Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “soil depth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Assimilation of Vegetation Optical Depth Retrievals from Passive Microwave Radiometry

Vegetation optical depth (VOD) retrievals from passive microwave sensors provide analog estimates of above-ground canopy biomass. This study presents the development and analysis of assimilating VOD retrievals from X-, C-, and L-band passive microwave instruments within the Noah-MP land surface model over the Continental U.S. The results from this study demonstrate that the assimilation of VOD retrievals have a significant beneficial impact on the simulation of evapotranspiration and GPP, particularly over the agricultural areas of the U.S. The improvements in the water and carbon fluxes from the assimilation of VOD from X- and C-band sensors are found to be comparable to those obtained from the assimilation of vegetation indices from optical sensors.The study also quantifies the relative and joint impact of assimilating surface soil moisture and VOD from the Soil Moisture Active Passive (SMAP) mission. The utility of soil moisture assimilation for improving ET is more significant over water-limited regions, whereas VOD DA is more impactful over areas where soil moisture is not the primary controlling factor on ET. The results also indicate that the information on moisture and vegetation states from SMAP can be simultaneously exploited through the joint assimilation of surface soil moisture and VOD. Since passive microwave-based VOD retrievals are available in nearly all weather conditions, their use within data assimilation systems offers the ability to extend and improve the utility obtained from the use of optical/infrared based vegetation retrievals

Sujay V Kumar↗
NASA NTRS2024

Parameterizing Spectral Surface Reflectance Relationships for the Dark Target Aerosol Algorithm Applied to A Geostationary Imager

Originally developed for the Moderate Resolution Imaging Spectroradiometer (MODIS) in polar, sun-synchronous low-earth orbit (LEO), the Dark Target (DT) aerosol retrieval algorithm relies on the assumption of a Surface Reflectance Parameterization (SRP) over land surfaces. Specifically for vegetated and dark-soiled surfaces, values of surface reflectance in blue and red visible-wavelength bands are assumed to be nearly linearly related to each other and to the value in a shortwave infrared (SWIR) wavelength band. This SRP also includes dependencies on scattering angle and a normalized difference vegetation index computed from two SWIR bands (NDVISWIR). As the DT retrieval algorithm is being ported to new sensors to continue and expand the aerosol data record, we assess whether the MODIS-assumed SRP can be used for these sensors. Here, we specifically assess SRP for the Advanced Baseline Imager (ABI) aboard, the Geostationary Operational Environmental Satellite (GOES)-16/East (ABIE). First, we find that using MODIS-based SRP leads to higher biases and artificial diurnal signatures in aerosol optical depth (AOD)retrievals from ABIE. The primary reason appears to be that geostationary orbit (GEO) encounters an entirely different set of observation geometry than does LEO, primarily with regards to solar angles coupled with fixed view angles. Therefore, we have developed a new SRP for GEO that draws the angular shape of the surface bidirectional reflectance. We also introduce modifications to the parametrization of both red-SWIR and blue-red spectral relationships to include additional information.The revised Red-SWIR SRP includes solar zenith angle, NDVISWIR, and land-type percentage from an ancillary database. The blue-red SRP adds dependencies on the scattering angle and NDVISWIR. The new SRPs improve the AOD retrieval of ABIE in terms of overall less bias and mitigation of the overestimation around local noon. The average bias of DT AOD compared to AERONET AOD shows a reduction from 0.08 to 0.03, while the bias of local solar noon decreases from 0.12 to 0.03.The agreement between DT and AERONET AOD is established through regression slope of 1.06 and y-intercept of 0.01with correlation coefficient is0.74. By using the new SRP, the percentage of data falling within the expected error range (±0.05 + 15%) is notably risen from 54% to 78%.

Mijin Kim↗
DOE OSTI2025

Code associated with "Assessing the Effect of a Deep-Rooted Grass on Belowground Carbon Storage in Cultivated Land: Insights from a Multi-Site US Study"

R code associated with "Assessing the Effect of a Deep-Rooted Grass on Belowground Carbon Storage in Cultivated Land: Insights from a Multi-Site US Study" These scripts can be used to analyze the accompanying dataset: https://doi.org/10.5281/zenodo.16620529. (1) resampling_functions.R : Creates functions for resampling data for nonparametric bootstrapping (2) bootstrap_depth_profiles.R : Applies resampling functions to the dataset (3) gapfill_masscalcs.R : Prepares data for equivalent mass calculations (4) get_14C_EM.R : Applies soilR to obtain the 14C end member for mixing model calculations (5) mass_aggregate.R : Performs equivalent mass and mass weighted averaging calculations.

Carbon↗
NASA NTRS1971

Bearing strength of lunar soil.

Bearing load vs penetration curves have been measured on a 1.3 g sample of lunar soil from the scoop of the Surveyor 3 soil mechanics surface sampler, using a circular indentor 2 mm in diameter. Measurements were made in an Earth laboratory, in air. This sample provided a unique opportunity to evaluate earlier, remotely controlled, in-situ measurements of lunar surface bearing properties. Bearing capacity, measured at a penetration equal to the indentor diameter, varied from 0.02-0.04 N/sq cm at bulk densities of 1.15 g/cu cm to 30-100 N/sq cm at 1.9 g/cu cm. Deformation was by compression directly below the indentor at bulk densities below 1.61 g/cu cm, by outward displacement at bulk densities over 1.62 g/cu cm. Preliminary comparison of in-situ remote measurements with those on returned material indicates good agreement if the lunar regolith at Surveyor 3 has a bulk density of 1.6 g/cu cm at 2.5 cm depth.

Jaffe, L. D.↗
NASA NTRS2004

Radio Sounding Techniques for the Galilean Icy Moons and their Jovian Magnetospheric Environment

Radio sounding of the Earth's topside ionosphere and magnetosphere is a proven technique from geospace missions such as the International Satellites for Ionospheric Studies (ISIS) and the Imager for Magnetopause-to-Aurora Global Exploration (IMAGE). Application of this technique to Jupiter's icy moons and the surrounding Jovian magnetosphere will provide unique remote sensing observations of the plasma and magnetic field environments and the subsurface conductivities, of Europa, Ganymede, and Callisto. Spatial structures of ionospheric plasma above the surfaces of the moons vary in response to magnetic-field perturbations from (1) magnetospheric plasma flows, (2) ionospheric currents from ionization of sputtered surface material, and (3) induced electric currents in salty subsurface oceans and from the plasma flows and ionospheric currents themselves. Radio sounding from 3 kHz to 10 MHz can provide the global electron densities necessary for the extraction of the oceanic current signals and supplements in-situ plasma and magnetic field measurements. While radio sounding requires high transmitter power for subsurface sounding, little power is needed to probe the electron density and magnetic field intensity near the spacecraft. For subsurface sounding, reflections occur at changes in the dielectric index, e.g., at the interfaces between two different phases of water or between water and soil. Variations in sub-surface conductivity of the icy moons can be investigated by radio sounding in the frequency range from 10 MHz to 50 MHz, allowing the determination of the presence of density and solid-liquid phase boundaries associated with oceans and related structures in overlying ice crusts. The detection of subsurface oceans underneath the icy crusts of the Jovian moons is one of the primary objectives of the Jupiter Icy Moons Orbiter (JIMO) mission. Preliminary modeling results show that return signals are clearly distinguishable be&een an ice crust with a thickness of 7 km on 1) an ocean and 2) a layer of bedrock. Knowledge of the ionospheric contributions to the time delay of the low-frequency subsurface radar is shown to be important in obtaining accurate depth information.

Green, James L.↗
DOE OSTI2020

Multi-model Hydroclimate Projections for the Alabama-Coosa-Tallapoosa River Basin in the Southeastern United States

Abstract This study uses a high-resolution, process-based modeling framework to assess the impacts of changing climate on water resources for the Alabama-Coosa-Tallapoosa River Basin in the southeastern United States. A 33-member ensemble of hydrologic projections was generated using 3 distributed hydrologic models (Precipitation-Runoff Modeling System, Variable Infiltration Capacity, and Distributed Hydrology Soil Vegetation Model) of different complexity. These hydrologic models were driven by dynamically downscaled and bias-corrected future climate simulations from 11 Coupled Model Intercomparison Project Phase 5 global climate models under Representative Concentration Pathway 8.5 emission scenario, with 40 years each in baseline (1966–2005) and future (2011–2050) periods. The hydroclimate response, in general, projects an increase in mean seasonal precipitation, runoff, and streamflow. The high and low flows are projected to increase and decrease, respectively, in general, suggesting increased likelihood of extreme rainfall events and intensification of the hydrologic cycle. The uncertainty associated with the ensemble hydroclimate response, analyzed through an analysis of variance technique, suggests that the choice of climate model is more critical than the choice of hydrologic model for the studied region. This study provides in-depth insights of hydroclimate response and associated uncertainties to support informed decisions by water resource managers.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Mn-53 profiles in four Apollo surface cores

Mn-53 data are presented for four Apollo cores with an emphasis on the past 10-to-the-7th-year history of these samples: (1) Core 15011 has excess Mn-53 down to a depth of at least 9 cm, which is probably due to the continuous addition of near-surface irradiated material. (2) The Mn-53 profile for 64002 above 12 cm is relatively flat and in excess of that calculated for a static core, which suggests that the upper part of this core was deposited rapidly about 2 m.y. ago. (3) Results for the Apollo 17 drill stem show a large excess of Mn-53 from at least 3 cm downwards. Some magnetic separates obtained from this core have very high Mn-53 activities, probably due to the presence of agglutinates that were recently irradiated very near the surface. (4) The Mn-53 content of the upper part of 74002 is similar to that of trench samples collected nearby and indicates that the gray, orange, and black soils at this site have been exposed together near the surface for at least the last 10 m.y.

Nishiizumi, K.↗
NASA NTRS1976

Gas interaction effects on lunar bonded particles and their implications

Results are reported for an experimental investigation of gas-interaction effects on different Apollo 11 and Apollo 12 lunar-soil samples containing bonded particles. In the experiments, lunar fines were exposed to pure O2, pure water vapor, HCl, NH3, N2, HCOOH, and CH3NH2, in order to observe whether bonded particles would separate. In addition, repeated gas adsorption/desorption measurements were performed to determine the nature and reactive properties of the particle surfaces, and surface areas were measured for comparison with analogous terrestrial samples to determine whether the surface areas of highly radiation-damaged particles were larger or smaller. It is found that N2 is apparently ineffective in separating bonded particles and that the ratio of Apollo 11 to Apollo 12 bonded particles separated by a particular gas exposure ranges from 2.5 to 3.0. Possible reasons for differences in material surface properties at the two Apollo sites are considered, and it is concluded that material from a certain depth at some other site was transported to the Apollo 12 site and mixed with the original material in recent years (considerably less than 2000 years ago).

Mukherjee, N. R.↗
DOE OSTI2021

Biogeochemistry of Pond B (Savannah River Site, South Carolina, USA): Water column and Sediments

Pond B at Savannah River Site (SRS, South Carolina) is a monomictic reservoir that received SRS R reactor cooling water from 1961–1964. Previous studies conducted between the 1980s–1990s on the water column and sediments of Pond B measured trace amounts of Pu (33 MBq 238Pu and 430 MBq 239,240Pu), 241Am, and 137Cs. Since then, the pond has been relatively isolated and the radionuclide concentrations have not been monitored over time. Herein, about 30 years after the last publication on Pond B, we are re-evaluating the geochemistry and radionuclide distribution within Pond B at five locations along a horizontal transect from the inlet to outlet. In addition, we are conducting the first analysis of the microbial community composition. This data package consists of water column measurements (1) using a multi-probe sonde, (2) plutonium isotopes and total concentrations, (3) total organic/inorganic carbon concentrations, (4) trace metals and major ions concentrations, and (6) microbial community composition. Sediment measurements include (1) plutonium isotopes and total concentrations and (2) microbial community composition.For sediment core and porewater, please see other Pond B data package (ess-dive-60d2352a4495472-20200615T203925174).The data in this package will be submitted for peer review in 2023.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Cathodic Protection Modeling for Hanford Underground Double-Shell Tank Farms

Hanford stores millions of gallons of radioactive and chemically hazardous waste from the production of weapon materials in tank farms consisting of underground carbon-steel storage tanks surrounded by reinforced concrete. Six of these Hanford tank farms use double-shell storage tanks (DSTs). The DST farms were constructed from 1968 to 1986 with a planned 40–50 year design life, so some are already operating beyond their initial life expectancy. Ultrasonic testing (UT) has indicated significant thinning on the bottom of the secondary (outer) liner of these tanks, believed to arise from groundwater intrusion driving concrete side corrosion. There is no direct access to the steel/concrete interface between the tank and the concrete pad, making it difficult to apply a chemical-based mitigation strategy or to conduct repairs, but cathodic protection (CP) is a possible method to inhibit further concrete-side corrosion. Hanford already uses CP to protect below grade steel piping within the tank farms and connected to the tanks, but this system was not designed to protect the tank bottoms. CP design must account for the structures surrounding the DSTs, including the steel reinforcing bars (rebar) within the concrete pad and vault, various process lines, and the existing CP system. In this study, finite element analysis (FEA) modeling was carried out to simulate CP protection of 1) a single tank and CP anode to develop options for modeling the rebar and to compare to a simpler circuit model and 2) the entire Hanford AN tank farm as a representative example consisting of seven tanks, associated piping, and both existing and new CP anodes. Both circuit and FEA models predict that significant protective current could be delivered to the bottoms of the tanks with the addition of tank-protection anodes below the depth of the tanks. Simulations with only the existing pipe-protection anodes active confirmed that only a very small current to the tank bottoms is predicted under present conditions. Multiple simplified representations of the dome and wall rebar were tested to reduce the computational complexity of the tank-farm simulations, resulting in modeling the rebar as edge elements with a prescribed effective circumference that matches the real rebar surface area. The geometry of the rebar is also simplified into horizontal hoops around the tank walls and radial rebar over the dome with increased effective circumference to retain the target surface area. This simplification was found to greatly reduce the complexity and solution time of the models without large changes in current distributions, especially to the tank bottom. A range of values were tested for model parameters such as soil and concrete resistivities and polarization resistance to investigate their impact on the current and electric potential distributions. Depending on the parameters used, FEA simulations predict some risk of overprotection, particularly on the piping system; since overprotection can also lead to surface damage associated with hydrogen gas generation at the interface (e.g. hydrogen embrittlement or damage to coatings), this needs to be considered when refining the design of the new CP system. Comparison between the FEA models and the circuit model representation demonstrated that the circuit model could not match the predicted FEA current distribution, even when using the exact same surface areas. This discrepancy appeared to be at least partly attributable to the impact of the relative positions of the tank components and anodes to each other and to the ground surface. The FEA model accounts for the relative positions since it solves the governing equations in three dimensions, but the circuit model cannot account for the positioning. In particular, the circuit model underpredicts the current to the tank bottom and overpredicts the current to the dome compared to FEA for the baseline geometry. The FEA models omitted the electrically isolated rebar in the bottom concrete slab. However, a circuit based stray current model estimated that only 2.1% of the total current through the slab would stray into the rebar, corresponding to ~0.21 A for a target current density of 2 mA/ft2 to the tank bottom. The estimated corrosion driven by this amount of stray current is predicted to yield a lifetime of >400 years for the minimum rebar diameter, assuming an acceptable cross-section area loss of 10%.

d'Entremont, Anna [Savannah River National Laborat↗
DOE OSTI2025

Molecular Imaging of Microbially Induced Corrosion of Synthetic Archeological Glasses by a Rhizosphere Bacterium

Microbially induced corrosion (MIC) focuses on the degradation of solid materials, such as glass or metal. Soil microbes are often associated with the corrosion of foreign objects in the rhizosphere. Paenibacillus polymyxa SCE2, a facultative anaerobic bacterium in soil, is of the same genus as bacteria found near nuclear waste disposal sites. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used for imaging surface changes induced by P. polymyxa SCE2 cultured on two synthetic glass coupons to represent natural analogs of materials that were studied in relation to the vitrification of nuclear waste. Multimodal imaging was used to verify bacterial coverage across the glass surface after long-term growth. ToF-SIMS spectral analysis showed detection of glass component ions, such as silicon oxide (m/z – 59.96 SiO 2 – ) and aluminum oxide (m/z – 101.95 Al 2 O 3 – ), and biofilm’s extracellular polymeric substance (EPS) components, such as pentadecanoic acid (m/z – 241.22 C 15 H 29 O 2 – ) and sterol lipids (m/z – 311.16 C 20 H 23 O 3 – ). ToF-SIMS spectral, imaging, and depth profiling analyses showed that the glass rich in silica and other light elements (“granite glass”) had more “corrosion related” peaks than the glass that was less silica-rich and contained more iron (“dike glass”). Furthermore, these surface and interface compositional and spatial differences observed in the mass spectra and imaging were attributed to bacterial metabolism and an electron transfer mechanism influenced by morphological and compositional differences between the two types of glasses. ToF-SIMS is effective in studying microbial effects, bringing new molecular insights into MIC in a broader context of materials degradation.

Amorphous materials↗
NASA NTRS2000

Mars Greenhouse Experiment Module: An Experiment to Grow Flowers on Mars

NASA has entered a new phase of in-depth exploration of the planets where robotic exploration of the Solar System is focusing on in-situ missions that pave the way for human exploration. Creating a human presence on Mars will require specialized knowledge and experience concerning the Martian environment and validated technologies that will provide life-supporting consumables. An understanding of the response of terrestrial organisms to the Martian environment with respect to potential deleterious effects on crew health and changes to biological processes will be paramount. In response to these challenges an innovative selfcontained flight experiment is proposed, which is designed to assess the biocompatibility of the Martian environment by germinating seeds and following their growth through to flowering. The experiment, dubbed Mars Greenhouse Experiment Module (Mars GEM), will be accomplished in a sealed pressurized growth chamber or 'Mars Greenhouse'. Seeds will be grown in Martian soil and the Mars Greenhouse will provide ultraviolet-radiation protected, thermal-controlled environment for plant growth that actively controls the CO2 (required nutrient) and O2 (generated by the plants) levels in the chamber. The simple, but visually dramatic, demonstration of the potential to grow a plant in a man-made environment on the surface of Mars should establish a strong connection between current robotic missions and future human habitation on Mars.

MacCallum, T. K.↗
DOE OSTI2025

Old Woman Creek Wetland Sediment and Electrochemical Sensor Microbial Community, 2023

We are developing a technique to monitor microbiological activities referred to as zero resistance ammetry, which entails the deployment of graphite electrodes in sediments. Measurement of current between electrodes of contrasting redox regimes and/or predominant terminal electron accepting processes can be used as an indicator of the extents of microbiological activity. We deployed an electrode array at depths of 2 mm, 4 mm, 76 mm, 78 mm, 152 mm, 154 mm, 227 mm, and 229 mm below the wetland sediment water interface in the Old Woman Creek National Estuarine Research Center, Huron, OH, USA (Lat. = 41.380833, Long. = -82.508889). A core was collected from adjacent sediment and subsamples were collected from depth intervals of 0 – 25 mm, 25 – 127 mm, 127 – 128 mm, and below 178 mm. To determine if the microbial communities attached to the electrodes were reflective of the adjacent sediment-associated microbial community, we conducted a 16S rRNA gene-based (V4 region) survey of these respective materials. This data package contains the results of these surveys, including metadata on the depths from which samples were collected (samples.csv), DNA extraction and sequencing information (OWC_DEPTH_AMPLICON_SEQUENCING_METADATA), sequence processing information (OWC_DEPTH_BIOINFORMATIC_METADATA.csv), an operational taxonomic unit (OTU) table (OWC_DEPTH_97OTUS_TABLE.csv), and nucleotide sequences of OTUs (OWC_DEPTH_97OTUS_SEQS.fasta). All files can be opened using a text-editing application. The fasta file is compatible with bioinformatics applications.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1991

A geochemical assessment of possible lunar ore formation

The Moon apparently formed without appreciable water or other relatively volatile materials. Interior concentrations of water or other volatile substances appear to be extremely low. On Earth, water is important to the genesis of nearly all types of ores. Thus, some have reasoned that only abundant elements would occur in ore concentrations. The definition and recognition of ores on the Moon challenge the imaginations and the terrestrial perceptions of ore bodies. Lunar ores included solar-wind soaked soils, which contain abundant but dilute H, C, N, and noble gases (including He-3). Oxygen must be mined; soils contain approximately 45 percent (wt). Mainstream processes of rock formation concentrated Si, Mg, Al, Fe, and Ca, and possibly Ti and Cr. The highland surface contains approximately 70 percent (wt) feldspar (mainly CaAl2Si2O8), which can be separated from some highland soils. Small fragments of dunite were collected; dunite may occur in walls and central peaks of some craters. Theoretical extensions of observations of lunar samples suggest that the Moon may have produced ores of trace elements. Some small fragments have trace-element concentrations 10(exp 4) times higher than the lunar average, indicating that effective geochemical separations occurred; processes included fractional crystallization, silicate immiscibility, vaporization and condensation, and sulfide metamorphism. Operations of these processes acting on indigenous materials and on meteoritic material in the regolith could have produced ores. Infalling carbonaceous meteorites and comets have added water and hydrocarbons that may have been cold-trapped. Vesicles in basalts, pyroclastic beads, and reported transient events suggest gag emission from the lunar interior; such gas might concentrate and transport rare elements. Large impacts may disperse ores or produce them through deposition of heat at depth and by vaporization and subsequent condensation. The main problem in assessing lunar resources is the ignorance about the largely unexplored Moon.

Haskin, Larry A.↗
NASA NTRS2004

Geochemical and Mineralogical Indicators for Aqueous Processes in Gusev Crater and on Meridiani Planum

The Athena Science Instrument Payload is providing geochemical and mineralogical information for determining the properties of rocks, soils, and outcrops at the Mars Exploration Rovers landing sites. These measurements indicate that a variety of aqueous processes as well as various degrees of alteration occurred at the two landing sites. Light-toned rocks around the Spirit landing site appear to have coatings or alteration rinds that may have resulted from limited aqueous alteration on the surfaces of basaltic rocks. Hematite and high Fe(III)lFe(total) occur at the surfaces of these rocks. High concentrations of elements highly mobile in water (i.e., S, Cl, and Br) occur in rock veins, vugs, and coatings and at the bottom of soil trenches in the "intercrater plains." One scenario for the formation of rock coatings or rinds and translocation of mobile elements is that water might have occurred briefly at the Martian surface during periods of high obliquity and thin films of water may have mobilized elements and altered the surfaces of rocks. Outcrops on the slopes of the Columbia Hills appear to be extensively altered as suggested by their relative "softness" (measured as resistance to abrasion) as compared to basalts on the adjacent plains, high Fe(III)lFe(total), iron mineralogy dominated by nanophase Fe(III) oxides and hematite, and high Br and CI concentrations beneath outcrop surfaces. These outcrops may have formed by the alteration of basaltic rocks and/or volcaniclastic materials by solutions that were rich in volatile elements (e.g., Br, CI, S). However, it is not clear whether aqueous alteration occurred at depth (e.g., metasomatism), by hydrothermal solutions (e.g., associated with volcanic or impact processes), by vapors rich in volcanic gases, or by low-temperature solutions. The occurrence of jarosite, hematite, and other sulfates (e.g., Mg sulfates) in Eagle and Endurance crater outcrops are strong indicators of aqueous processes at Meridiani Planum. These phases occur with siliciclastic materials in outcrops. Jarosite can only form by aqueous processes under very acidic conditions; e.g., acid sulfate weathering conditions resulting from the oxidation of Fe sulfides or by sulfuric acid alteration of basalts by solutions associated with S02-rich volcanic gases. It is plausible that acidic solutions rich in sulfur (and Fe(II)) reacted with basaltic sediments (which provided a host of soluble cations) under oxidizing conditions and then, through evaporation, formed sediments rich in jarosite and other sulfates along with siliciclastic materials. Hematite-rich spherules in outcrops may have formed by aqueous processes within the sedimentary layers, which promoted transport of Fe (II) solutions to nucleation sites where oxidation and precipitation occurred to form hematite-rich spherules.

Ming, Douglas W.↗
NASA NTRS2010

Support of Operation Icebrige Using the NASA P-3B Airborne Laboratory

The National Aeronautics and Space Administration (NASA) Wallops Flight Facility's (WFF) P-313 Orion is a medium-lift, four engine turbo-prop aircraft that has been reconfigured from a military aircraft to an Earth Science research platform. The aircraft has a long history of supporting science missions, flying on average over 200 hours per year. Examples of research missions that have been flown aboard the aircraft are remote sensing flights to study geophysical parameters including ice-sheet topography and periodic change, soil moisture content, and atmospheric aerosol constituents. Missions are conducted for the purposes of calibration/validation of various NASA and international satellites, including ICESat-1, that monitor climate change as well as process studies and the test of new prototype remote sensing instruments. Due to the recent demise of the NASA ICESat-1 spacecraft, NASA elected to fill the data void between it and the upcoming ICESat-2 using airborne measurements. This mission is called Operation Ice Bridge (OIB). These measurements are being made from a variety of aircraft, including the P-313. The aircraft is being using to conduct ice surveys of the Arctic, in particular Greenland. The aircraft has been conducting ice surveys of Greenland since 1993 for the purposes of topographic mapping of both the surface and basal topography; therefore, OIB is a natural fit for the aircraft and its crew. Additional measurements of snow depth and gravity have been made as part of OIB. This paper will provide an overview of the P-313 platform and highlight the support for Operation Ice Bridge.

Guillory, Anthony R.↗
DOE OSTI2022

Incorporating Microtopography in a Land Surface Model and Quantifying the Effect on the Carbon Cycle

Abstract Northern peatlands are a terrestrial carbon store, with an annual sink of 0.1 Pg C yr −1 and a total storage estimate of 547 Pg C. Northern peatlands are also major contributors of atmospheric methane. Most land surface models do not accurately represent peatland carbon emissions, partly because they do not represent the hydrologic cycle and/or microtopography adequately. Interactions between water table depth and microtopography in peatlands influence decomposition and modulate CO 2 and CH 4 fluxes. A modified version of the land surface component of the Energy Exascale Earth System Model, was recently created to represent the microtopography and hydrology of a raised dome bog in northern Minnesota, USA. In this study, three microtopographic parameters are analyzed in the modified version: hummock height, hummock‐hollow spacing, and percent hollow. Terrestrial laser scanning observations are used to set uncertainty bounds for these parameters. Our model experiment results suggest that carbon‐related quantities of interest (QOI) were typically the most sensitive to hummock height, and those QOI (especially net ecosystem exchange, NEE) were sensitive to interactions between parameters. Furthermore, NEE was most relatively influenced by microtopographic parameters in the model, varying by 35%. We found that increasing hummock height resulted in more C being stored in plant tissue and less in soil organic matter. This coincided with decreases in Sphagnum and increases in Picea and shrub net primary production. These results suggest that future studies may consider extending prognostic capabilities of carbon cycling by incorporating hummock hollow microtopography into earth system models.

58 GEOSCIENCES↗
NASA NTRS2009

Rotary Percussive Auto-Gopher for Deep Drilling and Sampling

The term "rotary percussive auto-gopher" denotes a proposed addition to a family of apparatuses, based on ultrasonic/ sonic drill corers (USDCs), that have been described in numerous previous NASA Tech Briefs articles. These apparatuses have been designed, variously, for boring into, and/or acquiring samples of, rock or other hard, brittle materials of geological interest. In the case of the rotary percussive autogopher, the emphasis would be on developing an apparatus capable of penetrating to, and acquiring samples at, depths that could otherwise be reached only by use of much longer, heavier, conventional drilling-and-sampling apparatuses. To recapitulate from the prior articles about USDCs: A USDC can be characterized as a lightweight, low-power jackhammer in which a piezoelectrically driven actuator generates ultrasonic vibrations and is coupled to a tool bit through a free mass. The bouncing of the free mass between the actuator horn and the drill bit converts the actuator ultrasonic vibrations into sonic hammering of the drill bit. The combination of ultrasonic and sonic vibrations gives rise to a hammering action (and a resulting chiseling action at the tip of the tool bit) that is more effective for drilling than is the microhammering action of ultrasonic vibrations alone. The hammering and chiseling actions are so effective that the size of the axial force needed to make the tool bit advance into soil, rock, or another material of interest is much smaller than in ordinary rotary drilling, ordinary hammering, or ordinary steady pushing. The predecessor of the rotary percussive auto-gopher is an apparatus, now denoted an ultrasonic/sonic gopher and previously denoted an ultrasonic gopher, described in "Ultrasonic/ Sonic Mechanism for Drilling and Coring" (NPO-30291), NASA Tech Briefs Vol. 27, No. 9 (September 2003), page 65. The ultrasonic/sonic gopher is intended for use mainly in acquiring cores. The name of the apparatus reflects the fact that, like a gopher, it periodically stops advancing at the end of the hole to bring excavated material (in this case, a core sample) to the surface, then re-enters the hole to resume the advance of the end of the hole. By use of a cable suspended from a reel on the surface, the gopher is lifted from the hole to remove a core sample, then lowered into the hole to resume the advance and acquire the next core sample.

Bar-Cohen, Yoseph↗