SEARCH · Engineering Papers

Results for “design process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Draft Rules for Alloy 617 Creep-Fatigue Design Using an EPP+SMT Approach

The report describes an improved new creep-fatigue design method for structural components in high temperature nuclear service. The new method uses an integrated elastic-perfectly plastic (EPP) analysis and Simplified Model Test (SMT) approach that greatly simplifies the design process by avoiding the separate evaluation of creep and fatigue damages and eliminating the requirement of stress classification. The report includes draft design rules, presented in a format compatible with an ASME nuclear Code Case, as well as a commentary on the rules and the validation of the rules using pressurized SMT (p-SMT) test data. Areas of potential improvement have been identified for further evaluation. The report also develops EPP+SMT design charts for Alloy 617 at temperatures between 800°C and 950°C by extrapolating high strain range, short hold test data to low strain range and long hold times, typical for structural components in high temperature nuclear service. The design charts are currently limited to 10,000 cycles to avoid excessive extrapolation outside the test database. More robust alternate extrapolation procedures will be considered in future work. The report includes several verification problems comparing the new EPP+SMT design method with current ASME creep-fatigue design methods. The comparison demonstrates that the EPP+SMT method significantly reduces the over-conservatism in current methods. Finally, the report includes a fully-documented sample problem with multiple load cases detailing the application of proposed EPP+SMT design rules.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Bench-scale Development of a Transformational Graphene Oxide-based Membrane Process for Post-combustion CO 2 Capture

Graphene-based materials, such as graphene and graphene oxide (GO), have been considered as next-generation membrane materials. GTI Energy and The State University of New York at Buffalo (UB) have been developing a transformational GO-based membrane process (designated as GO2) that integrates a high CO 2 /N 2 selectivity membrane (GO-1) and a high CO 2 flux membrane (GO-2) for post-combustion CO 2 capture. An innovative membrane structure, consisting of GO nanochannels intercalated by single-walled carbon nanotube (SWCNT), was developed. The membrane prepared on hollow fiber substrate showed CO 2 permeance as high as 1,300 GPU with CO 2 /N 2 selectivity >200. The membranes were successfully scaled up to effective area of 50-100 cm 2 . The 50-100 cm 2 membranes showed CO 2 /N 2 selectivity ≥200 and CO 2 permeance ≥1,000 GPU for the GO-1 type, and CO 2 /N 2 selectivity ≥20 and CO 2 permeance ≥2,500 GPU for the GO-2 type. The CO 2 capture performance of the GO-based membranes was tested using a simulated flue gas. The testing results indicate that the GO-based membranes are stable in the presence of flue gas contaminants. The GO-based membranes were then further scaled up to a surface area of 1,000 cm 2 . Good stability was achieved during an integrated testing with GO-1 and GO-2 membranes using simulated flue gas. A bench-scale system was designed, constructed, and tested at the National Carbon Capture Center (NCCC). Good stability was achieved during testing of a single-stage process with >10 shutdowns/startups at NCCC. During the integrated testing, the membranes showed good stability at 50°C and 57°C. 70-90% CO 2 removal efficiencies and ≥95% CO 2 purity were validated during the steady state operation at NCCC. Techno-economic analysis indicates the GO2 membrane-based process technology provides a reduction in both the levelized cost of electricity (LCOE) and cost of capture when compared to the reference B12B case presented in the Cost and Performance Baseline for Fossil Energy Plants Volume 1: Bituminous Coal and Natural Gas to Electricity study prepared by the National Energy Technology Laboratory (NETL), before considering any system optimization or improvement opportunities. The benefits are primarily driven by a reduction in the equipment costs of the CO 2 capture process vs. the solvent-based reference process in NETL Case B12B as well as a decrease in the base plant size.

20 FOSSIL-FUELED POWER PLANTS↗

NASA NTRS1990

Documenting the decision structure in software development

Current software development paradigms focus on the products of the development process. Much of the decision making process which produces these products is outside the scope of these paradigms. The Decision-Based Software Development (DBSD) paradigm views the design process as a series of interrelated decisions which involve the identification and articulation of problems, alternates, solutions and justifications. Decisions made by programmers and analysts are recorded in a project data base. Unresolved problems are also recorded and resources for their resolution are allocated by management according to the overall development strategy. This decision structure is linked to the products affected by the relevant decision and provides a process oriented view of the resulted system. Software maintenance uses this decision view of the system to understand the rationale behind the decisions affecting the part of the system to be modified. D-HyperCase, a prototype Decision-Based Hypermedia System is described and results of applying the DBSD approach during its development are presented.

Wild, J. Christian↗

NASA NTRS1991

Application of waverider-based configurations to hypersonic vehicle design

The hypersonic waverider concept is explored in the context of aircraft design and optimization. Waveriders are vehicles which provide the highest known values of lift-to-drag ratio, suggesting that they are ideal for hypersonic cruise applications. However, these high lift-to-drag ratios are not retained with engine integration. It is shown that waveriders may have applications to the design of accelerating vehicles, even though high L/D is no longer a priority, because they exhibit relatively low drag, and have highly desirable properties for engine/airframe integration. Along these lines, waveriders provide highly uniform flowfields, making them ideal for forebodies on engine-airframe integrated configurations. The inverse design methodology of a waverider lends itself readily to the vehicle design process. Characteristics which govern the performance of a hypersonic vehicle for cruise and accelerating flight are examined, and applied to waverider vehicle design. Finally, it is shown that waveriders, though configured for the specific shock flowfield of a single design point, have acceptable off-design performance characteristics.

Lewis, Mark J.↗

NASA NTRS1999

Advanced Technology Inlet Design, NRA 8-21 Cycle II: DRACO Flowpath Hypersonic Inlet Design

The report outlines work performed in support of the flowpath development for the DRACO engine program. The design process initiated to develop a hypersonic axisymmetric inlet for a Mach 6 rocket-based combined cycle (RBCC) engine is discussed. Various design parametrics were investigated, including design shock-on-lip Mach number, cone angle, throat Mach number, throat angle. length of distributed compression, and subsonic diffuser contours. Conceptual mechanical designs consistent with installation into the D-21 vehicle were developed. Additionally, program planning for an intensive inlet development program to support a Critical Design Review in three years was performed. This development program included both analytical and experimental elements and support for a flight-capable inlet mechanical design.

Sanders, Bobby W.↗

NASA NTRS2004

Printed Circuit Board Design (PCB) with HDL Designer

Contents include the following: PCB design with HDL designer, design process and schematic capture - symbols and diagrams: 1. Motivation: time savings, money savings, simplicity. 2. Approach: use single tool PCB for FPGA design, more FPGA designs than PCB designers. 3. Use HDL designer for schematic capture.

Winkert, Thomas K.↗

NASA NTRS2004

Modelling and Analysis of a Regenerative Fuel Cell Propulsion System for a High Altitude Long Endurance UAV

In the search to bridge current gaps in surveillance and communication technologies, a new type of, aircraft is currently undergoing design. The idea of a High Altitude Long Endurance (HALE) aircraft is already a few decades old, but has only recently become realizable. A relay and collector of information at altitudes of 65,000 feet and higher could greatly improve standards of data exchange, homeland security, and research of the air, land and sea. NASA, as a major force in propulsion research, is exploring methods of powering an autonomous aircraft for days, weeks, or even months without refueling. Such a task requires not only high energy density, but also the ability to make use of renewable energy sources to regenerate power. Hydrogen is one of the most energy dense fuels available. Fuel cells make use of hydrogen by harnessing the energy released as it combines with oxygen to produce electricity and water. Fuel cells are envisioned to occupy future propulsion systems in cooperation with solar cells where the photovoltaic arrays harness sunlight into power which can electrolize the water byproduct into reusable hydrogen and oxygen. Modeling this type of system requires adequate assumptions of support hardware and daily transients in operation. The performance of a regenerative fuel cell propulsion system lies in the flight characteristics (altitude, density, temperature, latitude, etc.). Each subsystem is defined by many parameters which can be varied across wide ranges. Statistical and probabilistic analyses bring forward a wealth of information that can be utilized in the design process. This is necessary since the required technologies are relatively young and barely, if yet, capable. Once the modeling is complete, a design space exploration of this highly constrained scenario can be utilized to find the optimal design. The model will become an interactive environment with which experiments and tests can be run. When linked

Simpson, Mike B.↗

NASA NTRS2006

Rapid Assessment of Aircraft Structural Topologies for Multidisciplinary Optimization and Weight Estimation

Algorithms for rapid generation of moderate-fidelity structural finite element models of air vehicle structures to allow more accurate weight estimation earlier in the vehicle design process have been developed. Application of these algorithms should help to rapidly assess many structural layouts before the start of the preliminary design phase and eliminate weight penalties imposed when actual structure weights exceed those estimated during conceptual design. By defining the structural topology in a fully parametric manner, the structure can be mapped to arbitrary vehicle configurations being considered during conceptual design optimization. Recent enhancements to this approach include the porting of the algorithms to a platform-independent software language Python, and modifications to specifically consider morphing aircraft-type configurations. Two sample cases which illustrate these recent developments are presented.

Samareh, Jamshid A.↗

NASA NTRS2008

Multidisciplinary Design, Analysis, and Optimization Tool Development using a Genetic Algorithm

Multidisciplinary design, analysis, and optimization using a genetic algorithm is being developed at the National Aeronautics and Space A dministration Dryden Flight Research Center to automate analysis and design process by leveraging existing tools such as NASTRAN, ZAERO a nd CFD codes to enable true multidisciplinary optimization in the pr eliminary design stage of subsonic, transonic, supersonic, and hypers onic aircraft. This is a promising technology, but faces many challe nges in large-scale, real-world application. This paper describes cur rent approaches, recent results, and challenges for MDAO as demonstr ated by our experience with the Ikhana fire pod design.

Pak, Chan-gi↗

NASA NTRS2020

The New NASA Approach to Reliability and Maintainability

In 2017, after 20 years, NASA issued a major revision of its reliability and maintainability (R&M) policy, NASA-STD- 8729.1A. Formerly NASA required certain specific R&M activities during each succeeding phase of project development. Now NASA requires a project to start by including the initial development of R&M requirements and the devising of strategies to implement and verify them. Rather than resolving all the requirements first and then designing the system, as has been usual in systems design, the design process now is to work top down by layers. It begins by first identifying the top level requirements and suggesting top level design strategies for those, then making these higher strategies the basis for a lower level set of requirements, and so on down to the lowest components. This approach is intended to ensure that R&M is designed in from the beginning rather than added later with difficulty to a completed design concept. The new R&M standard uses an innovative and effective top-down system design approach intended to effectively implement R&M.

Jones, Harry W.↗

NASA NTRS2020

The New NASA Approach to Reliability and Maintainability

In 2017, after 20 years, NASA issued a major revision of its reliability and maintainability (R&M) policy, NASA-STD-8729.1A [1]. Formerly NASA required certain specific R&M activities during each succeeding phase of project development. Now NASA requires a project to start by including the initial development of R&M requirements and the devising of strategies to implement and verify them. Rather than resolving all the requirements first and then designing the system, as has been usual in systems design, the design process now is to work top down by layers. It begins by first identifying the top level requirements and suggesting top level design strategies for those, then making these higher strategies the basis for a lower level set of requirements, and so on down to the lowest components. This approach is intended to ensure that R&M is designed in from the beginning rather than added later with difficulty to a completed design concept. The new R&M standard uses an innovative and effective top-down system design approach intended to effectively implement R&M.

Jones, Harry W.↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircraft

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

SUSAN Electro-Fan Aircraft↗

NASA NTRSDate not supplied

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircrafts

Electric Aircraft↗

DOE OSTI2021

Flattening the Radial Temperature Profile across the Transformational Challenge Reactor Core

The Transformational Challenge Reactor (TCR) program is demonstrating an agile development approach to advanced nuclear reactor design, which has traditionally utilized a linear design process. In leveraging artificial intelligence, additive manufacturing, advanced materials, and cutting-edge modeling and simulation, the TCR program aims to minimize the high cost and lengthy deployment timelines now standard in the nuclear industry. Within a relatively short period of time, a robust and mature advanced gas-cooled reactor was iteratively designed under the TCR program, using these cutting-edge technologies. The TCR is a 3 MWt gas-cooled microreactor fueled with uranium nitride (UN) tristructural isotropic (TRISO) fuel particles. Though manufactured via traditional means, these UN TRISO particles are loaded into additively manufactured silicon carbide (SiC) cans [4]. Once loaded with TRISO particles, the SiC cans are densified using a chemical vapor infiltration process. The additively manufactured SiC enables significantly more freedom in the design of the fuel form than could ever be achieved using traditionally manufactured SiC. The helium coolant, pressurized to 5 MPa, enters the core at 300°C and nominally exits it at 500°C. Typically, the most thermally limiting components in any reactor design are the fuel assemblies in the core center. To provide a wide thermal margin in these central fuel assemblies, the flow may be biased toward the center of the core to more effectively cool these fuel assemblies with more power deposition and flatten the core’s radial temperature distribution. An analytical fluid model of the TCR core was developed to explore methods for biasing the flow away from the cooler outer fuel assemblies and towards the hotter inner ones. Higher-fidelity models developed in STAR-CCM+ 2020.3.1, a computational fluid dynamics code, were then utilized to verify the analytical model’s findings.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRSDate not supplied

Semantic Search with Sentence-BERT for Design Information Retrieval

Managing and referencing design knowledge is a critical activity in the design process. However, reliably retrieving useful knowledge can be a frustrating experience for users of knowledge management systems due to inherent limitations of standard keyword-based searches. In this research, we consider the task of retrieving relevant lessons learned from the NASA Lessons Learned Information System (LLIS). To this end, we apply a state-of-the-art natural language processing (NLP) technique for information retrieval (IR): semantic search with sentence-BERT, which is a modification of a Bidirectional Encoder Representations from Transformers (BERT) model that uses siamese and triplet network architectures to obtain semantically meaningful sentence embeddings. While the pre-trained sBERT model performs well out-of-the-box, we further fine-tune the model on data from the LLIS so that it learns on design engineering-relevant vocabulary. We quantify the improvement in query results using both standard sBERT and fine-tuned sBERT over a keyword search. Our use case throughout the paper is to use queries related to specific requirements from a NASA project. Fine tuning the sBERT model on LLIS data yields a mean average precision (MAP) of 0.807 on queries based on information needs from a real NASA project. Results indicate that applying state-of-the-art natural language processing techniques, especially when finetuned using engineering data, to design information retrieval tasks shows significant promise in modernizing design knowledge management systems.

Hannah S. Walsh↗

NASA NTRS2011

Human Rating the Orion Parachute System

Human rating begins with design. Converging on the requirements and identifying the risks as early as possible in the design process is essential. Understanding of the interaction between the recovery system and the spacecraft will in large part dictate the achievable reliability of the final design. Component and complete system full-scale flight testing is critical to assure a realistic evaluation of the performance and reliability of the parachute system. However, because testing is so often difficult and expensive, comprehensive analysis of test results and correlation to accurate modeling completes the human rating process. The National Aeronautics and Space Administration (NASA) Orion program uses parachutes to stabilize and decelerate the Crew Exploration Vehicle (CEV) spacecraft during subsonic flight in order to deliver a safe water landing. This paper describes the approach that CEV Parachute Assembly System (CPAS) will take to human rate the parachute recovery system for the CEV.

Machin, Ricardo A.↗

NASA NTRS1981

Process characteristics and design methods for a 300 deg quad OP amp

The results of process characterization, circuit design, and reliability studies for the development of a quad OP amplifier intended for use up to 300 C are presented. A dielectrically isolated complementary vertical bipolar process was chosen to fabricate the amplifier in order to eliminate isolation leakage and the possibility of latch up. Characterization of NPN and PNP junctions showed them to be suitable for use up to 300 C. Interconnect reliability was predicted to be greater than four years mean time between failure. Parasitic MOS formation was eliminated by isolation of each device.

Beasom, J. D.↗

DOE OSTI2026

A mathematical design framework for membrane pre-concentration in energy-efficient recovery of fermentation products

Due to the dilute nature of products manufactured via fermentation and cell-free bioprocessing, dewatering is a common unit operation in downstream processing (DSP) for bioproduct recovery, but it is typically energy intensive. To improve DSP energy efficiency for bio-based small molecules, integrating high-pressure membrane pre-concentration is a promising process option. However, this approach is typically constrained by a tradeoff between concentration factor (CF) and product recovery (PR), namely increasing the CF typically results in greater product loss, and vice versa. Here we developed a model that enables process design guidelines to: (i) identify scenarios in which the additional energy consumption and product loss from membrane pre-concentration are justified for use in DSP, and (ii) determine the optimal CF that minimizes process specific energy consumption. We compared the energy consumption of high-pressure membrane-integrated processes to evaporation-only processes and applied the model to an experimental case study for the separation and purification of butyric acid from Clostridium tyrobutyricum fermentation using an in situ product recovery (ISPR) process. The model estimated that integrating a tangential-flow reverse osmosis (RO) pre-concentration unit could reduce process energy consumption up to 45%. The use of advanced membrane pre-concentration technologies, such as negative rejection membranes and organic solvent reverse osmosis (OSRO), have the potential to further reduce the overall process specific energy consumption up to 96%, projected based on modeling. Overall, membrane pre-concentration, especially when strategically integrated prior to an evaporation step with optimized process conditions, holds significant potential for improving DSP energy efficiency, particularly in applications requiring substantial solvent removal for product recovery from dilute mixtures.

09 BIOMASS FUELS↗