SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report presents the results of wind tunnel tests to determine the effectiveness of various methods of reducing the high control forces of unbalanced upper-surface ailerons and of unbalanced split flaps.
The cooling of a single-row radial air-cooled engine using several cowling arrangements has been studied in the NACA 20-foot wind tunnel. The results show the effect of the propeller and several cowling arrangements on cooling for various values of the indicated horsepower in the climb condition. A table giving comparative performance of the various cowling arrangements is presented. The dependence of temperature on indicated horsepower and pressure drop across the baffles is shown by charts. Other charts show the limiting indicated horsepower against the pressure drop across the engine and the heat dissipated at various values of the indicated horsepower.
An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine induced aerodynamic effects from jet reaction controls of an advanced air-to-air missile concept. The 75-percent scale model featured independently controlled reaction jets located near the nose and tail of the model. Aerodynamic control was provided by four fins located near the tail of the model. This investigation was conducted at Mach numbers of 0.35 and 0.60, at angles of attack up to 75 deg and at nozzle pressure ratios up to 90. Jet-reaction thrust forces were not measured by the force balance but jet-induced forces were. In addition, a multiblock three-dimensional Navier-Stokes method was used to calculate the flowfield of the missile at angles of attack up to 40 deg. Results indicate that large interference effects on pitching moment were induced from operating the nose jets with the the off. Excellent correlation between experimental and computational pressure distributions and pitching moment were obtained a a Mach number of 0.35 and at angles of attack up to 40 deg.
An equivalent-plate structural deformation technique was coupled with a steady-state unstructured-grid three-dimensional Euler flow solver and a two-dimensional strip interactive boundary-layer technique. The objective of the research was to assess the extent to which a simple accounting for static model deformations could improve correlations with measured wing pressure distributions and lift coefficients at transonic speeds. Results were computed and compared to test data for a wing-fuselage model of a generic low-wing transonic transport at a transonic cruise condition over a range of Reynolds numbers and dynamic pressures. The deformations significantly improved correlations with measured wing pressure distributions and lift coefficients. This method provided a means of quantifying the role of dynamic pressure in wind-tunnel studies of Reynolds number effects for transonic transport models.
The use of multi-dimensional finite volume numerical techniques with finite thickness models for calculating aeroheating rates from measured global surface temperatures on hypersonic wind tunnel models was investigated. Both direct and inverse finite volume techniques were investigated and compared with the one-dimensional semi -infinite technique. Global transient surface temperatures were measured using an infrared thermographic technique on a 0.333-scale model of the Hyper-X forebody in the Langley Research Center 20-Inch Mach 6 Air tunnel. In these tests the effectiveness of vortices generated via gas injection for initiating hypersonic transition on the Hyper-X forebody were investigated. An array of streamwise orientated heating striations were generated and visualized downstream of the gas injection sites. In regions without significant spatial temperature gradients, one-dimensional techniques provided accurate aeroheating rates. In regions with sharp temperature gradients due to the striation patterns two-dimensional heat transfer techniques were necessary to obtain accurate heating rates. The use of the one-dimensional technique resulted in differences of 20% in the calculated heating rates because it did not account for lateral heat conduction in the model.
A wind tunnel experiment was conducted in the NASA Langley Research Center (LaRC) 8-Foot Transonic Pressure Tunnel (TPT) to determine the effects of passive surface porosity on vortex flow interactions about a general research fighter configuration at subsonic and transonic speeds. Flow-through porosity was applied to a wing leading-edge extension (LEX) mounted to a 65 deg cropped delta wing model to promote large nose-down pitching moment increments at high angles of attack. Porosity decreased the vorticity shed from the LEX, which weakened the LEX vortex and altered the global interactions of the LEX and wing vortices at high angles of attack. Six-component forces and moments and wing upper surface static pressure distributions were obtained at free-stream Mach numbers of 0.50, 0.85, and 1.20, Reynolds number of 2.5(10(exp 6)) per foot, angles of attack up to 30 deg, and angles of sideslip to +/- 8 deg. The off-surface flow field was visualized in selected cross-planes using a laser vapor screen flow visualization technique. Test data were obtained with a centerline vertical tail and with alternate twin, wing-mounted vertical fins having 0 deg and 30 deg cant angles. In addition, the porosity of the LEX was compartmentalized to determine the sensitivity of the vortex-dominated aerodynamics to the location and level of porosity applied to the LEX.
An experimental investigation was performed in the NASA Langley 16-Foot Transonic Tunnel to determine the aerodynamic effects of external convolutions, placed on the boattail of a nonaxisymmetric nozzle for drag reduction. Boattail angles of 15 and 22 were tested with convolutions placed at a forward location upstream of the boattail curvature, at a mid location along the curvature and at a full location that spanned the entire boattail flap. Each of the baseline nozzle afterbodies (no convolutions) had a parabolic, converging contour with a parabolically decreasing corner radius. Data were obtained at several Mach numbers from static conditions to 1.2 for a range of nozzle pressure ratios and angles of attack. An oil paint flow visualization technique was used to qualitatively assess the effect of the convolutions. Results indicate that afterbody drag reduction by convoluted contouring is convolution location, Mach number, boattail angle, and NPR dependent. The forward convolution location was the most effective contouring geometry for drag reduction on the 22 afterbody, but was only effective for M < 0.95. At M = 0.8, drag was reduced 20 and 36 percent at NPRs of 5.4 and 7, respectively, but drag was increased 10 percent for M = 0.95 at NPR = 7. Convoluted contouring along the 15 boattail angle afterbody was not effective at reducing drag because the flow was minimally separated from the baseline afterbody, unlike the massive separation along the 22 boattail angle baseline afterbody.
The use of multi-dimensional finite volume heat conduction techniques for calculating aeroheating rates from measured global surface temperatures on hypersonic wind tunnel models was investigated. Both direct and inverse finite volume techniques were investigated and compared with the standard one-dimensional semi-infinite technique. Global transient surface temperatures were measured using an infrared thermographic technique on a 0.333-scale model of the Hyper-X forebody in the NASA Langley Research Center 20-Inch Mach 6 Air tunnel. In these tests the effectiveness of vortices generated via gas injection for initiating hypersonic transition on the Hyper-X forebody was investigated. An array of streamwise-orientated heating striations was generated and visualized downstream of the gas injection sites. In regions without significant spatial temperature gradients, one-dimensional techniques provided accurate aeroheating rates. In regions with sharp temperature gradients caused by striation patterns multi-dimensional heat transfer techniques were necessary to obtain more accurate heating rates. The use of the one-dimensional technique resulted in differences of 20% in the calculated heating rates compared to 2-D analysis because it did not account for lateral heat conduction in the model.
This paper presents the results of the Computational Fluid Dynamics (CFD) analyses to model two atmospheric-boundary-layer (ABL) profiles inside the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). The CFD models include tunnel walls and all additional hardware needed to simulate the ABL profiles. This hardware includes Irwin spires and floor-mounted roughness elements. The numerical simulations show that the application of higher-fidelity numerical methods is necessary to compute boundary-layer and turbulenceintensity profiles that match experimental data. The ABL profiles are computed both inside the numerical model of the TDT and in a classical free-air model. Both Unsteady Reynolds Averaged Navier-Stokes (URANS) with Spalart-Allmaras (SA) turbulence model and Modified Delayed Detached Eddy (MDDES) simulation methods are used. The results show that the MDDES-simulation results match the experimental data very well while URANS-SA does not. The results also show that the wind-tunnel walls have a significant effect on ABL prediction.
Blunt bodies have been magnetically suspended in a 6-inch octagonal test-section low-subsonic wind tunnel in a free-to oscillate configuration. Capsule oscillations of two entry vehicle geometries were measured from high speed video of repeated test runs. An analytical solution to the 1degree-of-freedom equations of motion was fit to the measured oscillation histories to solve for a pitch damping coefficient. A six degree-of-freedom simulation was used to predict the wind tunnel data and assess the effect of magnetic forces on capsule dynamics. The predicted effect was used in the data reduction methodology to improved the pitch damping measurement. Pitch damping measurements are compared with heritage forced oscillation data and are in good agreement. Preliminary uncertainties are included with recommendations for improved data reduction.
The growing interest in the noise of small unmanned aircraft systems (sUAS) in operation has motivated this study to characterize and predict broadband rotor noise sources. This paper analyzes the performance and acoustic data collected from two sets of wind tunnel experiments for hover and forward flight operating conditions. The first set of data is a result of testing a representative vehicle configuration of the Straight Up Imaging (SUI) Endurance quadcopter, while the second set of data represents an isolated rotor from the same vehicle. Following the analysis of the empirical data, a broadband noise prediction methodology is employed to compare with the experiments. This methodology uses NASA’s ROTONET and BARC tools to predict blade loading and self-noise at conditions matching the wind tunnel experiments. This methodology is effective at predicting the broadband noise at certain conditions. Furthermore, some predictions are repeated with the inflow conditions calculated by the rotorcraft analysis tool CAMRAD II, which shows improved prediction results for cases with nonuniform inflow. This work confirms some of the unique challenges associated with testing small rotor configurations, explores the limitations of this prediction methodology, and suggests improvements that can be made for future studies.
A wind tunnel investigation has been conducted over the Mach number range from about 0.6 to 1.2 to determine the effects of large tip fins on the flutter characteristics of a swept wing. The basic wing configuration had an aspect ratio of 0.95, leading-edge sweep of 40 deg 0, and trailing-edge sweep of 21 deg. Two of these configurations were modified with tip fins of 60 deg dihedral and had effective aspect ratios of 1.5 and 2.2. In general, the results indicate that the addition of tip fins reduces the flutter speed, with the larger fin having the greater effect. Comparison of the experimental flutter speeds at Mach numbers between 0.60 and 0.90 with calculated values obtained by using doublet-lattice unsteady aerodynamic theory was good. Analytical results where structural and aerodynamic effects of the tip fins were isolated indicated that the reduction in flutter speed produced by the addition of the fins was caused by both effects, with the structural effect being the more pronounced.
A wind tunnel model mount system is disclosed for effectively and accurately determining the effects of attack and airstream velocity on a model airfoil or aircraft. The model mount system includes a rigid model attached to a splitter plate which is supported away from the wind tunnel wall several of flexible rods. Conventional instrumentation is employed to effect model rotation through a turntable and to record model flutter data as a function of the angle of attack versus dynamic pressure.
Low speed wind tunnel tests of takeoff, landing, and cruise aerodynamic characteristics of space shuttle booster with exhaust effect simulation
The icing protection obtained from an internally air-heated propeller blade partitioned to confine the heated air forward of 25-percent chord was investigated in the NACA Cleveland icing research tunnel. A production-model hollow steel propeller was modified with an Internal radial partition at 25-percent chord and with shank and tip openings to admit and exhaust the heated air. Temperatures were measured on the blade surfaces and in the heated-air system during tunnel icing conditions. Heat-exchanger effectiveness and photographs of Ice formations on the blades were obtained. Surface temperature measurements indicated that confining the heated air forward of the 25-percent chord gave.a more economical distribution of the applied heat as compared with unpartitioned and 50-percent partitioned blades, by dissipating a greater percentage of the available heat at the leading edge. At a propeller speed of 850 rpm, a heating rate of 7000 Btu per hour per blade at a shank air temperature of 400 F provided adequate Icing protection at ambient-air temperatures of 23 F but not at temperatures as low as 15 F. With the heating rate used, a heat-exchanger effectiveness of 77 percent was obtained as compared to 56 percent for 50-percent partitioned and 47 percent for unpartitioned blades.
The minimum operating temperature which avoids real-gas effects, such as condensation, was determined for M sub infinity = 0.85 flow over a 0.137-meter NACA 0012-64 airfoil mounted in the Langley 1/3-meter transonic cryogenic tunnel. For temperatures within 5 K of reservoir saturation and total pressures from 1.2 to 4.5 atmospheres, the pressure distributions over the airfoil are not altered by real-gas effects. This ability to test at total temperatures below those which avoid saturation over the airfoil allows an increase in Reynolds number capability of at least 17 percent for a constant tunnel total pressure. Similarly, 17 percent less total pressure is required to obtain a given Reynolds number.
Although extensive ground testing, utilizing both the Captive Trajectory system (CTS) and grid method, generally precedes flight testing of new aircraft/weapon combinations, the flight test results often do not match the wind tunnel predictions. These discrepancies are generally attributed to model scale, wind tunnel test errors and Reynolds Number effects, and may have been the cause of several previous aircraft/weapon incidents. The paper describes the procedure used at the Naval Air Warfare Center, Aircraft Division, Warminster (NAWCADWAR) during the early phases of wind tunnel testing and analysis, as well as subsequent flight testing to validate the predicted trajectories. This approach is designed to improve the safety of the flight tests for the critical portions of the aircraft envelope.
A high-lift propeller system is a distributed electric propulsion technology which dedicates an array of wing-mounted tractor propellers to actively augment wing lift during takeoff and landing. This paper describes the results of a wind tunnel experiment dedicated to investigating the effects of high-lift propeller installation geometry on lift generation. Variables investigated include propeller height, offset, and inclination. Results show that propeller height is the most critical variable and that the height for maximum lift depends highly on the angle of attack and flap deflection. In addition, a relationship between optimal propeller height and the wing’s unblown lift coefficient is discovered.