomass crops, due to the abundance of feedstock within a small radius of the facility. The most effective transportation method is by rail car. Feedstock availability was considered a more important driver for commercial success than the availability of a butanol market. The average cost of producing switchgrass biomass was calculated to be $65/ton assuming a biomass yield of 8 tons per hectare (the upper end of the yield in the commercial trials in WP2). Lower yields drive up costs, but improved genotypes will conversely reduce costs. Based on farmer surveys, conducting university extension activities was determined to positively influence farmers’ willingness to consider switchgrass. Other factors included experience with pasture land and forest land, and the availability of policies that provide a safety net to the farmers in case of instability in the biofuels market. This instability can be mitigated in part by ensuring adequate biomass supplies through diversification. The project supported the training of 20 graduate students and resulted in 57 peer-reviewed journal articles (with eight additional in review or in progress), eight book chapters and five patents.

09 BIOMASS FUELS↗

Radiocurability by Targeting Tumor Necrosis Factor-{alpha} Using a Bispecific Antibody in Carcinoembryonic Antigen Transgenic Mice

Purpose: Tumor necrosis factor-{alpha} (TNF-{alpha}) enhances radiotherapy (RT) killing of tumor cells in vitro and in vivo. To overcome systemic side effects, we used a bispecific antibody (BsAb) directed against carcinoembryonic antigen (CEA) and TNF-{alpha} to target this cytokine in a CEA-expressing colon carcinoma. We report the evaluation of this strategy in immunocompetent CEA-transgenic mice. Methods and Materials: The murine CEA-transfected colon carcinoma MC-38 was used for all experiments. In vitro, clonogenic assays were performed after RT alone, TNF-{alpha} alone, and RT plus TNF-{alpha}. In vivo, the mice were randomly assigned to treatment groups: control, TNF-{alpha}, BsAb, BsAb plus TNF-{alpha}, RT, RT plus TNF-{alpha}, and RT plus BsAb plus TNF-{alpha}. Measurements of endogenous TNF-{alpha} mRNA levels and evaluation of necrosis (histologic evaluation) were assessed per treatment group. Results: In vitro, combined RT plus TNF-{alpha} resulted in a significant decrease in the survival fraction at 2 Gy compared with RT alone (p < 0.00001). In vivo, we observed a complete response in 5 (50%) of 10, 2 (20%) of 10, 2 (18.2%) of 11, and 0 (0%) of 12 treated mice in the RT plus BsAb plus TNF-{alpha}, RT plus TNF-{alpha}, RT alone, and control groups, respectively. This difference was statistically significant when TNF-{alpha} was targeted with the BsAb (p = 0.03). The addition of exogenous TNF-{alpha} to RT significantly increased the endogenous TNF-{alpha} mRNA level, particularly when TNF-{alpha} was targeted with BsAb (p < 0.01). The percentages of necrotic area were significantly augmented in the RT plus BsAb plus TNF-{alpha} group. Conclusion: These results suggest that targeting TNF-{alpha} with the BsAb provokes RT curability in a CEA-expressing digestive tumor syngenic model and could be considered as a solid rationale for clinical trials.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

San Francisco Biofuel Program: Brown Grease to Biodiesel Demonstration (Project Report)

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the program by other municipal agencies (as applicable). In order to accomplish the goals of the project, the following steps were performed: 1. Operation of a demonstration facility designed to receive 10,000 to 12,000 gallons of raw Trap Waste each day from private Trap Waste hauling companies. The demonstration facility was designed and built by Pacific Biodiesel Technologies (PBTech). The demonstration facility would also recover 300 gallons of Brown Grease per day from the raw Trap Waste. The recovered Brown Grease was expected to contain no more than 2% Moisture, Insolubles, and Unsaponifiables (MIU) combined. 2. Co-digestion of the side streams (generated during the recovery of 300 gallons of Brown Grease from the raw Trap Waste) with wastewater sludge in the WWTP's anaerobic digesters. The effects of the side streams on anaerobic digestion were quantified by comparison with baseline data. 3. Production of 240 gallons per day of ASTM D6751-S15 grade Biodiesel fuel via a Biodiesel conversion demonstration facility, with the use of recovered Brown Grease as a feedstock. The demonstration facility was designed and built by Blackgold Biofuels (BGB). Side streams from this process were also co-digested with wastewater sludge. Bench-scale anaerobic digestion testing was conducted on side streams from both demonstration facilities to determine potential toxicity and/or changes in biogas production in the WWTP anaerobic digester. While there is a lot of theoretical data available on the lab-scale production of Biodiesel from grease Trap Waste, this full-scale demonstration project was one of the first of its kind in the United States. The project's environmental impacts were expected to include: Reduction of greenhouse gas emissions by prevention of the release of methane at landfills. Although the combustion product of Biodiesel and Methane gas produced in the Anaerobic digester, Carbon Dioxide, is also a greenhouse gas; it is 20 times weaker for the same amount (per mole) released, making its discharge preferable to that of Methane. The use of Biodiesel in place of fossil-fuel derived Diesel was expected to reduce net Carbon Dioxide, Ash Particulate, Sulfate, Silicate, and Soot emissions, thereby improving air quality.

09 BIOMASS FUELS↗

CACTI ARM Aerial Facility Measurements of Ice Nucleating Particles

The dataset comprises measures, using Colorado State University's Ice Spectrometer (IS, an immersion freezing device with a range from 0&deg;C down to -26 to -29&deg;C) of atmospheric ice nucleating particle (INP) concentrations taken on the Atmospheric Radiation Measurement (ARM) program Aerial Facilty (AAF) G-1 aircraft. INP measurements on the G-1 were collected from varied altitudes on different flights over the region of the Sierras de C&oacute;rdoba mountain range of north-central Argentina, centred over ARM's Mobile Facility (AMF-1) near Villa Yacanto, where ground-based INP measures were being taken concurrently. Both studies took place as part of the Cloud, Aerosol, and Complex Terrain Interactions (CACTI) Experiment. A filter sampling system was deployed on the G-1 to collect aerosol particles for post-processing of INPs collected on filters (measuring their immersion freezing ability) once returned to Colorado State University (CSU). Filter holders used were pre-cleaned aluminum in-line units loaded with pre-cleaned and pre-sterilized 47 mm dia. Nuclepore polycarbonate filters (0.2 mm pore size). Filters were drawn for varied times, resulting in varied volumes collected (51 to 1667 SL). Mass flow rate was recorded in real-time so that total sampled volume (at standard temperature and pressure) could be determined. A total of 34 sample filters were collected over the IOP, including 5 blanks. Filters were stored at -20&deg;C freezer prior to frozen return to Colorado State University (CSU). . Processing to obtain spectra of INP number concentration active via the immersion freezing mechanism versus temperature was conducted using CSU's IS instrument (McCluskey et al., 2018). For measurment of INPs, collected aerosol particles were re-suspended in 7 mL of 0.02 &micro;m-filtered deionized water. Aliquots of each suspension, and serial dilutions, were dispensed into trays which were fit into aluminum blocks in the IS. Samples are cooled at 0.33&deg;C min-1 and the freezing temperatures of wells recorded automatically. Cumulative INP concentrations were determined by first calculating the INPs per mL of suspension based on Vali (1971) and then converting to concentration per standard liter of air using the proportion of the total liquid sample dispensed and the air sample volumes. Aliquots of suspensions from selected samples were also heat treated (95&deg;C for 20 min) to denature and deactivate biological INPs, and digested in 10% H2O2 at 95&deg;C under UV-B to remove all organic carbon INPs. McCluskey, C. S., J. Ovadnevaite, M. Rinaldi, J. Atkinson, F. Belosi, D. Ceburnis, S. Marullo, T. C. J. Hill, U. Lohmann, Z. A. Kanji, C. O&rsquo;Dowd, S. M. Kreidenweis, P. J. DeMott, 2018: Marine and Terrestrial Organic Ice Nucleating Particles in Pristine Marine to Continentally-Influenced Northeast Atlantic Air Masses, Journal of Geophysical Research: Atmospheres, 123, 6196&ndash;6212, https://doi.org/10.1029/2017JD028033. Vali, G., 1971: Quantitative evaluation of experimental results on the heterogeneous freezing nucleation of supercooled liquids. J. Atmos. Sci., 28, 402&ndash;409.

54 ENVIRONMENTAL SCIENCES↗

Algae to HEFA : Economics and potential deployment in the United States

Abstract To reach the goals set by the US Department of Energy's Sustainable Aviation Fuel (SAF) Grand Challenge, currently available feedstocks may be insufficient. Giving priority to developing, prototyping and reducing the cost of algal feedstock before investing and lining up locations is important. As the production of algal feedstocks advances, a simplified conversion approach using more mature technologies can help reduce the investment risk for algae‐based fuels. Reducing process complexity to the steps described here [namely, conversion of lipids to HEFA (hydroprocessed esters and fatty acids) fuels and relegating the remainder of the biomass to anaerobic digestion or food/feed production] enables the near‐term production of algal SAF but presents challenging economics depending on achievable cultivation costs and compositional quality. However, these economics can be improved by present‐day policy incentives. With these incentives, the modeled algae‐to‐HEFA pathway could reach a minimum fuel selling price as low as $4.7 per gasoline gallon equivalent depending on the carbon intensity reduction that can be achieved compared with petroleum. Uncertainty about algal feedstock production maturity in the current state of technology and the future will play a large role in determining the economic feasibility of building algae‐to‐HEFA facilities. For example, if immaturity increases the feedstock price by even 10%, SAF production in 2050 is about 58% of the production which could have been achieved with mature feedstock. Additionally, growth in this conversion pathway can be notably boosted through the inclusion of subsidies, and also through higher‐value coproducts or higher lipid yields beyond the scope of the process considered here.

09 BIOMASS FUELS↗

Monitoring of microbial communities in anaerobic digestion sludge for biogas optimisation

Highlights: • Characterisation of microbial communities by cloning, pyrosequencing and T-RFLP. • T-RFLP is most suitable as monitoring method but lacks taxonomic information. • Existing in silico tools unable to identify T-RFs in T-RFLP analysis of AD sludge. • This study developed a combined approach to assign taxonomy to database of T-RFs. • Combined approach is a reliable and economical way to monitor microbial consortia. - Abstract: This study characterised and compared the microbial communities of anaerobic digestion (AD) sludge using three different methods – (1) Clone library; (2) Pyrosequencing; and (3) Terminal restriction fragment length polymorphism (T-RFLP). Although high-throughput sequencing techniques are becoming increasingly popular and affordable, the reliance of such techniques for frequent monitoring of microbial communities may be a financial burden for some. Furthermore, the depth of microbial analysis revealed by high-throughput sequencing may not be required for monitoring purposes. This study aims to develop a rapid, reliable and economical approach for the monitoring of microbial communities in AD sludge. A combined approach where genetic information of sequences from clone library was used to assign phylogeny to T-RFs determined experimentally was developed in this study. In order to assess the effectiveness of the combined approach, microbial communities determined by the combined approach was compared to that characterised by pyrosequencing. Results showed that both pyrosequencing and clone library methods determined the dominant bacteria phyla to be Proteobacteria, Firmicutes, Bacteroidetes, and Thermotogae. Both methods also found that sludge A and B were predominantly dominated by acetogenic methanogens followed by hydrogenotrophic methanogens. The number of OTUs detected by T-RFLP was significantly lesser than that detected by the clone library. In this study, T-RFLP analysis identified majority of the dominant species of the archaeal consortia. However, many of the more highly diverse bacteria consortia were missed. Nevertheless, the combined approach developed in this study where clone sequences from the clone library were used to assign phylogeny to T-RFs determined experimentally managed to accurately predict the same dominant microbial groups for both sludge A and sludge B, as compared to the pyrosequencing results. Results showed that the combined approach of clone library and T-RFLP accurately predicted the dominant microbial groups and thus is a reliable and more economical way to monitor the evolution of microbial systems in AD sludge.

09 BIOMASS FUELS↗

Progress on Plant-Level Components for Nuclear Fuel Recycling: Commonality

Progress made in developing a common mathematical modeling framework for plant-level components of a simulation toolkit for nuclear fuel recycling is summarized. This ongoing work is performed under the DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, which has an element focusing on safeguards and separations (SafeSeps). One goal of this element is to develop a modeling and simulation toolkit for used nuclear fuel recycling. The primary function of the SafeSeps simulation toolkit is to enable the time-dependent coupling of separation modules and safeguards tools (either native or third-party supplied) that simulate and/or monitor the individual separation processes in a separations plant. The toolkit integration environment will offer an interface for the modules to register in the toolkit domain based on the commonality of diverse unit operations. This report discusses the source of this commonality from a combined mathematical modeling and software design perspectives, and it defines the initial basic concepts needed for development of application modules and their integrated form, that is, an application software. A unifying mathematical theory of chemical thermomechanical network transport for physicochemical systems is proposed and outlined as the basis for developing advanced modules. A program for developing this theory from the underlying first-principles continuum thermomechanics will be needed in future developments; accomplishment of this task will enable the development of a modern modeling approach for plant-level models. Rigorous, advanced modeling approaches at the plant-level can only proceed from the development of reduced (or low-order) models based on a solid continuum field theory foundation. Such development will pave the way for future programmatic activities on software verification, simulation validation, and model uncertainty quantification on a scientific basis; currently, no satisfactory foundation exists for considering these activities. The exploitation of mathematical commonality for unit operations with the intent of developing generic and comprehensive software for nuclear reprocessing has not been considered to this author's knowledge. Past attention has been given to plant-level processes on an individual and isolated basis, which has led to various models and corresponding codes implementing non-systematic approaches based on elementary principles of chemical processing. This practice has built an initial knowledge base, but it was not fruitful in producing a lasting and extensible simulation capability. In contrast, a common, rigorous, mathematical modeling framework for all plant-level operations, as proposed here, has a tremendous practical and theoretical value because it will reduce the software implementation work, creates a well-defined modeling standard to compare past and future models, and, more importantly, opens the doors for scientific considerations of simulation fidelity; the latter has an obvious beneficial impact in supporting experimental validation programs. Therefore, the proposed framework is likely to generate a solid foundation for modeling plant-level processes for physicochemical nuclear (and non-nuclear) applications. Demonstration of concrete module implementation is the subject of future communications including prototypes for several modules, namely, voloxidation, dissolver, digester, accountability tank, and solvent extraction. Unit-operation commonality is a key aspect to be explored for a successful implementation of these modules aimed at realizing various flowsheets and plant configurations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improving the Economic Viability of Biological Utilization of Coal Power Plant CO 2 by Improved Algae Productivity and Integration with Wastewater Treatment

The overall goal of this project was to improve the cost-effectiveness of systems using algae to capture and beneficially utilize CO 2 from the flue gas of coal-fired power plants. Algal biomass cultivation is an attractive alternative for carbon capture and utilization because it can uptake more CO 2 per land area than any other photosynthetic crop. Also, the resulting biomass can be used to make valuable large-market commodity products, such as biofuels and animal feed. However, the use of algal carbon capture has been limited by several factors including: (1) high costs for growing algae (>$\$1,300$/ton), (2) large land requirements for algae cultivation, and (3) environmental concerns about the large amount of water and nutrient inputs needed for growing algae. This project has taken direct aim at resolving these key limitations and demonstrated several viable approaches to improve the economic and environmental feasibility of algal carbon capture. In particular, this project demonstrated a significant increase in average annual algal productivity from baseline values of 8 g/m 2 -day to above 20 g/m 2 -day. This supports a much lower projected cost of algae production (<$\$500$/ton) and reduces land requirements by more than 50%. Additionally, this project confirmed the ability to grow multiple algae species with wastewater nutrients, which facilitates the potential for substantial new revenue streams for algae cultivation based on tipping fees for nutrient laden wastewater. This study highlighted that there is more potential value in wastewater nutrient treatment credits than in the primary commodity products made from algae. The use of wastewater inputs also mitigates the concerns associated with the large amount of water needed for growing algae. The algal biomass grown for this project using wastewater and simulated flue gas inputs were characterized for potential use as an animal feed ingredient. The algae had a protein content in the range of 35-40%, which is between some common commodity animal feed products— distiller’s grains (~25-30% protein) and soybean meal (45-50% protein). In-vitro digestion tests using cattle rumen fluids, showed that this algae biomass was best suited for use as “bypass protein”, which is digested in the animal intestine. Based on the protein content and amino acid profile of the algae grown in this study, it was estimated to have market value in the range of $\$190$-$\$280$/ton. There is potential for higher value feed products if the algae content of omega-3 fatty acids or antioxidants is accounted for. This project also did small scale demonstration of forward osmosis algae dewatering and nanofiltration of hydrothermal liquefaction aqueous products, which were shown to improve the cost and energy balance for producing algal products. When all the improvements demonstrated in this study were included in techno-economic analysis, it showed there was a viable pathway to profitable algal CO 2 utilization with a payback period in the range of six to ten years.

01 COAL, LIGNITE, AND PEAT↗

Storage-Induced Collapse of Lignin Macromolecular Structure and Its Impacts on the Biorefinery

Lignin plays a vital role in the economics of biorefineries, serving as a source of process energy and a feedstock for sustainable fuels and chemical production. While understanding lignin’s chemical composition is crucial, emerging evidence suggests that a more comprehensive understanding of its macromolecular structure is critical to explaining its complex behavior in the biorefinery. This study investigated the partial collapse of the lignin network in corn stover feedstock after harvest and storage as a result of the microbial digestion of hemicellulose. Fluorescence microscopy was used to detect the collapse of lignin in terms of lignin’s inter-molecular interaction and the re-orientation of lignin’s chromophores, by the changes in lignin’s fluorescence lifetime, anisotropy, and the number of effective emitters. With minimal sample perturbation, our in-situ microscopic results revealed lignin's coil-globule transition phenomena, which was only previously predicted by molecular dynamics modeling extracted lignin in solvent. This collapse of lignin macromolecular structure was confirmed by results from NMR, IR, Raman, and powder X-ray diffraction. We also investigated the impact of this storage-induced collapse on the downstream biorefinery processes. Our study revealed that the two major approaches for lignin valorization in the lignin-first biorefinery model, namely monomer extraction and milled wood lignin extraction, were negatively impacted by the lignin collapse. As changes during storage are a source of feedstock variability, our study highlights the importance of understanding the effect of feedstock handling on biorefinery operations and economics.

09 BIOMASS FUELS↗

2020 Exascale Computing Project Annual Meeting (Executive Summary Report)

The Exascale Computing Project (ECP) delivers specific applications, software products, and outcomes on DOE computing facilities. Integration across these elements for specific hardware technologies for exascale system instantiations is fundamental to ECP success. The outcome of the ECP is the delivery of a capable exascale computing ecosystem to provide breakthrough solutions addressing our most critical challenges in scientific discovery, energy assurance, economic competitiveness, and national security. This outcome is not a matter of ensuring more powerful computing systems. The ECP is designed to create more valuable and rapid insights from a wide variety of applications (“capable”), which requires a much higher level of inherent efficacy in all methods, software tools, and ECP-enabled computing technologies to be acquired by DOE laboratories (“ecosystem”). The ECP annual meeting provides a unique opportunity for the core technical expertise in the United States focused on achieving this next plateau of computational science and computing performance to engage in direct discussions on project execution. Face-to-face gatherings in technical communities like this are common and needed for the exchange of scientific ideas and technical performance. The ECP annual meeting stands apart from other technical conferences and meetings in the computing community as it is uniquely and solely focused on the execution of the ECP and the integration of technical activities leading to the creation of the exascale computing ecosystem for the future. The direct interaction of key critical technical staff, who are leaders in their respective fields, and the resulting give-and-take between software, applications, and hardware and the technical co-design therein, is unique and essential to the effective execution of the ECP. The first annual meeting was held in Knoxville, Tennessee, January 31 – February 2, 2017 and brought together, for the first time, a diverse collection of researchers from 16 DOE national laboratories as well as university computer and computational science researchers to discuss shared problems and joint solutions for the development of a capable exascale computing ecosystem. These interactions resulted in focused technical plans and an energized community centered on advances for ECP. The second annual meeting was held in Knoxville, Tennessee, February 5–9, 2018. It included 643 individual thought leaders and performers in application development, software research and deployment, and hardware research and integrators, all of whom are part of the multifaceted, billion dollar HPC community. This meeting provided a platform to discuss and disseminate numerous examples where researchers with common goals and synergistic solutions came together for the first time to deliver tangible results. Additionally, at the 2018 meeting, ECP researchers had the opportunity to digest all US HPC vendor R&D product roadmaps pointing to exascale – not only to learn how their research can play a role, but, more importantly, to influence those roadmaps to ensure successful delivery on DOE applications that will contribute to (if not solve) problems of national interest in national security, science, energy, and health, as well as growing security threats. The third annual meeting was held in Houston, Texas, January 14–17, 2019. With a 19% increase in the number of registrations (768 people), and the change in location, the third annual meeting was considered the most impactful of the three at the time. The new website provided a better platform for the dissemination of the content, the new venue as a meeting hotel instead of a conference center facilitated interactions and discussions after event hours, and the addition of an award-winning mobile event conference app (Whova) transformed dramatically the attendee experience at the event. This fourth annual meeting was held in Houston, Texas, February 3-7, 2020. This meeting had an increase in the number of attendees for a total of 824 people registered (782 attendees) and included numerous enhancements based on feedback and lessons learned from previous meetings, some of which are listed here: Improved quality of the sessions, their material and the whole program.; Had more industry participation and addition of external collaborators from overseas.; Published the full agenda earlier to better accommodate attendance and travel plans based on schedule.; Centralized all sessions in one venue.; Provided additional hotels and room blocks for the attendees.; Improved communication with the audience (links, material, directions, notifications, etc.) to go paperless.; Enhanced side meeting scheduling, management and user experience.; Made available additional space and tables for impromptu meetings and side discussions.; Improved IT and A/V solutions for speakers. In addition, our final survey captured the following points as opportunities for improvement in future meetings: consider a different meeting location that is more pedestrian friendly, reduce talks during working meals to allow more collaboration and informal time, adapt the agenda to acknowledge attendees from different timezones, consider recording some of the tutorials and/or sessions to share broadly with the HPC community, have a larger poster room, provide additional power strips, and improve the WiFi.

97 MATHEMATICS AND COMPUTING↗

Methane emissions from MBT landfills

Highlights: • Compilation of methane generation potential of mechanical biological treated (MBT) municipal solid waste. • Impacts and kinetics of landfill gas production of MBT landfills, approach with differentiated half-lives. • Methane oxidation in the waste itself and in soil covers. • Estimation of methane emissions from MBT landfills in Germany. - Abstract: Within the scope of an investigation for the German Federal Environment Agency (“Umweltbundesamt”), the basics for the estimation of the methane emissions from the landfilling of mechanically and biologically treated waste (MBT) were developed. For this purpose, topical research including monitoring results regarding the gas balance at MBT landfills was evaluated. For waste treated to the required German standards, a methane formation potential of approximately 18–24 m{sup 3} CH{sub 4}/t of total dry solids may be expected. Monitoring results from MBT landfills show that a three-phase model with differentiated half-lives describes the degradation kinetics in the best way. This is due to the fact that during the first years of disposal, the anaerobic degradation processes still proceed relatively intensively. In addition in the long term (decades), a residual gas production at a low level is still to be expected. Most of the soils used in recultivation layer systems at German landfills show a relatively high methane oxidation capacity up to 5 l CH{sub 4}/(m{sup 2} h). However, measurements at MBT disposal sites indicate that the majority of the landfill gas (in particular at non-covered areas), leaves the landfill body via preferred gas emission zones (hot spots) without significant methane oxidation. Therefore, rather low methane oxidation factors are recommended for open and temporarily covered MBT landfills. Higher methane oxidation rates can be achieved when the soil/recultivation layer is adequately designed and operated. Based on the elaborated default values, the First Order Decay (FOD) model of the IPCC Guidelines for National Greenhouse Gas Inventories, 2006, was used to estimate the methane emissions from MBT landfills. Due to the calculation made by the authors emissions in the range of 60,000–135,000 t CO{sub 2-eq.}/a for all German MBT landfills can be expected. This wide range shows the uncertainties when the here used procedure and the limited available data are applied. It is therefore necessary to generate more data in the future in order to calculate more precise methane emission rates from MBT landfills. This is important for the overall calculation of the climate gas production in Germany which is required once a year by the German Government.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

TANK 4 CHARACTERIZATION, SETTLING, AND WASHING STUDIES

A sample of PUREX sludge from Tank 4 was characterized, and subsequently combined with a Tank 51 sample (Tank 51-E1) received following Al dissolution, but prior to a supernate decant by the Tank Farm, to perform a settling and washing study to support Sludge Batch 6 preparation. The sludge source for the majority of the Tank 51-E1 sample is Tank 12 HM sludge. The Tank 51-E1 sample was decanted by SRNL prior to use in the settling and washing study. The Tank 4 sample was analyzed for chemical composition including noble metals. The characterization of the Tank 51-E1 sample, used here in combination with the Tank 4 sample, was reported previously. SRNL analyses on Tank 4 were requested by Liquid Waste Engineering (LWE) via Technical Task Request (TTR) HLE-TTR-2009-103. The sample preparation work is governed by Task Technical and Quality Assurance Plan (TTQAP), and analyses were controlled by an Analytical Study Plan and modifications received via customer communications. Additional scope included a request for a settling study of decanted Tank 51-E1 and a blend of decanted Tank 51-E1 and Tank 4, as well as a washing study to look into the fate of undissolved sulfur observed during the Tank 4 characterization. The chemistry of the Tank 4 sample was modeled with OLI Systems, Inc. StreamAnalyzer to determine the likelihood that sulfate could exist in this sample as insoluble Burkeite (2Na{sub 2}SO{sub 4} {center_dot} Na{sub 2}CO{sub 3}). The OLI model was also used to predict the composition of the blended tank materials for the washing study. The following conclusions were drawn from the Tank 4 analytical results reported here: (1) Any projected blend of Tank 4 and the current Tank 51 contents will produce a SB6 composition that is lower in Ca and U than the current SB5 composition being processed by DWPF. (2) Unwashed Tank 4 has a relatively large initial S concentration of 3.68 wt% on a total solids basis, and approximately 10% of the total S is present as an insoluble or undissolved form. (3) There is 19% more S than can be accounted for by IC sulfate measurement. This additional soluble S is detected by ICP-AES analysis of the supernate. (4) Total supernate and slurry sulfur by ICP-AES should be monitored during washing in addition to supernate sulfate in order to avoid under estimating the amount of sulfur species removed or remaining in the supernate. (5) OLI simulation calculations show that the presence of undissolved Burkeite in the Tank 4 sample is reasonable, assuming a small difference in the Na concentration that is well within the analytical uncertainties of the reported value. The following conclusions were drawn from the blend studies of Tank 4 and decanted Tank 51-E1: (1) The addition of Tank 4 slurry to a decanted Tank 51-E1 sample significantly improved the degree and time for settling. (2) The addition of Tank 4 slurry to a decanted Tank 51-E1 sample significantly improved the plastic viscosity and yield stress. (3) The SRNL washing test, where nearly all of the wash solution was decanted from the solids, indicates that approximately 96% or more of the total S was removed from the blend in these tests, and the removal of the sulfur tracks closely with that of Na. Insoluble (undissolved) S remaining in the washed sludge was calculated from an estimate of the final slurry liquid fraction, the S result in the slurry digestion, and the S in the final decant (which was very close to the method detection limit). Based on this calculated result, about 4% of the initial total S remained after these washes; this amount is equivalent to about 18% of the initially undissolved S.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Availability of the B beta(15-21) epitope on cross-linked human fibrin and its plasmic degradation products

The binding of radiolabeled monoclonal antifibrin antibody 59D8 (specific for fibrin but not fibrinogen) to a series of degraded fibrin clots showed that the availability of the B beta(15-21) epitope (against which 59D8 had been raised) was inversely proportional to the extent of clot lysis. Examination of digest supernatants revealed that the B beta(15-21) epitope was released from clots as a high molecular weight degradation product in the presence of calcium ions but that the generation of low molecular weight peptides occurred in the absence of calcium ions. To address the question of epitope accessibility, we compared levels of fibrin clot binding among four radioactively labeled antibodies: antifibrin monoclonal antibody 59D8, two antifibrinogen monoclonal antibodies that cross-reacted with fibrin, and an affinity-purified polyclonal antifibrinogen antibody. We expected that the antifibrinogen antibodies would show enhanced binding to clots in comparison with the antifibrin antibody. However, the epitope accessibility experiments showed that all four antibody preparations bound fibrin clots at comparable levels. Taken together, these studies demonstrated that one fibrin-specific epitope, B beta(15-21), remains available on clots as they undergo degradation by plasmin and, importantly, that the epitope is not solubilized at a rate faster than the rate at which the clot is itself solubilized. The availability of the B beta(15-21) epitope during the course of plasminolysis assures the potential utility of antifibrin antibodies such as 59D8 for detecting thrombi and targeting plasminogen activators.

NASA Discipline Regulatory Physiology↗

Effects of Exhaust Gas Recirculation (EGR) on Turbulent Combustion and Emissions in Advanced Gas Turbine Combustors with High-Hydrogen-Content (HHC) Fuels (Final Report)

This Final Report documents the entire four years of the Cooperative Agreement DE-FE0011822, from October 1, 2013 through September 30, 2017, that was competitively awarded under Funding Opportunity Announcement DE-FOA-0000795 in support of the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) University Turbine Systems Research (UTSR) Program. Under the UTSR Program, DOE typically issues Funding Opportunity Announcement (FOA) solicitations every 1-2 years so that U.S. colleges/universities may propose research & development (R&D) projects in specific technical topic areas (e.g., combustion, aerodynamics/heat transfer, advanced materials) that have been identified as both scientifically and industrially relevant to the gas turbine industry. The primary objectives of this Purdue University project (in collaboration with Princeton University through a sub-award) was to develop experimental methods, kinetic models, and numerical tools to help quantify and predict the impact of exhaust gas recirculation (EGR) on NOx and CO emissions, combustion kinetics, radiation heat transfer, turbulent combustion, and combustion instabilities for natural gas and high hydrogen content (HHC) fuels by using laminar and turbulent flow reactors and gas turbine combustors operating at high temperatures and pressures. This project has obtained detailed data for improving chemical kinetic models to study EGR effects and provide insight into the effects of EGR on flame speeds and turbulent flame structure, as well as assessing the impact of EGR on emissions in a high-pressure combustion test rig. The project was divided into six primary tasks: 1) Project Management and Program Planning; 2) Flow Reactor Investigation of EGR Chemical Kinetics; 3) Combustion Bomb Investigation of EGR Effects on Flame Speed; 4) Investigation of EGR Effects on Turbulent Flame Structure in Reactor-Assisted Turbulent Slot (RATS) Burner; 5) Investigation of EGR Effects in Purdue Staged Combustion Test Rig; and 6) Development and Validation of a Large Eddy Simulation (LES) Tool for Gas Turbine Combustion and Emission Modeling using HHC Fuels. Details on the execution and results of each of these tasks are provided in the main report. To assist the reader, each task is described in a chapter-like format with its own separate listing of tables, figures, and references so that the results of each task/subtask (i.e., technical sections covering various experiments and modeling work focused on a specific area) can be quickly obtained while also getting an overall feel of the project execution. This chapter-like format also allows for acknowledgement of support from other programs relative to specific tasks. In this manner, the reader can more conveniently digest the R&D results in the various task/subtask sections that may be of most interest to the reader. In addition to this Final Report, the Purdue/Princeton team was able to publish 7 journal articles and provide 7 presentations at national scientific meetings/conferences to disseminate results. A listing of these journal articles and presentations is provided at the end of this report

03 NATURAL GAS↗

Thermal Desorption of Tritium from Fluoride Salt-Cooled Reactor Materials

The fluoride-salt-cooled high-temperature reactor (FHR) is a high-temperature fission reactor concept involving a liquid fluoride salt coolant, coated particle fuel, and enhanced passive safety mechanisms. Utilizing a low-pressure coolant and high temperature fuel allows for smaller reactor buildings and use of gas Brayton power cycles for higher efficiency in electricity production. One of the fluoride salts being considered for the FHR coolant is 2LiF - BeF{sub 2} (flibe). Tritium is generated frequently in flibe from thermal neutron transmutation of Li-6 and Be-9. Tritium retention in irradiated structural materials presents a challenge to the design of the FHR; high neutron fluence can induce significant material damage and alteration of microstructures to trap tritium in the structure, particularly in carbon-based materials (such as steels). Investigation of tritium transport in flibe salt and structural materials is also critical to evaluating mass balance of tritium in a system for quantifying leakage of tritium to the environment. It is important to understand the uptake of tritium in these proposed core materials since the transport of tritium within an FHR is of critical concern for operational safety due to corrosion, and to prevent tritium release into the environment. The presence of TF corrodes stainless steel by oxidizing chromium. Tritium gas (T{sub 2}) easily diffuses through reactor materials and can be released into the environment through the primary piping and heat exchangers. There is great interest in identifying materials that are compatible with the FHR environment that can be used to getter tritium from the salt, or to inhibit the diffusion of tritium to prevent its release into the environment. As part of the FHR Integrated Research Project (IRP), capsules containing proposed core materials immersed in flibe salt were irradiated at 700 deg. C for 1000 hours (FS-1) and 300 hours (FS-2) in the MIT Research Reactor (MITR). During irradiation, tritium is produced in the salt, and then interacts with the other materials in the capsule. Measurements of the effluent gas during the FHR IRP irradiation experiments indicated that less than 1% of the tritium generated in the salt escaped in the gas phase. It is assumed that most of the tritium was captured, either via diffusion or surface adsorption, on the materials inside the capsule. Tritium frequently adsorbs to sample surfaces in the form of HTO, which requires relatively low temperatures to release (on the order of 100 deg. C). In certain cases, tritium can be bound in the bulk of materials from diffusion or neutron transmutation of lithium and beryllium in the structural materials. Accurate measurement of very small concentrations of hydrogen is difficult; by taking advantage of the radioactive decay of tritium (which emits low-energy beta radiation), several methods become available to detect and quantitatively measure the tritium. The most sensitive method is liquid scintillation counting (LSC), which requires the tritium to be suspended in optically-transparent liquid media that is compatible with scintillating solution, such as water. This measurement technique requires the tritium to be extracted from the material, which can be achieved through leaching into water, thermal desorption, or complete destruction of the sample by acid digestion or pyrolysis. A less destructive method is preferred in order to preserve the specimens, reduce the generation of radioactive mixed wastes, and minimize the carryover of other activation products. For total thermal desorption of tritium from the materials, the tritiated materials must be heated to temperatures in excess of 300 deg. C. Heating the specimens above the irradiation temperature will re-mobilize the tritium and allow it to be captured from the gas stream directly into LSC media. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Life in the Clouds of Venus? An Experimental Synthetic Biology Approach

The surface of Venus constitutes the most hellish and biologically inhospitable planetary surface in our solar system, boasting a pH of 0, blistering winds that can melt lead, and pressures of 60 atm. However, during the earlier years of the solar system, without the runaway greenhouse effect that has plagued the planet, Venus potentially housed oceans and perhaps even life. There is a possibility that microbes could have retreated into hospitable niches in the atmosphere, as suggested by Carl Sagan as early as 1967 [1]. For example, 50 km above the raging hell of the Venusian surface, exists a relatively temperate environment that might serve as reservoir for life. This astrobiology project seeks to explore life at the extremes and to theorize whether microbial communities could not only survive but also reproduce in the Venusian atmosphere. Specifically, we ask: are aerosols viable microbial environments? But before we can test for life in the clouds, we have to develop a proper reporter to visualize cell growth in situ. For this purpose, we aimed to develop cell-growth dependent reporters to serve as remote biosensors for cell growth. We developed two using the polA promoter, a DNA-replication dependent promoter, and nrd operon promoter, a cell-cycle dependent promoter. Using these cell-growth reporters, the next step is to aerosolize microbes expressing these reporters in a suspension chamber adapted from a Millikan Drop Apparatus to assay reproduction in an aerosolized environment. Better yet is to test the reproduction of microbes in a microgravity regime such as on ISS.Approach: We engineered two cell-cycle dependent genetic reporters. One was the polA promoter which codes for DNA Polymerase I, a gene active in DNA replication [2]. The other was the nrdP. The activation of ribonucleotide reductase reduces ribonucleotides into deoxyribonucleotides and is involved in the bacterial cell cycle [3]. This promoter began activation during the initiation of DNA replication and is cell-cycle dependent [4]. These promoters were fused to a GFP reporter, transformed into E. coli. The constructs were deposited in the iGEM registry as K847210: Escherichia coli DNA-replication dependent polA promoter K847211: Escherichia coli cell-division dependent nrd promoter Results: Our constructs displayed fluorescence when transformed into NEB-5alpha competent cells. While nrdP-E0840 displayed sufficient fluorescence as verified by fluorescent microscopy, the original polAP-E0840 construct (which uses mut3b GFP) exhibited low expression; while fluorescence was visible under the microscope, the signal was too weak for the camera to recognize. The polA promoter was therefore digest-ed with EcoRI and SpeI then ligated into plasmid pNCS containing a RBS, Clover, and a terminator. Clover is a highly engineered green fluorescent protein that exhibits extreme brightness [5] Fluoresence time course data demonsrated that the genes were induced in a cell cycle dependant manner [6]. Our assays via microscopy and the bulk assay shows that our promoters are functional as cell cycle reporters.Conclusions: The application of such tools are widespread and not limited to astrobiology; nrdP could be used to determine doubling times empirically and could possibly extrapolate DNA content from intensity of signals expressed by polAP. However, we are pri-marily interested in its use in astrobiology.

Escherichia↗