Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transport Aircraft”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Gear systems for advanced turboprops

A new generation of transport aircraft will be powered by efficient, advanced turboprop propulsion systems. Systems that develop 5,000 to 15,000 horsepower have been studied. Reduction gearing for these advanced propulsion systems is discussed. Allison Gas Turbine Division's experience with the 5,000 horsepower reduction gearing for the T56 engine is reviewed and the impact of that experience on advanced gear systems is considered. The reliability needs for component design and development are also considered. Allison's experience and their research serve as a basis on which to characterize future gear systems that emphasize low cost and high reliability.

Wagner, Douglas A.↗
NASA NTRS1987

Conceptual Final Paper on the Preliminary Design of an Oblique Flying Wing SST

A conceptual Oblique Flying Wing Supersonic Transport Aircraft (OFW, or surfplane because of its shape) was first proposed in 1957. It was reintroduced in 1987 in view of the emerging technology of artificial stabilization. This paper is based on the performance and economics study of an M2 B747-100B replacement aircraft. In order to make a fair comparison of this configuration with the B747, an end-sixties structural technology level is assumed. It is shown that a modern stability and control system can balance the aircraft and smooth out gusts, and that the OFW configuration equals or outperforms the B747 in speed, economy and comfort.

Van der Velden, Alexander J. M.↗
NASA NTRS1986

Computational wing design studies relating to natural laminar flow

Two research studies are described which directly relate to the application of natural laminar flow (NLF) technology to transonic transport-type wing planforms. Each involved using state-of-the-art computational methods to design three-dimensional wing contours which generate significant runs of favorable pressure gradients. The first study supported the Variable Sweep Transition Flight Experiment and involves design of a full-span glove which extends from the leading edge to the spoiler hinge line on the upper surface of an F-14 outer wing panel. A wing was designed computationally for a corporate transport aircraft in the second study. The resulting wing design generated favorable pressure gradients from the leading edge aft to the mid-chord on both upper and lower surfaces at the cruise design point. Detailed descriptions of the computational design approach are presented along with the various constraints imposed on each of the designs.

Waggoner, Edgar G.↗
NASA NTRS1988

A simple, analytic 3-dimensional downburst model based on boundary layer stagnation flow

A simple downburst model is developed for use in batch and real-time piloted simulation studies of guidance strategies for terminal area transport aircraft operations in wind shear conditions. The model represents an axisymmetric stagnation point flow, based on velocity profiles from the Terminal Area Simulation System (TASS) model developed by Proctor and satisfies the mass continuity equation in cylindrical coordinates. Altitude dependence, including boundary layer effects near the ground, closely matches real-world measurements, as do the increase, peak, and decay of outflow and downflow with increasing distance from the downburst center. Equations for horizontal and vertical winds were derived, and found to be infinitely differentiable, with no singular points existent in the flow field. In addition, a simple relationship exists among the ratio of maximum horizontal to vertical velocities, the downdraft radius, depth of outflow, and altitude of maximum outflow. In use, a microburst can be modeled by specifying four characteristic parameters, velocity components in the x, y and z directions, and the corresponding nine partial derivatives are obtained easily from the velocity equations.

Oseguera, Rosa M.↗
NASA NTRS1988

Techniques used in the F-14 variable-sweep transition flight experiment

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system; (2) two boundary-layer rakes; (3) surface pitot tubes; and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.

Anderson, Bianca Trujillo↗
NASA NTRS1986

Test of IR arrays on the Kuiper Airborne Observatory

NASA's Kuiper Airborne Observatory, which is a C-141 transport aircraft equipped with a 90-cm, all-reflective altazimuth telescope, has been engaged in the Kuiper Infrared Technology Experiment. Attention is presently given to the Experiment's flight series for state-of-the-art two-dimensional, 500-element arrays that use either blocked impurity band or bulk silicon devices. The switched FET readout scheme used on the three arrays flown thus far yields exceptionally low crosstalk. System sensitivities are found to be sufficient for the detection of both pointlike and extended sources; several of each type have been used in staring and scanning experiments.

Russell, R. W.↗
NASA NTRS1987

Results of NASA's Energy Efficient Engine Program

The major activity undertaken in the NASA Energy Efficient Engine Program has been completed. This paper reports on the progress made toward achieving the program goal of developing advanced technology to significantly reduce fuel consumption and operating costs of future subsonic transport-type propulsion systems. An additional goal was that the advanced concepts be compatible with future environmental regulations. Along with the results obtained, a brief overview of the design details of both the General Electric and Pratt and Whitney energy efficient engines and the overall program scope are presented. Overall, this program has been highly successful; the technology developed during its course is, and will continue to be, effectively employed in both current and future advance transport aircraft engine designs.

Ciepluch, Carl C.↗
NASA NTRS1988

Computation and comparison of the installation effects of compression pylons for a high wing transport

The three-dimensional transonic Euler method with boundary layer interaction is used to study the flow about a transport aircraft equipped with NASA-developed compression pylons. The results show that the present pylons perform well under the installed conditions, reducing the wing/pylon junction velocities and thus reducing the installed loft loss and drag. The predicted theoretical results are found to agree moderately well with experimental wind tunnel results.

Chandrasekaran, B.↗
NASA NTRS1988

Techniques used in the F-14 variable-sweep transition flight experiment

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary-layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system, (2) two boundary-layer rakes, (3) surface pitot tubes, and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.

Trujillo Anderson, Bianca↗
NASA NTRS1988

A panel method procedure for interference assessment in slotted-wall wind tunnels

This paper describes a method for three-dimensional wind tunnel interference assessment developed specifically for slotted-wall tunnels. The method is an adaptation to the assessment problem of a previously published high-order panel method procedure for simulating the flow in slotted-wall tunnel test sections. The method uses a mixed outer boundary condition, primarily a Neumann condition, with measured pressure constraints used to control only those boundary phenomena which can not be specified accurately a priori. Assessment results are illustrated from a calibration test with variations in wall geometry, and from tests of a generic subsonic transport aircraft configuration.

Kemp, William B., Jr.↗
NASA NTRS1988

Quasi-steady flight to quasi-steady flight transition for abort landing in a windshear - Trajectory optimization and guidance

Trajectory optimization and trajectory-guidance problems for abort-landing maneuvers in the presence of low-altitude wind shear are investigated by means of numerical simulations, with a focus on methods designed to achieve quasi-steady flight recovery (final values of the relative velocity, path inclination, and angle of attack equal to those for quasi-steady steepest climb). The derivation of the governing equations is outlined; the modeling techniques are explained; and results for a B-727 transport aircraft approaching a sea-level airfield at temperature 100 F are presented in extensive tables and graphs and characterized in detail. The techniques developed are shown to be effective in restoring the aircraft to stable quasi-steady flight.

Miele, A.↗
NASA NTRS1988

Some key considerations for high-speed civil transports

Factors affecting the development of a new generation of high-speed (supersonic/hypersonic) transports are reviewed. Market projections of growth on long-range routes indicate a potential need for faster transport aircraft by the turn of the century. A review of NASA-sponsored studies shows how both market forces and technology combine to define mission performance and vehicle design constraints. The vehicle worth and price projected for a given vehicle are shown to relate to an assumed technology level. Preliminary results from an initial set of vehicle concepts lead to the conclusion that currently projected technology will need to be enhanced with increased research to meet the first market window around the year 2000.

Morris, Charles E. K., Jr.↗
NASA NTRS1989

Study of a unified hardware and software fault-tolerant architecture

A unified architectural concept, called the Fault Tolerant Processor Attached Processor (FTP-AP), that can tolerate hardware as well as software faults is proposed for applications requiring ultrareliable computation capability. An emulation of the FTP-AP architecture, consisting of a breadboard Motorola 68010-based quadruply redundant Fault Tolerant Processor, four VAX 750s as attached processors, and four versions of a transport aircraft yaw damper control law, is used as a testbed in the AIRLAB to examine a number of critical issues. Solutions of several basic problems associated with N-Version software are proposed and implemented on the testbed. This includes a confidence voter to resolve coincident errors in N-Version software. A reliability model of N-Version software that is based upon the recent understanding of software failure mechanisms is also developed. The basic FTP-AP architectural concept appears suitable for hosting N-Version application software while at the same time tolerating hardware failures. Architectural enhancements for greater efficiency, software reliability modeling, and N-Version issues that merit further research are identified.

Lala, Jaynarayan↗
NASA NTRS1988

Life science experiments during parabolic flight: The McGill experience

Over the past twelve years, members of the Aerospace Medical Research Unit of McGill University have carried out a wide variety of tests and experiments in the weightless condition created by parabolic flight. This paper discusses the pros and cons of that environment for the life scientist, and uses examples from the McGill program of the types of activities which can be carried out in a transport aircraft such as the NASA KC-135.

Watt, D. G. D.↗
NASA NTRS1988

Waverider, volume 2

The results of a study concerning a High-Speed Civilian Transport Aircraft are discussed. An evaluation of the viability of four configurations is presented. One design considered in the Waverider configuration. The Waverider creates lift at high speeds through the use of shock waves. This shocklift when combined with conventionally created lift provides high lift/drag values at higher speeds than conventional configurations. The Waverider cruises at Mach 5.5, has a range of 6,500 nautical miles, and seats 250 passengers. The aircraft is operable from existing airfields and does not require any special traffic control considerations when operating in controlled airspace.

Nightingale, Pat↗
NASA NTRS1989

Crew procedures and workload of retrofit concepts for microwave landing system

Crew procedures and workload for Microwave Landing Systems (MLS) that could be retrofitted into existing transport aircraft were evaluated. Two MLS receiver concepts were developed. One is capable of capturing a runway centerline and the other is capable of capturing a segmented approach path. Crew procedures were identified and crew task analyses were performed using each concept. Crew workload comparisons were made between the MLS concepts and an ILS baseline using a task-timeline workload model. Workload indexes were obtained for each scenario. The results showed that workload was comparable to the ILS baseline for the MLS centerline capture concept, but significantly higher for the segmented path capture concept.

Summers, Leland G.↗
NASA NTRS1989

Intermetallic and ceramic matrix composites for 815 to 1370 C (1500 to 2500 F) gas turbine engine applications

Light weight and potential high temperature capability of intermetallic compounds, such as the aluminides, and structural ceramics, such as the carbides and nitrides, make these materials attractive for gas turbine engine applications. In terms of specific fuel consumption and specific thrust, revolutionary improvements over current technology are being sought by realizing the potential of these materials through their use as matrices combined with high strength, high temperature fibers. The U.S. along with other countries throughout the world have major research and development programs underway to characterize these composites materials; improve their reliability; identify and develop new processing techniques, new matrix compositions, and new fiber compositions; and to predict their life and failure mechanisms under engine operating conditions. The status is summarized of NASA's Advanced High Temperature Engine Materials Technology Program (HITEMP) and the potential benefits are described to be gained in 21st century transport aircraft by utilizing intermetallic and ceramic matrix composite materials.

Stephens, Joseph R.↗
NASA NTRS1989

Laminar flow - The past, present, and prospects

Flight research conducted on natural laminar flow (NLF) is discussed. Emphasis is on recent flight testing conducted by the National Aeronautics and Space Administration. To place these flight experiences in perspective, important flight tests from the early days of natural laminar flow research are first reviewed to recall the lessons learned at that time. Then, based on more recent flight experiences and analyses with state-of-the-art boundary layer stability theory, speculation is made on the possibility of extensive NLF on swept wing transport aircraft.

Wagner, R. D.↗