Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structural material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Quantifying the effects of artificial aging on the ignition and self-propagating reactions of Ni(V)/Al multilayers

Bimetallic, reactive multilayers are uniformly structured materials composed of alternating nanoscale layers that may be ignited to produce self-propagating intermetallic-formation reactions. When reactive multilayers age, there is a change in local composition and loss of stored chemical energy due to mass transport and rearrangement at the interfaces. Here, to quantify the long-term reliability of commercial Ni(V)/Al multilayers, the effects of accelerated aging on both ignition sensitivity and self-propagating reactions have been examined. Thermally aged samples were characterized using transmission electron microscopy, differential scanning calorimetry, and laser ignition combined with high-speed videography. The analytically quantifiable nature of both continuous wave laser ignition and reactive wave propagation enabled calculations of Arrhenius rate constants for as-received and various heat-treated multilayers. With heat treatment, there is a change in the intermixed thickness and interfacial chemistry that decreases the activation energy for point ignition but increases it for self-propagating reactions. This finding implies that with increased thermal aging, the reaction becomes easier to facilitate in the solid state but harder in the liquid phase.

Energetic material↗
DOE OSTI2026

Bayesian discovery of optimal reduced order models from mechanistic and experimental data: A case study of Pd penetration in TRISO fuels using BISON

TRistructural ISOtropic (TRISO) particles rely on a silicon carbide (SiC) layer as the primary structural material and barrier to metallic fission products (FPs) release. Accurate prediction of palladium (Pd) transport and penetration is therefore critical for qualifying TRISO fuels for advanced reactors. The empirical correlation for Pd penetration in BISON is derived from historical particle-fuel data, but cannot explain the large scatter in the experimental data that arises from varying experimental conditions. To aid fuel qualification, we previously developed a mechanistic reduced order model (ROM) using BISON that resolves these dependencies. Here, in this work we build on that mechanistic ROM and perform validation and quantify its uncertainty using Bayesian uncertainty quantification (UQ). calibration against a suite of in-pile and out-of-pile experiments spanning particle compositions, geometries, and operating conditions, and we benchmark it against the empirical correlation. Bayesian UQ identifies influential parameters, calibrates them to data, and yields predictive intervals. Results show that while the empirical correlation can be tuned to fit a single experiment type, it transfers poorly; the mechanistic ROM sustains accuracy with credible uncertainty across disparate conditions. This demonstrates a practical path—via Bayesian UQ applied to mechanistic ROMs—to leverage single-effect experiments for inferring in-reactor behavior and supporting TRISO fuel qualification.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Substitution of virgin carbon fiber with low-cost recycled fiber in automotive grade injection molding polyamide 66 for equivalent composite mechanical performance with improved sustainability

Recycled carbon fiber has historically proven challenging to integrate into composite manufacturing due in no small part to the low-density, randomly oriented, discontinuous fiber format that results from typical recycling. Discontinuous fiber requires the use of alternative technologies than those traditionally applied to continuous fiber (e.g., hand lay-up, winding). Extrusion compounding is one such applicable technology, but material transfer into the system requires alternative feeding equipment or the use of an altered procedure as trialed in this research. In this study, an injection molding compound for automotive applications was prepared with recycled carbon fiber and compared against an existing commercial compound. Input fibers and molded compound were evaluated for mechanical performance, while relevant variables such as compounded fiber alignment and aspect ratio were compared to the existing baseline material to confirm a like-for-like composite material structure. Overall, analysis indicates that recycled fiber performs similarly to virgin fiber reinforcement, demonstrating that recycled fiber may be a viable drop-in replacement for short-fiber discontinuous applications.

42 ENGINEERING↗
DOE OSTI2023

Economic competitiveness of pultruded fiber composites for wind turbine applications

Pultrusion manufacturing of fiber reinforced polymers has been shown to yield some of the highest mechanical properties for unidirectional composites, having a high degree of fiber alignment with consistent performance. Pultrusions offer a low-cost manufacturing approach for producing unidirectional composites with a constant cross-section and are used in many applications, including spar caps of wind turbine blades. However, as an intermediate processing step for wind blades, the additional cost of manufacturing pultrusions must be accompanied by sufficient increases in mechanical performance and system benefits. Wind turbine blades are manufactured using vacuum-assisted resin transfer molding with infused unidirectional fiberglass or carbon pultrusions for the spar cap. Infused fiberglass composites are among the most cost-effective structural materials available and replacing this material in the cost-driven wind industry has proven challenging, where infused fiberglass spar caps are still the predominant material system in use. To evaluate alternative material systems in a pultruded composite form, it is necessary to understand the costs for this additional manufacturing step which are shown to add 33%–55% on top of the material costs. A pultrusion cost model has been developed and used to quantify cost sensitivities to various processing parameters. The mechanical performance for pultruded composites is improved versus resin-infusion manufacturing with a 17% increase in design strength at a constant fiber volume fraction, but also enables higher achievable fiber volume fractions. The cost-specific mechanical performance is compared as a function of processing parameters for pultruded composites to identify the opportunities for alternative material and manufacturing approaches for wind turbine spar caps. Finally, four materials are compared in a representative wind turbine blade model to assess the performance of pultruded carbon fiber systems and pultruded fiberglass relative to infused fiberglass, where the pultruded systems produce lower weight blades with various cost distinctions.

42 ENGINEERING↗
DOE OSTI2023

Effect of pressure on high-temperature oxidation of Ni alloys in supercritical CO 2 containing impurities

Direct supercritical CO 2 (sCO 2 ) power cycles require structural materials compatible with hot sCO 2 containing high levels of water and oxygen impurities. Chromia-forming Ni-based superalloys, which are leading candidates at temperatures > 600 °C, have shown good compatibility in pure sCO 2 , however potential impurity effects are not well understood. In this report we exposed several commercial Ni-based alloys to 95%CO 2 -4%H 2 O-(1-3)%O 2 at 750 °C and 0.1 or 20 MPa for 2500 h. Protective chromia scales formed in all cases. Nevertheless, water vapor-assisted oxide volatilization clearly occurred at high pressure. The volatilization rates decreased with time, but still represent a potentially serious compatibility issue in real, high-velocity, sCO 2 systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Historic and modern nuclear graphite impurities: Pathways to improved waste strategies

Graphite has been used in large volumes as a structural material and neutron moderator since the earliest days of nuclear fission. However, no international consensus exists on the disposal of irradiated graphite, leaving much of the historic radioactive graphite inventory in interim vault or silo storage. With several new graphite-moderated reactors planned or under construction, the issue of graphite waste management is becoming increasingly urgent. This paper reviews and quantifies impurities in both historic and modern nuclear graphite, with emphasis on nitrogen—responsible for much of the 14 C inventory—and chlorine, which plays a critical role in repository performance and design. Modern graphites, benefitting from stringent quality-control measures developed for non-nuclear industries, meet or exceed the ASTM Ultra-High Purity nuclear standards, even without halide purification. Both chlorine and nitrogen concentrations have declined over time. For chlorine, identified as a key impurity influencing U.S. waste repository design, we propose a target of 0.1 appm in as-fabricated billets as a reasonable benchmark. Nitrogen sources are traced throughout the graphite production process, with surface and bulk concentrations characterized for all materials studied. Modern graphites commonly exhibit nitrogen levels below 5 appm, with values approaching 1 appm achievable. Using such reduced-nitrogen grades is critical to keeping graphite-induced radioactivity below the greater-than-Class-C waste threshold, thereby avoiding disposal cost penalties of nearly an order of magnitude.

Chlorine↗
DOE OSTI2023

High-temperature chromium diffusion in austenitic stainless steel: Ab initio molecular dynamics simulations

Chromium self-diffusion through stainless steel (SS) matrix and along grain boundaries is an important mechanism controlling SS structural materials corrosion. For this work, Cr diffusion in austenitic SS was simulated using canonical ab initio molecular dynamics with realistic models of type-316 SS bulk, with and without Cr vacancies, and a low-energy Σ3 twin boundary typically observed at active corrosion sites. Cr self-diffusion coefficients at 750 and 850 °C calculated using Einstein’s diffusion equation are 4.2 × 10 –6 and 8.1 × 10 –6 Å 2 ps –1 in pristine bulk, 3.8 × 10 –3 and 5.5 × 10 –3 Å 2 ps –1 in bulk including Cr vacancies, and 9.5 × 10 –2 and 1.0 × 10 –1 Å 2 ps –1 at a Σ3[1 1 1]60° twin boundary.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of strain rate on the deformation of hollow CoS nanoboxes and doubly porous self-assembled films

Nanomaterials with multiscale porosity are attractive as lightweight structural materials because unique deformation mechanisms can be programmed at different length scales. Here, we explore this concept by investigating the mechanics of hollow nanoboxes, as well as films self-assembled from nanoboxes. Hollow CoS nanoboxes with lengths of 900 nm and <30 nm wall thickness are synthesized using colloidal methods. Individual nanoboxes are compressed inside a scanning electron microscope at strain rates of 0.001 s –1 , 0.01 s –1 , and 0.1 s –1 . Nanoboxes are found to have a first peak stress of 15 MPa and loading modulus of ~240 MPa regardless of strain rate. The nanoboxes deform through ductile, plastic bending of side walls at 0.001 s –1 strain rate, while brittle fracture occurs at the higher strain rates. Self-assembly of these nanoboxes results in films with relative density of <0.1. Nanoindentation shows strain rate independent behavior with average modulus and hardness of ~15 MPa and ~230 kPa, respectively. Furthermore, the mechanical behavior of the film is compared to that of the nanobox building blocks, cellular foams and granular materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Liquid hydrogen storage system for heavy duty trucks: Configuration, performance, cost, and safety

In this work, we investigate the potential of liquid hydrogen storage (LH 2 ) on-board Class-8 heavy duty trucks to resolve many of the range, weight, volume, refueling time and cost issues associated with 350 or 700-bar compressed H 2 storage in Type-3 or Type-4 composite tanks. We present and discuss conceptual storage system configurations capable of supplying H 2 to fuel cells at 5-bar with or without on-board LH 2 pumps. Structural aspects of storing LH 2 in double walled, vacuum insulated, and low-pressure Type-1 tanks are investigated. Structural materials and insulation methods are discussed for service at cryogenic temperatures and mitigation of heat leak to prevent LH 2 boiloff. Failure modes of the liner and shell are identified and analyzed using the regulatory codes and detailed finite element (FE) methods. The conceptual systems are subjected to a Failure modes and effects analysis (FMEA) and a safety, codes, and standards (SCS) review to rank failures and identify safety gaps. The results indicate that the conceptual systems can reach 19.6% usable gravimetric capacity, 40.9 g-H 2 /L usable volumetric capacity and $174-183/kg-H 2 cost (2016 USD) when manufactured 100,000 systems annually.

08 HYDROGEN↗
DOE OSTI2021

Large rotations of the grain-scale stress tensor during yielding set the stage for failure

The stress-state within individual grains in a polycrystal determine the fate of the aggregate including mechanical failure. By tracking the evolution of the stress tensor throughout the elastoplastic transition, large rotations of the stress-state, which have long been theorized to occur, are observed experimentally for the first time. These stress rotations (~15°) are more than an order of magnitude larger than the concomitant crystallographic lattice reorientations (~0.9°) well-known to occur during metal plasticity. Furthermore, these rotations are accompanied by a decrease in stress triaxiality within certain grains, promote strain softening, and set the stage for failure at an early stage of deformation. Finally, these results provide a completely new perspective through which to contemplate the question of “hot-spots” responsible for failure of high-performance structural materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of phase-transformation path in TiZrHf(VNbTa)x refractory high-entropy alloys and its effect on mechanical property

Refractory high-entropy alloys (RHEAs) show a great potential as structural materials due to their remarkable properties, such as high strength and thermal stability. Despite these advantages, the RHEAs still suffer from the limited ductility at room temperature. To overcome the strength-ductility trade-off, the new RHEA design strategy, transformation-induced plasticity (TRIP) HEAs, have been developed by applying metastability-engineering approach. With the newly developed RHEAs design strategy, we designed metastable RHEAs, TiZrHfVxNbxTax (x = 1.0, 0.5 and 0.1) with decrease of the β-stabilizing elements (V, Nb, and Ta) to promote the transformation-induced ductility and work-hardening capability. The proper addition of the β-stabilizing elements (V, Nb, and Ta) into the ternary equi-molar TiZrHf alloy (TiZrHfV 0.1 Nb 0.1 Ta 0.1 ) leads to stress/strain-induced phase transformation from the body-centered cubic (BCC) to hexagonal-close-packed (HCP) α' and/or orthorhombic α" phases. Here, detailed studies on the phase transformation sequence during the deformation were carried out using X-ray diffraction (XRD), electron back-scattered diffraction (EBSD), and transmission-electron microscope (TEM), which revealed the stepwise phase transformation that is responsible for the strong strain hardening behavior. Furthermore, we further suggested the new transformation-induced-plasticity (TRIP) HEA design strategy, applying the Bo-Md approach.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Intermetallic phase formation in Al-Si-Zr alloys during hot isostatic pressing revealed by experiments and molecular dynamics

Understanding phase transformations at alloy interfaces is critical for the design of advanced structural materials. Here, in this study, we investigate the formation mechanisms of the Al 2 SiZr intermetallic phase in the Al-Si-Zr system under hot isostatic pressing (HIP) using molecular dynamics (MD) simulations and thermodynamic analysis. A unique aspect of our approach in MD involves the replacement of a disordered Al 2 SiZr stoichiometry with an ordered phase at the Al-Zr interface once HIP results in the desired Al 2 SiZr stoichiometry, allowing us to compute the total energetic cost of transformation by accounting for both formation energies and diffusion barriers. Diffusion coefficients and activation energies, extracted across a range of temperatures, reveal that HIP substantially enhances atomic mobility, creating favorable stoichiometry for phase evolution. Our results show that Al 2 SiZr phase formation is kinetically unfavorable at lower temperatures but becomes feasible when the thermodynamic driving energy surpass a critical energy threshold.

Roy, Ankit [Pacific Northwest National Laboratory ↗
DOE OSTI2025

Extending wire-arc directed energy deposition using non-gravity aligned (NGA) torch methods

For standard Additive Manufacturing (AM) processes, traditional path planning typically relies on a 2.5-dimensional approach. In wire-arc directed energy deposition (DED), commonly referred to as wire-arc additive manufacturing (WAAM), this 2.5D approach inherently limits final near net shape due to the stair-step effect and restricts the maximum overhang angle achievable without part degradation. To achieve better near net shape and part quality, a 3D planning approach that modulates the tool tip position and angle without process changes is demonstrated in components containing up to 105° of unsupported overhang. The experimental methods are validated with half and fully enclosed cylinder sections containing 90° of overhang. The non-gravity aligned methods are then applied to a commercial WAAM system for a composite tool mold demonstrator part. As a result, the methods developed in this paper enable expansion of WAAM system capabilities to parts containing large overhangs without compromising the net shape or material structure of the resulting parts and without the need for a part positioner.

Additive manufacturing↗
DOE OSTI2026

Understanding failure in austenitic steels: Key considerations for molten salt storage in CSP applications

Owing to their excellent properties, austenitic stainless steels are extensively used in boilers, furnaces, molten salt tanks, and other applications that are subjected to extreme mechanical loads and high-temperature conditions. Their high corrosion and creep resistance make them suitable for high-temperature operating environments. Additionally, good fatigue resistance and favorable mechanical and visual properties are essential. However, the premature failure of several components at elevated temperatures has been previously reported. Although the failure analysis of components in service is complex, processes such as cold work and welding have been identified as contributing factors to the performance degradation of these steels. This study aims to analyze the various documented failure modes and mechanisms in austenitic steels, including creep, cracking, stress relaxation cracking, and fatigue, to better understand the multi-objective design requirements for these alloys as structural materials for high-temperature molten salt tanks in Concentrating Solar Power (CSP) plants. Stabilized austenitic grades, such as AISI 347H, demonstrate superior resistance to creep and corrosion-related degradation when compared to non-stabilized grades like AISI 316L at temperatures relevant to concentrated solar power (CSP) applications. In contrast, nickel-based alloys offer enhanced corrosion resistance, albeit at a higher cost. This review underscores that creep, stress relaxation cracking, and thermo-mechanical fatigue are the predominant long-term failure risks in CSP hot tanks.

14 SOLAR ENERGY↗
DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗
DOE OSTI2020

Method for identification of redox control parameters for corrosion mitigation in molten fluoride salts

Structural material corrosion is a significant concern for the development of molten salt-cooled reactors (MSR) and redox control was proposed to mitigate the corrosion. This study presents an efficient approach to identify the partial pressure of F 2 gas for fluorine driven corrosion, the concentration ratios of UF 4 /UF 3 and ZrF 4 /ZrF 2 , and the partial pressure ratio of HF/H 2 needed to limit metal corrosion and its subsequent dissolution in molten fluoride salts. The identification procedure is made by simply using auxiliary axes in Ellingham diagrams. This approach greatly simplifies the optimization of redox control methods in studying the material corrosion in molten salts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of stacking fault energy on damage microstructure in ion-irradiated CoCrFeNiMn concentrated solid solution alloys

In order to understand the effect of stacking fault energy on microstructural evolution in concentrated solid solution alloys, Kr 2+ ion irradiation was performed for FCC-type CoCrFeNiMnx alloys. During Kr 2+ ion irradiation at 500 degrees C the formation of black dots, self-interstitial atom faulted loops and perfect loops were observed, but no observable voids were found in all the alloys. The comparison of microstructural evolution among CoCrFeNiMn x (x = 0.7, 1, 1.3) alloys revealed less faulted loop number density and size in CoCrFeNiMn 1.3 . The stacking fault energy of each alloy was investigated using the deformed CoCrFeNiMn x alloys, and it was revealed that CoCrFeNiMn 1.3 had the highest stacking fault energy, which is higher value than that of 316SS. From these results, it is suggested that FeCrNiMn-based concentrated solid solution alloys could be well-designed by controlling the stacking fault energy with optimized Mn concentration as one of high radiation resistance structure materials. (C) 2020 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗