SEARCH · Engineering Papers

Results for “COMMAND SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Development and Flight Evaluation of an Emergency Digital Flight Control System Using Only Engine Thrust on an F-15 Airplane

A propulsion-controlled aircraft (PCA) system for emergency flight control of aircraft with no flight controls was developed and flight tested on an F-15 aircraft at the NASA Dryden Flight Research Center. The airplane has been flown in a throttles-only manual mode and with an augmented system called PCA in which pilot thumbwheel commands and aircraft feedback parameters were used to drive the throttles. Results from a 36-flight evaluation showed that the PCA system can be used to safety land an airplane that has suffered a major flight control system failure. The PCA system was used to recover from a severe upset condition, descend, and land. Guest pilots have also evaluated the PCA system. This paper describes the principles of throttles-only flight control; a history of loss-of-control accidents; a description of the F-15 aircraft; the PCA system operation, simulation, and flight testing; and the pilot comments.

Burcham, Frank W., Jr.↗

NASA NTRS2006

Trajectory and Aeroheating Environment Development and Sensitivity Analysis for Capsule-shaped Vehicles

Recently, NASA's Exploration Systems Research and Technology Project funded several tasks that endeavored to develop and evaluate various thermal protection systems and high temperature material concepts for potential use on the crew exploration vehicle. In support of these tasks, NASA Langley's Vehicle Analysis Branch generated trajectory information and associated aeroheating environments for more than 60 unique entry cases. Using the Apollo Command Module as the baseline entry system because of its relevance to the favored crew exploration vehicle design, trajectories for a range of lunar and Mars return, direct and aerocapture Earth-entry scenarios were developed. For direct entry, a matrix of cases was created that reflects reasonably expected minimum and maximum values of vehicle ballistic coefficient, inertial velocity at entry interface, and inertial flight path angle at entry interface. For aerocapture, trajectories were generated for a range of values of initial velocity and ballistic coefficient that, when combined with proper initial flight path angles, resulted in achieving a low Earth orbit either by employing a full lift vector up or full lift vector down attitude. For each trajectory generated, aeroheating environments were generated which were intended to bound the thermal protection system requirements for likely crew exploration vehicle concepts. The trades examined clearly pointed to a range of missions / concepts that will require ablative systems as well as a range for which reusable systems may be feasible. In addition, the results clearly indicated those entry conditions and modes suitable for manned flight, considering vehicle deceleration levels experienced during entry. This paper presents an overview of the analysis performed, including the assumptions, methods, and general approach used, as well as a summary of the trajectory and aerothermal environment information that was generated.

Robinson, Jeffrey S.↗

NASA NTRS1989

Preliminary results on noncollocated torque control of space robot actuators

In the Space Station era, more operations will be performed robotically in space in the areas of servicing, assembly, and experiment tending among others. These robots may have various sets of requirements for accuracy, speed, and force generation, but there will be design constraints such as size, mass, and power dissipation limits. For actuation, a leading motor candidate is a dc brushless type, and there are numerous potential drive trains each with its own advantages and disadvantages. This experiment uses a harmonic drive and addresses some inherent limitations, namely its backdriveability and low frequency structural resonances. These effects are controlled and diminished by instrumenting the actuator system with a torque transducer on the output shaft. This noncollocated loop is closed to ensure that the commanded torque is accurately delivered to the manipulator link. The actuator system is modelled and its essential parameters identified. The nonlinear model for simulations will include inertias, gearing, stiction, flexibility, and the effects of output load variations. A linear model is extracted and used for designing the noncollocated torque and position feedback loops. These loops are simulated with the structural frequency encountered in the testbed system. Simulation results are given for various commands in position. The use of torque feedback is demonstrated to yield superior performance in settling time and positioning accuracy. An experimental setup being finished consists of a bench mounted motor and harmonic drive actuator system. A torque transducer and two position encoders, each with sufficient resolution and bandwidth, will provide sensory information. Parameters of the physical system are being identified and matched to analytical predictions. Initial feedback control laws will be incorporated in the bench test equipment and various experiments run to validate the designs. The status of these experiments is given.

Tilley, Scott W.↗

NASA NTRS1978

Remote lightning monitor system

An apparatus for monitoring, analyzing and accurately determining the value of peak current, the peak rate of change in current with respect to time and the rise time of the electrical currents generated in an electrical conductive mast that is located in the vicinity where lightning is to be monitored is described. The apparatus includes an electrical coil for sensing the change in current flowing through the mast and generating a voltage responsive. An on-site recorder and a recorder control system records the voltages produced responsive to lightning strikes and converts the voltage to digital signals for being transmitted back to the remote command station responsive to command signals. The recorder and the recorder control system are carried within an RFI proof environmental housing into which the command signals are fed by means of a fiber optic cable so as to minimize electrical interference.

Lennon, C. L.↗

NASA NTRS1985

Increased productivity in flight with voice commanding

Automatic Speech Recognition technology has matured to the point where it can provide a viable means of increasing productivity by naturalizing the man-machine interface. With ever increasing workloads being placed on astronauts, speech recognition may provide an alternative means of system controlling that would reduce the task burden. Voice commanding, allowing hands-free operation, can be especially effective during operations requiring simultaneous system control. A flight experiment is under development to demonstrate the operational effectiveness of voice control by commanding the Space Shuttle's Closed Circuit Television (CCIV) system. This experiment will help direct future applications of voice entry to space operations.

Jordan, W. T.↗

NASA NTRS1999

Development and Implementation of a Load-Controlled Friction Stir Welder

Lockheed Martin Michoud Space Systems, under contract to NASA/MSFC, has developed and implemented a friction stir weld tool that uses the magnitude of the spindle axial load to control the weld process. This tool was used during the process development phase and the assembly of a full-scale External Tank barrel section. Both position and load transducers are incorporated into the welder. The control algorithm allows either the position or load transducer to provide the command variable in a closed loop system. Initially, the position transducer was used to actively control the weld process and the axial load on the spindle was monitored and collected via data acquisition hardware. As part of the process development, the axial load was implemented as the command variable in the closed loop. The spindle position is monitored and used to set limits on spindle travel. A zero set point algorithm has also been developed for establishing the spindle position at the start of the weld process. In its current state, the welder operates in a dual mode in which the position control is used to plunge the pin tool to a specified depth at the initiation of the weld. The load control is then used to control the weld process. This control algorithm has been used to assemble a 27.5-ft diameter, 2195-T8 barrel using hardware designed for NASA's Space Transportation System External Tank.

Loftus, Z.↗

NASA NTRS1979

Digital adaptive controllers for VTOL vehicles. Volume 1: Concept evaluation

A digital self-adaptive flight control system was developed for flight test in the VTOL approach and landing technology (VALT) research aircraft (a modified CH-47 helicopter). The control laws accept commands from an automatic on-board guidance system. The primary objective of the control laws is to provide good command-following with a minimum cross-axis response. Three attitudes and vertical velocity are separately commanded. Adaptation of the control laws is based on information from rate and attitude gyros and a vertical velocity measurement. The final design resulted from a comparison of two different adaptive concepts--one based on explicit parameter estimates from a real-time maximum-likelihood estimation algorithm, the other based on an implicit model reference adaptive system. The two designs were compared on the basis of performance and complexity.

Hartmann, G. L.↗

NASA NTRS1993

The instant sequencing task: Toward constraint-checking a complex spacecraft command sequence interactively

Robotic spacecraft are controlled by sets of commands called 'sequences.' These sequences must be checked against mission constraints. Making our existing constraint checking program faster would enable new capabilities in our uplink process. Therefore, we are rewriting this program to run on a parallel computer. To do so, we had to determine how to run constraint-checking algorithms in parallel and create a new method of specifying spacecraft models and constraints. This new specification gives us a means of representing flight systems and their predicted response to commands which could be used in a variety of applications throughout the command process, particularly during anomaly or high-activity operations. This commonality could reduce operations cost and risk for future complex missions. Lessons learned in applying some parts of this system to the TOPEX/Poseidon mission will be described.

Horvath, Joan C.↗

NASA NTRS1985

The handling of data in solar-terrestrial and in planetary physics

The evolution of data handling systems for solar-terrestrial and planetary physics applications is discussed. The main elements of data management systems for scientific satellites are described, including: command and control; data transmission; prioritization of data users; and data reduction and analysis. The design approaches incorporated into the data management systems of the Interplanetary Monitoring Platform (IMP), International Sun Earth Explorer (ISEE), and the Orbiting Geophysical Observatory, (OGO) spacecraft, are discussed. Emphasis is given to classical, centralized, and hybrid system designs. The report of the Committee on Data Management and Computation (CODMAC) concerning concepts for new data management systems is briefly summarized.

Vette, J. I.↗

NASA NTRS1970

Apollo 13 LiOH canister breakthrough test

The Apollo 13 lithium hydroxide canister test was conducted to evaluate emergency measures designed to enable the Apollo 13 crew to use command module lithium hydroxide canisters in the lunar module. The test verified the effectiveness of the emergency system and established that the canisters in the command module would provide ample carbon dioxide removal for the return of the Apollo 13 crew. The time interval between canister changes on the flight was also determined in the test. This reduced power demand on the lunar module by eliminating the need for telemetry in determining canister replacement times. Details of the canister modifications were relayed to the flight crew and a replica of the test system was assembled in the flight vehicle. Graphs of the parameters which were measured during the simulation are presented.

Leblanc, J. C.↗

NASA NTRSDate not supplied

TECHEDSAT-7 and 10: The Little Spacecraft That Could

The NOW (Nanosatellite Orbital Workshop) of NASA Ames Research Center (ARC) has two cubesats in orbit at this time: 6 U TechEdSat-10 (T-10) and the 3U TechEdSat-7 (T-7). T10 was jettisoned from the ISS via the NANORACKS system 7/13/2020, and T-7 was launched via Virgin Orbit 1/17/2021. Both were built by the Nano-satellite Orbital Workshop (NOW) at NASA ARC, and designed and fabricated by interns and students in collaboration with educational institutions. Prototyping novel technologies for non-powered re-entry and communications from orbit are primary research interests, however all subsystems including power generation and distribution, subsystem control, navigation, positioning, heat management etc. extend current technologies. Use of distributed processors using open software platforms and standards other based technologies and software is integral to all segments of spacecraft design. Here, we will present an overview of the spacecraft, experiments, and accomplishments – as well as the next three flight experiments. Some of these experiments include: The exo-brake re-entry system is being developed to enable sample return and end of life disposal; Internal communications for sensors, inter-subsystem and experiments uses both a Zigbee based PAN and internal Wi-Fi for high-speed inter-device communications; The Iridium small message LEO system (Short Burst Data) is used to both command the spacecraft and send data to the ground; Experimental use of the Global-Star system for L-band system comparison and back-up; Collaborative NOAA an experiment to communicate from LEO to the GOES geostationary satellite using the DCS (Data Collection System) with on-board Doppler correction; Mars and Lunar experimental communication systems for future cis-lunar and interplanetary nano-satellites; First demonstration of the NASA Near Earth Network systems with nano-satellites at NASA/Wallops Island; Solar array design and implementation for unique future flexible structures; Power distribution using Tardigrade rad-hard processor omni-board (designed by the team); Distributed processors with internal Wi-Fi connectivity; and Initial experiments with AI/Machine Learning.

M Murbach↗

NASA NTRS1990

Telemetry and command standards

The first phase of the international Consultative Committee for Space Data Systems (CCSDS) efforts toward the definition of standards for space telemetry, spacecraft tracking, and command functions has established a set of standard space communications techniques capable of satisfying almost the entire spectrum of space mission user requirements. This was achieved by focusing on the distinctive problems associated with the space/ground data link, and developing the infrastructural system designated the 'Open Systems Interconnection'. The intrinsically international coordination by CCSDS of development efforts ensures highly flexible mutual support activities by the various national space agencies.

Hooke, Adrian J.↗

NASA NTRS1987

The Mission Operations Planning Assistant

The Mission Operations Planning Assistant (MOPA) is a knowledge-based system developed to support the planning and scheduling of instrument activities on the Upper Atmospheric Research Satellite (UARS). The MOPA system represents and maintains instrument plans at two levels of abstraction in order to keep plans comprehensible to both UARS Principal Investigators and Command Management personnel. The hierarchical representation of plans also allows MOPA to automatically create detailed instrument activity plans from which spacecraft command loads may be generated. The MOPA system was developed on a Symbolics 3640 computer using the ZetaLisp and ART languages. MOPA's features include a textual and graphical interface for plan inspection and modification, recognition of instrument operational constraint violations during the planning process, and consistency maintenance between the different planning levels. This paper describes the current MOPA system.

Schuetzle, James G.↗

NASA NTRS1987

The mission operations planning assistant

The Mission Operations Planning Assistant (MOPA) is a knowledge-based system developed to support the planning and scheduling of instrument activities on the Upper Atmospheric Research Satellite (UARS). The MOPA system represents and maintains instrument plans at two levels of abstraction in order to keep plans comprehensible to both UARS Prinicpal Investigators and Command Management personnel. The hierarchical representation of plans also allows MOPA to automatically create detailed instrument activity plans from which spacecraft command loads may be generated. The MOPA system was developed on a Symbolics 3640 computer using the ZETALISP and ART languages. MOPA's features include a textual and graphical interface for plan inspection and modification, recognition of instrument operational constraint violations during the planning process, and consistency maintenance between the different planning levels. This paper describes the current MOPA system.

Schuetzle, James G.↗

NASA NTRS1993

Octave: A MARSYAS post-processor for computer-aideed control system design

MARSYAS is a computer-aided control system analysis package for the simulation and analysis of dynamic systems. In the summer of 1991 MARSYAS was updated to allow for the analysis of sampled-data systems in terms of frequency response, stability, etc. This update was continued during the summer of 1992 in order to extend further MARSYAS commands to the study of sampled data systems. Further work was done to examine the computation of openat transfer functions, root-locii and omega-plane frequency response plots. At the conclusion of the summer of 1992 work, it was proposed that control-system design capability be incorporated into the MARSYAS package. It was decided at that time to develop a separate 'stand-alone' computer-aided control system design (CACSD) package. This report is a brief description of such a package.

Hodel, A. Scottedward↗

DOE OSTI2017

A novel priority selection system for nuclear power plant - 287

The priority selection system is an important component of security level instrument control platform for nuclear power plant, the main function of which is priority processing the manual or automatic command with various security levels and driving engineering safety features and field devices, such as pump and valve. Its stability and safety plays a crucial role in the operation of the power plant. The main objective of the present paper is to describe the new nuclear power plant-oriented priority selection system, which is developed independently by China Nuclear Control System Engineering Company. In this system, the control commands from 1E DCS, ECP and DAS systems are transmitted via hardwire, while those from NC DCS are transmitted by field-bus. The control commands experience priority output to control the field actuators. Meanwhile, in order to control key field devices when failure of the instrument control systems occurs, the issuing interface for native instructions with permissions setting is also offered. The whole system provides collection-feedback functions for field devices, high coverage self-diagnostic functions and periodic test functions for safety systems. Moreover, the feedback information of field devices, the results of self-diagnosis and periodic test will be submitted to DCS of nuclear power plant. In addition, the core part of priority selection system, namely priority selection module, is obtained by pure FPGA technology, which is different from DCS systems and could avoid common cause failure of software effectively. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1994

Global Positioning System Synchronized Active Light Autonomous Docking System

A Global Positioning System Synchronized Active Light Autonomous Docking System (GPSSALADS) for automatically docking a chase vehicle with a target vehicle comprises at least one active light emitting target which is operatively attached to the target vehicle. The target includes a three-dimensional array of concomitantly flashing lights which flash at a controlled common frequency. The GPSSALADS further comprises a visual tracking sensor operatively attached to the chase vehicle for detecting and tracking the target vehicle. Its performance is synchronized with the flash frequency of the lights by a synchronization means which is comprised of first and second internal clocks operatively connected to the active light target and visual tracking sensor, respectively, for providing timing control signals thereto, respectively. The synchronization means further includes first and second Global Positioning System receivers operatively connected to the first and second internal clocks, respectively, for repeatedly providing simultaneous synchronization pulses to the internal clocks, respectively. In addition, the GPSSALADS includes a docking process controller means which is operatively attached to the chase vehicle and is responsive to the visual tracking sensor for producing commands for the guidance and propulsion system of the chase vehicle.

Howard, Richard↗

NASA NTRS1996

Global Positioning System Synchronized Active Light Autonomous Docking System

A Global Positioning System Synchronized Active Light Autonomous Docking System (GPSSALADS) for automatically docking a chase vehicle with a target vehicle comprising at least one active light emitting target which is operatively attached to the target vehicle. The target includes a three-dimensional array of concomitantly flashing lights which flash at a controlled common frequency. The GPSSALADS further comprises a visual tracking sensor operatively attached to the chase vehicle for detecting and tracking the target vehicle. Its performance is synchronized with the flash frequency of the lights by a synchronization means which is comprised of first and second internal clocks operatively connected to the active light target and visual tracking sensor, respectively, for providing timing control signals thereto, respectively. The synchronization means further includes first and second Global Positioning System receivers operatively connected to the first and second internal clocks, respectively, for repeatedly providing simultaneous synchronization pulses to the internal clocks, respectively. In addition, the GPSSALADS includes a docking process controller means which is operatively attached to the chase vehicle and is responsive to the visual tracking sensor for producing commands for the guidance and propulsion system of the chase vehicle.

Howard, Richard T.↗