Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Blended-Wing-Body Transonic Aerodynamics: Summary of Ground Tests and Sample Results

The Blended-Wing-Body (BWB) concept has shown substantial performance benefits over conventional aircraft configuration with part of the benefit being derived from the absence of a conventional empennage arrangement. The configuration instead relies upon a bank of trailing edge devices to provide control authority and augment stability. To determine the aerodynamic characteristics of the aircraft, several wind tunnel tests were conducted with a 2% model of Boeing's BWB-450-1L configuration. The tests were conducted in the NASA Langley Research Center's National Transonic Facility and the Arnold Engineering Development Center s 16-Foot Transonic Tunnel. Characteristics of the configuration and the effectiveness of the elevons, drag rudders and winglet rudders were measured at various angles of attack, yaw angles, and Mach numbers (subsonic to transonic speeds). The data from these tests will be used to develop a high fidelity simulation model for flight dynamics analysis and also serve as a reference for CFD comparisons. This paper provides an overview of the wind tunnel tests and examines the effects of Reynolds number, Mach number, pitch-pause versus continuous sweep data acquisition and compares the data from the two wind tunnels.

Carter, Melissa B.↗
NASA NTRS1990

Pressure fluctuations in the tip region of a blunt-tipped airfoil

The characteristics of turbulence generated in the tip region of a blunt-tipped airfoil were studied using surface pressure measurements. The model was a NACA 0012; tests were performed at flow speeds of 75, 55, and 35 m/s and angles of attack of 6, 12, and 16 deg. Reynolds numbers based on the wing chord were 1.9, 3.0, and 4.1 million. Pressure fluctuations measured near the primary tip-vortex on the upper, low pressure side of the wing tip were uncorrelated with those on the blunt tip. Fluctuations on the high pressure side of the wing were strongly correlated with those on the flat tip, but 10-20 dB less intense. Spectra measured on the flat tip displayed pronounced peaks at dimensionless frequencies of 0.8 to 1.3. Cross correlations between some of the flat-tip pressures displayed two echolike groupings. A model is proposed that explains these correlations.

Mcinerny, S. A.↗
NASA NTRS1983

Subsonic high-angle-of-attack aerodynamic characteristics of a cone and cylinder with triangular cross sections and a cone with a square cross section

Experiments were conducted in the 12-Foot Pressure Wind Tunnel at Ames Research Center on three models with noncircular cross sections: a cone having a square cross section with rounded corners and a cone and cylinder with triangular cross sections and rounded vertices. The cones were tested with both sharp and blunt noses. Surface pressures and force and moment measurements were obtained over an angle of attack range from 30 deg to 90 deg and selected oil-flow experiments were conducted to visualize surface flow patterns. Unit Reynolds numbers ranged from 0.8x1,000,000/m to 13.0x1,000,000/m at a Mach number of 0.25, except for a few low-Reynolds-number runs at a Mach number of 0.17. Pressure data, as well as force data and oil-flow photographs, reveal that the three dimensional flow structure at angles of attack up to 75 deg is very complex and is highly dependent on nose bluntness and Reynolds number. For angles of attack from 75 deg to 90 deg the sectional aerodynamic characteristics are similar to those of a two dimensional cylinder with the same cross section.

Clarkson, M. H.↗
NASA NTRS1974

Dynamic stall modeling and correlation with experimental data on airfoils and rotors

Two methods for modeling dynamic stall have been developed. The alpha, A, B method generates lift and pitching moments as functions of angle of attack and its first two time derivatives. The coefficients are derived from experimental data for oscillating airfoils. The Time Delay Method generates the coefficients from steady state airfoil characteristics and an associated time delay in stall beyond the steady state stall angle. Correlation with three types of test data shows that the alpha, A, B method is somewhat better for use in predicting helicopter rotor response in forward flight. Correlation with lift and moment hysteresis loops generated for oscillating airfoils was good for both models.

Carlson, R. G.↗
NASA NTRS1982

Three-dimensional flow calculations including boundary layer effects for supersonic inlets at angle of attack

An analysis is presented for calculating the steady three-dimensional flow field in supersonic mixed-compression inlets at incidence. A zonal modeling approach is employed to obtain the solution. The supersonic core flow is computed using a second-order pentahedral bicharacteristic algorithm. The bow shock wave and the reflected internal shock train are determined using a three-dimensional discrete shock fitting procedure. The boundary layer flow adjacent to both the centerbody and the cowl is computed using a second-order implicit finite difference method. The flow in a shock wave-boundary layer interaction region is computed using an integral formulation. The culmination of the present research effort is the development of a production-type computer program capable of analyzing flow in a variety of mixed-compression aircraft inlets. Numerical results and experimental correlations are presented to illustrate application of the analysis.

Vadyak, J.↗
NASA NTRS1979

An experimental and theoretical investigation of the effect of nonmetric over-the-wing nacelles on wing-body aerodynamics

Drag reduction benefits due to blowing the jet exhausts over the wing for a transport-type wing-body configuration were investigated in the Langley 16-foot transonic tunnel. A combination of a wing-body model and a powered-nacelle test rig was tested at Mach numbers of 0.50 and 0.80 at angles of attack from -2 degrees to 4 degrees and jet total-pressure ratios from jet off to 3 or 4 (depending on Mach number) for a variety of nacelle locations relative to the wing. The experimental results were compared with the predictions obtained from several theoretical techniques. It was concluded that positioning of the nacelles (nonmetric) can have large effects on the wing-body drag. Some positions yielded higher drag than the baseline position, whereas others yielded lower drag than the baseline position. The theoretical method which utilized a quasi-vortex-lattice for the wing and wing-jet interaction in combination with a jet entrainment model gave generally reasonable predictions of the drag increments.

Reubush, D. E.↗
NASA NTRSDate not supplied

Exploring Airfoil Table Generation using XFOIL and OVERFLOW

The rotorcraft design process is a continuously evolving field of research that incorporates a number of software programs. An accurate airfoil table is critical in the design and testing process for rotorcraft. With multiple flow solvers available and flow conditions of multirotor UAM vehicles potentially covering a wide range of Reynolds and Mach numbers, a documented approach for developing airfoil tables is needed. Using benchmark data from legacy airfoil tables and wind tunnel tests for comparison, simulations for a comprehensive test matrix could guide rotorcraft design engineers in generating their own airfoil tables using the XFOIL and OVERFLOW solvers. The motivation for this study is to investigate flow solver features to develop a best practices document for airfoil table generation. The study uses the OVERFLOW and XFOIL flow solvers, coupled with the airfoil table generator AFTGen, to analyze three airfoils for a specific Reynolds numbers flow regime and provide details on how well each flow solver performs within a specific angle of attack range, Mach number range, Reynolds number range, and in different flow conditions, such as turbulent and transitional flow. OVERFLOW analyses in AFTGen for fully turbulent and transition flow are compared with XFOIL results and experimental test data for the section lift, section drag, and pressure coefficients. XFOIL ultimately yields results that are accurate within the linear angle of attack range and below a Mach number of 0.4 but tends to overpredict lift and underpredict drag unless the flow is in the compressible regime. XFOIL cannot accurately model stall and post-stall conditions due to the nature of the solver. This is evident in nearly every case run with XFOIL, where the linear range is usually predicted acceptably and the lift coefficient is overpredicted as the stall angle of attack is approached (with the exception being the generally poor correlation with most of the SSC-A09 cases). OVERFLOW is limited at low Mach numbers, and appears to perform best at Mach numbers of 0.4 and above. The exploration of airfoil table generation using XFOIL and OVERFLOW yielded moderately successful results for the NACA 0012 airfoil, reasonably good results for the RC(4)-10 airfoil, and less accurate results for the SSC-A09 airfoil.

Airfoil Table Generation↗
NASA NTRSDate not supplied

Implementation and Verification of the SST-𝜸 and SA-AFT Transition Models in FUN3D

The transition modeling capability in the NASA unstructured FUN3D suite of codes has been augmented by incorporating two additional transport-equation-based transition models, namely, the 𝜸 transition model coupled with Menter’s 2003 Shear-Stress Transport (SST) turbulence model and Coder’s Amplification Factor Transport (AFT) transition model combined with the Spalart-Allmaras (SA) turbulence model. Both of these models, SST-𝜸 and SA-AFT, are used to compute transition characteristics of several test cases from the literature. The selected test cases cover a range of transition scenarios including bypass transition over a flat plate (ERCOFTAC T3A and T3A- flow configurations), transition in the presence of separation bubbles (NLF-0416 airfoil at selected angles of attack), and natural transition due to Tollmien-Schlichting instabilities (flat-plate experiment by Schubauer and Klebanoff). To address the urgent need for model verification as highlighted in recent workshops on transition modeling, the drag, lift, surface pressure, and skin-friction coefficients from the FUN3D solutions for a sequence of meshes are compared with the results obtained with the same models implemented in the NASA structured grid flow solver OVERFLOW. Comparisons between the local and global surface coefficients from the FUN3D and OVERFLOW solvers for all test cases resulted in good agreement for the finest meshes.

Verification↗
NASA NTRS1979

Miniature flow-direction and airspeed sensor for airplanes and radio controlled models in spin studies

A miniature flow direction and airspeed sensor was developed for use on 1/10- to 1/15 scale models and on full-scale airplanes engaged in spin research. The range of flow angles encountered in spinning flight (+ or - 120 degrees in angle of attack and + or - 55 degrees in sideslip) is larger than that of normal flight. These angles, along with an effective airspeed range of 9 to 90 m/sec, were measured with static accuracies of + or - 0.35 degrees for angle of attack, + or - 0.25 degrees for sideslip angle, and + or - 1 m/sec for airspeed. The dynamic accuracy is adequate to measure the rapidly changing flow angles and airspeed without singificant distortion. The sensor is rugged enough to withstand both the airplane environment and that of the radio-controlled, unpowered models.

Kershner, D. D.↗
NASA NTRS1980

Wind tunnel investigation of an all flush orifice air data system for a large subsonic aircraft

The results of a wind tunnel investigation on an all flush orifice air data system for use on a KC-135A aircraft are presented. The investigation was performed to determine the applicability of fixed all flush orifice air data systems that use only aircraft surfaces for orifices on the nose of the model (in a configuration similar to that of the shuttle entry air data system) provided the measurements required for the determination of stagnation pressure, angle of attack, and angle of sideslip. For the measurement of static pressure, additional flush orifices in positions on the sides of the fuselage corresponding to those in a standard pitot-static system were required. An acceptable but less accurate system, consisting of orifices only on the nose of the model, is defined and discussed.

Larson, T. J.↗
NASA NTRS1983

Effect of external stores on the stability and control characteristics of a delta wing fighter model at Mach numbers from 0.60 to 2.01

An investigation has been made to determine the effects of external stores on the stability and control characteristics of a delta wing fighter airplane model at Mach numbers from 0.60 to 2.01 for a Reynolds number of 3.0 X 1 million per foot. The angle-of-attack range was from about -4 degrees to 20 degrees at a sideslip angle of 0 degrees for the transonic tests, and from about -4 degrees to 10 degrees at sideslip angles of 0 degrees and 3 degrees for the supersonic tests. In general, the results of the tests indicated no seriously detrimental effects of the stores on the stability and control characteristics of the model but did show an increase in the minimum drag level throughout the Mach number range. However, the drag-due-to-lift was such that for subsonic/transonic speeds, the drag at higher lifts was essentially unaffected and the indications are that the maneuvering capability may not be impaired by the stores.

Spearman, M. L.↗
NASA NTRS1972

Assessment of potential buffet problems on the space shuttle vehicle

Buffet of the space shuttle launch and reentry configuration is an area requiring continued evaluation to produce a safe reliable vehicle of minimum weight. Buffet forces result from flow separation and therefore can not be predicted accurately. Buffet loads are highly sensitive to configuration, angle of attack, and Mach number and can be reliably determined only by wind tunnel tests of elastically scaled models.

Muhlstein, L., Jr.↗
NASA NTRS1973

Local skin friction coefficients and boundary layer profiles obtained in flight from the XB-70-1 airplane at Mach numbers up to 2.5

Boundary-layer and local friction data for Mach numbers up to 2.5 and Reynolds numbers up to 3.6 x 10 to the 8th power were obtained in flight at three locations on the XB-70-1 airplane: the lower forward fuselage centerline (nose), the upper rear fuselage centerline, and the upper surface of the right wing. Local skin friction coefficients were derived at each location by using (1) a skin friction force balance, (2) a Preston probe, and (3) an adaptation of Clauser's method which derives skin friction from the rake velocity profile. These three techniques provided consistent results that agreed well with the von Karman-Schoenherr relationship for flow conditions that are quasi-two-dimensional. At the lower angles of attack, the nose-boom and flow-direction vanes are believed to have caused the momentum thickness at the nose to be larger than at the higher angles of attack. The boundary-layer data and local skin friction coefficients are tabulated. The wind-tunnel-model surface-pressure distribution ahead of the three locations and the flight surface-pressure distribution ahead of the wing location are included.

Fisher, D. F.↗
NASA NTRS1974

Results of investigations on an 0.004-scale 140A/B configuration space shuttle vehicle orbiter model (34-0) in the NASA/Langley Research Center hypersonic helium tunnel (OA88)

Data obtained during a wind tunnel test of an 0.004-scale 140A/B configuration SSV Orbiter are reported. The test was conducted at a nominal Mach number of 20 and at Reynolds numbers of 0.7, 1.1, 2.0, and 4 x 10 to the 6th power per foot. The complete 140A/B model was tested with various elevon settings and additionally in wing off/bodyflap off configurations at angles of attack from 18 to 54 degrees at zero yaw. This test was performed to obtain high hypersonic longitudinal and lateral-directional stability and control characteristics of the SSV configuration.

Hawthorne, P. J.↗
NASA NTRS1976

Supersonic dynamic-stability derivatives of the space shuttle launch vehicle

An investigation was made to determine the dynamic stability characteristics of a 0.015-scale model of the space shuttle launch vehicle at supersonic speeds. These tests were made at angles of attack from -10 deg to 10 deg at Mach numbers of 2.00, 2.86, 3.96, and 4.63. The complete launch vehicle, consisting of the orbiter, external tank, and solid rocket boosters, has positive damping in pitch, roll, and yaw over the angle-of-attack and Mach number range. The orbiter external tank configuration has a region of negative angles pitch damping for small negative of attack at a Mach number of 2.00. At all other test conditions, the orbiter external tank configuration has positive damping about all three axes.

Boyden, R. P.↗
NASA NTRS1978

Static aerodynamic characteristics of a winged single-stage-to-orbit vehicle at Mach numbers from 0.3 to 4.63

The Langley 8 foot transonic pressure tunnel and the Langley Unitary Plan wind tunnel used to determine the longitudinal and lateral-directional aerodynamic characteristics of a winged single-state-to-orbit vehicle was investigated. The model was tested over a Mach number range from 0.3 to 4.63 for an angle-of-attack range from 4 to 30 D at both 0 and 5 D sideslip.

Freeman, D. C., Jr.↗
NASA NTRS1978

Control-surface hinge-moment calculations for a high-aspect-ratio supercritical wing

The hinge moments, at selected flight conditions, resulting from deflecting two trailing edge control surfaces (one inboard and one midspan) on a high aspect ratio, swept, fuel conservative wing with a supercritical airfoil are estimated. Hinge moment results obtained from procedures which employ a recently developed transonic analysis are given. In this procedure a three dimensional inviscid transonic aerodynamics computer program is combined with a two dimensional turbulent boundary layer program in order to obtain an interacted solution. These results indicate that trends of the estimated hinge moment as a function of deflection angle are similar to those from experimental hinge moment measurements made on wind tunnel models with swept supercritical wings tested at similar values of free stream Mach number and angle of attack.

Perry, B., III↗
NASA NTRS1983

Effects of nacelle position and shape on performance of subsonic cruise aircraft

The reduction of installed-propulsion-system drag by installing circular and D-shaped-cross-section nacelles in an underwing-aft position is investigated experimentally in the NASA-Langley 16-foot transonic wind tunnel. Measurements were made at Mach 0.70 to 0.85, -2.5 to 4.1-deg angle of attack, and 3.4 to 4.0 million/ft Reynolds numbers using the NASA USB full-span transonic transport model; and results were compared with those for the wing-body and underwing-forward/pylon-mounted-nacelle (UTW) configurations. While all nacelle configurations are found to have interference drag, which can probably be reduced by eliminating supersonic flows, both aft configurations are shown to reduce drag relative to UTW and increase lift coefficients. The aft D-nacelle had the lowest drag, 6.8 percent of airplane drag lower than UTW at Mach 8.0 and lift coefficient 0.45. Wing pressure distributions and the effects of deflectors are discussed.

Bangert, L. H.↗