Radiative aspects of lunar materials Final report
Thermal radiation model for lunar materials
Adomian, G.↗
SEARCH · Engineering Papers
Results for “materials modelling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ten-year ground exposure of composite materials used on the Bell Model 206L helicopter flight service program
Residual strength results are presented for four composite material systems that have been exposed for up to 10 years to the environment at five different locations on the North American continent. The exposure locations are near where the Bell Model 206L helicopters, which participated in a flight service program sponsored by NASA Langley Research Center and the U.S. Army, were flying in daily commercial service. The composite material systems are (1) Kevlar-49 fabric/F-185 epoxy; (2) Kevlar-49 fabric/LRF-277 epoxy; (3) Kevlar-49 fabric/CE-306 epoxy; and (4) T-300 graphite/E-788 epoxy. Six replicates of each material were removed and tested after 1, 3, 5, 7, and 10 years of exposure. The average baseline strength was determined from testing six as-fabricated specimens. More than 1700 specimens have been tested. All specimens that were tested to determine their strength were painted with a polyurethane paint. Each set of specimens also included an unpainted panel for observing the weathering effects on the composite materials. A statistically based procedure has been used to determine the strength value above which at least 90 percent of the population is expected to fall with a 95-percent confidence level. The computed compression strengths are 80 to 90 percent of the baseline (no-exposure) strengths. The resulting compression strengths are approximately 8 percent below the population mean strengths. The computed short-beam-shear strengths are 83 to 92 percent of the baseline (no-exposure) strengths. The computed tension strength of all materials is 93 to 97 percent of the baseline (no-exposure) strengths.
Baker, Donald J.↗
A model for oblique impacts on material surfaces
Many practical situations of material damage, wear, and erosion involve collisions between small particles and surfaces at inclined angles. While there are many well-validated models of normal incidence impact situations, elastic-plastic models for oblique incidence impact events are lacking. Here the finite element method is used to predict the normal and tangential coefficient of restitution in oblique impacts for hard, elastic spheres impacting an elastic-perfectly plastic material surface. The proposed model covers various impact angles ranging from 0° to 45°, within a limiting impact velocity below which the effects of heating are negligible. The normal coefficient of restitution follows power-laws with respect to normalized values of the impact velocity. Interestingly, the tangential coefficient of restitution follows a linear relationship with impact velocity. Together, these results provide a semi-empirical set of equations predicting oblique impact rebounds (both velocity and trajectory) for a wide range of conditions and material properties, with which experimental results can be rapidly interpreted. As a result, Laser-Induced Particle Impact Test (LIPIT) data are also presented for aluminum particles impacting aluminum substrates, at impact angles of 25° and 40°; the results compare favorably with the model and validate the general use of such models for the analysis of experimental data.
Coefficient of restitution↗
Models and Algorithms for Equilibrium Analysis of Mixed-Material Nucleic Acid Systems
Dynamic programming algorithms within the NUPACK software suite enable analysis of equilibrium base-pairing properties for complex and test tube ensembles containing arbitrary numbers of interacting nucleic acid strands. Currently, calculations are limited to single-material systems that are either all-RNA or all-DNA. Here, to enable analysis of mixed-material systems that are critical for modern applications in vitro, in situ, and in vivo, we develop physical models and dynamic programming algorithms that allow the material of the system to be specified at nucleotide resolution. Free energy parameter sets are constructed for both RNA/DNA and RNA/2'OMe-RNA mixed-material systems by combining available empirical mixed-material parameters with single-material parameter sets to enable treatment of the full complex and test tube ensembles. New dynamic programming recursions account for the material of each nucleotide throughout the recursive process. For a complex with N nucleotides, the mixed-material dynamic programming algorithms maintain the O(N 3 ) time complexity of the single-material algorithms, enabling efficient calculation of diverse physical quantities over complex and test tube ensembles (e.g., complex partition function, equilibrium complex concentrations, equilibrium base-pairing probabilities, minimum free energy secondary structure(s), and Boltzmann-sampled secondary structures) at a cost increase of roughly 2.0-3.5×. The results of existing single-material algorithms are exactly reproduced when applying the new mixed-material algorithms to single-material systems. Accuracy is significantly enhanced using mixed-material models and algorithms to predict RNA/DNA and RNA/2'OMe-RNA duplex melting temperatures from the experimental literature as well as RNA/DNA melt profiles from new experiments. In conclusion, mixed-material analyses can be performed online using the NUPACK web app (www.nupack.org) or locally using the NUPACK Python module.
2′OMe-RNA↗
Overview of Elastic Orthotropic Fiber Reinforced Polymer Modular Damage Model for Library of Advanced Materials for Engineering (LAMÉ)
This memo includes the documentation sections for the Library of Advanced Materials for Engineering (LAMÉ) manual for a fiber reinforced polymer composite damage model (Elastic_Orthotropic_FRP_Modular_Damage) in advance of the next Sierra/SM and LAMÉ release consistent with the transition of the model from development to a production capability. This new model capability provides both a set of physically based orthotropic damage criteria as well as orthotropic material softening for woven fiber reinforced polymer composite materials. The documentation sections include short sections on theory, implementation, verification, and user guidance to prescribe the model in a Sierra/SM input file.
36 MATERIALS SCIENCE↗
The right conditions for high-precision dynamic temperature and heat capacity measurement via pyrometry and conductivity
The pursuit of accurate bulk temperature T under extreme conditions has been a long-standing goal of the high pressure science community, complicated by a lack of data to inform models. To reach these extremely high-pressure, high-temperature (high P − T) conditions, a combination of dynamic and heated static experiments (e.g., diamond or gem anvil cel experiments) are used. For example, in a diamond anvil cell (DAC) experiment, a sample placed in the DAC is first pressurized. Following pressurization, the sample T is increased either by heating the entire DAC (usually using resistive heating, and limited to ∼1000K) or by applying intense laser power to the sample surfaces. In a dynamic experiment, the process of pressurizing the sample also heats it. In the case of shock physics experiments, such heating is substantial, easily reaching thousands of Kelvin; in our work we have seen T ∼17000K. Most methods of measuring temperature at ambient are not compatible with experiments under these high-pressure, high-temperature conditions: thermocouples break, melt, or have conductivity properties that differ from ambient where they are calibrated; thermometers would melt; both are too slow. As a result most methods are based on non-contact techniques such as x-ray diffraction broadening, neutron scattering, or optical methods. Of these, optical methods using the visible and near-infrared region of the spectrum are the most commonly used as the sources and detectors are readily available. In the case of optical methods the optical depth, and therefore the measurement location, is limited to the surface. When a window or anvil material is used, heat flows from the sample into the window/anvil. Likewise, if the sample undergoes a change in thermodynamic state, such as expansion upon release, different T may be expected. As a result, the surface or apparent temperature T app measurement will differ from the bulk or interior temperature that is desired. This surface measurement must be related to the bulk measurement using thermal transport models and material models. While it is tempting to conclude that one should just use x-ray methods that directly probe the interior, even these methods have been shown to depend on thermal transport and material models. Regardless of the method used to create the high P − T condition, therefore, we must understand the role of thermal transport and material models upon our interpretation of the T measurement, as well as the errors and uncertainties associated with the choice of models used in the analysis. This is a substantial area of research and this paper is by no means a complete survey of the relevant sources of uncertainty. For example, we have yet to begin to address alternate transport models in a detailed manner (e.g., Tan-Ahrens), or the many models that use additional layers to approximate melting, turbulence, or epitaxial phenomena). Likewise, we have not explored the impact upon uncertainty of thermal models that use temperature-dependent thermal transport coefficients, or the wide range of material models that can be applied. Instead, this paper focuses on using one simple model, the Urtiew-Grover model, to understand the sources of error in T measurement so that we may identify how best to focus future research efforts to return the best improvements and avoid working on over-optimizing a single type of measurement. To this end, we work through some of the best and worst case scenarios for T measurement.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
A Model for Rate-Dependent Hysteresis in Piezoceramic Materials Operating at Low Frequencies
This paper addresses the modeling of certain rate-dependent mechanisms which contribute to hysteresis inherent to piezoelectric materials operating at low frequencies. While quasistatic models are suitable for initial material characterization in some applications, the reduction in coercive field and polarization values which occur as frequencies increase must be accommodated to achieve the full capabilities of the materials. The model employed here quantifies the hysteresis in two steps. In the first, anhysteretic polarization switching is modeled through the application of Boltzmann principles to balance the electrostatic and thermal energy. Hysteresis is then incorporated through the quantification of energy required to translate and bend domain walls pinned at inclusions inherent to the materials. The performance of the model is illustrated through a fit to low frequency data (0.1 Hz - 1 Hz) from a PZT5A wafer.
Smith, Ralph C.↗
FEA-aided investigation of the effective thermal conductivity in a medium with embedded spheres
For multiple applications in nuclear energy, the ability to accurately represent material behavior with a simplified model is important to facilitate practical engineering-scale simulations. Here, we focus on the homogenized thermal response of a medium containing spherical inclusions, similar to a fuel form (compact or pebble) containing (TRISO) particles. A review on effective thermal conductivity (ETC) modeling is performed considering a random distribution of mono-sized spherical inclusions in a continuous matrix, with a primary focus on the analytical models. Finite element simulations are performed to evaluate each analytical model in varying material conditions. The model predictions are compared with the expected results obtained from the finite element predictions in addition to the Wiener and Hashin-Shtrikman bounds. Lastly, we included a practical discussion on the homogenization applied to a TRISO fuel pebble.
42 ENGINEERING↗
Large language model-driven database for thermoelectric materials
Thermoelectric materials have the ability to convert waste heat into electricity, offering a valuable solution for energy harvesting. However, their widespread use is hindered by low conversion efficiency, the reliance on expensive rare earth elements, and the environmental and regulatory concerns associated with lead-based materials. A fast and cost-effective way to identify highly efficient thermoelectric materials is through data-driven methods. These approaches rely on robust and comprehensive datasets to train models. Although there are several databases on thermoelectric materials, there is still a need to collect and integrate experimental data from peer-reviewed research articles to capture diverse compositions and properties of materials. Here, in this work, we developed a comprehensive database of 7,123 thermoelectric compounds, containing key information such as chemical composition, structural detail, seebeck coefficient, electrical and thermal conductivity, power factor, and figure of merit (ZT). We used the GPTArticleExtractor workflow, powered by large language models (LLM), to extract and curate data automatically from the scientific literature published in Elsevier journals. This process enabled the creation of a structured database that addresses the challenges of manual data collection. The open access database could stimulate data-driven research and advance thermoelectric material analysis and discovery.
Database↗
Finite Element Analysis (FEA) for Water-Foam Fracturing of Granite Rock
In addition to the foam data that were obtained from literature and that were collected from the current study, simulation data was also generated from finite element analysis (FEA) conducted in this study using COMSOL Multiphysics software. The FEA models were built to simulate the experiments conducted at Oak Ridge National Laboratory (ORNL) on cement and granite samples. In these FEA models, temperature was kept at ambient while the pressure profile resembled the loading conditions during the ORNL experiments, where pressure was either monotonically increased or applied cyclically. The cement material was used as a model material and was used to study Von Mises stress and tensile stress distribution for different bore hole length geometry using a parametric sweep with water as fracturing fluid using solid-fluid interaction module. For the granite material, FEA models were developed for stress analysis of cylindrical samples with water or foam fluids. The solid mechanics module in COMSOL was implemented to solve for Von Mises stress and tensile stress. The fluid-structure interaction module was implemented to solve for water-foam interaction on granite cylinder with addition of fluid-loading on structure, i.e., large deformation in solid mechanics with no impact on fluid deformation. Foam was considered as a pseudo single-phase compressible fluid for which material properties were calculated from water and gas (nitrogen) phases. The density of foam is calculated as a function of the densities of water and nitrogen, while viscosity is a function of temperature. Four types of FEA analyses were modelled: 1. Monotonic injection with water 2. Monotonic injection with foam 3. Cyclic injection with water 4. Cyclic injection with foam All the COMSOL files are converted to a zip file which is save in .mph.
15 GEOTHERMAL ENERGY↗
Improved ceramic slip casting technique
A primary concern in modern fluid dynamics research is the experimental verification of computational aerothermodynamic codes. This research requires high precision and detail in the test model employed. Ceramic materials are used for these models because of their low heat conductivity and their survivability at high temperatures. To fabricate such models, slip casting techniques were developed to provide net-form, precision casting capability for high-purity ceramic materials in aqueous solutions. In previous slip casting techniques, block, or flask molds made of plaster-of-paris were used to draw liquid from the slip material. Upon setting, parts were removed from the flask mold and cured in a kiln at high temperatures. Casting detail was usually limited with this technique -- detailed parts were frequently damaged upon separation from the flask mold, as the molded parts are extremely delicate in the uncured state, and the flask mold is inflexible. Ceramic surfaces were also marred by 'parting lines' caused by mold separation. This adversely affected the aerodynamic surface quality of the model as well. (Parting lines are invariably necessary on or near the leading edges of wings, nosetips, and fins for mold separation. These areas are also critical for flow boundary layer control.) Parting agents used in the casting process also affected surface quality. These agents eventually soaked into the mold, the model, or flaked off when releasing the case model. Different materials were tried, such as oils, paraffin, and even an algae. The algae released best, but some of it remained on the model and imparted an uneven texture and discoloration on the model surface when cured. According to the present invention, a wax pattern for a shell mold is provided, and an aqueous mixture of a calcium sulfate-bonded investment material is applied as a coating to the wax pattern. The coated wax pattern is then dried, followed by curing to vaporize the wax pattern and leave a shell mold of the calcium sulfate-bonded investment material. The shell mold is cooled to room temperature, and a ceramic slip is poured therein. After a ceramic shell of desired thickness has set up in the shell mold, excess ceramic slip is poured out. While still wet, the shell mold is peeled from the ceramic shell to expose any delicate or detailed parts, after which the ceramic shell is cured to provide a complete, detailed, precision ceramic article without parting lines.
Buck, Gregory M.↗
Dispersive Dark Excitons in van der Waals Ferromagnet CrI 3
Spin-flip dark excitons are optical-dipole-forbidden quasiparticles with remarkable potential in optoelectronics, especially when they are realized within cleavable van der Waals materials. Despite this potential, dark excitons have not yet been definitively identified in ferromagnetic van der Waals materials. Here, we report two dark excitons in a model ferromagnetic material CrI 3 using high-resolution resonant inelastic x-ray scattering and show that they feature narrower linewidths compared to the bright excitons previously reported in this material. These excitons are shown to have spin-flip character, to disperse as a function of momentum, and to change through the ferromagnetic transition temperature. Given the versatility of van der Waals materials, these excitons hold promise for new types of magneto-optical functionality.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
ACT University Collaboration Proposal: Role of manufacturing defects on material failure under dynamic loading for developing enhanced failure models and theories (Final Report)
Research on the tensile behavior of additively manufactured 316L stainless steel coupon specimens at increasing strain rates was conducted over the past year at Penn State. Dynamic loading rates into the 1000 1/s loading rates were performed on specimens with nearly 1.32” gage lengths. Stress-strain plots show ductile and plastic behavior well beyond 12% strain with necked specimens, having smaller effective gage lengths showing up to 56% ultimate strain. Additional tests performed on compact tension specimens helped with simulation work to understand the deformation behavior. Using finite elements, it was possible to determine the feasibility of a comprehensive experimental validation study towards an improved model for AM material failure – specifically, the Bai-Wierzbicki approach which accounts for lode angle and triaxiality. A non-significant number of tests are projected for eight specific failure nodes, with additional replicates to provide strain-rate capabilities to the existing formulation. One such correction factor is explored for quasi-static, notched specimens. Finally, stress intensity factor was explored using a set of compact-tension specimens which would also provide useful validation data for any simulation work.
36 MATERIALS SCIENCE↗
Computing Reliabilities Of Ceramic Components Subject To Fracture
CARES calculates fast-fracture reliability or failure probability of macroscopically isotropic ceramic components. Program uses results from commercial structural-analysis program (MSC/NASTRAN or ANSYS) to evaluate reliability of component in presence of inherent surface- and/or volume-type flaws. Computes measure of reliability by use of finite-element mathematical model applicable to multiple materials in sense model made function of statistical characterizations of many ceramic materials. Reliability analysis uses element stress, temperature, area, and volume outputs, obtained from two-dimensional shell and three-dimensional solid isoparametric or axisymmetric finite elements. Written in FORTRAN 77.
Nemeth, N. N.↗
X-Ray Computed Tomography Inspection of the Stardust Heat Shield
The "Stardust" heat shield, composed of a PICA (Phenolic Impregnated Carbon Ablator) Thermal Protection System (TPS), bonded to a composite aeroshell, contains important features which chronicle its time in space as well as re-entry. To guide the further study of the Stardust heat shield, NASA reviewed a number of techniques for inspection of the article. The goals of the inspection were: 1) to establish the material characteristics of the shield and shield components, 2) record the dimensions of shield components and assembly as compared with the pre-flight condition, 3) provide flight infonnation for validation and verification of the FIAT ablation code and PICA material property model and 4) through the evaluation of the shield material provide input to future missions which employ similar materials. Industrial X-Ray Computed Tomography (CT) is a 3D inspection technology which can provide infonnation on material integrity, material properties (density) and dimensional measurements of the heat shield components. Computed tomographic volumetric inspections can generate a dimensionally correct, quantitatively accurate volume of the shield assembly. Because of the capabilities offered by X-ray CT, NASA chose to use this method to evaluate the Stardust heat shield. Personnel at NASA Johnson Space Center (JSC) and Lawrence Livermore National Labs (LLNL) recently performed a full scan of the Stardust heat shield using a newly installed X-ray CT system at JSC. This paper briefly discusses the technology used and then presents the following results: 1. CT scans derived dimensions and their comparisons with as-built dimensions anchored with data obtained from samples cut from the heat shield; 2. Measured density variation, char layer thickness, recession and bond line (the adhesive layer between the PICA and the aeroshell) integrity; 3. FIAT predicted recession, density and char layer profiles as well as bondline temperatures Finally suggestions are made as to future uses of this technology as a tool for non-destructively inspecting and verifying both pre and post flight heat shields.
McNamara, Karen M.↗
Characterization of Internal Insulation Thermal Performance
A test campaign was performed to build an SRM-insulation-material thermal-performance database using MSFC’s Solid Fuel Torch that could be leveraged to enhance understanding of the relationship between ablation rates and internal-environment parameters and improve insulation performance predictions. Seven hot-fire tests were performed along with data analysis that revealed the thermal performance differences among the tested materials. Functional Data Analysis was employed to create a model of material ablation rate as a function of six covariates. The relative importance of several environmental parameters was indicated, and the gaps in the operational space covered by the database were identified.
Ablation↗
Noninteractive macroscopic reliability model for ceramic matrix composites with orthotropic material symmetry
A macroscopic noninteractive reliability model for ceramic matrix composites is presented. The model is multiaxial and applicable to composites that can be characterized as orthotropic. Tensorial invariant theory is used to create an integrity basis with invariants that correspond to physical mechanisms related to fracture. This integrity basis is then used to construct a failure function per unit volume (or area) of material. It is assumed that the overall strength of the composite is governed by weakest link theory. This leads to a Weibull type model similar in nature to the principle of independent action (PIA) model for isotropic monolithic ceramics. An experimental program to obtain model parameters is briefly discussed. In addition, qualitative features of the model are illustrated by presenting reliability surfaces for various model parameters.
Duffy, Stephen F.↗
Noninteractive macroscopic reliability model for ceramic matrix composites with orthotropic material symmetry
A macroscopic noninteractive reliability model for ceramic matrix composites is presented. The model is multiaxial and applicable to composites that can be characterized as orthotropic. Tensorial invariant theory is used to create an integrity basis with invariants that correspond to physical mechanisms related to fracture. This integrity basis is then used to construct a failure function per unit volume (or area) of material. It is assumed that the overall strength of the composite is governed by weakest link theory. This leads to a Weibull type model similar in nature to the principle of independent action (PIA) model for isotropic monolithic ceramics. An experimental program to obtain model parameters is briefly discussed. In addition, qualitative features of the model are illustrated by presenting reliability surfaces for various model parameters.
Duffy, Stephen F.↗