Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shape analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Particle Trajectory and Icing Analysis of the E(sup 3) Turbofan Engine Using LEWICE3D Version 3

Particle trajectory and ice shape calculations were made for the Energy Efficient Engine (E(sup 3)) using the LEWICE3D Version 3 software. The particle trajectory and icing computations were performed using the new "block-to-block" collection efficiency method which has been incorporated into the LEWICE3D Version 3 software. The E(sup 3) was developed by NASA and GE in the early 1980 s as a technology demonstrator and is representative of a modern high bypass turbofan engine. The E(sup 3) flow field was calculated using the NASA Glenn ADPAC turbomachinery flow solver. Computations were performed for the low pressure compressor of the E(sup 3) for a Mach 0.8 cruise condition at 11,887 m assuming a standard warm day for three drop sizes and two drop distributions typically used in aircraft design and certification. Particle trajectory computations were made for water drop sizes of 5, 20, and 100 microns. Particle trajectory and ice shape predictions were made for a 20 micron Langmuir-D distribution and for a 92 mm Super-cooled Large Droplet (SLD) distribution with and without splashing effects for a Liquid Water Content (LWC) of 0.3 g/cu m and an icing time of 30 min. The E3 fan and spinner combination proved to be an effective ice removal mechanism as they removed greater than 36 percent of the mass entering the inlet for the icing cases. The maximum free stream catch fraction for the fan and spinner combination was 0.60 while that on the elements downstream of the fan was 0.03. The non-splashing trajectory and collection efficiency results showed that as drop size increased impingement rates increased on the spinner and fan leaving less mass to impinge on downstream components. The SLD splashing case yielded more mass downstream of the fan than the SLD non-splashing case due to mass being splashed from the upstream inlet lip, spinner and fan components. The ice shapes generated downstream of the fan were either small or nonexistent due to the small available mass and evaporation except for the 92 m SLD splashing case. Relatively large ice shapes were predicted for internal guide vane #1 and rotor #1 for the 92 m SLD splashing case due to re-impingement of splashed mass.

Bidwell, Colin S.↗
NASA NTRS2021

What Makes Hybrid Concurrent Engineering Teams Work and Not Work: A Theoretical Analysis

Aerospace concurrent engineering teams (CETs) have been around since 1995 and have evolved into various shapes and forms. Historically, CETs have been designed to function with all team members physically collocated. In order to continue operating during the coronavirus pandemic, these teams have had to become fully distributed in 2020. Previously, distributed CETs were predicted to be considerably less efficient than traditional CETs. However, at JPL studies are being successfully run at peak rate in a distributed mode. As nominal working conditions resume after the pandemic, a major question is whether these teams must go back to being fully collocated or if they can become successful hybrid teams, with half or more of the engineers working remotely. In order to address this question, it is important to understand the key characteristics that make a CET more likely to be successful in a remote mode. This paper revisits a framework for characterizing concurrent engineering teams, providing a means to describe and compare the behavior of concurrent engineering teams in various settings [1], and uses the framework to make recommendations for future hybrid teams.

Chattopadhyay, Debarati↗
NASA NTRS1982

Direct system parameter identification of mechanical structures with application to modal analysis

In this paper a method is described to estimate mechanical structure characteristics in terms of mass, stiffness and damping matrices using measured force input and response data. The estimated matrices can be used to calculate a consistent set of damped natural frequencies and damping values, mode shapes and modal scale factors for the structure. The proposed technique is attractive as an experimental modal analysis method since the estimation of the matrices does not require previous estimation of frequency responses and since the method can be used, without any additional complications, for multiple force input structure testing.

Leuridan, J. M.↗
NASA NTRS2006

Non-Grey Radiation Modeling using Thermal Desktop/Sindaworks TFAWS06-1009

This paper provides an overview of the non-grey radiation modeling capabilities of Cullimore and Ring's Thermal Desktop(Registered TradeMark) Version 4.8 SindaWorks software. The non-grey radiation analysis theory implemented by Sindaworks and the methodology used by the software are outlined. Representative results from a parametric trade study of a radiation shield comprised of a series of v-grooved shaped deployable panels is used to illustrate the capabilities of the SindaWorks non-grey radiation thermal analysis software using emissivities with temperature and wavelength dependency modeled via a Hagen-Rubens relationship.

radiation modeling↗
NASA NTRS1984

Structural sensitivity analysis: Methods, applications and needs

Innovative techniques applicable to sensitivity analysis of discretized structural systems are reviewed. The techniques include a finite difference step size selection algorithm, a method for derivatives of iterative solutions, a Green's function technique for derivatives of transient response, simultaneous calculation of temperatures and their derivatives, derivatives with respect to shape, and derivatives of optimum designs with respect to problem parameters. Computerized implementations of sensitivity analysis and applications of sensitivity derivatives are also discussed. Some of the critical needs in the structural sensitivity area are indicated along with plans for dealing with some of those needs.

Adelman, H. M.↗
NASA NTRS1984

Adaptation of two-dimensional transonic analysis code, TSFOIL, for use in modeling adaptive wall test sections

The effects of the elastic deformation of the wind tunnel wall held to a streamline-like shape were simulated numerically. The wall itself is simulated by a finite element model and is allowed to deform under the pressure loading developing in the wind tunnel with an airfoil model present. A modified version of the transonic analysis program, TSFOIL, is then used to determine the resulting flow field with the effects of the deformed wall included, the shape of the wall and the flow field. Once a result from a particular operating condition was obtained, the pressure distribution on the airfoil in the wind tunnel model is compared with solutions generated by TSFOIL in the free air mode.

Webb, J.↗
NASA NTRS1997

An Experimental Investigation on the Static Equilibria and Dynamics of Liquid Bridges

A liquid bridge is a volume of liquid held between two or more solid supports. In the case of small disk supports with a sharp edge, the contact line between the bridge and the support disk will be anchored along the edge of the disk. For these cases the solid presents a geometrical singularity and the contact angle is indeterminate within a given range. This dissertation presents research conducted on liquid bridges with anchored contact lines. The three major topics covered are: determining the role of support geometry on static equilibria, liquid bridge dynamical behavior, and forces exerted by a liquid bridge on a support structure. The work was primarily experimental and conducted in a "Plateau tank" that allowed for the simulation of equivalent low-gravity conditions. The main thrust of the experimental work involved the use of a high resolution optical measurement system for imaging the dynamic zone shape, measurement of the static and dynamic contact angles and non-invasive analysis of excited surface modes. The liquid bridge was manipulated by computer controlled linear actuators which allowed precise control over the physical characteristics of the bridge. Experiments have been carried out to locate a bifurcation point along the maximum volume axisymmetric stability margin. Below the critical slenderness the bifurcation from an axisymmetric to a stable nonaxisymmetric configuration is supercritical. However, above this critical slenderness, the bifurcation is subcritical. A series of experiments analyzed the effect on axisymmetric bridge stability by using support disks of different radii, The shape behavior as transition points were approached, as well as the limiting case of a vanishing support radius was investigated. Experiments were performed to determine the resonant frequencies of axisymmetric bridges subject to lateral vibrations. Anomolous results led to a series of experiments to characterize nonlinearities present in the dynamic bridge shape. Finally, an attempt was made to experimentally measure the force exerted by the bridge on the lower support disk. This was done through use of a force balance apparatus. Particular attention was paid to the behavior of the bridge as the minimum volume stability limit was approached.

Resnick, Andrew Howard↗
NASA NTRS1992

Development of an analytical method to predict helicopter main rotor performance in icing conditions

Historically, certification of a helicopter for flight into known icing conditions was a problem. This is because of the current emphasis on flight testing for verification of system performance. Flight testing in icing conditions is difficult because, in addition to being dangerous and expensive, many times conditions which are sought after cannot be readily found in nature. The problem is compounded for helicopters because of their small range in comparison to many fixed wing aircraft. Thus, helicopters are forced to wait for conditions to occur in a certain region rather than seeking them out. These and other drawbacks to flight testing prompted extreme interest in developing validated alternatives to flight testing. One such alternative is theoretical prediction. It is desirable to have the ability to predict how a helicopter will perform when subjected to icing conditions. Herein, calculations are restricted to the main rotor, and are illustrated. The computational tool used to obtain performance is the lifting line analysis of B65. B65 incorporates experimental data into data banks in order to determine the section lift, drag, and moment characteristics of various airfoils at different Mach numbers and angles of attack. The local flow angle is calculated at user specified radial locations. This flow angle, along with the local Mach number is then cross referenced with the airfoil tables to obtain the local section characteristics. The local characteristics are then integrated together to obtain the entire rotor attributes. Once the clean performance is known, characterization of the type and shape of ice which accretes on the rotor blades is obtained using the analysis of LEWICE. The Interactive Boundary Layer (IBL) method then calculates the 2-D characteristics of the iced airfoil for input into the airfoil data bank of B65. Calculations are restricted to natural ice shedding and it is assumed that no de-icing takes place. Once the new lift, drag, and moment characteristics are known for the entire blade radius, this information is fed into B65, where the iced performance is then calculated.

Britton, Randall K.↗
NASA NTRS1986

Experimental study of effects of forebody geometry on high angle of attack static and dynamic stability

A series of low speed wind tunnel tests on a generic fighter model with a cylindrical fuselage were made to investigate the effects of forebody shape on static and dynamic lateral/directional stability. Five forebodies, including a chine nose of unconventional cross-sectional shape, were tested. Conventional force tests were conducted to determine static stability characteristics and single degree-of-freedom free-to-roll tests were used to study the wing rock susceptibility of the model with the various forebodies. Flow visualization data were obtained to aid in analysis of the complex flow phenomena involved. The results show that forebody cross-sectional shape can strongly effect both static and dynamic (roll) stability at high angles of attack. Large variations in stability were obtained for the various forebody geometries. These characteristics result from the impact of cross-sectional shape on forebody vortex development, the behavior of the vortices at sideslip conditions, and their interaction with the wing and empennage flow fields.

Brandon, J. M.↗
DOE OSTI2025

Deriving Stable Peak Models to Fit Complex XPS Data From Cu Contaminated Pt Electrocatalysts

X-ray Photoelectron Spectroscopy spectra peak models, designed to partition photoemission signals emanating from different elements or chemical states within an atom, are fitted to data limited to an energy interval over which inelastically scattered photoemission signal can be estimated. While the choice of background approximation and line shapes of components to the peak model requires careful consideration, the energy interval used to define the data to which the peak model is optimized has a significant impact on the final peak model. The relationship between the background intensity and data intensity at the start and end of the energy interval dictates the line shapes used in the peak model. In this work, we devise a method to peak fit a complex overlapping Cu 3p and Pt 4f XPS peak structure to perform the elemental quantification. We first use an Al 2s peak to illustrate how background curves approach data at the limits of the energy interval over which the background is defined, influencing the analysis of XPS spectra. Next, we demonstrate the nature of interactions between specific line shapes (Voigt and pseudo-Voigt profiles) suitable for photoemission peaks and a specific background curve (Shirley) and a peak model is presented that includes components to the peak model that accommodates background intensity during fitting of the peak model to data. The peak model allowed for quantification of the contributions of Pt 4f peaks emanating from the substrate that exhibits strong asymmetry in the presence of the inhomogeneously distributed Cu species, mostly of Lorentzian character.

XPS↗
NASA NTRS1980

Continuous coating of silicon-on-ceramic

Growth of sheet silicon on low-cost substrates has been demonstrated by the silicon coating with inverted meniscus (SCIM) technique. A mullite-based ceramic substrate is coated with carbon and then passed over a trough of molten silicon with a raised meniscus. Solidification occurs at the trailing edge of the downstream meniscus, producing a silicon-on-ceramic (SOC) layer. Meniscus shape and stability are controlled by varying the level of molten silicon in a reservoir connected to the trough. The thermal conditions for growth and the crystallographic texture of the SOC layers are similar to those produced by dip-coating, the original technique of meniscus-controlled growth. The thermal conditions for growth have been analyzed in some detail. The analysis correctly predicts the velocity-thickness relationship and the liquid-solid interface shape for dip-coating, and appears to be equally applicable to SCIM-coating. Solar cells made from dip-coated SOC material have demonstrated efficiencies of 10% on 4-sq cm cells and 9.9% on 10-sq cm cells.

Heaps, J. D.↗
NASA NTRS1990

Development of an integrated BEM approach for hot fluid structure interaction

A comprehensive boundary element method is presented for transient thermoelastic analysis of hot section Earth-to-Orbit engine components. This time-domain formulation requires discretization of only the surface of the component, and thus provides an attractive alternative to finite element analysis for this class of problems. In addition, steep thermal gradients, which often occur near the surface, can be captured more readily since with a boundary element approach there are no shape functions to constrain the solution in the direction normal to the surface. For example, the circular disc analysis indicates the high level of accuracy that can be obtained. In fact, on the basis of reduced modeling effort and improved accuracy, it appears that the present boundary element method should be the preferred approach for general problems of transient thermoelasticity.

Dargush, G. F.↗
DOE OSTI2020

Deposit geometry and oxygen concentration spatial variations due to composition change in printed functionally graded components

Functionally graded materials (FGMs) with site specific chemical composition are commonly manufactured by directed energy deposition (DED). Although previous work fabricated an FGM with a compositional variation between a ferritic and austenitic alloy, difficulties arose due to variations in deposit shape with composition change. This problem also occurs for FGMs in literature; however, unlike other cases, the thermophysical properties of these two alloys were similar throughout the build. Here, we investigate the role of chemical composition and surface-active elements on deposit geometry during the manufacture of FGMs by laser DED. Single-track experiments for the relevant FGM compositions are analyzed with results from a well-tested, three-dimensional, transient numerical heat transfer and fluid flow model and thermodynamic calculations. Experiments showed deposit shape varied as a function of composition for constant laser power and scan speed. Thermodynamic analysis indicated that the oxygen solubility in the fusion zone varied significantly for each composition used for the FGM. Numerical modeling revealed that the change in fluid flow caused by Marangoni convection due to dissolved oxygen in the fusion zone were mainly responsible for the changes in deposit shape observed in experiments. Finally, because oxygen can be introduced into the fusion zone through the feedstock as well as the surrounding atmosphere, these findings elucidate a previously unconsidered aspect of process control during DED fabrication of FGMs.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Structural sensitivity analysis: Methods, applications, and needs

Some innovative techniques applicable to sensitivity analysis of discretized structural systems are reviewed. These techniques include a finite-difference step-size selection algorithm, a method for derivatives of iterative solutions, a Green's function technique for derivatives of transient response, a simultaneous calculation of temperatures and their derivatives, derivatives with respect to shape, and derivatives of optimum designs with respect to problem parameters. Computerized implementations of sensitivity analysis and applications of sensitivity derivatives are also discussed. Finally, some of the critical needs in the structural sensitivity area are indicated along with Langley plans for dealing with some of these needs.

Adelman, H. M.↗
NASA NTRS2015

Design Concepts for Cooled Ceramic Composite Turbine Vane

The objective of this work was to develop design concepts for a cooled ceramic vane to be used in the first stage of the High Pressure Turbine(HPT). To insure that the design concepts were relevant to the gas turbine industry needs, Honeywell International Inc. was subcontracted to provide technical guidance for this work. The work performed under this contract can be divided into three broad categories. The first was an analysis of the cycle benefits arising from the higher temperature capability of Ceramic Matrix Composite(CMC) compared with conventional metallic vane materials. The second category was a series of structural analyses for variations in the internal configuration of first stage vane for the High Pressure Turbine(HPT) of a CF6 class commercial airline engine. The third category was analysis for a radial cooled turbine vanes for use in turboshaft engine applications. The size, shape and internal configuration of the turboshaft engine vanes were selected to investigate a cooling concept appropriate to small CMC vanes.

vanes↗
NASA NTRS1972

Twenty-seven-day recurrences in the solar-wind speed - Mariner 2.

Results of an autocorrelation analysis of the Mariner 2 data concerning solar-wind speed obtained in late 1962. A statistically significant correlation associated with the solar rotation has been found near a lag of 27 days; however, the amplitude of the correlation is only about 0.4, in essential agreement with measurements of Vela 2 and 3 during the period from July 1964 to July 1967. The relatively modest correlation is interpreted to mean that a number of speed structures observed by Mariner 2 did not endure for more than one solar rotation; those structures that did endure evolved significantly in shape, amplitude, and solar longitude from one solar rotation to the next. The analysis also shows that typical solar-wind structures occupied about 30 to 45 deg in solar longitude near 1 AU.

Gosling, J. T.↗
NASA NTRS1989

Calculation of Weibull strength parameters and Batdorf flow-density constants for volume- and surface-flaw-induced fracture in ceramics

The calculation of shape and scale parametes of the two-parameter Weibull distribution is described using the least-squares analysis and maximum likelihood methods for volume- and surface-flaw-induced fracture in ceramics with complete and censored samples. Detailed procedures are given for evaluating 90 percent confidence intervals for maximum likelihood estimates of shape and scale parameters, the unbiased estimates of the shape parameters, and the Weibull mean values and corresponding standard deviations. Furthermore, the necessary steps are described for detecting outliers and for calculating the Kolmogorov-Smirnov and the Anderson-Darling goodness-of-fit statistics and 90 percent confidence bands about the Weibull distribution. It also shows how to calculate the Batdorf flaw-density constants by using the Weibull distribution statistical parameters. The techniques described were verified with several example problems, from the open literature, and were coded in the Structural Ceramics Analysis and Reliability Evaluation (SCARE) design program.

Shantaram, S. Pai↗
NASA NTRS1991

Equilibria, stability and bifurcations of rotating columns of fluid subjected to planar disturbances

Long gyrostatically rotating drops bonded by surface tension are amenable to conventional bifurcation analysis and newer, computer-aided analytical methods, and therefore are useful prototypes of three-dimensional drops. A study is conducted by setting aside instability to Rayleigh's axisymmetric mode and investigating the effects of translationally symmetric (planar) disturbances. The disadvantage of employing single-coordinate representation of drop shapes close to break-up is brought out. It is shown that a family of symmetric two-lobed shapes bifurcates from the main family of perfectly cylindrical shapes when the rotation rate reaches a critical value, in accord with the linearized hydrodynamic analysis of Hocking.

Benner, R. E., Jr.↗