Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “airfoil”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

A Feasibility Study to Control Airfoil Shape Using THUNDER

The objective of this study was to assess the capabilities of a new out-of-plane displacement piezoelectric actuator called thin-layer composite-unimorph ferroelectric driver and sensor (THUNDER) to alter the upper surface geometry of a subscale airfoil to enhance performance under aerodynamic loading. Sixty test conditions, consisting of combinations of five angles of attack, four dc applied voltages, and three tunnel velocities, were studied in a tabletop wind tunnel. Results indicated that larger magnitudes of applied voltage produced larger wafer displacements. Wind-off displacements were also consistently larger than wind-on. Higher velocities produced larger displacements than lower velocities because of increased upper surface suction. Increased suction also resulted in larger displacements at higher angles of attack. Creep and hysteresis of the wafer, which were identified at each test condition, contributed to larger negative displacements for all negative applied voltages and larger positive displacements for the smaller positive applied voltage (+102 V). An elastic membrane used to hold the wafer to the upper surface hindered displacements at the larger positive applied voltage (+170 V). Both creep and hysteresis appeared bounded based on the analysis of several displacement cycles. These results show that THUNDER can be used to alter the camber of a small airfoil under aerodynamic loads.

Pinkerton, Jennifer L.↗
NASA NTRS1981

Transonic Flow Past a Symmetrical Airfoil at High Angle of Attack

The results of an experimental investigation of shock-induced stall and leading-edge stall on a 64A010 airfoil section are presented. Advanced nonintrusive techniques - laser velocimetry and holographic interferometry - were used in characterizing the inviscid and viscous flow regions. The measurements include Mach contours of the inviscid now regions, and mean velocity, flow direction, and Reynolds shear stress profiles in the separated regions. The experimental observations of this study are relevant to efforts to improve surface-pressure prediction methods for airfoils at or near stall.

Johnson, D. A.↗
NASA NTRS1959

Chordwise Pressure Distributions over Several NACA 16-Series Airfoils at Transonic Mach Numbers up to 1.25

A two-dimensional wind-tunnel investigation of the pressure distributions over several NACA 16-series airfoils with thicknesses of 4, 6, 9, and 12 percent of the chord and design lift coefficients of 0, 0.2, 1 and 0.5 has been conducted in the Langley airfoil test apparatus at transonic Mach numbers from 0.7 to 1.25. The tests ranged in Reynolds number from 2.4 x 10 (exp 6) to 2.8 x 10 (exp 6) and in angle of attack from -10 to 12 degrees. Chordwise pressure distributions and schlieren flow photographs are presented without analysis.

Ladson, Charles L.↗
NASA NTRS1981

Calculation of Unsteady Transonic Flow over an Airfoil

An implicit finite-difference solver for either the Euler equations or the "thin-layer" Navier-Stokes equations was used to calculate a transonic flow over the NACA 64A010 airfoil pitching about its one-quarter chord. An unsteady automatic grid-generation procedure that will improve significantly the computational efficiency of various unsteady flow problems is described. The calculated results for both inviscid and viscous flows at Much number 0.8 over the airfoil oscillating with reduced frequency referenced to one-half chord, 0.2, are compared with experimental data measured in the Ames 11 x 11-ft Transonic Wind Tunnel. Nonlinear, unsteady effects of the flow on the surface pressure variations, shock-wave excursions, and overall airloads are examined. Good agreements between the results of computations and experiments were obtained. In the shock-wave region, however, the results of the viscous-flow computations showed closer agreement with the experimental data.

Chyu, W. J.↗
NASA NTRS1981

Calculation of Unsteady Transonic Flow Over an Airfoil

An implicit finite-difference solver for either the Euler equations or the "thin-layer" Navier-Stokes equations was used to calculate a transonic flow over the NACA 64A010 airfoil pitching about its one-quarter chord. An unsteady automatic grid-generation procedure that will improve significantly the computational efficiency of various unsteady flow problems is described. The calculated results for both inviscid and viscous flows at Mach number 0.8 over the airfoil oscillating with reduced frequency referenced to one-half chord, 0.2, are compared with experimental data measured in the Ames 11 x 11 ft Transonic Wind Tunnel. Nonlinear, unsteady effects of the flow on the surface pressure variations, shock-wave excursions, and overall airloads are examined. Good agreements between the results of computations and experiments were obtained. In the shock-wave region, however, the results of the viscous-flow computations showed closer agreement with the experimental data.

Chyu, W. J.↗
NASA NTRS1997

Airfoil Design Using a Coupled Euler and Integral Boundary Layer Method with Adjoint Based Sensitivities

The objective of this paper is to present a control theory approach for the design of airfoils in the presence of viscous compressible flows. A coupled system of the integral boundary layer and the Euler equations is solved to provide rapid flow simulations. An adjunct approach consistent with the complete coupled state equations is employed to obtain the sensitivities needed to drive a numerical optimization algorithm. Design to target pressure distribution is demonstrated on an RAE 2822 airfoil at transonic speed.

Edwards, S.↗
NASA NTRS2000

ICEG2D: An Integrated Software Package for Automated Prediction of Flow Fields for Single-Element Airfoils with Ice Accretion

An integrated software package, ICEG2D, was developed to automate computational fluid dynamics (CFD) simulations for single-element airfoils with ice accretion. ICEG2D is designed to automatically perform three primary functions: (1) generating a grid-ready, surface definition based on the geometrical characteristics of the iced airfoil surface, (2) generating a high-quality grid using the generated surface point distribution, and (3) generating the input and restart files needed to run the general purpose CFD solver NPARC. ICEG2D can be executed in batch mode using a script file or in an interactive mode by entering directives from a command line. This report summarizes activities completed in the first year of a three-year research and development program to address issues related to CFD simulations for aircraft components with ice accretion. Specifically, this document describes the technology employed in the software, the installation procedure, and a description of the operation of the software package. Validation of the geometry and grid generation modules of ICEG2D is also discussed.

Thompson, David S.↗
NASA NTRS1999

Smagglce: Surface Modeling and Grid Generation for Iced Airfoils: Phase 1 Results

SmaggIce (Surface Modeling and Grid Generation for Iced Airfoils) is a software toolkit used in the process of aerodynamic performance prediction of iced airfoils with grid-based Computational Fluid Dynamics (CFD). It includes tools for data probing, boundary smoothing, domain decomposition, and structured grid generation and refinement. SmaggIce provides the underlying computations to perform these functions, a GUI (Graphical User Interface) to control and interact with those functions, and graphical displays of results, it is being developed at NASA Glenn Research Center. This paper discusses the overall design of SmaggIce as well as what has been implemented in Phase 1. Phase 1 results provide two types of software tools: interactive ice shape probing and interactive ice shape control. The ice shape probing tools will provide aircraft icing engineers and scientists with an interactive means to measure the physical characteristics of ice shapes. On the other hand, the ice shape control features of SmaggIce will allow engineers to examine input geometry data, correct or modify any deficiencies in the geometry, and perform controlled systematic smoothing to a level that will make the CFD process manageable.

Vickerman, Mary B.↗
NASA NTRS2000

Ice Accretions and Icing Effects for Modern Airfoils

Icing tests were conducted to document ice shapes formed on three different two-dimensional airfoils and to study the effects of the accreted ice on aerodynamic performance. The models tested were representative of airfoil designs in current use for each of the commercial transport, business jet, and general aviation categories of aircraft. The models were subjected to a range of icing conditions in an icing wind tunnel. The conditions were selected primarily from the Federal Aviation Administration's Federal Aviation Regulations 25 Appendix C atmospheric icing conditions. A few large droplet icing conditions were included. To verify the aerodynamic performance measurements, molds were made of selected ice shapes formed in the icing tunnel. Castings of the ice were made from the molds and placed on a model in a dry, low-turbulence wind tunnel where precision aerodynamic performance measurements were made. Documentation of all the ice shapes and the aerodynamic performance measurements made during the icing tunnel tests is included in this report. Results from the dry, low-turbulence wind tunnel tests are also presented.

Addy, Harold E., Jr.↗
NASA NTRS2000

Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2% and 7%) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains non-turbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re = 50,000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence and intermittency profiles are presented.

Volino, Ralph J.↗
NASA NTRS2000

The Surface Pressure Response of a NACA 0015 Airfoil Immersed in Grid Turbulence: Characteristics of the Turbulence - Volume 1

Two grids have been developed for the Virginia Tech 6 ft x 6 ft Stability wind tunnel for the purpose of generating homogeneous isotropic turbulent flows for the study of unsteady airfoil response. The first, a square bi-planar grid with a 12" mesh size and an open area ratio of 69.4%, was mounted in the wind tunnel contraction. The second grid, a metal weave with a 1.2 in. mesh size and an open area ratio of 68.2% was mounted in the tunnel test section. Detailed statistical and spectral measurements of the turbulence generated by the two grids are presented for wind tunnel free stream speeds of 10, 20, 30 and 40 m/s. These measurements show the flows to be closely homogeneous and isotropic. Both grids produce flows with a turbulence intensity of about 4% at the location planned for the airfoil leading edge. Turbulence produced by the large grid has an integral scale of some 3.2 inches here. Turbulence produced by the small grid is an order of magnitude smaller. For wavenumbers below the upper limit of the inertial subrange, the spectra and correlations measured with both grids at all speeds can be represented using the von Karman interpolation formula with a single velocity and length scale. The spectra maybe accurately represented over the entire wavenumber range by a modification of the von Karman interpolation formula that includes the effects of dissipation. These models are most accurate at the higher speeds (30 and 40 m/s).

Bereketab, Semere↗
NASA NTRS2000

Geometry Modeling and Grid Generation for "Icing Effects" and "Ice Accretion" Simulations on Airfoils

There are two distinct icing-related problems for airfoils that can be simulated. One is predicting the effects of ice on the aerodynamic performance of airfoils when ice geometry is known ("icing effects" study). The other is simulating ice accretion under specified icing conditions ("ice accretion" simulation). This paper will address development of two different software packages for two-dimensional geometry preparation and grid generation for both "icing effects" and "ice accretion" studies.

Choo, Yung↗
NASA NTRS2000

Single Airfoil Gust Response Problem

An unsteady aerodynamic code, called GUST3D, has been developed to solve the single, non-constant coefficient, inhomogeneous convective wave equation for flows with periodic vortical disturbance. The code uses a frequency-domain approach with second-order central differences and a Sommerfeld radiation condition in the far field. It has been extensively validated on model problems with analytical solutions. GUST3D requires as input certain mean flow quantities which are calculated separately by a potential flow solver. This solver calculates the mean flow using a Gothert's Rule approximation. On the airfoil surface, it uses the solution calculated by the potential code FL036. A figure shows the mean pressure along the airfoil surface. To calculate the unsteady pressure, GUST3D was run oil systematically refined grids to obtain a converged solution at each frequency. It was found that 24 points per wavelength was sufficient for convergence. The location of the outer grid boundary was also varied to check for sensitivity to the far-field boundary condition.

Scott, James R.↗
NASA NTRS2000

Analytical Solutions to the Unsteady Response of an Isolated Finite Span Swept Airfoil to an Incident Gust and Unsteady Response of a Rectilinear Swept Cascade to an Incident Gust Problems

The solution to the problem of unsteady response of an isolated finite span swept airfoil to an incident gust is most conveniently obtained by introducing an acoustic velocity potential and eliminating all primitive variables from the governing equations. The end result is the convected wave equation for the acoustic velocity potential, phi. For the unsteady response of a rectilinear swept cascade to an incident gust problem, the governing equation and the imposed boundary conditions are the same as those for the isolated airfoil problem.

Envia, Edmane↗
NASA NTRS1999

Computational Modeling for the Flow Over a Multi-Element Airfoil

The flow over a multi-element airfoil is computed using two two-equation turbulence models. The computations are performed using the INS2D) Navier-Stokes code for two angles of attack. Overset grids are used for the three-element airfoil. The computed results are compared with experimental data for the surface pressure, skin friction coefficient, and velocity magnitude. The computed surface quantities generally agree well with the measurement. The computed results reveal the possible existence of a mixing-layer-like region of flow next to the suction surface of the slat for both angles of attack.

Liou, William W.↗
NASA NTRS2001

A Study of Ice Accretion Physics to Improve the Ice Accretion on Airfoils

This three-year grant began on November 7, 1996 and was no-cost extended to end on October 30, 2000. The objectives of the grant were: (1) To examine the effect of wind tunnel turbulence on ice accretion; (2) To determine the relationship between ice accretion geometry and airfoil performance; and (3) To determine if the wake-survey method was an appropriate experimental technique for iced-airfoil drag measurement. As specified in the grant the primary deliverables for this research were annual reports in the form of AIAA papers presented at national meetings each year. Masters theses and annual oral reports to be given at NASA Lewis (now Glenn) were also deliverables. Six AIAA papers documented the research findings from this study, Mr. Chad Henze's Masters thesis describes the wind tunnel turbulence work in detail, and a summary of the icing wind tunnel turbulence work was published in the archival AIAA Journal of Aircraft. A brief summary of the findings is given. Please refer to the reports for the details of the studies and findings.

Bragg, Michael B.↗
NASA NTRS1996

Control of Flow Separation Using Adaptive Airfoils

A novel way of controlling flow separation is reported. The approach involves using an adaptive airfoil geometry that changes its leading edge shape to adjust to the instantaneous flow at high angles of attack such that the flow over it remains attached. In particular, a baseline NACA 0012 airfoil, whose leading edge curvature could be changed dynamically by 400% was tested under quasi-steady compressible flow conditions. A mechanical drive system was used to produce a rounded leading edge to reduce the strong local flow acceleration around its nose and thus reduce the strong adverse pressure gradient that follows such a rapid acceleration. Tests in steady flow showed that at M = 0.3, the flow separated at about 14 deg. angle of attack for the NACA 0012 profile but could be kept attached up to an angle of about 18 deg by changing the nose curvature. No significant hysteresis effects were observed; the flow could be made to reattach from its separated state at high angles by changing the leading edge curvature.

Chandrasekhara, M. S.↗
NASA NTRS2002

Turbomachinery Airfoil Design Optimization Using Differential Evolution

An aerodynamic design optimization procedure that is based on a evolutionary algorithm known at Differential Evolution is described. Differential Evolution is a simple, fast, and robust evolutionary strategy that has been proven effective in determining the global optimum for several difficult optimization problems, including highly nonlinear systems with discontinuities and multiple local optima. The method is combined with a Navier-Stokes solver that evaluates the various intermediate designs and provides inputs to the optimization procedure. An efficient constraint handling mechanism is also incorporated. Results are presented for the inverse design of a turbine airfoil from a modern jet engine and compared to earlier methods. The capability of the method to search large design spaces and obtain the optimal airfoils in an automatic fashion is demonstrated. Substantial reductions in the overall computing time requirements are achieved by using the algorithm in conjunction with neural networks.

Madavan, Nateri K.↗