Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WASHING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Assessing the nexus between groundwater and solar energy plants in a desert basin with a dual-model approach under uncertainty

Globally, many solar power plants and other types of renewable energy are being located in water-scarce regions. Many projects rely on groundwater resources whose sustainability is uncertain. In the Chuckwalla Basin in California, quantification of recharge and trans-valley underflow is needed to estimate the impacts of solar project withdrawals on the water table. However, such estimates are highly challenging due to data scarcity, heterogeneous soils and long residence times. Conventional assessment employs isolated groundwater models configured with crude and uniform estimates of recharge. Here, we employ a data-constrained surface subsurface processes model, PAWS+CLM, to provide an ensemble of recharges and underflows with perturbed parameters. Then, the Parameter Estimation (PEST) package is used to calibrate MODFLOW aquifer conductivity and filter out implausible recharges. The novel dual-model approach, potentially applicable in other arid regions, can effectively assimilate groundwater head observations, reject unrealistic parameters, and narrow the range of estimated drawdowns. Simulated recharge concentrates along alluvial fans at the mountain fronts and ephemeral washes where run-off water infiltrates. If an evenly distributed recharge was assumed, it resulted in under-estimated drawdown and larger uncertainty bounds. The withdrawals are approaching total inflow, suggesting the system will be nearing, if not exceeding, its sustainable groundwater production capacity, and a boom of such projects will not be sustainable. Especially, the cost/benefit of pumped-storage projects is called into question as the initial-fill phase depletes entire area’s recharge. Our study highlights the stress on groundwater resources of solar development, and that the speed of groundwater recovery does not indicate sustainability.

14 SOLAR ENERGY↗

Microfluidic Cell-based Assays in Stem Cell and Other Rare Cell Type Research

Microfluidics is a technology defined by the engineered precise manipulation of minute amount of liquids through channels with dimensions in the micron scale. Much of microfluidic devices used for biomedical purposes are produced in the form of so called “lab-on-a-chip” format, where multiple steps of conventional biochemical analyses such as staining, washing, and signal collection are miniaturized and integrated into chips fabricated from polymer or glass. Cell-based microfluidic lab-on-achip technology provides some obvious advantages: 1) drastically reduced sample and reagent requirement, and 2) separation and detection with improved sensitivity due to fluid properties at the microscale, i.e. laminar flow. Based on these two advantages, the obvious place where microfluidic cell assays will provide the most benefit is wherescientists must gather much information from precious little sample. Stem cells and other precious cell types such as circulating tumor cells (CTCs), and rare immune subsets are the perfect match for microfluidic multiplex assays. The recent demonstration that multiple cellular changes such as surface receptor activation, protein translocation, long and short RNA, and DNA changes can all be extracted from intact single cells paves the way to systems level understanding of cellular states during development or disease. Finally, with the ability to preserve cell integrity in a microfluidic device during multiplexed analysis, one also preserves the single cell resolution, where information regarding the cell-to-cell heterogeneity during differentiation or response to stimuli is vitally important.

59 BASIC BIOLOGICAL SCIENCES↗

Moisture Protection of Electronics

Moisture is a key contributor to a variety of electronic system failure modes. These failure modes range from corrosion to surface flashover on printed circuit boards due to moist surface contaminants. One particularly challenging aspect of moisture-induced failures is the intermittent nature of the problems. As a result, troubleshooting can result in the removal of parts that subsequently retest as acceptable. This can generate a large volume of suspect parts, and can significantly increase the consumption rate of spares. In outdoor environments, or wet indoor environments like wash-down areas, best practices for moisture protection of electronic systems begin with the design of the enclosures and penetrations, and end with the design and configuration of the electronic components. Several of these best practices are presented in this article.

Hostick, Cody J.↗

Waste Management Approach for a Potential Future U.S. Closed Fuel Cycle - 16233

The U.S. Department of Energy, Office of Nuclear Energy has chartered an effort to develop technologies to enable safe and cost effective recycle of commercial used nuclear fuel (UNF) in the U.S. Part of this effort includes the evaluation of exiting waste management technologies for effective treatment of wastes in the context of current U.S. regulations and development of waste forms and processes with significant cost and/or performance benefits over those existing. This study summarizes the results of these ongoing efforts with a focus on the highly radioactive primary waste streams. The primary streams considered and the recommended waste forms include: •Tritium separated from either a low volume gas stream or a high volume water stream. The recommended waste form is low-water cement in high integrity containers. •Iodine-129 separated from off-gas streams in aqueous processing. There are a range of potentially suitable waste forms. As a reference case, a glass composite material (GCM) formed by the encapsulation of the silver Mordenite (AgZ) getter material in a low-temperature glass is assumed. A number of alternatives with distinct advantages are also considered including a fused silica waste form with encapsulated nano-sized AgI crystals. •Carbon-14 separated from LWR fuel treatment off-gases and immobilized as a CaCO3 in a cement waste form. •Krypton-85 separated from LWR and SFR fuel treatment off-gases and stored as a compressed gas. •An aqueous reprocessing high-level waste (HLW) raffinate waste which is immobilized by the vitrification process in one of three forms: a single phase borosilicate glass, a borosilicate based glass ceramic, or a multi-phased titanate ceramic [e.g., synthetic rock (Synroc)]. •An undissolved solids (UDS) fraction from aqueous reprocessing of LWR fuel that is either included in the borosilicate HLW glass or is immobilized in the form of a metal alloy in the case of glass ceramics or titanate ceramics. •Zirconium-based LWR fuel cladding hulls and stainless steel (SS) fuel assembly hardware that are washed and super-compacted for disposal or as an alternative Zr purification and reuse (or disposal as low-level waste, LLW) by reactive gas separations. •Electrochemical process salt HLW which is immobilized in a glass bonded Sodalite waste form known as the ceramic waste form (CWF). •Electrochemical process UDS and SS cladding hulls which are melted into an iron based alloy waste form. Mass and volume estimates for each of the recommended waste forms based on the source terms from a representative flowsheet are reported.

Fuel Cycle↗

Domestic Dishwasher Simulated Energy Efficiency Evaluation Using Thermoelectric Heat Pump for Water Heating and Dish Drying

A quasi-steady state, heat and mass transfer lumped-capacitance model was developed to predict the energy consumption and drying performance of domestic dishwashers. A numerical finite element solution was applied, assuming that the following components could each be treated as a lumped thermal capacitance: dish load, tub, wash water, and air in tub. The model was used to predict the energy consumption savings of heating water using a thermoelectric heat pump that extracts heat from a thermal storage medium, and the drying performance of circulating tub air through the cold and then hot side of TE modules.

Abuheiba, Ahmad↗

Method of making medium density fiberboard

The present invention provides a method for producing an MDF board from pulp from a fibrous lignocellulose material using a treatment or pretreatment step which exposes the material to oxalic acid or oxalic acid derivatives (particularly dialkyl ester derivatives, particularly in the vapor phase). The treated wood is then subjected to a sugar extraction wash and refined using any one of the several pulping methods to produce a final pulp product. Once this is done the pulp is used to make MDF boards having improved water repellency properties.

Akhtar, Masood↗

Favorable impact of RMP ELM suppression on divertor heat fluxes at ITER-like conditions

Small current modulations in a subset of DIII-D I-coils were used in RMP ELM suppression experiments at ITER-like conditions (shape, collisionality, RMP spectrum) to control position of the divertor particle and heat fluxes. Qualitative agreement was found between measured HFS particle flux striations and modeling of magnetic footprints with and without ideal MHD plasma response. However, the radial separation of the particle flux striations is 4-7x larger than the modeled splitting. Striations are generally not observed in the divertor heat flux to the inner strike point in RMP ELM suppression at ITER-like conditions; this is understood to be due to an increase in the volumetric carbon radiation in the inner divertor which washes out the striations in the heat flux to the inner strike point. This suggests that radiative divertor operations in ITER may avoid striated peaks. The divertor target plate heat flux can be reduced 2–3x, with a 60% radiated power fraction, by establishing a narrow radiating mantle between 0.95 ≤ Ψ N ≤ 1. This is achieved without the loss of ELM suppression by using neon or argon injection into the main chamber. These radiating mantle discharges show for the first time that ELM suppression can be maintained over a wide range of pedestal collisionalities (0.1 < ν$^{&middot;}_e$ < 1.1) with only a modest increase in the line average electron density.

Orlov, D. M.↗

Vertical Gradients in Fluidized Sand Columns

This study evaluated the influence of diameter and grain size on the initiation and continuation phase of piping erosion. Twelve tests were performed in a laboratory setting in which sand was fluidized in a controlled setting and hydraulic gradients within the sand, flow rates through the sand, and expansion of the sand columns were measured as the sand was fluidized. This study was conducted to improve the understanding of the resistance a vertical column of sand offers to piping erosion. From the fluidization tests conducted in two permeameters with different diameters, it cannot be concluded that permeameter diameter has a significant influence on a specimen’s resistance to piping erosion. Although one test conducted in the smaller diameter permeameter did record hydraulic gradients lower than those recorded in tests conducted in the larger diameter permeameter, this was not a consistent observation for all tests run in the smaller diameter permeameter. Further analysis ought to involve more tests run in each permeameter as well as incorporating additional permeameters with both larger and smaller diameters than those used in this study. From the fluidization tests conducted using the well-graded, coarse-, medium-, and fine-grained sands, it appears that resistance to piping is dependent on grain size and grain size distribution. The coarse-grained sand offered the most resistance to piping, the fine-grained sand offered the least, and the medium-grained and well-graded sands offered similar resistances between those of the coarse-grained and fine-grained sands. Gradients at which sand boils were observed, maximum gradients reached before the sand fluidized, and the minimum gradients reached at the conclusion of each test also appear to be influenced by grain size and grain size distribution. Tests conducted on the coarse-grained sand recorded the highest and most closely spaced sand boil, maximum, and minimum gradients, indicating that it offered the highest and most constant resistance to piping, while the fine-grained sand tests recorded the lowest sand boil, maximum, and minimum gradients, indicating that it offered the least resistance to piping and that resistance decreased as the tests progressed. The medium-grained sand tests recorded sand boil, maximum, and minimum gradients between those of the coarse-grained and fine-grained sands. The well-graded sand tests recorded the lowest sand boil gradient, which could be indicative of the occurrence of suffusion erosion occurring in conjunction with piping erosion, whereby the finer particles were washed out of the sand matrix at relatively low gradients, forming sand boils while the relatively coarser matrix remained resistant to piping. All tests recorded maximum gradients that were lower than the theoretical critical gradients calculated using Equation 4. This is likely due to the changes in the internal configuration of the sand as the piping process 33 initiates. In order to better understand the influence of gradation on resistance to piping, more sand gradations should be tested in future work. Measured hydraulic gradients in the lower portion of the fluidized sands were higher than those measured in higher portions. This could be explained if the density of the fluidized sand was not uniform, with more material near the base of the column than near the top, which is contrary to the findings of Sellmeijer. Furthermore, the tests were terminated when the maximum height of the upstream reservoir was reached but did not give any evidence that gradients had leveled off to a uniform “final gradient”. It is likely that gradients would have continued to dissipate had more hydraulic head been applied to the upstream reservoir. In order to better understand this, additional testing should be conducted using an upstream reservoir capable of simulating higher hydraulic heads.

13 HYDRO ENERGY↗

10 Point Monitoring Strategy

Presented at the IRAD-Advanced Course for Israel in Wash DC at RSLA during Feb 25-Mar 1, 2019

61 RADIATION PROTECTION AND DOSIMETRY↗

Contamination Control

For the IRAD-Advanced Course for Israel in Wash DC at RSLA during Feb 25-Mar 1, 2019.

61 RADIATION PROTECTION AND DOSIMETRY↗

BETO 2021 Peer Review - Enzyme Engineering and Optimization (EEO)

The FY2020 SOT economic model for the DMR BDO process indicates that the production and use of biomass degrading enzymes represents ~10% of the MFSP of BDO. We are thus working to enhance the performance of the dominant cellulase enzyme, Cel7A. In Fy2018-19, we selected 100 promising genes from the "Cel7A wheel of life" and cloned them into T. reesei using a constitutive promotor. This natural diversity screening resulted in the discovery of several enzymes exhibiting improved characteristics relative to the industry standard Cel7A from T. reesei (Tr). Growth of the transformed host on glucose insured that the Cre1 induced cellulase expression cascade was suppressed, thus enabling purification of the target gene product. The first top performing enzyme found was from P. funiculosum (Pf). Other top performing enzymes were identified from T. aculeatus, T. terrestris, and A. oryzae. Computational modeling predicted the structural subsites responsible for the improvements, which were cloned into the sequence of PfCel7A. The recombinant enzymes were expressed in T. reesei, purified, and tested. Testing was not possible with SOT relevant substrates, so the best-case substrate was used; solids from the DMR process subjected to a novel dilute alkaline wash to remove the "lignin shield." Two chimeric Cel7A enzymes show improved performance (1.2 to 1.35x) relative to PfCel7A, which in turn showed considerable improvement (1.6x) relative to T. reesei Cel7A. These new enzymes have been provided to our industrial partner for evaluation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Sampling probe

A system for sampling a surface includes a sampling probe including a housing with a probe end having a sampling fluid opening, a sampling fluid supply conduit and a sampling fluid exhaust conduit. The sampling fluid supply conduit supplies sampling fluid to the sampling fluid opening. The sampling fluid exhaust conduit includes a wall, a sampling fluid exhaust conduit inlet opening for removing sampling fluid from the sampling fluid opening, and a sampling fluid exhaust conduit outlet opening for removing fluid from the sampling fluid exhaust conduit. A sampling fluid analytic conduit is also provided in the sampling probe and has a sampling fluid analytic conduit inlet opening spaced upstream from the sampling fluid exhaust conduit outlet opening, downstream from the sampling fluid exhaust conduit inlet opening, and from the wall of the sampling fluid exhaust conduit. A wash conduit can also be provided. Methods for sampling are also disclosed.

Van Berkel, Gary↗

Electrochemical Mitigation of Corrosion in Molten Chloride Salts During CSP Plant Operation

We are designing an electrochemical flow-cell for removal of corrosive impurities from molten chloride salt Gen3 Concentrating Solar Power (CSP) plants during plant operation. Corrosive impurities will inevitably form in molten chloride salts upon exposure to air and moisture. We previously showed that even small amounts of these impurities, especially MgOHCl, will be detrimental in Gen3 CSP plants, necessitating prohibitively expensive containment alloys and frequent replacement of corroded components. Pre-purification of salt with Mg metal at temperatures above 650 degrees C is the current method for removing corrosive impurities from chloride salts before they are introduced to CSP systems. However, this is not a suitable method for impurity removal during plant operation. First, this method will produce MgO particulates which will damage plant components. Second, Mg metal is solid at the low temperature point (500 degrees C), so the purification will not proceed at a fast rate. At the high temperature point, Mg is soluble. In this case, fast purification may proceed, but dissolved metal is likely to precipitate out in cold-temperature point components, causing damage. In contrast, our electrochemically driven method allows fast Mg-based purification to proceed at the low temperature point, without formation of harmful particulates and without the risk of Mg metal precipitation. This novel approach is inspired by electrorefining techniques that are widely employed in industrial metallurgy for removal of impurities from metals. Impurities in the incoming molten salt will be reduced to inert MgO at the cathode, which can be removed by periodically washing the cell with acid. Simultaneously, Mg dissolution at the anode will ensure salt composition is maintained, with no net removal of Mg2+. We have validated this electrochemical approach at lab scale under static conditions with batch rectors. Furthermore, we have performed analytical modeling and technoeconomic analysis to produce a preliminary engineering design for the purification flow cell.

CSP↗

MSW Decontamination: Methods to Improve Biofuel Yields

MSW is usually contaminated with a variety of undesirable materials (food, chemicals, glass, metal) that can impact downstream applications such as conversion to biofuels. This presentation will showcase two decontamination methods using either a detergent wash or an organic solvent extraction to demonstrate up to 30% increase in biofuel precursor yields for plastic and paper MSW. The economics of the two decontamination methods will also be presented.

09 BIOMASS FUELS↗

Equivalent Breakeven Installed Cost: A Tradeoff-Informed Measure for Technoeconomic Analysis of Candidate Heliostat Improvements: Preprint

Technoeconomic analysis (TEA) is commonly used to determine economic viability of power-generating technologies, including concentrating solar power (CSP) and thermal (CST) production plants. Levelized cost of electricity (LCOE) and analogous measures provide an estimate of long-term costs for operating power plants over their designed lifetimes by accounting for revenues and costs in a time-discounted manner. While these measures are effective when assessing a technology's total lifecycle costs and productivity under various designs, TEA of candidate incremental technology improvements from the lens of LCOE can be limited when required investment and LCOE impacts are small. In this work, we propose a novel metric for TEA of a plant component technology that recasts relative changes in levelized system costs into component-specific capital cost budgets. This measure, which we refer to as the equivalent breakeven installed cost, is the maximum budget for the technology component that leads to improved levelized costs. We illustrate the usefulness of this metric using the example of candidate heliostat improvements for a CSP tower plant. Here, the results suggest that a reduction in mirror washing costs yield a total plant O&M cost of $37/kWe-yr, which is a breakeven proposition if the average reflectance is reduced from 0.90 to 0.85 as a result of the cost savings.

concentrating solar power↗