SEARCH · Engineering Papers

Results for “BLADE TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Aeroacoustic effects of reduced aft tip speed at constant thrust for a model counterrotation turboprop at takeoff conditions

A model high-speed, advanced counterrotation propeller, F7/A7, was tested in the NASA Lewis Research Center's 9- by 15-foot anechoic wind tunnel at simulated takeoff and approach conditions of Mach 0.2. The propeller was operated in a baseline configuration with the forward and aft rotor blade setting angles (36.2deg and 35.4 deg) and forward and aft rotational speeds essentially equal. Two additional configurations were tested with the aft rotor at increased blade setting angles and the rotational speed reduced to achieve overall performance similar to that of the baseline configuration. The aft rotor blade angles were adjusted such that the thrust and power absorption for each rotor remained the same as for the baseline configuration. Acoustic data were taken with an axially translating microphone probe that was attached to the tunnel floor. Concurrent aerodynamic data were taken to define propeller operating conditions. The aft rotor fundamental tone was about 6 dB lower with the 36.2 deg and 38.4 deg blade setting angles, and about 9 dB lower with the 36.2 and 41.4 deg blade setting angles. Predicted noise reductions based on tip speed considerations were 5 and 9.5 dB, respectively, for the two altered blade setting angles.

Woodward, Richard P.↗

NASA NTRS1980

A flight investigation of blade section aerodynamics for a helicopter main rotor having NLR-1T airfoil sections

A flight investigation was conducted using a teetering-rotor AH-1G helicopter to obtain data on the aerodynamic behavior of main-rotor blades with the NLR-1T blade section. The data system recorded blade-section aerodynamic pressures at 90 percent rotor radius as well as vehicle flight state, performance, and loads. The test envelope included hover, forward flight, and collective-fixed maneuvers. Data were obtained on apparent blade-vortex interactions, negative lift on the advancing blade in high-speed flight and wake interactions in hover. In many cases, good agreement was achieved between chordwise pressure distributions predicted by airfoil theory and flight data with no apparent indications of blade-vortex interactions.

Morris, C. E. K., Jr.↗

NASA NTRSDate not supplied

An Examination of Causes of Multi-Wire Bias During SLD Instrumentation Testing in the IRT

The Icing Research Tunnel (IRT) at NASA Glenn Research Center has been using the SEA Multi-Element Sensor (aka, the multi-wire) as its primary liquid water content instrument since 2011. Recent tests in the IRT with four different multi-wire probes (i.e., different serial numbers) have indicated situations that can result in biasing of the probe data. The reference data used in this report are multi-wire data that have been proven to agree well with the icing blade in low-impingement rate conditions. Data from these recent tests suggest that the presence of a canister probe located 4.45 ft axially downstream and 2.5 ft to the side may have caused multi-wire data to read around 5% low at an airspeed of 150 kts. Additionally, two probes of different serial numbers were observed to measure 5-15% lower than the reference probes, and the causes have been linked to excessive solder on the sensing element and to an out of date element calibration. For these reasons, the authors suggest the community be aware of the possible aerodynamic influences on the probe inlet and outlet, as well as the importance of regular calibration and maintenance of the probes.

aircraft icing↗

NASA NTRSDate not supplied

An Examination of Causes of Multi-Wire Bias during SLD Instrumentation Testing in the IRT

aircraft icing↗

NASA NTRS1974

High-tip-speed, low-loading transonic fan stage. Part 3: Final report

Tests were conducted on a high-tip-speed, low-loading transonic fan stage to determine the performance and inlet flow distortion tolerance of the design. The fan was designed for high efficiency at a moderate pressure ratio by designing the hub section to operate at minimum loss when the tip operates with an oblique shock. The design objective was an efficiency of 86 percent at a pressure ratio of 1.5, a specific flow (flow per unit annulus area) of 42 lb/sec-sq. ft (205.1 kgm/sec-m sq), and a tip speed of 1600 ft/sec (488.6 m/sec). During testing, a peak efficiency of 84 percent was achieved at design speed and design specific flow. At the design speed and pressure ratio, the flow was 4 percent greater than design, efficiency was 81 percent, and a stall margin of 24 percent was obtained. The stall line was improved with hub radial distortion but was reduced when the stage was tested with tip radial and circumferential flow distortions. Blade-to-blade values of static pressures were measured over the rotor blade tips.

Ware, T. C.↗

NASA NTRS1975

Three dimensional flow field in rocket pump inducers. Part 2: Mean flow and turbulence characteristics inside the rotor passage, and theoretical analysis

The measurement and prediction is reported of three dimensional flow fields in an axial flow inducer operating at a flow coefficient of 0.065 with air as the test medium. The experimental investigations included measurements of the blade static pressure and blade limiting streamline angle, and measurement of the three components of mean velocity, turbulence intensities and turbulence stresses at locations inside the inducer blade passage utilizing a rotating three-sensor hotwire probe. Analytical investigations were conducted to predict the three-dimensional inviscid flow. Total relative velocity distributions indicate a substantial velocity deficiency near the tip at mid-passage. High turbulence intensities and turbulence stresses are concentrated within this core region. Evidence of boundary layer interactions, blade blockage effects, radially inward flows, annulus wall effects and backflows are found to exist within the long, narrow passages of the inducer, emphasizing the complex nature of inducer flow which makes accurate prediction of the flow behavior extremely difficult.

Lakshminarayana, B.↗

NASA NTRS1977

Finite Element Stability Analysis for Coupled Rotor and Support Systems

The effects of fuselage motions on stability and random response were analytically assessed. The feasibility of adequate perturbation models from non-linear trim conditions was studied by computer and hardware experiments. Rotor wake-blade interactions were assessed by using a 4-bladed rotor model with the capability of progressing and regressing blade pitch excitation (cyclic pitch stirring), by using a 4-bladed rotor model with hub tilt stirring, and by testing rotor models in sinusoidal up or side flow.

Hohenemser, K. H.↗

NASA NTRS1979

Preliminary analysis of performance and loads data from the 2-megawatt mod-1 wind turbine generator

Preliminary test data on output power versus wind speed, rotor blade loads, system dynamic behavior, and start-stop characteristics on the Mod-1 wind turbine generator are presented. These data were analyzed statistically and are compared with design predictions of system performance and loads. To date, the Mod-1 wind turbine generator has produced up to 1.5 MW of power, with a measured power versus wind speed curve which agrees closely with design. Blade loads were measured at wind speeds up to 14 m/s and also during rapid shutdowns. Peak transient loads during the most severe shutdowns are less than the design limit loads. On the inboard blade sections, fatigue loads are approximately equal to the design cyclic loads. On the outboard blade sections, however, measured cyclic loads are significantly larger than design values, but they do not appear to exceed fatigue allowable loads as yet.

Spera, D. A.↗

NASA NTRS1980

Acoustic pressures on a prop-fan aircraft fuselage surface

Acoustic pressure amplitude and phase distributions on the surface of a simulated fuselage (a rigid semi-cylinder) installed in an acoustically treated wind tunnel near a Prop-Fan model were measured. The test conditions simulated the relative tip Mach number and blade loading of a full scale Prop-Fan at high altitude 0.8 Mach number cruise. Measurements were also made at equivalent microphone locations without the semi-cylinder to establish the effects of the presence of a fuselage on the sound pressure amplitudes. These effects were found to be 6 dB at 90 degrees incidence, decreasing to no effect at grazing incidence. Comparison of measurements and calculations using a Hamilton Standard Prop-Fan noise calculation computer program showed good agreement in peak level and in phase distribution. Continuous recordings were also made of a Prop-Fan RPM sweep at constant simulated flight speed and a simulated flight speed sweep at constant Prop-Fan RPM. These showed smooth variations in noise level over the tip Mach number range 0.878 to 1.143.

Magliozzi, B.↗

NASA NTRS1981

Concepts for improving the damage tolerance of composite compression panels

The results of an experimental evaluation of graphite-epoxy composite compression panel impact damage tolerance and damage propagation arrest concepts are reported. The tests were conducted on flat plate specimens and blade-stiffened structural panels such as those used in commercial aircraft wings, and the residual strength of damaged specimens and their sensitivity to damage while subjected to in-plane compression loading were determined. Results suggest that matrix materials that fail by delamination have the lowest damage tolerance, and it is concluded that alternative matrix materials with transverse reinforcement to suppress the delamination failure mode and yield the higher-strain value transverse shear crippling mode should be developed.

Rhodes, M. D.↗

NASA NTRS1983

Properties of Nickel-Based Hydrogen-Turbine Blades

120 page report presents data on mechanical properties of cast nickelbased alloys for turbine blades operating in hydrogen and steam at high temperatures. Tests on alloys for hydrogen-burning engines of future are described.

Deluca, D. P.↗

NASA NTRS1982

Rotorcraft Blade Mode Damping Identification from Random Responses Using a Recursive Maximum Likelihood Algorithm

An on line technique is presented for the identification of rotor blade modal damping and frequency from rotorcraft random response test data. The identification technique is based upon a recursive maximum likelihood (RML) algorithm, which is demonstrated to have excellent convergence characteristics in the presence of random measurement noise and random excitation. The RML technique requires virtually no user interaction, provides accurate confidence bands on the parameter estimates, and can be used for continuous monitoring of modal damping during wind tunnel or flight testing. Results are presented from simulation random response data which quantify the identified parameter convergence behavior for various levels of random excitation. The data length required for acceptable parameter accuracy is shown to depend upon the amplitude of random response and the modal damping level. Random response amplitudes of 1.25 degrees to .05 degrees are investigated. The RML technique is applied to hingeless rotor test data. The inplane lag regressing mode is identified at different rotor speeds. The identification from the test data is compared with the simulation results and with other available estimates of frequency and damping.

Molusis, J. A.↗

NASA NTRS1982

Measured performance of a tip-controlled, teetered rotor with an NACA 64 sub 3-618 tip airfoil

Tests were conducted on the Mod-O 100 kW Wind Turbine to determine the performance of a tip-controlled rotor having an NACA 64 sub-618 airfoil over the moveable outboard 30% of the blade, while operating at nominal rotor speeds of 21 and 31 rpm. Tests were conducted at two rotor speeds to assess the performance improvement which could be realized with 2-speed operation. Test data are compared with analytical predictions and concluding remarks are presented. The results indicate a clear performance improvement for the 2-speed operation.

Corrigan, R. D.↗

NASA NTRS1984

Reusable rocket engine turbopump condition monitoring

Significant improvements in engine readiness with reductions in maintenance costs and turn-around times can be achieved with an engine condition monitoring systems (CMS). The CMS provides health status of critical engine components, without disassembly, through monitoring with advanced sensors. Engine failure reports over 35 years were categorized into 20 different modes of failure. Rotor bearings and turbine blades were determined to be the most critical in limiting turbopump life. Measurement technologies were matched to each of the failure modes identified. Three were selected to monitor the rotor bearings and turbine blades: the isotope wear detector and fiberoptic deflectometer (bearings), and the fiberoptic pyrometer (blades). Signal processing algorithms were evaluated for their ability to provide useful health data to maintenance personnel. Design modifications to the Space Shuttle Main Engine (SSME) high pressure turbopumps were developed to incorporate the sensors. Laboratory test fixtures have been designed for monitoring the rotor bearings and turbine blades in simulated turbopump operating conditions.

Hampson, M. E.↗

NASA NTRS1987

Low-cost FM oscillator for capacitance type of blade tip clearance measurement system

The frequency-modulated (FM) oscillator described is part of a blade tip clearance measurement system that meets the needs of a wide class of fans, compressors, and turbines. As a result of advancements in the technology of ultra-high-frequency operational amplifiers, the FM oscillator requires only a single low-cost integrated circuit. Its carrier frequency is 42.8 MHz when it is used with an integrated probe and connecting cable assembly consisting of a 0.81 cm diameter engine-mounted capacitance probe and a 61 cm long hermetically sealed coaxial cable. A complete circuit analysis is given, including amplifier negative resistance characteristics. An error analysis of environmentally induced effects is also derived, and an error-correcting technique is proposed. The oscillator can be calibrated in the static mode and has a negative peak frequency deviation of 400 kHz for a rotor blade thickness of 1.2 mm. High-temperature performance tests of the probe and 13 cm of the adjacent cable show good accuracy up to 600 C, the maximum permissible seal temperature. The major source of error is the residual FM oscillator noise, which produces a clearance error of + or - 10 microns at a clearance of 0.5 mm. The oscillator electronics accommodates the high rotor speeds associated with small engines, the signals from which may have frequency components as high as 1 MHz.

Barranger, John P.↗

NASA NTRS1991

The design/analysis of flows through turbomachinery: A viscous/inviscid approach

The development of a design/analysis flow solver at NASA Lewis Research Center is discussed. The solver is axisymmetric and can be run inviscidly with assumed or calculated blockages, or with the viscous terms computed. The blade forces for each blade row are computed from blade-to-blade solutions, correlated data or force model, or from a full three dimensional solution. Codes currently under development can be separated into three distinct elements: the turbomachinery interactive grid generator energy distribution restart code (TIGGERC), the interactive blade element geometry generator (IBEGG), and the viscous/inviscid multi-blade-row average passage flow solver (VIADAC). Several experimental test cases were run to validate the VIADAC code. The tests, representative of typical axial turbomachinery duct axisymmetric wind tunnel body problems, were conducted on an SR7 Spinner axisymmetric body, a NASA Rotor 67 Fan test bed, and a transonic boatail body. The results show the computations to be in good agreement with test data.

Miller, D. P.↗

NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler Velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels.

Woodward, Richard P.↗

NASA NTRS1933

Experiments with a Counter-propeller

This note describes tests made at Stanford University on a four-blade fixed counter-propeller in combination with a two-blade rotating propeller. It is shown that the efficiency of the normal form, well-designed air propeller can be increased about two percent over the full working range by the addition of fixed counter-propeller blades.

Lesley, E P↗