Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “numerical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Numerical study on pressure wave propagation in a mercury loop

On-beam tests were carried out at the Los Alamos Neutron Science Center Weapons Neutron Research (LANSCE WNR) facility in June 2005 to investigate pressure wave mitigation in mercury targets for the MW-class spallation neutron sources under international collaboration between US Spallation Neutron Source (SNS) and Japanese Spallation Neutron Source (JSNS). A mercury loop was used for the target, a so-called In-Beam Bubbling Test Loop (IBBTL). The loop consists of the rectangular pipe of 25 mm x 50 mm^2 in cross section, 1.5 mm in wall thickness and 2 m in total length approximately. The SNS team set 8 strain sensors on the pipe wall to measure the strain propagation caused by the pressure wave. The maximum strain appeared at 350 mm apart from the proton-bombarded point at 5.5 ms after the proton bombardment. It is known that the propagation velocity of the pressure wave in mercury is ca. 1500 m/s and that of the stress wave in stainless steel is ca. 5000 m/s. However, the apparent wave propagation velocity in the IBBTL was lower than those velocities and was observed to be 65 m/s. Numerical analysis was carried out to understand the strain propagation in the pipe wall of the IBBTL. Numerical results showed that the maximum strain at 350 mm apart from the beam spot appeared at 5.5 ms after proton bombardment in good agreement with experimental results.

mercury↗

Numerical Verification of Equilibrium Thermodynamic Computations in Nuclear Fuel Performance Codes

There is an increasing desire to integrate thermodynamic computations directly into multi-physics nuclear fuel performance and safety codes. These computations provide, among other matters, boundary conditions in heat and mass transport modules in predicting fuel behaviour. Precision must be maintained in computations involving fission and activation products with very low concentrations which may nonetheless have significant radiological consequences. Also, there is the concern about the propagation of numerical errors in multi-physics codes. A method to numerically verify equilibrium thermodynamic computations is therefore necessary to satisfy rigorous quality assurance standards of the nuclear industry without significantly impeding computational performance. A technique is presented that can be applied to systems of any number of phases and system components. The technique is reliable and comprehensive in ensuring that all conceivable equilibrium constants have been satisfied without having to formulate each one of a potentially very large number.

Piro, Markus↗

An effective numerical algorithm for intra-granular fission gas release during non-equilibrium trapping and resolution

Both fission gas release and gaseous swelling in nuclear fuel are driven by the transport of fission gas from within the fuel grains to grain boundaries (intra-granular fission gas release). The process involves gas atom diffusion in conjunction with trapping in and resolution from intra-granular bubbles, and is described mathematically by a system of two partial differential equations (PDE). Following Speight, under the assumption of equilibrium between trapping and resolution (quasi-stationary approximation) the system can be reduced to a single diffusion equation with an effective diffusion coefficient. Numerical solutions used in engineering fuel performance calculations invariably rely on this simplification. First, we investigate the validity of the quasi-stationary approximation compared to the solution of the general system of PDEs. Results demonstrate that the approximation is valid under most conditions of practical interest, but is inadequate to model intra-granular fission gas release during rapid transients to relatively high temperatures such as postulated reactivity initiated accidents (RIA). Then, we develop a novel numerical algorithm for the solution of the general problem in time-varying conditions. We verify the PolyPole-2 algorithm against a reference finite difference solution for a large number of randomly generated operation histories including prototypical RIA transients. Results demonstrate that PolyPole-2 captures the solution of the general PDE system with a high accuracy and a low computational cost. As a result, the PolyPole-2 algorithm overcomes the quasi-stationary approximation and the concept of an effective diffusion coefficient for the solution of the intra-granular fission gas release problem in nuclear fuel analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experimental and numerical study of the shielding effect of two tandem rough cylinders in flow-induce oscillation

The shielding effect of the downstream cylinder in flow induced oscillation (FIO) of two cylinders arranged in tandem is studied experimentally and numerically at Reynolds number 30,000 to 120,000. Both cylinders are in one degree-of-freedom, transverse-oscillations, and have turbulence stimulation in the form of selective surface roughness to expand FIO beyond vortex-induced vibration (VIV) into galloping. Shielding of the downstream cylinder has a negative effect on harnessing hydrokinetic energy. Further, to study its effect and mechanics, selective cases are studied both numerically and experimentally and discussed to demonstrate the shielding effect on the downstream cylinder and understand its cause. The main conclusions are: (1) The shielding effect for the downstream cylinder shows a strong relation to the damping ratio. As the damping ratio increases, the shielding effect is mitigated. Additionally, the oscillation of the rear cylinder becomes stable and shows stable frequency. (2) In the VIV region, as the stiffness and natural frequency increase, the shielding effect decreases substantially. (3) In the VIV region, the vorticity of the vortices shedding from both the upper and the lower sides of the downstream cylinder does not accumulate enough due to the attraction by the vortices shed from the upstream cylinder, thus resulting in partial suppression of the oscillation on the downstream cylinder. (4) In the galloping region, the shielding effect for the downstream cylinder depends on whether the vorticity near the downstream cylinder is strengthened by the vortices generated by the shear layers of the upstream cylinder or weakened.

42 ENGINEERING↗

Neutron residual stress measurement and numerical modeling in a curved thin-walled structure by laser powder bed fusion additive manufacturing

Severe residual stresses in metal parts made by laser powder bed fusion additive manufacturing processes (LPBFAM) can cause both distortion and cracking during the fabrication processes. Limited data is currently available for both iterating through process conditions and design, and in particular, for validating numerical models to accelerate process certification. In this work, residual stresses of a curved thin-walled structure, made of Ni-based superalloy Inconel 625™ and fabricated by LPBFAM, were resolved by neutron diffraction without measuring the stress-free lattices along both the build and the transverse directions. The stresses of the entire part during fabrication and after cooling down were predicted by a simplified layer-by-layer finite element based numerical model. The simulated and measured stresses were found in good quantitative agreement. The validated simplified simulation methodology will allow to assess residual stresses in more complex structures and to significantly reduce manufacturing cycle time.

36 MATERIALS SCIENCE↗

Recent numerical and algorithmic advances within the volume tracking framework for modeling interfacial flows

A review of recent advances made in numerical methods and algorithms within the volume tracking framework is presented. The volume tracking method, also known as the volume-of-fluid method has become an established numerical approach to model and simulate interfacial flows. Its advantage is its strict mass conservation. However, because the interface is not explicitly tracked but captured via the material volume fraction on a fixed mesh, accurate estimation of the interface position, its geometric properties and modeling of interfacial physics in the volume tracking framework remain difficult. Several improvements have been made over the last decade to address these challenges. In this study, the multimaterial interface reconstruction method via power diagram, curvature estimation via heights and mean values and the balanced-force algorithm for surface tension are highlighted.

97 MATHEMATICS AND COMPUTING↗

Numerical study of the ignition behavior of a post-discharge kernel in a turbulent stratified crossflow

Ensuring robust ignition is critical for the operability of aeronautical gas-turbine combustors. For ignition to be successful, an important aspect is the ability of the hot gas generated by the spark discharge to initiate combustion reactions, leading to the formation of a self-sustained ignition kernel. This study focuses on this phenomena by performing simulations of kernel ignition in a crossflow configuration that was characterized experimentally. First, inert simulations are performed to identify numerical parameters correctly reproducing the kernel ejection from the ignition cavity, which is here modeled as a pulsed jet. In particular, the kernel diameter and the transit time of the kernel to the reacting mixture are matched with measurements. Considering stochastic perturbations of the ejection velocity of the ignition kernel, the variability of the kernel transit time is also reproduced by the simulations. Subsequently, simulations of a series of ignition sequences are performed with varying equivalence ratio of the fuel-air mixture in the crossflow. The numerical results are shown to reproduce the ignition failure that occurs for the leanest equivalence ratio ($φ = 0.6$). For higher equivalence ratios, the simulations are shown to capture the sensitivity of the ignition to the equivalence ratio, and the kernel successfully transitions into a propagating flame. Significant stochastic dispersion of the ignition strength is observed, which relates to the variability of the transit time of the kernel to the re- active mixture. An analysis of the structure of the ignition kernel also highlights the transition towards a self-propagating flame for successful ignition conditions.

42 ENGINEERING↗

High frequency content in nonlinear soil response: A numerical artifact or a reality?

This article probes the reasons for the presence of high frequency components, which are not a part of the input, in the output of nonlinear site response analysis. The nonlinear site response analysis of a single soil element, under a single frequency sinusoidal displacement, is conducted to demonstrate the presence of frequencies higher than the input frequency in the soil element's shear stress and the free surface acceleration. The parameters of this one element problem are chosen carefully to minimize numerical errors. The shape of the stress-strain hysteresis loop is found to be the main cause for the presence of these higher frequencies. A quasi-static problem similar to the direct shear test is then considered to analyze the effect of different hysteresis shapes. Through this analysis, it is numerically and analytically shown that any deviation of the stress-strain hysteresis shape from a perfect ellipse results in output frequencies higher than the input frequency and the number of higher frequencies produced depends on whether the hysteresis shape is smooth or pointed.

42 ENGINEERING↗

Systematic parameter study of a nonlinear electromagnetic energy harvester with matched magnetic orientation: Numerical simulation and experimental investigation

Here, this paper reports the systematic parameter study of a tristable nonlinear electromagnetic energy harvester for ambient low-frequency vibration. Numerical simulations and experimental investigations are performed on the harvester which consists of a cantilever beam, a tip coil, two tip magnets and two external side magnets. The external side magnets are deployed symmetrically along a concave surface parallel to the trajectory of the cantilever tip with a controllable distance so that the magnetic orientation of the tip magnets are matched with that of the side magnets. Therefore, instead of the ternary position parameters (d, h, α), a binary parameters pair (d 0 , d) is used to characterize the position of the side magnets and the performance of the energy harvester. The magnetic force and magnetic field on the cantilever tip therefore depend on the relative distance in the tip displacement direction between the tip magnets and side magnets, but is independent of the position of the side magnets on the concave surface. The magnetic force (field)-distance relationship is measured experimentally and curve fitted to obtain explicit expressions, in order to characterize the magnetic force (field) when the side magnets are placed at varied positions along the concave surface. Numerical simulation is, then, performed to predict the electromagnetic voltage output and the bandwidth of the energy harvester. The simulation results coincided with the measured data. Significant broadband response is obtained experimentally and the maximum RMS power output is 40.2 mW at 0.45 g of excitation. Furthermore, the proposed structure showcasing the matched magnetic orientation is characterized by the binary parameters pair (d 0 , d) and the systematic parametric approach could contribute to the design and study of nonlinear broadband energy harvesters.

30 DIRECT ENERGY CONVERSION↗

A transfer learning approach for acoustic emission zonal localization on steel plate-like structure using numerical simulation and unsupervised domain adaptation

The detection and localization of damage in metallic structures using acoustic emission (AE) monitoring and artificial intelligence technology such as deep learning has been widely studied. However, a current challenge of this approach is the difficulty of obtaining sufficient labeled historical AE signals for the training process of deep learning models. This problem can be approached through the implementation of transfer learning. The innovation of this paper lies in the development of a transfer learning approach for AE source localization on a stainless-steel structure when no historical labeled AE signals are available for training. A finite element model is developed to generate numerical AE signals for the training. Unsupervised domain adaptation (UDA) technology is utilized to reduce the distribution difference between the numerical and the realistic AE signals and to derive the localization results of the unlabeled realistic AE signals. Finally, the results suggest that the proposed approach is capable of localizing AE signals with high accuracy in the absence of labeled training data.

42 ENGINEERING↗

Vorticity moments in four numerical simulations of the 3D Navier–Stokes equations

Abstract The issue of intermittency in numerical solutions of the 3D Navier–Stokes equations on a periodic box ${[0, L] }^{3} $ is addressed through four sets of numerical simulations that calculate a new set of variables defined by ${D}_{m} (t)= {({ \varpi }_{0}^{- 1} {\Omega }_{m} )}^{{\alpha }_{m} } $ for $1\leq m\leq \infty $ where ${\alpha }_{m} = 2m/ (4m- 3)$ and ${[{\Omega }_{m} (t)] }^{2m} = {L}^{- 3} \int \nolimits _{\mathscr{V}} {\vert \boldsymbol{\omega} \vert }^{2m} \hspace{0.167em} \mathrm{d} V$ with ${\varpi }_{0} = \nu {L}^{- 2} $ . All four simulations unexpectedly show that the ${D}_{m} $ are ordered for $m= 1, \ldots , 9$ such that ${D}_{m+ 1} \lt {D}_{m} $ . Moreover, the ${D}_{m} $ squeeze together such that ${D}_{m+ 1} / {D}_{m} \nearrow 1$ as $m$ increases. The values of ${D}_{1} $ lie far above the values of the rest of the ${D}_{m} $ , giving rise to a suggestion that a depletion of nonlinearity is occurring which could be the cause of Navier–Stokes regularity. The first simulation is of very anisotropic decaying turbulence; the second and third are of decaying isotropic turbulence from random initial conditions and forced isotropic turbulence at fixed Grashof number respectively; the fourth is of very-high-Reynolds-number forced, stationary, isotropic turbulence at up to resolutions of $409{6}^{3} $ .

Mechanics↗

Onset of instabilities in rotating flows by direct numerical simulation

A rotating disk is the canonical experiment for measuring surface reaction rates in geochemical and electrochemical systems. Using the similarity solution for laminar flow around an infinite disk, the mass transfer coefficient can be simply related to the intrinsic reaction rate at the surface. However, measurements of mass transfer rates use a finite-size disk within a larger container of solution; here the flow is no longer strictly laminar, but there must always be some recirculation. Our interest was initially in the assumption of a uniform radial concentration field, how this breaks down near the perimeter of the disk, and what effect that might have on the measured mass transfer rates. However, our numerical simulations suggest that the flow around a finite-size disk becomes time dependent at Reynolds number ($\textit{Re}$) below 1000, which is much smaller than the typical values in mass-transfer measurements ($\textit{Re}$~10 4 ). In this work, we observe the formation of coherent structures in the flow, which suggest a non-uniform mass transfer at the disk surface. The rotating-disk flow follows a similar sequence of instabilities to the Taylor–Couette flow: a centrifugal instability leading an axisymmetric, time-invariant flow, followed by a Hopf bifurcation to a time-periodic flow. To minimise the possibility that our results are a numerical artefact, we have also simulated the instability in the stationary boundary layer of a rotor–stator flow, comparing with self-similar solutions at low $\textit{Re}$ and with spectral methods near the critical Reynolds number.

42 ENGINEERING↗

Modeling pure methane hydrate dissociation using a numerical simulator from a novel combination of X-ray computed tomography and macroscopic data

The numerical simulator TOUGH+HYDRATE (T+H) was used to predict the transient pure methane hydrate (no sediment) dissociation data. X-ray computed tomography (CT) was used to visualize the methane hydrate formation and dissociation processes. A methane hydrate sample was formed from granular ice in a cylindrical vessel, and slow depressurization combined with thermal stimulation was applied to dissociate the hydrate sample. CT images showed that the water produced from the hydrate dissociation accumulated at the bottom of the vessel and increased the hydrate dissociation rate there. CT images were obtained during hydrate dissociation to confirm the radial dissociation of the hydrate sample. This radial dissociation process has implications for dissociation of hydrates in pipelines, suggesting lower dissociation times than for longitudinal dissociation. These observations were also confirmed by the numerical simulator predictions, which were in good agreement with the measured thermal data during hydrate dissociation. System pressure and sample temperature measured at the sample center followed the CH{sub 4} hydrate L{sub w}+H+V equilibrium line during hydrate dissociation. The predicted cumulative methane gas production was within 5% of the measured data. Thus, this study validated our simulation approach and assumptions, which include stationary pure methane hydrate-skeleton, equilibrium hydrate-dissociation and heat- and mass-transfer in predicting hydrate dissociation in the absence of sediments. It should be noted that the application of T+H for the pure methane hydrate system (no sediment) is outside the general applicability limits of T+H.

54 ENVIRONMENTAL SCIENCES↗

Numerical simulation of multiphase flow and collision humidification in the multifluid alkaline spray generator for a novel semidry flue gas desulfurization system

A hybrid Eulerian-Lagrangian model was developed to simulate gas-droplet-particle multiphase flow and the collision humidification between sorbent particles and spray droplets in the confined multifluid alkaline spray generator for a novel semidry flue gas desulfurization system. In this model, the motions of discrete phases were tracked simultaneously by using a stochastic trajectory approach, and a probability model of droplets catching particles was presented to judge whether sorbent particles were caught with direct simulation Monte Carlo method. Numerical humidification efficiency of sorbent particles is validated by the experimental one deduced from the measured desulfurization efficiency. The effects of flue gas flow rate, spray droplet diameter, sorbent particle diameter, and particle injection location on the humidification efficiency were optimized. Numerical results show that the collision humidification efficiency of sorbent particles increases significantly at the axial distance of 1.67 times the generator diameter from the nozzle tip and reaches 78.5% without recirculation flow in the alkaline spray generator when the ratio of flue gas mass flow rate to spray water mass flow rate is 6.7. Moreover, there is an optimal droplet diameter ranging from 125 to 150 {mu} m and an optimal particle injection location corresponding to the maximum humidification efficiency in this paper.

01 COAL, LIGNITE, AND PEAT↗

Numerically Relevant Timescales in the MG2 Microphysics Model

Climate models rely on parameterizations of a variety of processes in the atmospheric physics, but a common concern is that the temporal resolution is too coarse to consistently resolve the behavior that individual parameterizations are designed to capture. This study examines timescales numerically derived from the Morrison-Gettelman (MG2) microphysics as implemented within the Energy Exascale Earth System Model, version 1 (E3SMv1). Numerically relevant timescales in MG2 are derived by computing the eigenspectrum of its Jacobian. These timescales are found to often be smaller than the default 5 min time step used for MG2. The fast timescales are then heuristically connected to individual microphysics processes. By substepping a few particular rain processes within MG2, the time discretization error for those processes was considerably reduced with minimal additional expense to the overall microphysics. While this improvement has a substantial effect on the target processes and on the vertical distribution of stratiform-derived rain within E3SMv1, the overall model climate is found to not be sensitive to MG2 time step. Here, we hypothesize that this is because the surface climate does not depend strongly on certain process rates, especially MG2's rain evaporation rate.

58 GEOSCIENCES↗

Analytical and numerical modeling of optical second harmonic generation in anisotropic crystals using #SHAARP package

Electric-dipole optical second harmonic generation (SHG) is a second-order nonlinear process that is widely used as a sensitive probe to detect broken inversion symmetry and local polar order. Analytical modeling of the SHG polarimetry of a nonlinear optical material is essential to extract its point group symmetry and the absolute nonlinear susceptibilities. Current literature on SHG analysis involves numerous approximations and a wide range of (in)accuracies. We have developed an open-source package called the Second Harmonic Analysis of Anisotropic Rotational Polarimetry (#SHAARP.si) which derives analytical and numerical solutions of reflection SHG polarimetry from a single interface (.si) for bulk homogeneous crystals with arbitrary symmetry group, arbitrary crystal orientation, complex and anisotropic linear dielectric tensor with frequency dispersion, a general SHG tensor and arbitrary light polarization. #SHAARP.si enables accurate modeling of polarimetry measurements in reflection geometry from highly absorbing crystals or wedge-shaped transparent crystals. The package is extendable to multiple interfaces.

36 MATERIALS SCIENCE↗

A numerical analysis of a magnetocaloric refrigerator with a 16-layer regenerator

A numerical analysis was conducted to study a room temperature magnetocaloric refrigerator with a 16-layer parallel plates active magnetic regenerator (AMR). Sixteen layers of LaFeMnSiH having different Curie temperatures were employed as magnetocaloric material (MCM) in the regenerator. Measured properties data was used. A transient one dimensional (1D) model was employed, in which a unique numerical method was developed to significantly accelerate the simulation speed of the multi-layer AMR system. As a result, the computation speed of a multi-layer AMR case was very close to the single-layer configuration. The performance of the 16-layer AMR system in different frequencies and utilizations has been investigated using this model. To optimize the layer length distribution of the 16-layer MCMs in the regenerator, a set of 137 simulations with different MCM distributions based on the Design of Experiments (DoE) method was conducted and the results were analyzed. The results show that the 16-layer AMR system can operate up to 84% of Carnot cycle COP at a temperature span of 41 K, which cannot be obtained using an AMR with fewer layers. Here, the DoE results indicate that for a 16-layer AMR system, the uniform distribution is very close to the optimized design.

36 MATERIALS SCIENCE↗

Beyond 30% Conversion Efficiency in Silicon Solar Cells: A Numerical Demonstration

We demonstrate through precise numerical simulations the possibility of flexible, thin-film solar cells, consisting of crystalline silicon, to achieve power conversion efficiency of 31%. Our optimized photonic crystal architecture consists of a 15 μm thick cell patterned with inverted micro-pyramids with lattice spacing comparable to the wavelength of near-infrared light, enabling strong wave-interference based light trapping and absorption. Unlike previous photonic crystal designs, photogenerated charge carrier flow is guided to a grid of interdigitated back contacts with optimized geometry to minimize Auger recombination losses due to lateral current flow. Front and back surface fields provided by optimized Gaussian doping profiles are shown to play a vital role in enhancing surface passivation. We carefully delineate the drop in power conversion efficiency when surface recombination velocities exceed 100 cm/s and the doping profiles deviate from prescribed values. These results are obtained by exact numerical simulation of Maxwell’s wave equations for light propagation throughout the cell architecture and a state-of-the-art model for charge carrier transport and Auger recombination.

14 SOLAR ENERGY↗