SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Two objectives of the space shuttle, or reusable reentry vehicle, are economy and the speed with which it can be made operational. Its mission will be carried out in six stages: launching, separation of the fuel tank, separation of the booster, placing the payload in orbit, return to the atmosphere, and the actual landing. The major element, the orbiter, is described. Some aspects of European participation in the program are discussed.
Limitations in the acquisition of nonlinear aerodynamic coefficients from free-oscillation data by means of the Chapman-Kirk technique, SAM-D control test vehicle trajectory plannning and flight test analysis, and determination of aerodynamic drag from radar data are among the topics covered in papers concerned with atmospheric flight mechanics. Other areas covered include fixed and rotary-wing aircraft, ordnance and reentry vehicles, and analysis and measurement techniques. Individual items are announced in this issue.
A laboratory prototype flash evaporator that is being developed as a candidate for the space shuttle environmental control system expendable heat sink is described. The single evaporator configuration uses water as an evaporant to accommodate reentry and on-orbit peak heat loads, and Freon 22 for terrestrial flight phases below 120,000 feet altitude. The design features, fabrication techniques used for the prototype unit, redundancy considerations, and the fluid temperature control arrangement are reported in detail. The results of an extensive test program to determine the evaporator operational characteristics under a wide variety of conditions are presented.
The generation of technology for injectors, cooled thrust chambers, valves, and ignition systems is discussed. The thrusters are designed to meet a unique and stringent set of requirements, including: long life for 100 mission reuses, high performance, light weight, ability to provide long duration firings as well as small impulse bits, ability to operate over wide ranges of propellant inlet conditions and to withstand reentry heating. The program has included evaluation of thrusters designed for ambient temperature and cold gaseous propellants at the vehicle interface.
A computer program that simulates the performance of a space radiator is presented. The program basically consists of a rigorous analysis which analyzes a symmetrical fin panel and an approximate analysis that predicts system characteristics for cases of non-symmetrical operation. The rigorous analysis accounts for both transient and steady state performance including aerodynamic and radiant heating of the radiator system. The approximate analysis considers only steady state operation with no aerodynamic heating. A description of the radiator system and instructions to the user for program operation is included. The input required for the execution of all program options is described. Several examples of program output are contained in this section. Sample output includes the radiator performance during ascent, reentry and orbit.
A study of internal insulation materials and fabrication processes for space shuttle LH2 tanks is reported. Emphasis was placed on an insulation system capable of reentry and multiple reuse in the Shuttle environment. Results are given on the optimization and manufacturing process scale-up of a 3D fiberreinforced foam insulation, BX-251-3D, derived from the Saturn S-4B internal insulation. It is shown that BX-251-3D can be satisfactorily installed in large-scale tanks under conditions that will permit a significant cost saving over the existing S-4B technology.
Closed-form solutions for the motion of a rocket-powered vehicle during atmospheric ascent and closed-form solutions for unpowered atmospheric reentry are developed. These closed-form solutions are then used to develop a simplified guidance scheme and to develop a variation-of-parameters integration of more accurate equations of motion with the closed-form solutions as base solutions. The variation-of-parameters integration of the more accurate equations of motion also allows the transition partial derivative matrices associated with these equations to be easily developed. Then the partial derivative transition matrices are used to develop a guidance scheme based on the more accurate equations of motion instead of the less accurate closed-form solutions.
The space shuttle rescue capability is analyzed as a part of the advanced mission safety study. The subjects discussed are: (1) mission evaluation, (2) shuttle configurations and performance, (3) performance of shuttle-launched tug system, (4) multiple pass grazing reentry from lunar orbit, (5) ground launched ascent and rendezvous time, (6) cost estimates, and (7) parallel-burn space shuttle configuration.
A study was conducted to determine methodology for combining thermal structural loads and assessing the effects of the combined loads on the design of a thermal protection system and a hot structure of a high cross range delta wing space shuttle orbiter vehicle. The study presents guidelines for establishing a basis for predicting thermal and pressure environments and for determining limit and ultimate design loads on the vehicle during reentry. Limit trajectories were determined by using dispersions on a representative nominal mission and system parameters expected during the life of the vehicle. Nine chosen locations on the vehicle surface having TPS or hot structures were examined, and weight sensitivity analyses were performed for each location.
A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 15 command module with wind-tunnel signatures extrapolated to flight distances has been made for Mach numbers of 1.16 and 4.57. The flight pressure signatures were recorded by pressure sensors located onboard ships positioned near the ground track while the wind-tunnel signatures were measured during tests of a 0.016-scale model of the command module. The agreement between estimates based on wind-tunnel data and flight measurements was better at Mach 4.57 than at Mach 1.16.
Previously collected data on atmospheric pressure, density, temperature and winds between 25 and 200 km from sources including Meteorological Rocket Network data, ROBIN falling sphere data, grenade release and pitot tube data, meteor winds, chemical release winds, satellite data, and others were analyzed by a daily difference method and results on the distribution statistics, magnitude, and spatial structure of gravity wave and planetary wave atmospheric variations are presented. Time structure of the gravity wave variations were determined by the analysis of residuals from harmonic analysis of time series data. Planetary wave contributions in the 25-85 km range were discovered and found to have significant height and latitudinal variation. Long period planetary waves, and seasonal variations were also computed by harmonic analysis. Revised height variations of the gravity wave contributions in the 25 to 85 km height range were computed. An engineering method and design values for gravity wave magnitudes and wave lengths are given to be used for such tasks as evaluating the effects on the dynamical heating, stability and control of spacecraft such as the space shuttle vehicle in launch or reentry trajectories.
A theoretical and preliminary design study of a large flexible tunnel for use at the shuttle/payload interface is discussed. The theoretical study consisted of evaluating various design concepts and determining their adaptability to the tunnel requirements. The theoretical study culminated in the selection of one concept. The selected concept was documented with preliminary drawings of a full-scale ground test model. Supporting preliminary structural, thermal, micrometeoroid, material, and weight analyses were conducted. The specified tunnel requirements could be broadly grouped into two categories; environmental and performance. The environmental requirements were those ambient conditions and loads associated with ground, launch, space and reentry of the shuttle vehicle. Materials are presently available which will meet all these environmental requirements and can be designed into the structure to withstand the specified loads.
Data from the Charged Particle Experiments of the IMP-4 and 5 spacecraft were processed and analyzed from launch through reentry. Approximately 95 percent of all data transmitted was recovered, processed, and analyzed. The computer programming and operational procedures which were developed to perform the processing and analysis of the data are discussed. The scientific results obtained from the analysis of the data are summarized. A bibliography of documents based on these experiments is included.
The computer programs developed for computation of viscous shock layer flow distribution surrounding the nose of a shuttle orbiter during reentry are presented. The problem formulation and the numerical procedures used to solve the basic set of equations are described. The results of flow distribution properties at several trajectory points, ranging from the high altitude rarefied region to the low altitude boundary layer region are analyzed.
Computer programs for calculating the flow distribution in the nose region of a blunt body at arbitrary speed and altitude are discussed. The programs differ from each other in their ability to consider either thin shock or thick shock conditions and in the use of either ideal, equilibrium air, or nonequilibrium air chemistry. The application of the programs to analyzing the flow distribution around the nose of the shuttle orbiter during reentry is reported.
A correlation of sonic boom pressure signatures recorded during reentry of the Apollo 16 command module with wind-tunnel signatures extrapolated to flight distances was made for Mach numbers of 1.83 and 9.71. The flight pressure signatures were recorded by microphones located onboard ships positioned near the ground track, whereas the wind tunnel signatures were measured during a test of a 0.016-scale model of the command module. The agreement between estimates based on wind tunnel data and flight measurements was good at the tested Mach numbers.
A program is described that was conducted to develop an internal insulation system for potential application to the liquid hydrogen tanks of a reusable booster, where the tanks would be subjected to repeated high temperatures. The design of the internal insulation is based on a unique gas layer concept, in which capillary or surface tension effects are used to maintain a stable gas layer, within a cellular core structure, between the tank wall and the contained liquid hydrogen. Specific objectives were to select materials for insulation systems that would be compatible with wall temperatures of 350 F and 650 F during reentry into the earth's atmosphere, and to fabricate and test insulation systems under conditions simulating the operating environment. A materials test program was conducted to evaluate the properties of candidate materials at elevated temperatures and at the temperature of liquid hydrogen, and to determine the compatibility of the materials with a hydrogen atmosphere at the appropriate elevated temperature. The materials that were finally selected included Kapton polyimide films, silicone adhesives, fiber glass batting, and in the case of the 350 F system, Teflon film.
Three silicide coated columbium alloys and two cobalt alloys were subjected to identical simulated reentry profiling exposures in both static (controlled vacuum leak) and dynamic (hypersonic plasma shear) environments. Primary emphasis in the columbium alloy evaluation was on the Cb752 and C129Y alloys with a lesser amount on FS85. Commercial silicide coatings of the R512E and VH109 formulations were used. The coated specimens were intentionally defected to provide the types of coating flaws that are expected in service. Temperatures were profiled up to peak temperatures of either 2350 F or 2500 F for 15 minutes in each cycle.