Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Target”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Experiment and simulation of the compositional evolution of Ti-B thin films deposited by sputtering of a compound target

The evolution of the coating stoichiometry with pressure, target-substrate distance, and angle was analyzed for dc sputtering of Ti{sub x}B (x=0.5, 1, 1.6) compound targets by elastic recoil detection analysis. For an investigation of the underlying fundamental processes primarily Ar was used as sputter gas. Additionally, the effect of a reactive gas (N{sub 2}) as well as bias voltage (floating up to -200 V) was briefly cross-checked. For deposition along the target normal (90 deg.) a pronounced Ti-deficiency of up to 20% is detected. Increasing the pressure or distance from 0.5 to 2 Pa and from 5 to 20 cm, respectively, leads to an almost equivalent linear increase in Ti/B ratio surpassing even the target composition. Off-axis depositions at lower angles (30 deg. and 60 deg.) on the other hand result in a higher Ti/B ratio. This is consistent with results obtained from Monte Carlo simulations combining the respective emission characteristics from the sputter process as well as the gas-phase transport. Hence, the pressure, distance, and sample position induced changes in chemical film composition can be understood by considering gas scattering and the angular distribution of the sputtered flux. The theoretically determined transition from a directional flux to thermal diffusion was experimentally verified by mass-energy analysis of the film-forming atoms.

36 MATERIALS SCIENCE↗

Simulations of electron transport and ignition for direct-drive fast-ignition targets

The performance of high-gain, fast-ignition fusion targets is investigated using one-dimensional hydrodynamic simulations of implosion and two-dimensional (2D) hybrid fluid-particle simulations of hot-electron transport, ignition, and burn. The 2D/3D hybrid-particle-in-cell code LSP[D. R. Welch et al., Nucl. Instrum. Methods Phys. Res. A 464, 134 (2001)] and the 2D fluid code DRACO[P. B. Radha et al., Phys. Plasmas 12, 056307 (2005)] are integrated to simulate the hot-electron transport and heating for direct-drive fast-ignition targets. LSP simulates the transport of hot electrons from the place where they are generated to the dense fuel core where their energy is absorbed. DRACO includes the physics required to simulate compression, ignition, and burn of fast-ignition targets. The self-generated resistive magnetic field is found to collimate the hot-electron beam, increase the coupling efficiency of hot electrons with the target, and reduce the minimum energy required for ignition. Resistive filamentation of the hot-electron beam is also observed. The minimum energy required for ignition is found for hot electrons with realistic angular spread and Maxwellian energy-distribution function.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cryogneic-Target Performance and Implosion Physics Studies on OMEGA

Recent progress in direct-drive cryogenic implosions on the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reviewed. Ignition-relevant areal densities of ~200 mg/cm^2 in cryogenic D2 implosions with peak laser-drive intensities of ~5 x 10^14 W/cm^2 were previously reported [T. C. Sangster et al., Phys. Rev. Lett. 100, 185006 (2008)]. The laser intensity is increased to ~10^15 W/cm^2 to demonstrate ignition-relevant implosion velocities of 3–4 x 10^7 cm/ s, providing an understanding of the relevant target physics. Planar-target acceleration experiments show the importance of the nonlocal electron-thermal-transport effects for modeling the laser drive. Nonlocal and hot-electron preheat is observed to stabilize the Rayleigh–Taylor growth at a peak drive intensity of ~10^15 W/cm^2. The shell preheat caused by hot electrons generated by two-plasmon-decay instability was reduced by using Si-doped ablators. The measured compressibility of planar plastic targets driven with high-compression shaped pulses agrees well with one-dimensional simulations at these intensities. Shock mistiming has contributed to compression degradation of recent cryogenic implosions driven with continuous pulses. Multiple-picket (shock-wave) target designs make it possible for a more robust tuning of the shock-wave arrival times. Cryogenic implosions driven with double-picket pulses demonstrate somewhat improved compression performance at a peak drive intensity of ~10^15 W/cm^2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ULTRASONIC AND RADIOGRAPHIC IMAGING OF NIOBIUM TARGET CAPSULES FOR RADIOISOTOPE PRODUCTION

In the case of proton-irradiated radioisotope production, niobium target capsules containing gallium are exposed to intense radiation, thermally induced stress, for extended periods. The structural integrity of the target capsules is of crucial importance for containing the accelerator-produced radioisotopes and target material. The capsule window should be as thin and transparent to the proton beam as possible, and preferably should not become significantly activated under proton irradiation. In addition, the material for the capsule needs to be as defect-free as possible. Niobium encapsulated gallium targets have a history of unpredictable failure under intense irradiation with 100 MeV protons. This study illustrates the utility of non-destructive testing in order to detect defects that may result in mechanical failure of the capsules during irradiation. Prior to this work, it was not known if the gallium initially wets the niobium capsule that encapsulates it, and if it does, it is not known to what degree. However, the imaging techniques used in this work show that local areas of wetting do occur. We used ultrasonic images from various lots of niobium capsule material to assess the integrity of the capsules. Digital radiography is also used to detect any voids in the gallium that will tend to cause local heating in the capsules.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Efficient laser-produced plasma extreme ultraviolet sources using grooved Sn targets

An efficient extreme ultraviolet (EUV) generation method has been developed with the use of a CO{sub 2} laser-produced plasma from a grooved target. A approx5% conversion efficiency from laser to 13.5 nm photons was obtained with the use of grooves in a tin target or by repeated laser pulse shots at the same target position. Modeling studies proved that the groove target controls the hydrodynamic expansion of the plasma leading to confinement which prevents the plasma escaping from the EUV production zone.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion-enhanced oxidation of aluminum as a fundamental surface process during target poisoning in reactive magnetron sputtering

Plasma deposition of aluminum oxide by reactive magnetron sputtering (RMS) using an aluminum target and argon and oxygen as working gases is an important technological process. The undesired oxidation of the target itself, however, causes the so-called target poisoning, which leads to strong hysteresis effects during RMS operation. The oxidation occurs by chemisorption of oxygen atoms and molecules with a simultaneous ion bombardment being present. This heterogenous surface reaction is studied in a quantified particle beam experiment employing beams of oxygen molecules and argon ions impinging onto an aluminum-coated quartz microbalance. The oxidation and/or sputtering rates are measured with this microbalance and the resulting oxide layers are analyzed by x-ray photoelectron spectroscopy. The sticking coefficient of oxygen molecules is determined to 0.015 in the zero coverage limit. The sputtering yields of pure aluminum by argon ions are determined to 0.4, 0.62, and 0.8 at 200, 300, and 400 eV. The variation in the effective sticking coefficient and sputtering yield during the combined impact of argon ions and oxygen molecules is modeled with a set of rate equations. A good agreement is achieved if one postulates an ion-induced surface activation process, which facilitates oxygen chemisorption. This process may be identified with knock-on implantation of surface-bonded oxygen, with an electric-field-driven in-diffusion of oxygen or with an ion-enhanced surface activation process. Based on these fundamental processes, a robust set of balance equations is proposed to describe target poisoning effects in RMS.

36 MATERIALS SCIENCE↗

Dominant front-side acceleration of energetic proton beams from plastic targets irradiated by an ultraintense laser pulse

An experimental observation has been made by using aluminum-coated Mylar foils, which strongly supports that in the case of plastic target, the energetic part of the proton beam originates from the front-side of the target. When a 30 fs laser pulse with an intensity of 1.6x10{sup 19} W/cm{sup 2} was irradiated on the 12.5-{mu}m-thick Mylar side of the aluminum-coated Mylar foil, the maximum proton energy was reduced by a factor 5.5 as compared to that of 3.3 MeV observed from the single layer of the Mylar foil. With the help of a two-dimensional particle-in-cell simulation, these observations can be interpreted that in the case of plastic target, the energetic proton beam originates from the front-side of the target. In the case of an aluminum-coated 6-{mu}m-thick Mylar foil, more energetic proton beams of 4.7 MeV were also observed when the laser pulse was irradiated on the aluminum side as compared to those of 3.4 MeV from the single Mylar foil.

43 PARTICLE ACCELERATORS↗

High quality ion acceleration from a double-layer target dominated by the radiation pressure of a transversely Gaussian laser pulse

The ion acceleration from a double-layer target irradiated by a transversely Gaussian laser pulse is investigated by theoretical analysis and particle-in-cell simulations. The main idea of the double-layer target is to match the transverse areal mass density of the target with the laser intensity profile by single ion specie with two densities or by two ion species. Two-dimensional particle-in-cell simulations show that the target deformation and the transverse instability are efficiently suppressed in the double-layer scheme, ions within the laser spot are uniformly accelerated and are well collimated in the forward direction, GeV/u monoenergetic ion beams with very low divergency are observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High Intensity Laser Proton Acceleration with Underdense Targets

Laser driven sources of high energy ions commonly use thin solid foils. However, recently experiments have shown that a gaseous target can produce proton beams with characteristics comparable to those obtained with solid targets. In underdense laser proton acceleration, volume effects dominate the acceleration, while in target normal sheath acceleration, the electric field value at the rear target side is directly related to the electron surface density. Using Particle-In-Cell simulations, we have studied in detail proton acceleration with high intensity laser pulses interacting with underdense plasmas. Underdense laser ion acceleration strongly depends on the length of the plasma, the laser pulse duration and intensity. A two-step acceleration process has been observed: first, ions are accelerated in volume by electric fields generated by hot electrons, second, the ion energy is boosted in a strong electrostatic shock propagating along the descending density profile.

43 PARTICLE ACCELERATORS↗

Micro focusing of fast electrons with opened cone targets

Using opened reentrant cone silicon targets, we have demonstrated the effect of micro focusing of fast electrons generated in intense laser-plasma interactions. When an intense femtosecond laser pulse is focused tightly onto one of the side walls of the cone, fast electron beam emitted along the side wall is observed. When a line focus spot, which is long enough to irradiate both of the side walls of the cone simultaneously, is used, two electron beams emitted along each side wall, respectively, are observed. The two beams should cross each other near the open tip of the cone, resulting in micro focusing. We use a two-dimensional Particle-In-Cell code to simulate the electron emission both in opened and closed cone targets. The simulation results of the opened cone targets are in agreement with the experimental observation while the results of the closed cone targets do not show the micro focusing effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Note: Development of target changeable palm-top pyroelectric x-ray tube

A target changeable palm-top size x-ray tube was realized using pyroelectric crystal and detachable vacuum flanges. The target metals can be exchanged easily by attaching them on the brass stage with carbon tape. When silver and titanium palates (area: 10 mm{sup 2}) were used as targets, silver L{alpha} and titanium K lines were clearly observed by bombarding electrons on the targets for 90 s. The intensities were the same or higher than those of previously reported pyroelectric x-ray tubes. Chromium, iron, nickel, copper, and zinc K lines in the x-ray tube (stainless steel and brass) disappeared by replacing the brass stage and the stainless steel vacuum flange with a carbon stage and a glass tube, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design of a deuterium and tritium-ablator shock ignition target for the National Ignition Facility

Shock ignition presents a viable path to ignition and high gain on the National Ignition Facility (NIF). In this paper, we describe the development of the 1D design of 0.5 MJ class, all-deuterium and tritium (fuel and ablator) shock ignition target that should be reasonably robust to Rayleigh-Taylor fluid instabilities, mistiming, and hot electron preheat. The target assumes 'day one' NIF hardware and produces a yield of 31 MJ with reasonable allowances for laser backscatter, absorption efficiency, and polar drive power variation. The energetics of polar drive laser absorption require a beam configuration with half of the NIF quads dedicated to launching the ignitor shock, while the remaining quads drive the target compression. Hydrodynamic scaling of the target suggests that gains of 75 and yields 70 MJ may be possible.

36 MATERIALS SCIENCE↗

Producing radiometals in liquid targets: Proof of feasibility with {sup 94m}Tc

{sup 94m}Tc was produced in a liquid target loaded with a molybdenum-salt solution. This novel technique allows for the irradiation of metals dissolved in a liquid solution, normally only available in metal powder or foil form. By using this approach, the existing liquid targets and transfer infrastructure of many PET cyclotrons can be used to produce radiometals, avoiding the need, expense and challenges of operating solid targets. Such an approach allows for rapid testing of new isotopes for proof of feasibility studies. Different concentrations of Mo solution and their effect on the target performance were tested. Sufficient quantities to allow for preclinical studies were produced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reduction of the fast electron angular dispersion by means of varying-resistivity structured targets

We present novel structured targets capable of collimating laser-generated fast electrons through dense plasmas. The proposed targets are made of narrow high- and low-Z filaments leading to a transversely modulated electrical resistivity profile. When featuring a spatially decreasing density, these targets permit both to guide the fast electrons and reduce their angular dispersion. The principle of our target design is explained by a theoretical model. Two-dimensional particle-in-cell simulations are performed to demonstrate its efficiency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quasimonoenergetic proton bunches generation from doped foil targets irradiated by intense lasers

We propose a scheme to generate 10 MeV-level quasimonoenergetic proton bunches using proton-doped heavy-ion targets irradiated by intense lasers via target normal sheath acceleration. The heavy substrate ions provide a long-life quasi-stable sheath field to accelerate the doped protons at the target rear and consequently a quasimonoenergetic proton bunch is produced. The scheme is demonstrated by two-dimensional particle-in-cell simulations. An exemplificative simulation with parameters of targets made by ion-implant technique, a kind of modern doping process, gives a quasimonoenergetic bunch with peak energy {approx}13MeV, energy spread {approx}24%, and {approx}nC charge at the focused laser intensity 10{sup 20}W/cm{sup 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laser-driven 1 GeV carbon ions from preheated diamond targets in the break-out afterburner regime

Experimental data are presented for laser-driven carbon C{sup 6+} ion-acceleration, verifying 2D-PIC studies for multi-species targets in the Break-Out Afterburner regime. With Trident's ultra-high contrast at relativistic intensities of 5 × 10{sup 20} W/cm{sup 2} and nm-scale diamond targets, acceleration of carbon ions has been optimized by using target laser-preheating for removal of surface proton contaminants. Using a high-resolution wide angle spectrometer, carbon C{sup 6+} ion energies exceeding 1 GeV or 83 MeV/amu have been measured, which is a 40% increase in maximum ion energy over uncleaned targets. These results are consistent with kinetic plasma modeling and analytic theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-intensity laser-driven proton acceleration enhancement from hydrogen containing ultrathin targets

Laser driven proton acceleration experiments from micron and submicron thick targets using high intensity (2 × 10{sup 21} W/cm{sup 2}), high contrast (10{sup −15}) laser pulses show an enhancement of maximum energy when hydrogen containing targets were used instead of non-hydrogen containing. In our experiments, using thin (<1μm) plastic foil targets resulted in maximum proton energies that were consistently 20%–100% higher than when equivalent thickness inorganic targets, including Si{sub 3}N{sub 4} and Al, were used. Proton energies up to 20 MeV were measured with a flux of 10{sup 7} protons/MeV/sr.

36 MATERIALS SCIENCE↗

Study on the effect of target on plasma parameters of magnetron sputtering discharge plasma

In this study, the effect of magnetron target on different plasma parameters of Argon/Hydrogen (Ar - H{sub 2}) direct current (DC) magnetron discharge is examined. Here, Copper (Cu) and Chromium (Cr) are used as magnetron targets. The value of plasma parameters such as electron temperature (kT{sub e}), electron density (N{sub e}), ion density (N{sub i}), degree of ionization of Ar, and degree of dissociation of H{sub 2} for both the target are studied as a function of input power and hydrogen content in the discharge. The plasma parameters are determined by using Langmuir probe and Optical emission spectroscopy. On the basis of the different reactions in the gas phase, the variation of plasma parameters and sputtering rate are explained. The obtained results show that electron and ion density decline with gradual addition of Hydrogen in the discharge and increase with rising input power. It brings significant changes on the degree of ionization of Ar and dissociation of H{sub 2}. The enhanced value of electron density (N{sub e}), ion density (N{sub i}), degree of Ionization of Ar, and degree of dissociation of H{sub 2} for Cr compared to Cu target is explained on the basis of it's higher Ion Induced Secondary Electron Emission Coefficient (ISEE) value.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗