Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution, volume 2

Data presented were obtained during wind tunnel tests of a 0.0405-scale model of the -89B ferry configuration of the space shuttle vehicle orbiter. These tests were conducted in the Rockwell International low speed wind tunnel (NAAL). The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration has a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRS1930

Joint Report on Standardization Tests on N.P.L. R.A.F 15 Airfoil Model

This report contains the wind-tunnel test data obtained in the United States on a 36 by 6 inch R.A.F. 15 airfoil model prepared by the British Aeronautical Research Committee for International Trials. Tests were made in cooperation with the National Advisory Committee for Aeronautics at the Bureau of Standards, Langley Memorial Aeronautical Laboratory, Massachusetts Institute of Technology, and McCook field. In addition to brief descriptions of the various wind tunnels and methods of testing, the report contains an analysis of the test data. It is shown that while in general the agreement is quite satisfactory there are two cases in which it is unsatisfactory. Since the lack of agreement in the latter is probably explained by errors known to be inherent in the methods of determining and applying corrections in these particular tests, it is concluded that the agreement obtained is more a matter of technique than a wind tunnel characteristic. (author)

Diehl, Walter S↗
NASA NTRS1985

Aeroelastic model helicopter rotor testing in the Langley TDT

Wind-tunnel testing of a properly scaled aeroelastic model helicopter rotor is considered a necessary phase in the design development of new or existing rotor systems. For this reason, extensive testing of aeroelastically scaled model rotors is done in the Transonic Dynamics Tunnel (TDT) located at the NASA Langley Research Center. A unique capability of this facility, which enables proper dynamic scaling, is the use of Freon as a test medium. A description of the TDT and a discussion of the benefits of using Freon as a test medium are presented. A description of the model test bed used, the Aeroelastic Rotor Experimental System (ARES), is also provided and examples of recent rotor tests are cited to illustrate the advantages and capabilities of aeroelastic model rotor testing in the TDT. The importance of proper dynamic scaling in identifying and solving rotorcraft aeroelastic problems, and the importance of aeroelastic testing of model rotor systems in the design of advanced rotor systems are demonstrated.

Mantay, W. R.↗
NASA NTRS2008

Supersonic Disk Gap Band Parachute Performance in the Wake of a Viking-Type Aeroshell from Mach 2 to 2.5

Supersonic wind tunnel testing of 0.813 m diameter Disk-Gap-Band parachutes is being conducted in the NASA Glenn Research Center (GRC) 10' x 10' wind-tunnel. The tests are conducted in support of the Mars Science Laboratory Parachute Decelerator System development and qualification. Four percent of full-scale parachutes were constructed similarly to the flight-article in material and construction techniques. The parachutes are attached to a 4% scale MSL entry-vehicle to simulate the free-flight configuration. The parachutes are tested from Mach 2 to 2.5 over a Reynolds number (Re) range of 1 to 3 x 10(exp 6), representative of the MSL deployment envelope. Constrained and unconstrained test configurations are investigated to quantify the effects of parachute trim, suspension line interaction, and alignment with the capsule wake. The parachute is constrained horizontally through the vent region, to measure canopy breathing and wake interaction for fixed trim angles of 0 and 10 degrees from the velocity vector. In the unconstrained configuration the parachute is permitted to trim and cone, similar to the free-flight varying its alignment relative to the entry-vehicle wake. Test diagnostics were chosen to quantify parachute performance and to provide insight into the flow field structure. An in-line load cell provided measurement of unsteady and mean drag as a function of Mach and Re. High-speed shadowgraph video of the upstream parachute flow field was used to capture bow-shock motion and stand of distance. Particle image velocimetry of the upstream parachute flow field provides spatially and temporally resolved measurement velocity and turbulent statistics. Multiple high speed video views of targets placed in the interior of the canopy enable photo-grammetric measurement of the fabric motion in time and space from reflective. High speed video is also used to document the supersonic inflation and measure trim angle, projected area, and frequency of area oscillations.

EDL↗
NASA NTRSDate not supplied

Additively Manufactured Wind Tunnel Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry descent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRS1975

Comparison of model and flight test data for an augmented jet flap STOL research aircraft

Aerodynamic design data for the Augmented Jet Flap STOL Research Aircraft or commonly known as the Augmentor-Wing Jet-STOL Research Aircraft was based on results of tests carried out on a large scale research model in the NASA Ames 40- by 80-Foot Wind Tunnel. Since the model differs in some respects from the aircraft, precise correlation between tunnel and flight test is not expected, however the major areas of confidence derived from the wind tunnel tests are delineated, and for the most part, tunnel results compare favorably with flight experience. In some areas the model tests were known to be nonrepresentative so that a degree of uncertainty remained: these areas of greater uncertainty are identified, and discussed in the light of subsequent flight tests.

Cook, W. L.↗
NASA NTRS1985

Rotary-balance experiments on a modern fighter aircraft configuration at high Reynolds numbers

NASA Ames Research Center's research program to investigate high-angle-of-attack aerodynamic phenomena associated with high-performance aircraft includes the development and use of rotary balance apparatuses for wind balance apparatuses for wind tunnel tests of airplane models in a coning motion. A large scale apparatus, developed for testing models at high Reynolds numbers in the Ames 12-Foot Pressure Wind Tunnel, was recently tested with an 0.05-scale F-15 fighter model. Measurements were made at low subsonic Mach numbers and chord Reynolds numbers of 1 to 5.5 million, with angles of attack from 0 to 90 deg and sideslip angles from -15 to +15 deg. Effects of Reynolds number, spin-rate parameter, model attitude, presence of a nose boom, and model/sting mounting angle were investigated.

Malcolm, G. N.↗
NASA NTRS1974

Static stability characteristics of the space shuttle external tank (MSFC model 458) during reentry in the MSFC 14-inch TWT (TA1F)

Data obtained in a wind tunnel test of a 0.003-scale modified MCR 0200 space shuttle external tank (ET) model tested at reentry conditions in the MSFC 14-inch trisonic wind tunnel are presented. This test is a continuation of a series of tests conducted to evaluate the aerodynamic characteristics of the ET during reentry. Three Mach numbers were investigated: 1.96, 3.48, and 4.96. The angle-of-attack range was -10 deg to 190 deg. Eight roll positions of the model from 0 deg to 315 deg were tested. The run schedule consisted of 162 runs. No. 120 grit was applied randomly over the model throughout the test.

Ramsey, P. E.↗
NASA NTRS1976

An investigation in the MSFC TWT to determine spoiler effects on wing loads and elevon hinge moments utilizing 0.004-scale models (77-0 and 74-OTS) of the shuttle vehicle 5 configuration (IA125)

Information is presented for wind tunnel tests (IA125) of a 0.004-scale orbiter, external tank, and solid rocket motor integrated vehicle model (77-0 and 74-OTS) in the MSFC Trisonic Wind Tunnel. These tests were conducted in support of MCR's 1344 and 1346. Data from these tests provide spoiler effects on wing bending/torsion and elevon hinge moments, elevon effectiveness data and the influence of solid plumes from Mach numbers of 0.6 through 2.74 at angles of attack and sideslip from -10 through 10 degrees.

Allen, E. C.↗
NASA NTRS1978

Comparison of nozzle and afterbody surface pressures from wind tunnel and flight test of the YF-17 aircraft

Results are reported from the initial phase of an effort to provide an adequate technical capability to accurately predict the full scale, flight vehicle, nozzle-afterbody performance of future aircraft based on partial scale, wind tunnel testing. The primary emphasis of this initial effort is to assess the current capability and identify the cause of limitations on this capability. A direct comparison of surface pressure data is made between the results from an 0.1-scale model wind tunnel investigation and a full-scale flight test program to evaluate the current subscale testing techniques. These data were acquired at Mach numbers 0.6, 0.8, 0.9, 1.2, and 1.5 on four nozzle configurations at various vehicle pitch attitudes. Support system interference increments were also documented during the wind tunnel investigation. In general, the results presented indicate a good agreement in trend and level of the surface pressures when corrective increments are applied for known effects and surface differences between the two articles under investigation.

Lucas, E. J.↗
NASA NTRS1981

A large-scale investigation of engine influence on inlet performance at angle-of-attack

A low-speed wind tunnel test was conducted in the NASA/Ames 40-x-80-foot wind tunnel to investigate the effect of engine/inlet flowfield interaction on inlet performance near flow separation. The effect of engine/inlet flowfield interaction was determined by comparing the performance of a large-scale subsonic inlet (CR = 1.26) close-coupled and remote-coupled to a TF-34 turbofan engine. The remote coupled inlet configuration removes the influence of the engine on the inlet flowfield and further, typifies conventional small-scale inlet test techniques which generally provide no simulation of turbomachinery effects. Test results indicated that engine interaction allows the inlet to operate with lower distortion levels at and beyond the separation angle-of-attack attained without engine interaction.

Hodder, B. K.↗
NASA NTRS1976

Results of investigations conducted in the LaRC 8-foot transonic pressure tunnel using the 0.010-scale 72-OTS model of the space shuttle integrated vehicle (IA93)

Test procedures, history, and data from the wind tunnel test are presented. Aero-loads were investigated on the updated configuration-5 space shuttle launch vehicle at Mach numbers from 0.600 to 1.205. Six-component vehicle forces and moments, base and sting-cavity pressures, elevon hinge moments, wing-root bending and torsion moments, and normal shear force data were obtained. Full simulation of updated vehicle protuberances and attach hardware was employed. Various elevon deflection angles were tested with two different forward orbiter-to-external-tank attach-strut configurations. The entire model was supported by means of a balance mounted in the orbiter through its base and suspended from a sting.

Nichols, M. E.↗
NASA NTRS1971

Space shuttle: Verification of booster transition characteristics for transonic and supersonic Mach numbers (M equals 0.6 - 5.0)

The results of the booster verification wind tunnel test are presented. These tests were conducted in a 14 x 14-inch trisonic wind tunnel utilizing a .0035 scale model. The nominal Mach numbers tested were 0.6, 0.9, 0.95, 1.0, 1.05, 1.20, 1.50, 2.0, 2.74, 3.00, 4.50 and 5.0. The angle of attack range was +5 to 40 deg. The yaw data was obtained over a range of -10 to +10 deg at fixed angles of attack of 0, 6, 15, 25, and 30 deg. The Reynolds number range was 4.2 to 6.9 million per foot. Results include elevon and canard effectiveness in pitch, and rudder, aileron, body flap, and tail effectiveness in yaw.

Carter, W. V.↗
NASA NTRS2011

Open Rotor - Analysis of Diagnostic Data

NASA is researching open rotor propulsion as part of its technology research and development plan for addressing the subsonic transport aircraft noise, emission and fuel burn goals. The low-speed wind tunnel test for investigating the aerodynamic and acoustic performance of a benchmark blade set at the approach and takeoff conditions has recently concluded. A high-speed wind tunnel diagnostic test campaign has begun to investigate the performance of this benchmark open rotor blade set at the cruise condition. Databases from both speed regimes will comprise a comprehensive collection of benchmark open rotor data for use in assessing/validating aerodynamic and noise prediction tools (component & system level) as well as providing insights into the physics of open rotors to help guide the development of quieter open rotors.

Envia, Edmane↗
NASA NTRS2006

Advances in Measurement of Skin Friction in Airflow

The surface interferometric skin-friction (SISF) measurement system is an instrument for determining the distribution of surface shear stress (skin friction) on a wind-tunnel model. The SISF system utilizes the established oil-film interference method, along with advanced image-data-processing techniques and mathematical models that express the relationship between interferograms and skin friction, to determine the distribution of skin friction over an observed region of the surface of a model during a single wind-tunnel test. In the oil-film interference method, a wind-tunnel model is coated with a thin film of oil of known viscosity and is illuminated with quasi-monochromatic, collimated light, typically from a mercury lamp. The light reflected from the outer surface of the oil film interferes with the light reflected from the oil-covered surface of the model. In the present version of the oil-film interference method, a camera captures an image of the illuminated model and the image in the camera is modulated by the interference pattern. The interference pattern depends on the oil-thickness distribution on the observed surface, and this distribution can be extracted through analysis of the image acquired by the camera. The oil-film technique is augmented by a tracer technique for observing the streamline pattern. To make the streamlines visible, small dots of fluorescentchalk/oil mixture are placed on the model just before a test. During the test, the chalk particles are embedded in the oil flow and produce chalk streaks that mark the streamlines. The instantaneous rate of thinning of the oil film at a given position on the surface of the model can be expressed as a function of the instantaneous thickness, the skin-friction distribution on the surface, and the streamline pattern on the surface; the functional relationship is expressed by a mathematical model that is nonlinear in the oil-film thickness and is known simply as the thin-oil-film equation. From the image data acquired as described, the time-dependent oil-thickness distribution and streamline pattern are extracted and by inversion of the thin-oil-film equation it is then possible to determine the skin-friction distribution. In addition to a quasi-monochromatic light source, the SISF system includes a beam splitter and two video cameras equipped with filters for observing the same area on a model in different wavelength ranges, plus a frame grabber and a computer for digitizing the video images and processing the image data. One video camera acquires the interference pattern in a narrow wavelength range of the quasi-monochromatic source. The other video camera acquires the streamline image of fluorescence from the chalk in a nearby but wider wavelength range. The interference- pattern and fluorescence images are digitized, and the resulting data are processed by an algorithm that inverts the thin-oil-film equation to find the skin-friction distribution.

Brown, James L.↗
NASA NTRSDate not supplied

Additively Manufactured Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry decent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRS1993

Performance results from a test of an S-76 rotor in the NASA Ames 80- by 120-foot wind tunnel

A full-scale helicopter rotor wind tunnel test has been conducted which covers a wide range of rotor-shaft angles-of-attack and 0-100 kt thrust conditions. The hover performance data thus obtained were compared with the results of momentum theory calculations; forward flight rotor-performance data were compared with calculations from a comprehensive rotorcraft analysis. These comparisons suggest that hover testing at an outdoor facility in the absence of ground effect is required to make a final determination of the absolute accuracy of the wind tunnel hover data.

Shinoda, Patrick M.↗