Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rig”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Limit pressure of a circumferentially reinforced SiC/Ti ring

Limit loads under plane stress and plane strain are found for a circumferentially reinforced elastoplastic ring subjected to interior pressure. These are used as bounds on an estimate of the failure pressure of a SiC/Ti test rig that is being fabricated and tested. The ring is to serve as a benchmark against which deformation and failure analysis methods can be assessed. An anisotropic perfect plasticity idealization of the SiC/Ti ring material is made and used in the limit load calculations. An estimate of the failure pressure of the NASA/PW benchmark test ring is given.

Robinson, D. N.↗
NASA NTRS1992

On the coupling between a supersonic boundary layer and a flexible surface

The coupling between a two-dimensional, supersonic, laminar boundary layer and a flexible surface is studied using direct numerical computations of the Navier-Stokes equations coupled with the plate equation. The flexible surface is forced to vibrate by plane acoustic waves at normal incidence emanated by a sound source located on the side of the flexible surface opposite to the boundary layer. The effect of the source excitation frequency on the surface vibration and boundary layer stability is analyzed. We find that, for frequencies near the fifth natural frequency of the surface or lower, large disturbances are introduced in the boundary layer which may alter its stability characteristics. The interaction between a stable two-dimensional disturbance of Tollmien-Schlichting (TS) type with the vibrating surface is also studied. We find that the disturbance level is higher over the vrating flexible surface than that obtained when the surface is rig id, which indicates a strong coupling between flow and structure. However, in the absence of the sound source the disturbance level over the rigid and flexible surfaces are identical. This result is due to the high frequency of the TS disturbance which does not couple with the flexible surface.

Frendi, Abdelkader↗
NASA NTRS1992

Ceramic matrix composites for rocket engine turbine applications

A program to establish the potential for introducing fiber reinforced ceramic matrix composites (FRCMC) in future rocket engine turbopumps was instituted in 1987. A brief summary of the overall program (both contract and in-house research) is presented. Tests at NASA Lewis include thermal upshocks in a hydrogen/oxygen test rig capable of generating heating rates up to 2500 C/sec. Post thermal upshock exposure evaluation includes the measurement of residual strength and failure analysis. Test results for monolithic ceramics and several FRCMC are presented. Hydrogen compatibility was assessed by isothermal exposure of monolithic ceramics in high temperature gaseous hydrogen plus water vapor.

Herbell, Thomas P.↗
NASA NTRS1992

NASP - Focus on technology

The major changes in the NASP program caused mostly by budget pressures are described and current technology developments are highlighted. Particular attention is given to the program funding, vehicle and engine design, and the technology program. It is concluded that the success of the X-30 vehicle design depends on the success of the technology development effort. The major accomplishments of the NASP technology program include the T-5 Shock Tunnel at California Institute of Technology and Mach 16 injection and mixing experiments conducted in this facility; the low speed component integration rig which provide data on engine operation from static conditions to Mach 3.5; the module to module interaction test which provided data on the effects of inlet unstart in one engine module on an adjacent module at Mach 4.3; and the direct-connect module used for fuel injection and mixing studies at Mach 6-8.

Waldman, Barry J.↗
NASA NTRS1992

Laser absorption flow diagnostics for use in hypersonic ground-based and flight experiments

Consideration is given to laboratory ground-based scale systems for measuring OH and NO and diode laser systems for measuring O2 and H2O. Several diagnostic instruments which are currently being used in a scramjet combustor test rig of the Ames 16-inch shock tunnel are described. Data on mole fraction, temperature, density, pressure, and velocity is obtained using specific data reduction techniques. These measurements provide critical data for evaluation of the propulsion system performance which include mass capture for quantification of fuel equivalence ratio (O2), flow contamination and emission levels (NO), combustion progress (OH), and injector mixing and combustion efficiency (H2O).

Cavolowsky, John A.↗
NASA NTRS1993

An overview of shed ice impact studies in the NASA Lewis Icing Research Tunnel

One of the areas of active research in commercial and military rotorcraft is directed toward developing the capability of sustained flight in icing conditions. The emphasis to date has been on the accretion and subsequent shedding of ice in an icing environment, where the shedding may be natural or induced. Historically, shed-ice particles have been a problem for aircraft, particularly rotorcraft. Because of the high particle velocities involved, damage to a fuselage or other airframe component from a shed-ice impact can be significant. Design rules for damage tolerance from shed-ice impact are not well developed because of a lack of experimental data. Thus, NASA Lewis (LeRC) has begun an effort to develop a database of impact force and energy resulting from shed ice. This effort consisted of a test of NASA LeRC's Model Rotor Test Rig (MRTR) in the Icing Research Tunnel (IRT). Both natural shedding and forced shedding were investigated. Forced shedding was achieved by fitting the rotor blades with Small Tube Pneumatic (STP) deicer boots manufactured by BF Goodrich. A detailed description of the test is given as well as the design of a new impact sensor which measures the force-time history of an impacting ice fragment. A brief discussion of the procedure to infer impact energy from a force-time trace are required for the impact-energy calculations. Recommendations and future plans for this research area are also provided.

Britton, Randall K.↗
NASA NTRS1993

Navier-Stokes computations and experimental comparisons for multielement airfoil configurations

A two-dimensional unstructured Navier-Stokes code is utilized for computing the flow around multielement configurations. Comparisons are shown for a landing configuration with an advanced-technology flap as well as for a takeoff configuration. For each, a grid convergence study is conducted to assess inaccuracies caused by inadequate grid resolution. Although adequate resolution is obtained for determining the pressure distributions, further refinement is needed to sufficiently resolve the velocity profiles at high angles of attack. For the advanced flap configuration, comparisons of pressure distributions and lift are made with experimental data. Here, two flap riggings and two Reynolds numbers are considered. In general, the trends caused by variations in these quantities are well predicted by the computations, although the angle of attack for maximum lift is overpredicted. For the takeoff configuration, comparisons between pressures, velocity profiles, and Reynolds stresses are made at a single angle of attack with generally good agreement.

Anderson, W. K.↗
NASA NTRS1993

Progress in high-lift aerodynamic calculations

The current work presents progress in the effort to numerically simulate the flow over high-lift aerodynamic components, namely, multi-element airfoils and wings in either a take-off or a landing configuration. The computational approach utilizes an incompressible flow solver and an overlaid chimera grid approach. A detailed grid resolution study is presented for flow over a three-element airfoil. Two turbulence models, a one-equation Baldwin-Barth model and a two equation k-omega model are compared. Excellent agreement with experiment is obtained for the lift coefficient at all angles of attack, including the prediction of maximum lift when using the two-equation model. Results for two other flap riggings are shown. Three-dimensional results are presented for a wing with a square wing-tip as a validation case. Grid generation and topology is discussed for computing the flow over a T-39 Sabreliner wing with flap deployed and the initial calculations for this geometry are presented.

Rogers, Stuart E.↗
NASA NTRS1991

Acoustical analysis of gear housing vibration

The modal and acoustical analysis of the NASA gear-noise rig is described. Experimental modal analysis techniques were used to determine the modes of vibration of the transmission housing. The resulting modal data were then used in a boundary element method (BEM) analysis to calculate the sound pressure and sound intensity on the surface of the housing as well as the radiation efficiency of each mode. The radiation efficiencies of the transmission housing modes are compared with theoretical results for finite, baffled plates. A method that uses the measured mode shapes and the BEM to predict the effect of simple structural changes on the sound radiation efficiency of the modes of vibration is also described.

Seybert, A. F.↗
NASA NTRS1993

An efficient liner cooling scheme for advanced small gas turbine combustors

A joint Army/NASA program was conducted to design, fabricate, and test an advanced, small gas turbine, reverse-flow combustor utilizing a compliant metal/ceramic (CMC) wall cooling concept. The objectives of this effort were to develop a design method (basic design data base and analysis) for the CMC cooling technique and then demonstrate its application to an advanced cycle, small, reverse-flow combustor with 3000 F burner outlet temperature. The CMC concept offers significant improvements in wall cooling effectiveness resulting in a large reduction in cooling air requirements. Therefore, more air is available for control of burner outlet temperature pattern in addition to the benefits of improved efficiency, reduced emissions, and lower smoke levels. The program was divided into four tasks. Task 1 defined component materials and localized design of the composite wall structure in conjunction with development of basic design models for the analysis of flow and heat transfer through the wall. Task 2 included implementation of the selected materials and validated design models during combustor preliminary design. Detail design of the selected combustor concept and its refinement with 3D aerothermal analysis were completed in Task 3. Task 4 covered detail drawings, process development and fabrication, and a series of burner rig tests. The purpose of this paper is to provide details of the investigation into the fundamental flow and heat transfer characteristics of the CMC wall structure as well as implementation of the fundamental analysis method for full-scale combustor design.

Paskin, Marc D.↗
NASA NTRS1993

Design and test of a small two stage counter-rotating turbine for rocket engine application

The aerodynamic design and rig test evaluation of a small counter-rotating turbine system is described. The technology represented by this turbine is being developed for application in an advanced upper stage rocket engine turbopump. This engine will employ an oxygen/hydrogen expander cycle and achieve high performance through efficient combustion, high combustion pressure, and high area ratio exhaust nozzle expansion. Engine performance goals require that the turbopump drive turbines achieve high efficiency at low gas flow rates. The low flow rates result in very small airfoil diameter, height and chord. The high efficiency and small size requirements present a challenging turbine design problem. The unconventional approach employed to meet this challenge is described, along with the detailed design process and resulting airfoil configurations. The method and results of full scale aerodynamic performance evaluation testing of both one and two stage configurations, as well as operation without the secondary stage stator are presented. The overall results of this effort illustrate that advanced aerodynamic design tools and hardware fabrication techniques have provided improved capability to produce small high performance turbines for advanced rocket engines.

Huber, F. W.↗
NASA NTRS1993

Evaluation of a vibration diagnostic system for the detection of spur gear pitting failures

A vibration diagnostic system was used to detect spur gear surface pitting fatigue in a closed-loop spur gear fatigue test rig. The diagnostic system, comprising a personal computer with an analog-to-digital conversion board, a diagnostic system unit, and software, uses time-synchronous averaging of the vibration signal to produce a vibration image of each tooth on any gear in a transmission. Several parameters were analyzed including gear pair stress wave and raw baseband vibration, kurtosis, peak ratios, and others. The system provides limits for the various parameters and gives a warning when the limits are exceeded. Several spur gear tests were conducted with this system and vibration data analyzed at 5-min. intervals. The results presented herein show that the system is fairly effective at detecting spur gear tooth surface fatigue pitting failures.

Townsend, Dennis P.↗
NASA NTRS1938

The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J

The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.

House, R O↗
NASA NTRS1957

Preliminary metallographic studies of ball fatigue under rolling-contact conditions

The metallurgical results produced on balls tested in the rolling-contact fatigue spin rig were studied by metallographic examination. Origin and progression of fatigue failures were observed. These evaluations were made on SAE 52100 and AISI M-1 balls fatigue tested at room temperature (80 F) and 200 to 250 F. Most failures originated subsurface in shear; inclusions, structure changes, and directionalism adversely affected ball fatigue life. Structures in the maximum-shear-stress region of the balls of both materials were stable at room temperature and unstable at 200 to 250 F. Failures were of the same type as those found in full-scale bearings.

SURFACES, CONTACT - ROLLING↗
NASA NTRS1957

Effect of Fiber Orientation on Ball Failures Under Rolling-contact Conditions

The rolling-contact fatigue spin rig was used to test bails of a bearing steel at maximum Hertz stresses of 600,000 to 750,000 psi. The effect of fiber orientation was observed with the ball track restricted to passing directly over the poles, coincident with the equator, or randomly around the ball. The polar areas were found to be weaker in fatigue than the nonpolar areas. This resulted in a much greater portion of the failures occurring in the polar areas than would be expected from a homogeneous material. The early failures are discussed.

MATERIALS, PROPERTIES - FATIGUE↗
NASA NTRS1955

Effect of Dissolved Oxygen on the Filterability of Jet Fuels for Temperatures Between 300 Degrees and 400 Degrees F

The effect of dissolved oxygen in the filter-clogging characteristics of three JP-4 and two JP-5 fuels was studied at 300 degrees to 400 degrees F in a bench- scale rig, employing filter paper as the filter medium. The residence time of the fuel at the high temperature was approximately 6 seconds. For these conditions, the clogging characteristics of the fuels increased with both increasing temperature and increasing concentration of dissolved oxygen. The amount of insoluble material formed at high temperatures necessary to produce clogging of filters was very small, of the order of 1 milligram per gallon of fuel.

Mckeown, Anderson B↗
NASA NTRS1923

Control in Circling Flight

This investigation was undertaken for the purpose of developing instruments that would record the forces and positions of all three controls, and to obtain data on the behavior of an airplane in turns. All the work was done on a standard rigged JN4H (airplane no. 2 of National Advisory Committee for Aeronautics, report no. 70). It was found that the airplane was longitudinally unstable and nose heavy; that it was laterally unstable, probably due to too little dihedral; and that it was directionally unstable, due to insufficient fin area, this last being very serious, for in case of a loss of rudder control the airplane immediately whips into a spin from which there is no way of getting it out. On the other hand, it was found possible to fly quite satisfactorily with the rudder locked, and safely, though not so well, with the ailerons locked.

Norton, F H↗
NASA NTRS1923

Damping coefficients due to tail surfaces in aircraft

The object of the investigation described in this report was to compare the damping coefficients of an airfoil as calculated from a knowledge of the static characteristics of the section with those obtained experimentally with an oscillation. The damping coefficients as obtained, according to the conventional notation, can be considered either as due to pitching or as due to yawing, the oscillation in these experiments being so arranged that the surfaces oscillate about a vertical axis. This is in reality the case when the influence is yawing about the standard Z-axis, but it can also be considered as a pitching motion when the model is so rigged that its standard Y-axis becomes vertical. The horizontal oscillation has the advantage of eliminating the gravity action and avoiding the use of counterweights, whose presence in the wind tunnel is undesirable because of their interference with the air flow. The real point of the investigation was to separate the damping due to rotation from that due to translation. By varying the distance between the center of pressure and the center of rotation on the oscillator, the variation of damping moment can be observed and the rotational and translational effects can be separated.

Chu, Lynn↗