Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Mid-infrared Pulsed Upconversion Imaging in a Rotating Detonation Combustor

To meet the challenges associated with performing mid-InfraRed (IR) imaging in Rotating Detonation Combustors (RDCs), a novel pulsed mid-IR UpConversion Imaging (UCI) diagnostic has been implemented. UCI is an alternative to direct mid-IR detection that uses nonlinear optical frequency mixing to shift mid-IR wavelengths carrying a target image to shorter wavelengths that can be imaged with high-performance silicon-based CCD/CMOS cameras. This approach offers several favorable properties including high spectral selectivity, high temporal resolution, and superior low-light detectivity. A hydrogen-air research RDC was operated with carbon dioxide addition to allow pulsed UCI imaging of mid-IR luminosity within the combustion channel from spontaneous thermal emissions. The resulting measurements demonstrate high spatiotemporal resolution capable of imaging small structures near the supersonically propagating detonation wave front. The results show how this technique can be used to observe sharp gradients and millimeter-scale structures in the high-temperature, high-pressure zones RDC flow fields.

White, Logan W.↗

Characterization of Hydrocarbon Emissions from Gasoline Direct-Injection Compression Ignition Engine Operating on a Higher Reactivity Gasoline Fuel

Low temperature combustion engine technologies are being investigated for high efficiency and low emissions. However, such engine technologies often produce higher engine-out hydrocarbon (HC) and carbon monoxide (CO) emissions, and their operating range is limited by the fuel properties. In this study, two different fuels, a US market gasoline containing 10% ethanol (RON 92 E10) and a higher reactivity gasoline (RON 80 E0), were compared on a Delphi’s second generation Gasoline Direct-Injection Compression Ignition (Gen 2.0 GDCI) multi-cylinder engine. The engine was evaluated at three operating points ranging from a light load condition (800 rpm/2 bar IMEP g ) to medium load conditions (1500 rpm/6 bar and 2000 rpm/10 bar IMEP g ). The engine was equipped with two oxidation catalysts, between which was located the exhaust gas recirculation (EGR) inlet. Samples were taken at engine-out, between the catalysts, and at tailpipe locations. In addition, part of the raw exhaust was diluted and sampled for HC speciation. Canisters and sorbent membranes were used to collect volatile HCs and semi-volatile HCs, respectively. Di-nitrophenyl hydrazine (DNPH) cartridges were also used for collecting oxygenated species. Results showed overall lower HC emissions with the RON 80 E0 fuel compared to the RON 92 E10 fuel. For both fuels, the percentage of aromatic HCs was higher in the exhaust than in the fuels themselves. High engine-out aldehyde and ketone emissions were observed for both fuels. The reported HC speciation information can be useful for the development of a robust emission control system.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Zirconium modified nickel-copper alloy

An improved material for use in a catalytic reactor which reduces nitrogen oxide from internal combustion engines is in the form of a zirconium-modified, precipitation-strengthened nickel-copper alloy. This material has a nominal composition of Ni-30 Cu-0.2 Zr and is characterized by improved high temperature mechanical properties.

Whittenberger, J. D.↗

Latest developments in cryogenic safety

The Cryogenic Safety Manual, sponsored by the British Cryogenics Council, was published over 10 years ago. A new updated version is now available. Some general aspects of cryogenic safety are highlighted, and attention is drawn to some of the more unusual hazardous situations. An awareness of the physical properties of the cryogenic fluids being dealt with is important in directing attention to hazardous situations which may arise. Because of this, the more important properties of the cryogenic fluids are given, such as molecular weight, boiling point and freezing point. From these properties, hazardous situations can be deduced. There are hidden dangers that are not always easy to spot. Some of the unexpected hazards, most of which have led to deaths, are: asphyxiation (anoxia), frost bites and hypothermia, explosions, and combustion. The aim of this publication is to help bring about increased safety in the production and use of cryogenic products through a deeper appreciation of the scientific, technological and administrative steps which must be made if accidents, some fatal, are to be voided in the future.

Webster, T. J.↗

Performance comparisons of Navy jet mix and MIL-F-5624A (JP-3) fuels in tubular and annular combustors / Richard J. McCafferty

The performances of Navy Jet Mix and MIL-F-5624A (JP-3) fuels were compared in J33, J47, and NACA experimental annular combustion chambers. Combustion efficiencies, altitude operational limits, and carbon-forming tendencies wer determined and discussed. The results indicate that Jet Mix fuel can be utilized satisfactorily in a number of current turbojet engines over the normal operating range. Small differences in combustion efficiences and altitude operational limits existed between the two fuels but these differences depended on the particular combustor and simulated altitude and rotor speed condition. Excessive carbon deposition is not predicted for Jet Mix fuel, although this property may be marginal.

Mccafferty, Richard J↗

Flame Retardant Epoxy Resins

As part of a program to develop fire resistant exterior composite structures for future subsonic commercial aircraft, flame retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured epoxies were characterized by thermogravimetric analysis, propane torch test, elemental analysis and microscale combustion calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness of plaques of several cured formulations was determined on single-edge notched bend specimens. The chemistry and properties of these new epoxy formulations are discussed.

Thompson, C. M.↗

Lean Blowout (LBO) Simulations in a Rich-Burn Quick-Quench Lean-Burn (RQL) Gas Turbine Combustor

The transient processes involving lean blowout (LBO) in a RQL combustor such as the single cup combustor in the National Jet Fuels Combustion Program (NJFCP) referee rig are simulated with the reduced mechanisms based on Hybrid Chemistry for two different fuels, Cat-A2 and Cat-C1. Cat-A2 fuel is Jet-A with average or nominal properties based on a survey of the Petroleum Quality Information System database. The Cat-C1, an alternative jet fuel, is a GEVO alcohol-to-jet (ATJ) fuel composed almost entirely of two highly-branched C12 and C16 iso-paraffins. Experiments conducted in the NJFCP referee rig established a stable flame at an equivalence ratio of 0.096 (the near LBO condition) as the starting condition for LBO tests performed with all Category A and C fuels. Simulations of the approach to LBO verify that a stable flame is established at the near-LBO condition for each fuel before reducing fuel flow rate (and thus equivalence ratio) in a step-wise manner. At each new equivalence ratio, the global heat release rate and total fuel evaporation time histories are monitored to verify a new stable flame condition has been established before performing the next reduction in equivalence ratio until the flame is approaching the blowout. Main conclusions are threefold: (1) For Cat-C1 fuel the equivalence ratio for LBO is around 0.087. (2) For Cat-A2 fuel the equivalence ratio for LBO is either 0.082 or 0.078 depended on the time span of equivalence ratio of 0.085. (3) The averaged difference from LES on LBO for Cat-C1 relative to Cat-A2 is 8.75% versus 7.8% from the experimental data.

LES, Lean blow out↗

FY2016 Propulsion Materials Annual Progress Report

The Propulsion Materials Program actively supports the energy security and reduction of greenhouse emissions goals of VTO by investigating and identifying the materials properties that are most essential for continued development of cost-effective, highly efficient, and environmentally friendly next-generation heavy and light-duty powertrains. The technical approaches available to enhance propulsion systems focus on improvements in both vehicle efficiency and fuel substitution, both of which must overcome the performance limitations of the materials currently in use. Propulsion Materials Program activities work with national laboratories, industry experts, and VTO powertrain systems (e.g., Advanced Combustion Engines and Fuels) teams to develop strategies that overcome materials limitations in future powertrain performance. The technical maturity of the portfolio of funded projects ranges from basic science to subsystem prototype validation. Projects within a Propulsion Materials Program activity address materials concerns that directly impact critical technology barriers within each of the above programs, including barriers that impact fuel efficiency, thermal management, emissions reduction, improved reliability, and reduced manufacturing costs. The program engages only the barriers that result from material property limitations and represent fundamental, high-risk materials issues.

33 ADVANCED PROPULSION SYSTEMS↗

Lab-scale Lidar Sensing of Diesel Engines Exhausts

Combustion technology and its environmental concerns are being considered with increasing attention, not only for global-scale effects, but also for toxicological implications, particularly in the lift conditions of traffic-congested areas and industrial sites. Majority combustion by-products (CO, NO(sub x)) and unburned hydrocarbons (HC), are already subject to increasingly severe regulations; however other, non-regulated minority species, mainly soot and heavy aromatic molecules, involve higher health risks, as they are suspected to be agents of serious pathologies and even mutagenic effects. This is but one of the reasons why much research work is being carried out worldwide on the physical properties of these substances. Correspondingly, the need arises to detect their presence in urban environments, with as high a sensitivity as is required by their low concentrations, proper time- and space-resolutions, and 'real-time' capabilities. Lidar techniques are excellent candidates to this purpose, although severe constraints limit their applicability, eye-safety problems and aerosol Mie scattering uncertainties above all. At CNR's Istituto Motori in Napels, a Lidar-like diagnostic system is being developed, aimed primarily at monitoring the dynamic behavior of internal combustion engines, particularly diesel exhausts, and at exploring the feasibility of a so-called 'Downtown Lidar'.

Borghese, A.↗

Spherically expanding flame in silane–hydrogen–nitrous oxide–argon mixtures

The effect of silane addition on the laminar flame speed ($S^0_u$) of flames propagating in hydrogen–nitrous oxide–argon mixtures has been investigated experimentally for the first time using the spherically expanding flame technique in a constant volume combustion chamber. Replacing hydrogen by silane and maintaining the equivalence ratio constant, much higher flame speeds, explosion peak pressures, and pressure rise coefficients were measured. A previously developed detailed reaction model has been updated based on ab initio thermodynamic properties calculations and collision limit violation analysis. The improved reaction model demonstrates encouraging performance in predicting the flame speed, with a mean absolute error below 11%. To explain the effect of silane addition on the flame dynamics, a number of parameters have been calculated including OH and H rate of production, heat release rate per reaction, and sensitivity coefficient on . The dynamics of freely propagating flames in SiH 4 –H 2 –N 2 O–Ar mixtures is essentially controlled by reactions of the H–O–N chemical system: N 2 O+H=N 2 +OH, OH+H 2 =H 2 O+H, and N 2 O(+M)=N 2 +O(+M). Whereas silane addition does not influence much the rate of production of OH, it significantly modifies that of H with a number of pyrolytic chemical pathways of silicon hydrides, such as SiH+H 2 =SiH 2 +H and Si+H 2 =SiH+H, which act as sink of H atom as they proceed in the backward direction. The reactions forming SiO(s) and SiO 2 (s), such as SiO+OH=SiO 2 (s)+H and 2SiO=2SiO(s), are exothermic and significantly contribute to the temperature increase. The adiabatic, constant pressure flame temperature for mixture containing silane is significantly higher, up to several 100’s K. The increase of induced by silane addition seems to be mostly related to the large increase of the flame temperature which leads to higher energy release rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Re-evaluation of rate constants for the reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M)

Rate constants for the dissociation/recombination reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M) are determined by a combination of quantum-chemical calculations and statistical unimolecular rate theory. Between 1100 and 2500 K, limiting low-pressure rate constants for hydrazine dissociation in the bath gas Ar of k 0 = [Ar] 6.1 × 10 20 (T/1000 K) –7.3 exp (-34490 K/T) cm 3 mol –1 s –1 , limiting high-pressure rate constants of k ∞ = 7.6 × 10 16 (T/1000 K) –1.0 exp(-33600 K/T) s –1 , and center broadening factors of the falloff curves (between 1100 and 1600 K in Ar) of F cent = 0.71 exp(- T/1460 K) + 0.29 exp(- T/21 K) + exp(-13400 K/T) were calculated. Using equilibrium constants K C = 1.7 × 10 3 (T/1000 K) –1.5 exp(-33,460 K/T) mol cm –3 , between 300 and 600 K limiting low-pressure rate constants for the reverse recombination of NH 2 radicals in the bath gas N 2 of k rec,0 = [N 2 ] 4.4 × 10 20 (T/400 K) –6.9 exp (-1630 K/T) cm 6 mol –2 s –1 , limiting high-pressure rate constants of k rec,∞ = 4.4 × 10 13 (T/1000 K) 0.44 exp(-140 K/T) cm 3 mol -1 s –1 , and center broadening factors (between 300 and 600 K in N 2 ) of F cent = exp(- T/1130 K) + exp (-10340 K/T) were obtained. A comparison with experimental results for hydrazine dissociation from the literature suggests incomplete falloff extrapolations toward k ∞ and experimental problems in the determination of k 0 at temperatures above about 1600 K. Finally, implications of the present re-evaluated rate constants for the modeling of high temperature ammonia oxidation kinetics are discussed, showing an only small influence of their precise values on the overall properties of the process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In Situ Synthesis of Phosphate-Based CelloMOF as a Promising Separator for Li–Ion Batteries

Nowadays, battery separators play a critical role in determining the sustainability, electrochemical efficiency, and safety of lithium-ion batteries (LIBs). In this contribution, we developed fire-resistant composite membranes called CelloMOF by in situ grafting of metal-organic framework, ZIF-67, onto phosphorylated cellulose nanofibers (P-CNFs) followed by a vacuum filtration process akin to papermaking. The hybrid ZIF-67@P-CNF membrane exhibits superior properties than a polyolefin-based commercial separator (CS) in terms of enhanced thermal and dimensional stability, flame-retardant properties, better surface wettability, and improved electrolyte uptake. Thermal dimensional stability tests revealed that the ZIF-67@P-CNF separator maintained its structure even at 200 °C, whereas CS suffered severe shrinkage, potentially leading to internal short circuits. Combustion tests showed a peak heat release rate (PHRR) of 34.5 W/g and a total heat release (THR) of 1.61 kJ/g for ZIF-67@P-CNF, significantly lower than the PHRR (1111.82 W/g) and THR (40.89 kJ/g) of CS. The composite separator also demonstrated significantly improved wettability, with a contact angle of 32 ± 1.04°, compared to 92 ± 1.07° for CS, highlighting its hydrophilic nature. Electrochemical evaluations in LiFePO 4 /Li half-cells indicated a higher discharge capacity of 149 mA h g -1 at 0.2 C and superior capacity retention of 86% after 50 cycles, outperforming CS (145 mA h g -1 and 84%, respectively). In conclusion, these results underscore the potential of the ZIF-67@P-CNF membrane to advance safe, high-performance LIBs by addressing critical challenges in thermal stability, flame retardancy, and electrolyte compatibility.

ZIF-67↗

Sorbent-based Oxygen Production for Energy Systems

Project DE-FE0024075 deals with the development of a moderate-temperature sorbent-based oxygen production technology. Sorbent-based oxygen production process utilizes oxygen-storage properties of Perovskites to (1) adsorb oxygen from air in a solid sorbent, and (2) release the adsorbed oxygen into a sweep gas such as CO 2 and/or steam for gasification systems or recycled flue gas for oxy-combustion systems. Pure oxygen can be produced by the use of vacuum instead of a sweep gas to affect the pressure swing. By developing more efficient and stable, higher sorption capacity, newer class of materials operating at moderate temperatures this process represents a major advancement in air separation technology. Newly developed perovskite ceramic sorbent materials with order-disorder transition have a higher O 2 adsorption capacity, potentially 200 °C lower operating temperatures, and up to two orders of magnitude faster desorption rates than those used in earlier development efforts. The performance advancements afforded by the new materials lead to substantial savings in capital investment and operational costs. Cost of producing oxygen using sorbents could be as much as 26% lower than VPSA and about 13% lower than a large cryogenic air separation unit. Cost advantage against large cryogenic separation is limited because sorbent-based separation numbers up sorbent modules for achieving the larger capacity.

01 COAL, LIGNITE, AND PEAT↗

Sorbent-based Oxygen Production for Energy Systems

Project DE-FE0024075 deals with the development of a moderate-temperature sorbent-based oxygen production technology. Sorbent-based oxygen production process utilizes oxygen-storage properties of Perovskites to (1) adsorb oxygen from air in a solid sorbent, and (2) release the adsorbed oxygen into a sweep gas such as CO 2 and/or steam for gasification systems or recycled flue gas for oxy-combustion systems. Pure oxygen can be produced by the use of vacuum instead of a sweep gas to affect the pressure swing. By developing more efficient and stable, higher sorption capacity, newer class of materials operating at moderate temperatures this process represents a major advancement in air separation technology. Newly developed perovskite ceramic sorbent materials with order-disorder transition have a higher O 2 adsorption capacity, potentially 200 ºC lower operating temperatures, and up to two orders of magnitude faster desorption rates than those used in earlier development efforts. The performance advancements afforded by the new materials lead to substantial savings in capital investment and operational costs. Cost of producing oxygen using sorbents could be as much as 26% lower than VPSA and about 13% lower than a large cryogenic air separation unit. Cost advantage against large cryogenic separation is limited because sorbent-based separation numbers up sorbent modules for achieving the larger capacity.

01 COAL, LIGNITE, AND PEAT↗

Research on aviation fuel instability

Current aircraft turbine fuels do not present a significant problem with fuel thermal stability. However, turbine fuels with broadened properties or nonpetroleum derived fuels may have reduced thermal stability because of their higher content of olefins, heteroatoms, and trace metals. Moreover, advanced turbine engines will increase the thermal stress on fuels because of their higher pressure ratios and combustion temperature. In recognition of the importance of this problem, NASA Lewis is currently engaged in a broadly based research effort to better understand the underlying causes of fuel thermal degradation. The progress and status of our various activities in this area are discussed. Topics covered include: nature of fuel instability and its temperature dependence, methods of measuring the instability, chemical mechanisms involved in deposit formation, and instrumental methods for characterizing fuel deposits. Finally, some preliminary thoughts on design approaches for minimizing the effects of lowered thermal stability are briefly discussed.

Baker, C. E.↗

A Rocket Engine Design Expert System

The overall structure and capabilities of an expert system designed to evaluate rocket engine performance are described. The expert system incorporates a JANNAF standard reference computer code to determine rocket engine performance and a state of the art finite element computer code to calculate the interactions between propellant injection, energy release in the combustion chamber, and regenerative cooling heat transfer. Rule-of-thumb heuristics were incorporated for the H2-O2 coaxial injector design, including a minimum gap size constraint on the total number of injector elements. One dimensional equilibrium chemistry was used in the energy release analysis of the combustion chamber. A 3-D conduction and/or 1-D advection analysis is used to predict heat transfer and coolant channel wall temperature distributions, in addition to coolant temperature and pressure drop. Inputting values to describe the geometry and state properties of the entire system is done directly from the computer keyboard. Graphical display of all output results from the computer code analyses is facilitated by menu selection of up to five dependent variables per plot.

Davidian, Kenneth J.↗