Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Advanced methods for preparation and characterization of infrared detector materials

Mercury cadmium telluride crystals were prepared by the Bridgman method with a wide range of crystal growth rates and temperature gradients adequate to prevent constitutional supercooling under diffusion-limited, steady state, growth conditions. The longitudinal compositional gradients for different growth conditions and alloy compositions were calculated and compared with experimental data to develop a quantitative model of the crystal growth kinetics for the Hg(i-x)CdxTe alloys, and measurements were performed to ascertain the effect of growth conditions on radial compositional gradients. The pseudobinary HgTe-CdTe constitutional phase diagram was determined by precision differential thermal analysis measurements and used to calculate the segregation coefficient of Cd as a function of x and interface temperature. Computer algorithms specific to Hg(1-x)CdxTe were developed for calculations of the charge carrier concentrations, charge carrier mobilities, Hall coefficient, optical absorptance, and Fermi energy as functions of x, temperature, ionized donor and acceptor concentrations, and neutral defect concentrations.

Lehoczky, S. L.↗
NASA NTRS1981

Diagnostic study of BSF silicon solar cells

Solar cells equipped with back surface fields (BSF) were fabricated by means of an aluminum alloy, boron diffusion, and boron ion implantation. The importance of initial thickness, resistivity, orientation, and the crystal growth method were examined. Aluminum in paste form was screen printed on the cell, followed by alloy formation at 800 C for a minute. Application of the BSFs resulted in open circuit voltage improvements dependent on the substrate resistivity, ranging from 10 mV at 0.3 ohm-cm to 50 mV at 15 ohm-cm. The gains in performance were attributed to a longer penetration depth, a heightened concentration profile at the interface, and higher concentrations in the p+ layer.

Yoo, H.↗
NASA NTRS2018

Improved Pyrotechnic Shock Scaling Method Based on Shock Response Spectrum and Statistical Energy Analysis

It has been more than forty years since the pyrotechnic shock scaling method was introduced. The scaling method estimates the attenuation of the Shock Response Spectrum (SRS) based on the distance from the source, structural configurations, types of structural joints and interfaces, and intervening structure [1]. The method has been successfully used in the spacecraft community countless times and still is frequently used to develop pyrotechnic shock requirements at various levels of assembly of a spacecraft. However, since the method was derived empirically from a limited set of shock test data [2], the aerospace community has been looking for an alternative approach. In this paper, a computational scaling method based on Statistical Energy Analysis (SEA) is re-visited. SEA is traditionally used as a method for investigating the diffusion of acoustic and vibratory energies of a system at steady-state [3]. Previously, an approach using the SRS as an acceleration constraint condition to the SEA model was introduced to estimate the attenuation from a shock source [4,5]. In the current investigation, additional examples are provided to further validate the approach. In addition, responses in the time domain are produced by the Local Modal Phase Reconstruction (LMPR) approach which was recently introduced to the community [6].

Fernandez, Juan P.↗
DOE OSTI2023

CO 2 adsorption mechanisms at the ZIF-8 interface in a Type 3 porous liquid

Porous liquids (PLs) are an attractive material for gas separation and carbon sequestration due to their permanent internal porosity and high adsorption capacity. PLs that contain zeolitic imidazole frameworks (ZIFs), such as ZIF-8, form PLs through exclusion of aqueous solvents from the framework pore due to its hydrophobicity. The gas adsorption sites in ZIF-8 based PLs are historically unknown; gas molecules could be captured in the ZIF-8 pore or adsorb at the ZIF-8 interface. To address this question, ab initio molecular dynamics was used to predict CO 2 binding sites in a PL composed of a ZIF-8 particle solvated in a water, ethylene glycol, and 2-methylimidazole solvent system. Further, the results show that CO 2 energetically prefers to reside inside the ZIF-8 pore aperture due to strong van der Waals interactions with the terminal imidazoles. However, the CO 2 binding site can be blocked by larger solvent molecules that have greater adsorption interactions. CO 2 molecules were unable to diffuse into the ZIF-8 pore, with CO 2 adsorption occurring due to binding with the ZIF-8 surface. Therefore, future design of ZIF-based PLs for enhanced CO 2 adsorption should be based on the strength of gas binding at the solvated particle surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1980

Radiation damage in high voltage silicon solar cells

Three high open-circuit voltage cell designs based on 0.1 ohm-cm p-type silicon were irradiated with 1 MeV electrons and their performance determined to fluences as high as 10 to the 15th power/sq cm. Of the three cell designs, radiation induced degradation was greatest in the high-low emitter (HLE cell). The diffused and ion implanted cells degraded approximately equally but less than the HLE cell. Degradation was greatest in an HLE cell exposed to X-rays before electron irradiation. The cell regions controlling both short-circuit current and open-circuit voltage degradation were defined in all three cell types. An increase in front surface recombination velocity accompanied time dependent degradation of an HLE cell after X-irradiation. It was speculated that this was indirectly due to a decrease in positive charge at the silicon-oxide interface. Modifications aimed at reducing radiation induced degradation are proposed for all three cell types.

Weinberg, I.↗
NASA NTRS1980

Radiation damage in high voltage silicon solar cells

Three high open-circuit voltage cell designs based on 0.1 ohm-cm p-type silicon were irradiated with 1 MeV electrons and their performance determined to fluences as high as 10 to the 15th/sq cm. Of the three cell designs, radiation induced degradation was greatest in the high-low emitter (HLE) cell. The diffused and ion implanted cells degraded approximately equally but less than the HLE cell. Degradation was greatest in an HLE cell exposed to X-rays before electron irradiation. The cell regions controlling both short-circuit current and open-circuit voltage degradation were defined in all three cell types. An increase in front surface recombination velocity accompanied time dependent degradation of a HLE cell after X-irradiation. It was speculated that this was indirectly due to a decrease in positive charge at the silicon-oxide interface. Modifications aimed at reducing radiation induced degradation are proposed for all three cell types.

Weinberg, I.↗
DOE OSTI2022

Space-Time Block Preconditioning for Incompressible Flow

Parallel-in-time methods have become increasingly popular in the simulation of time-dependent numerical PDEs, allowing for the efficient use of additional message passing interface processes when spatial parallelism saturates. Most methods treat the solution and parallelism in space and time separately. In contrast, all-at-once methods solve the full space-time system directly, largely treating time as simply another spatial dimension. All-at-once methods offer a number of benefits over separate treatment of space and time, most notably significantly increased parallelism and faster time to solution (when applicable). However, the development of fast, scalable all-at-once methods has largely been limited to time-dependent (advection-)diffusion problems. This paper introduces the concept of space-time block preconditioning for the all-at-once solution of incompressible flow. By extending well-known concepts of spatial block preconditioning to the space-time setting, we develop a block preconditioner whose application requires the solution of a space-time (advection-)diffusion equation in the velocity block, coupled with a pressure Schur complement approximation consisting of independent spatial solves at each time-step, and a space-time matrix-vector multiplication. The new method is tested on four classical models in incompressible flow. Finally, the results indicate perfect scalability in refinement of spatial and temporal mesh spacing, perfect scalability in nonlinear Picard iteration count when applied to a nonlinear Navier--Stokes problem, and minimal overhead in terms of number of preconditioner applications compared with sequential time-stepping.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1998

The Effects of Ground and Space Processing on the Properties of Organic, Polymeric, and Colloidal Materials

In recent years, a great deal of interest has been directed toward the use of organic materials in the development of high-efficiency optoelectronic and phototonic devices. There is a myriad of possibilities among organic materials which allow flexibility in the design of unique structures with a variety of functional groups. The use of nonlinear optical (NLO) organic materials as thin film wave-guides allows full exploitation of their desirable qualifies by permitting long interaction lengths and large susceptibilities allowing modest power input. There are several methods in use to prepare thin films such as Langmuir-Blodgett (LB) and self-assembly techniques, vapor deposition, growth from sheared solution or melt, and melt growth between glass plates. Organic-based materials have many features that make them desirable for use in optical devices, such as high second-and third-order nonlinearity, flexibility of molecular design, and damage resistance to optical radiation. However, their use in devices has been hindered by processing difficulties for crystals and thin films. We discuss the potential role of microgravity processing of a few organic and polymeric materials. It is of interest to note how materials with second-and third-order NLO behavior may be improved in a diffusion-limited environment and ways in which convection may be detrimental to these materials. We focus our discussion on third-order materials for all-optical switching, and second-order materials for frequency conversion and electrooptics. The goal of minimizing optical loss obviously depends on processing methods. For solution-based processes, such as solution crystal growth and solution photopolymerization, it is well known that thermal and solutal density gradients can initiate buoyancy-driven convection. Resultant fluid flows can affect transport of material to and from growth interfaces and become manifest in the morphology and homogeneity of the growing film or crystal. Likewise, buoyancy-driven convection can hinder production of defect-free, high-quality crystals or films during crystal and film growth by vapor deposition.

Frazier, Donald O.↗
NASA NTRS2007

Increasing Durability of Flame-Sprayed Strain Gauges

Thermally sprayed dielectric ceramic coatings are the primary means of attaching strain and temperature gauges to hot-section rotating parts of turbine engines. As hot-section temperatures increase, lifetimes of installed gauges decrease, and seldom exceed one hour above 2,000 F (approx.1,100 C). Advanced engine components are expected to operate at temperatures approaching 2,200 F (approx.1,200 C), and the required high-temperature lifetime is 10 hours minimum. Typically, to enable a ceramic coating to adhere to the smooth surface of an engine component, a thermally sprayed NiCrAlY or NiCoCrAlY bond coat is applied to the smooth surface, thereby providing a textured surface to which the ceramic coat can adhere. The main failure mechanism of this system is decohesion and/or delamination at the interface between the ceramic top coat and the bond coat, caused by oxidation of the bond coat and stresses from the mismatch between the coefficients of thermal expansion of the ceramic top coat and the metallic bond coat. The approach taken to increase the high-temperature lifetime of a gauge attached to an engine component by the method described above involves (1) selective oxidation of the bond coat by means of a heat treatment in reduced oxygen partial pressure followed by (2) the application of a noble-metal diffusion barrier. In experiments to test this approach, heat treatments of NiCoCrAlY bond coats were carried out in a tube furnace in which, in each case, the temperature was alternately (1) increased at a rate of 3 C per minute and (2) held steady for one hour until the desired temperature was reached. The tube furnace was continuously purged with dry nitrogen gas. A final heat-treatment temperature range of 1,600 to 1,800 F (871 to 982 C) proved most beneficial.

Gregory, Otto J.↗
DOE OSTI2023

Differential multi-probe thermal transport measurements of multi-walled carbon nanotubes grown by chemical vapor deposition

Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m –1 K –1 at room temperature for a 9-walled MWCNT. In conclusion, theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.

42 ENGINEERING↗
DOE OSTI2020

Editors’ Choice—Flooded by Success: On the Role of Electrode Wettability in CO 2 Electrolyzers that Generate Liquid Products

Economic operation of carbon dioxide (CO 2 ) electrolyzers generating liquid products will likely require high reactant conversions and product concentrations, conditions anticipated to challenge existing gas diffusion electrodes (GDEs). Notably, electrode wettability will increase as lower surface tension products (e.g., formic acid, alcohols) are introduced into electrolyte streams, potentially leading to flooding. To understand the hydraulically stable operating envelopes in mixed aqueous-organic liquid domains, we connect intrinsic electrode wettability descriptors to operating parameters such as electrolyte flow rate and current. We first measure contact angles of water-organic product dilutions on polytetrafluoroethylene (PTFE) and graphite surfaces as planar analogues for GDE components. We then use material balances around the reactive gas-liquid-solid interface to calculate product mass fractions as functions of water sweep rate and current. Product composition maps visualize the extent to which changes in cell performance influence capillary pressure, a determinant of GDE saturation. Analyses suggest that formic acid mixtures pose little risk for GDE flooding across a wide range of conditions, but effluents containing <30% alcohol by mass may cause flooding. This study reveals opportunities to integrate microstructural features and oleophobic surface treatments into GDEs to repel aqueous-organic mixtures and expand the window of stable operating conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

MEUMAPPS (C++ Version)

Many materials, metal alloys in particular, have features on the on micrometer or nanometer scale that have a large impact on the properties of the material. These features are known as the microstructure of the material. Understanding why and how the microstructure forms in a material is of fundamental scientific interest as well as of significant technological interest. The capability to predict microstructure evolution in a material allows the intentional design of microstructures and hence the intentional design of material properties. The phase-field method is one of the leading methods for predicting microstructure evolution. One of the most significant problems for phase-field models is their computational expense. Even limited phase-field simulations can easily require thousands of CPU core-hours to complete, which significantly limits their use. This code provides both a general framework for creating scalable, GPU-accelerated phase-field model applications as well as several applications themselves. The code is capable of using hundreds of GPUs efficiently, which greatly reduces the time required to perform simulations. The code is written with an emphasis on performance portability, that is the ability for the code to run efficiently on a number of different computing architectures without modification of the source code. The performance portability of this code is primarily enabled through the use of two libraries, Kokkos (performance portable data structures and execution patterns) and heFFTe (performance portable distributed 3D fast Fourier transforms). The code consists of a core library, applications, and tests. The core library includes shared functionality between applications. This includes interfaces with fast Fourier transform (FFT) libraries such as heFFTe, data structures based on Kokkos, file input and output capabilities, and a solver for infinitesimal strain mechanical equilibrium problems. Five applications are included in the code. The flagship application is the MEUMAPPS-SS application, which implements the Kim-Kim-Suzuki phase-field model for precipitation for an arbitrary number of phases and components in a metal alloy. Five simpler applications are also included that solve the Eshelby inclusion problem, Allen-Cahn equation, the coupled Allen-Cahn and diffusion equations, and the Cahn-Hilliard equation. The code includes two applications to solve the Cahn-Hilliard equation, one with constant-step-size first-order time integration and the second with adaptive high-order time integration.

DeWitt, Stephen [Oak Ridge National Lab. (ORNL), O↗
NASA NTRS1994

Convection in the Physical Vapor Transport Process-I: Thermal

The effects of convection on diffusive-convective physical vapor transport process are examined computationally. We analyze conditions ranging from typical laboratory conditions to conditions achievable only in a low gravity environment. This corresponds to thermal Rayleigh numbers Ra, ranging from 1.80 x 10 to 1.92 x 10(exp 6). Our results indicate that the effect of the sublimation and condensation fluxes at the boundaries is to increase the threshold of instability. For typical ground based conditions, time dependent oscillatory convection can occur. This results in unsteady transport, and non- uniform temperature and concentration gradients at the crystal interface. Spectral analysis of the flow field shows parametric regions exhibiting both an oscillatory approach to steady state and a chaotic transient to a periodic state. Low gravity conditions stabilize the flow field. Convective effects are effectively reduced, thus resulting in uniform temperature and concentration gradients at the interface, a desirable condition for crystal growth.

Duval, Walter M. B.↗
DOE OSTI2025

Factors controlling injection-induced rupture of intersecting faults during geological sequestration of CO 2

This study addresses coupled multiphase fluid flow and geomechanics effects on potential fault activation associated with subsurface CO 2 injection around intersecting faults. An enhanced fault-representation model is used to capture geomechanical responses of two intersecting faults with finite length during CO 2 injection. The faults are embedded in a strike-slip stress regime of a caprock-reservoir-basement system with the faults represented by zero-thickness interfaces with adjacent finite-thickness damage zones. A sensitivity analysis is conducted to study the effect of fault permeability, slip-weakening behavior, well location relative to the orientation of faults, and well placement (the number and location of injection wells). Five metrics (pressure, CO 2 plume, shear state on the fault, as well as shear displacement and stress path at selected fault monitoring points) are selected to assess CO 2 migration and reactivation of intersecting faults. The results show that induced ruptures are favored by low permeability faults due to high pressure buildup and by slip-weakening behavior resulting from fault strength reduction. The location of one injection well relative to fault orientation determines the magnitude of changes in effective normal stress and shear stress, affecting the location of induced ruptures. Well placement (two injection wells used in the paper) dominates pressure diffusion around the intersection and tips of faults. This redistributes changes in effective normal stress caused by each injection well, influencing the spatial distribution of ruptures along faults. A larger injection volume induces far-field ruptures that are controlled by stress transfer within the injection layer. The findings presented here can provide valuable insights into engineering operations for a long-term, safe, and reliable geologic CO 2 storage.

Fault permeability↗
DOE OSTI2025

Stacking polymorphism of PtSe 2 : its implication to layer-dependent metal-insulator transitions

Using diffusion Monte Carlo (DMC) and density functional theory (DFT) calculations, we examine the structural stability and interlayer binding properties of PtSe 2 . Our DMC study reveals that AA and AB-r bilayer stacking modes are nearly degenerate, highlighting the significant role of interlayer hybridization in offsetting the energy cost due to larger interlayer separations in the AB-r mode. Additionally, our DMC-benchmarked DFT calculations with the r 2 SCAN+rVV10 functional uncover pronounced stacking polymorphism in few-layer PtSe 2 , driven by degenerate AA and AB-r interfaces, which leads to substantial band gap variations across different stacking configurations. This polymorphism, along with selenium vacancies, influences a layer-dependent metal-insulator transition observed in few-layer PtSe 2 . Our findings emphasize the importance of both van der Waals interactions and interlayer hybridization in determining the phase stability and electronic properties of PtSe 2 , advancing our understanding of its fundamental properties and refining theoretical models for practical applications in nanoelectronic devices.

Electronic materials↗
NASA NTRS1979

Trends and Techniques for Space Base Electronics

Simulations of various phosphorus and boron diffusions in SOS were completed and a sputtering system, furnaces, and photolithography related equipment were set up. Double layer metal experiments initially utilized wet chemistry techniques. By incorporating ultrasonic etching of the vias, premetal cleaning a modified buffered HF, phosphorus doped vapox, and extended sintering, yields of 98% were obtained using the standard test pattern. A two dimensional modeling program was written for simulating short channel MOSFETs with nonuniform substrate doping. A key simplifying assumption used is that the majority carriers can be represented by a sheet charge at the silicon dioxide silicon interface. Although the program is incomplete, the two dimensional Poisson equation for the potential distribution was achieved. The status of other Z-D MOSFET simulation programs is summarized.

Trotter, J. D.↗
NASA NTRS1998

Burner Emissions Associated with Lobed and Non-Lobed Fuel Injectors

The present experimental study examines NO(sub x), and CO emissions associated with three alternative fuel-injector geometries. These injectors mix fuel and air and strain their interfaces to differing extents and thus create different local equivalence ratios within flow regions upstream of flame ignition and stabilization. Two of the devices studied are lobed fuel injectors, in which molecular mixing of reactants is associated with streamwise vorticity generation, while the third one is a non-lobed fuel injector. Results show that rapid mixing allowed both lobed injector geometries to produce very lean premixed flame structures, with a lower achievable turn-down or fuel/air mass flux ratio than for the analogous non-lobed injector, which largely, produced distinct diffusion flames. All three injectors exhibited some level of sooting near walls and in the far-field region, with the non-lobed injector sooting to the greatest extent. At low fuel flow rates, in which the lobed injectors created locally very lean premixed conditions, there resulted lower NO(sub x) emissions as compared with non-lobed injector emissions. Yet at higher fuel-air mass flux ratios, NO(sub x) emissions from the lobed injectors were actually higher than for the nonlobed injector, likely due to reduced sooting and hence reduced radiative heat losses associated with enhanced mixing. For both lobed injector geometries examined here, CO emissions became high for low values of the fuel/air mass flux ratio, again consistent with locally premixed combustion behavior, despite the fact that fuel was injected separately from air directly into the burner test section. The present study demonstrates that, for fuel-air mixing enhancement devices, control of the local equivalence ratio is critical in order to optimize burner emissions.

Mitchell, M. G.↗
DOE OSTI2020

Exchange of Ions across the TiN/TaO x Interface during Electroformation of TaO x -Based Resistive Switching Devices

The valence change model describes the resistive switching in metal oxide-based devices as due to electroreduction of the oxide and subsequent electromigration of oxygen vacancies. Here, we present cross-sectional X-ray energy-dispersive spectroscopy elemental maps of Ta, O, N, and Ti in electroformed TiN/TaO 2.0 /TiN structures. O, N, and Ti were exchanged between the anode and the functional oxide in devices formed at high power (~1 mW), but the exchange was below the detection limit at low power (<0.5 mW). All structures exhibit a similar Ta-enriched and O-depleted filament formed by the elemental segregation in the functional oxide by the temperature gradient. The elemental interchange is interpreted as due to Fick’s diffusion caused by high temperatures in the gap of the filament and is not an essential part of electroformation.

36 MATERIALS SCIENCE↗