Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Developing high performance RF heating scenarios on the WEST tokamak

High power experiments, up to 9.2 MW with LHCD and ICRH, have been carried out in the full tungsten tokamak WEST. Here, quasi non inductive discharges have been achieved allowing to extend the plasma duration to 53 s with stationary conditions in particular with respect to tungsten contamination. Transitions to H mode are observed, and H-modes lasting up to 4 s have been obtained. The increase in stored energy is weak since the power crossing the separatrix is close to the L–H threshold. Hot L mode plasmas (central temperature exceeding 3 keV) with a confinement time following the ITER L96 scaling law are routinely obtained. The weak aspect ratio dependence of this scaling law is confirmed. Tungsten accumulation is generally not an operational issue on WEST. Difficulty of burning through tungsten can prevent the discharge from accessing to a hot core plasma in the ramp-up phase, or can lead to rapid collapse of the central temperature when radiation is enhanced by a slight decrease of the temperature. Except a few pulses post-boronization, the plasma radiation is rather high (P rad /P tot ~ 50%) and is dominated by tungsten. This fraction does not vary as the RF power is ramped up and is quite similar in ICRH and/or LHCD heated plasmas. An estimate of the contribution of the RF antennas to the plasma contamination in tungsten is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Modeling Subsurface Performance of a Geothermal Reservoir Using Machine Learning

Geothermal power plants typically show decreasing heat and power production rates over time. Mitigation strategies include optimizing the management of existing wells—increasing or decreasing the fluid flow rates across the wells—and drilling new wells at appropriate locations. The latter is expensive, time-consuming, and subject to many engineering constraints, but the former is a viable mechanism for periodic adjustment of the available fluid allocations. In this study, we describe a new approach combining reservoir modeling and machine learning to produce models that enable such a strategy. Our computational approach allows us, first, to translate sets of potential flow rates for the active wells into reservoir-wide estimates of produced energy, and second, to find optimal flow allocations among the studied sets. In our computational experiments, we utilize collections of simulations for a specific reservoir (which capture subsurface characterization and realize history matching) along with machine learning models that predict temperature and pressure timeseries for production wells. We evaluate this approach using an “open-source” reservoir we have constructed that captures many of the characteristics of Brady Hot Springs, a commercially operational geothermal field in Nevada, USA. Selected results from a reservoir model of Brady Hot Springs itself are presented to show successful application to an existing system. In both cases, energy predictions prove to be highly accurate: all observed prediction errors do not exceed 3.68% for temperatures and 4.75% for pressures. In a cumulative energy estimation, we observe prediction errors that are less than 4.04%. A typical reservoir simulation for Brady Hot Springs completes in approximately 4 h, whereas our machine learning models yield accurate 20-year predictions for temperatures, pressures, and produced energy in 0.9 s. This paper aims to demonstrate how the models and techniques from our study can be applied to achieve rapid exploration of controlled parameters and optimization of other geothermal reservoirs.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

Developing high performance RF heating scenarios on the WEST tokamak

High power experiments, up to 9.2 MW with LHCD and ICRH, have been carried out in the full tungsten tokamak WEST. Quasi non inductive discharges have been achieved allowing to extend the plasma duration to 53s with stationary conditions in particular with respect to tungsten contamination. Transitions in H mode are obtained lasting up to 4s with weak energy increment at the power crossing the separatrix is close to the threshold. Hot L mode plasmas (Te(0)>3keV) with a confinement time following the ITER L96 scaling are routinely obtained. The weak aspect ratio dependence of this scaling law is confirmed. Tungsten accumulation is generally not an operational issue on WEST. Difficulty of burning through tungsten can prevent from accessing to a hot core plasma in the ramp-up phase or can lead to rapid collapse of the central temperature when radiation is enhanced by a slight decrease of the temperature. Apart few pulses post-boronization, the plasma radiation is rather high (Prad/Ptot~50%) and is dominated by tungsten. This fraction does not vary as the RF power is ramped up and is quite similar in ICRH and/or LHCD heated plasmas. An estimate of the contribution of the RF antennas to the plasma contamination in tungsten is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Giant energy storage and power density negative capacitance superlattices

Dielectric electrostatic capacitors, because of their ultrafast charge-discharge, are desirable for high-power energy storage applications. Along with ultrafast operation, on-chip integration can enable miniaturized energy storage devices for emerging autonomous microelectronics and microsystems. Moreover, state-of-the-art miniaturized electrochemical energy storage systems-microsupercapacitors and microbatteries-currently face safety, packaging, materials and microfabrication challenges preventing on-chip technological readiness, leaving an opportunity for electrostatic microcapacitors. Here, in this study, we report record-high electrostatic energy storage density (ESD) and power density, to our knowledge, in HfO 2 -ZrO 2 -based thin film microcapacitors integrated into silicon, through a three-pronged approach. First, to increase intrinsic energy storage, atomic-layer-deposited antiferroelectric HfO 2 -ZrO 2 films are engineered near a field-driven ferroelectric phase transition to exhibit amplified charge storage by the negative capacitance effect, which enhances volumetric ESD beyond the best-known back-end-of-the-line-compatible dielectrics (115 J cm -3 ). Second, to increase total energy storage, antiferroelectric superlattice engineering scales the energy storage performance beyond the conventional thickness limitations of HfO 2 -ZrO 2 -based (anti)ferroelectricity (100-nm regime). Third, to increase the storage per footprint, the superlattices are conformally integrated into three-dimensional capacitors, which boosts the areal ESD nine times and the areal power density 170 times that of the best-known electrostatic capacitors: 80 mJ cm -2 and 300 kW cm -2 , respectively. This simultaneous demonstration of ultrahigh energy density and power density overcomes the traditional capacity-speed trade-off across the electrostatic-electrochemical energy storage hierarchy. Furthermore, the integration of ultrahigh-density and ultrafast-charging thin films within a back-end-of-the-line-compatible process enables monolithic integration of on-chip microcapacitors, which can unlock substantial energy storage and power delivery performance for electronic microsystems.

25 ENERGY STORAGE↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells (Final Report)

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co2O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly 4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Validation of Computational Fluid Dynamics Simulations for Biological Performance Assessment in Hydropower units (Final Report)

The biological performance assessment (BioPA) toolset developed by Pacific Northwest National Laboratory (PNNL) estimates the relative biological performance of fish passage at a hydroelectric power turbine unit. The tool is based on the use of computational fluid dynamics (CFD) and fish biological response relationships. The recent release, BioPA-v3, is based on directly computed trajectory and collision of material Lagrangian particles using CFD simulation codes rather than the prior version that relies on Tecplot to compute streamtrace trajectories. Before modifying the toolset, a series of validation tests were performed at the various steps of modification in the toolset. Validation is a critical step of any numerical investigation that reflects the accuracy and reliability of the predicted results. It raises the confidence level of the user to use the modified version of the BioPA toolset. Several test cases were simulated and compared, where available, to observed data. The trajectory and collision of the small spherical and cylindrical particles in a water flume were compared to in-house experiments. The CFD predicted collision rate and flow field compared well with experimental observation for vane array and large cylinder as target bodies. Next, the CFD-predicted flow field and hydraulic performance of a laboratory-scale model of a Francis turbine was also successfully validated. Note that the trajectory of the particles is significantly affected by the flow field in such extreme conditions. In addition to the particle trajectories and flow field, the collision detection method employed in the CFD simulations was also successfully validated. The CFD predicted impact velocity, collision time, velocity, and trajectory of a sphere excellently matched with analytical value for a bouncing ball in the elastic collision. A similar approach was also tested and successfully validated for a collision of sphere with a 45° inclined plane. After successfully validating different cases, the BioPA toolset was modified to use direct output of the CFD prediction and the new version can be used in evaluating biological performance at hydroelectric turbines.

13 HYDRO ENERGY↗
DOE OSTI2026

Enhanced Component Performance Study: Turbine-Driven Pumps 1998-2024

This report presents an enhanced performance evaluation of turbine driven pumps (TDPs) at U.S. commercial nuclear power plants. The data used in this study are based on the operating experience failure reports from calendar year 1998 through 2024 as reported in the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS). The TDP failure modes considered for standby systems are fail to start (FTS), fail to run (FTR) for one hour of operation (FTR=1H), FTR after one hour of operation (FTR>1H), and for normally running systems FTS and FTR. An eight hour unreliability estimate is also calculated and trended. The component reliability estimates and the reliability data are trended for the most recent 10 year period while yearly estimates for reliability are provided for the entire study period. No increasing trends were identified for TDPs for the most recent 10 year period.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Enhanced Component Performance Study: Air Operated Valves 1998–2022

This report presents an enhanced performance evaluation of air operated valves (AOVs) at U.S. commercial nuclear power plants. The data used in this study are based on the operating experience failure reports from calendar year 1998 through 2022 as reported in the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS). The AOV failure modes considered are fail to open or close (FTOC), fail to operate or control (FTOP), and spurious operation (SO). The component reliability estimates and the reliability data are trended for the most recent 10 year period while yearly estimates for reliability are provided for the entire study period. The following increasing trends were identified for AOVs for the most recent 10 year period: • Low demand AOV frequency of FTOC demands (demands per reactor year) • High demand AOV frequency of FTOC demands. The following decreasing trends were identified for AOVs for the most recent 10 year period: • Low demand AOV FTOC failure probability • Low demand AOV FTOP failure rate • Low demand AOV frequency of FTOC events (failures per reactor year) • Low demand AOV frequency of FTOP events.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Techno-economic implications and cost of forecasting errors in solar PV power production using optimized deep learning models

Accurate solar Photovoltaic (PV) power forecasting is important for enhancing both the performance and economic feasibility of PV systems. This study evaluates several deep learning models, including Dense Neural Networks (DNN), Long Short-Term Memory (LSTM), Convolutional Neural Networks (CNN), and a hybrid LSTMCNN model, for predicting PV power production one day in advance. Prior to optimization, the models exhibited relatively high errors, with the best model (DNN) achieving a Root Mean Square Error (RMSE) of 31.13 kW and a coefficient of determination (R 2 ) of 62.15 %. After employing Bayesian optimization, the LSTM-CNN model demonstrated the best performance, with the RMSE reduced to 9.79 kW and R 2 improved to 97.62 %, showcasing significant enhancement in predictive accuracy. Here, the economic evaluation considered three cases: rewards for underestimation (0.08 USD/kWh), no rewards, and penalties for both over-and underestimation (120 % of the utility tariff). In the rewards scenario, the LSTM-CNN model reduced the Levelized Cost of Electricity (LCOE) by 4 %, while in the penalty scenario, a backup diesel generator would have increased the LCOE by 49 %. Additionally, the LSTM-CNN model minimized financial losses, achieving the lowest penalties and maximizing net cash flow compared to other models, demonstrating its overall technical and economic superiority.

Deep learning↗
DOE OSTI2021

Grid Voltage Control Analysis for Heavy-Duty Electric Vehicle Charging Stations: Preprint

This paper presents an analysis of voltage control strategies for heavy duty electric vehicle (EV) charging stations. The performance of three voltage control approaches including power factor control, preset volt-var curve control, and customized volt-var curve control, have been investigated and evaluated for three different sizes of charging stations, including single-port small charging station, three-port middle size charging station, and 6-port travel center. The charging stations have been placed on various locations of four different types of distribution systems, to obtain a comprehensive performance analysis of the three voltage control approaches under different scenarios. To quantitively compare the performance of the three voltage control approaches, a series of metrics have been designed to quantify the performance and contribute to the comprehensive analysis summary.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Energy management systems for forecasted demand error compensation using hybrid energy storage system in nanogrid

This paper proposes an energy management system (EMS) for nanogrids to balance the power supply and forecasted demand in consideration of forecasting errors arising from high instantaneous demand. The proposed EMS employs a power-balancing optimization process for forecasted demand and a reference power modulation strategy for forecasting errors. This power-balancing optimization utilizes nanogrid sources, such as photovoltaics, fuel cells, and batteries, to meet forecasted demand and a supercapacitor charging process to overcome issues with a low energy density. The proposed reference power modulation strategy is utilized to allocate power from a hybrid energy storage system consisting of a battery and supercapacitor in order to compensate for forecasting errors. In addition, this proposed strategy considers battery and supercapacitor constraints such as the power changing rate and total power limitations. Further, the power-balancing optimization process also operates at faster sampling rate than the reference power modulation process in order to improve the computational efficiency. The performance of the proposed EMS is evaluated using real data obtained from the Korea Electric Power Exchange.

25 ENERGY STORAGE↗
DOE OSTI2022

Simulation of 15% and 50% Thermal Power Dispatch to an Industrial Facility Using a Flexible Generic Full-Scope Pressurized Water Reactor Plant Simulator

Nuclear power plants in the United States are increasingly challenged to compete in wholesale electricity markets due to the low electricity costs and increasingly dynamic grid conditions from competing generation sources. An alternative market for nuclear power is industrial facilities that can use the thermal and/or electrical power generated by a nuclear power plant to offset the economic losses incurred by electricity market challenges. A generic pressurized water reactor (PWR) simulator was used to show the results of a basic design for a generic thermal power extraction system and tests were run using a set of procedures to show what happens when a nuclear power plant transitions from full electrical power dispatch to 15% and 50% thermal power dispatch. This type of operation leads to losses in turbine performance efficiency due to the deviation from the design operating point, but because the thermal power is also used by the industry load without conversion losses, the combined thermal efficiency of the PWR increases. For the 15% case, the thermal efficiency increased from 32% to 41.9%, while for the 50% case, the efficiency increased up to 60.1%. In addition, for 50% thermal power dispatch, the power dissipated by the condenser decreased from approximately 2000 to approximately 1300 MW (thermal), indicating a substantially diminished impact on the environment in terms of releasing heat into the cooling water reservoir.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Grid Voltage Control Analysis for Heavy-Duty Electric Vehicle Charging Stations

This paper presents an analysis of grid voltage control strategies for heavy-duty electric vehicle charging stations. The performance of three voltage control approaches—including power factor control, standardized volt-volt ampere reactive (VAR) curve control, and customized volt-VAR curve control—are investigated and evaluated for three different sizes of charging stations, including a single-port charging station, a midsized three-port charging station, and six-port travel center. The charging stations are placed on multiple locations of four different types of distribution systems to obtain a comprehensive performance analysis of the voltage control approaches under different scenarios. To quantitively compare the performance of the three voltage control approaches, a series of metrics are designed to quantify the performance and contribute to the comprehensive analysis.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

110 GHz, 110 mW hybrid silicon-lithium niobate Mach-Zehnder modulator

High bandwidth, low voltage electro-optic modulators with high optical power handling capability are important for improving the performance of analog optical communications and RF photonic links. Here we designed and fabricated a thin-film lithium niobate (LN) Mach-Zehnder modulator (MZM) which can handle high optical power of 110 mW, while having 3-dB bandwidth greater than 110 GHz at 1550 nm. The design does not require etching of thin-film LN, and uses hybrid optical modes formed by bonding LN to planarized silicon photonic waveguide circuits. A high optical power handling capability in the MZM was achieved by carefully tapering the underlying Si waveguide to reduce the impact of optically-generated carriers, while retaining a high modulation efficiency. The MZM has a $V_πL$ product of 3.1 V.cm and an on-chip optical insertion loss of 1.8 dB.

42 ENGINEERING↗
DOE OSTI2021

Scenario adaptive disruption prediction study for next generation burning-plasma tokamaks

Next generation High Performance (HP) tokamaks risk damage from unmitigated disruptions at high current and power. Achieving reliable disruption prediction for a device's HP operation based on its Low Performance (LP) data is a key to its success. In this letter, through explorative data analysis and dedicated numerical experiments on multiple existing tokamaks, we demonstrate how the operational regimes of tokamaks can affect the power of a trained disruption predictor. First, our results suggest data-driven disruption predictors trained on abundant LP discharges work poorly on the HP regime of the same tokamak, which is a consequence of the distinct distributions of the tightly correlated signals related to disruptions in these two regimes. Second, we find that matching operational parameters among tokamaks strongly improves cross-machine accuracy which implies our model learns from the underlying scalings of dimensionless physics parameters like q 95 , β p and confirms the importance of these parameters in disruption physics and cross machine domain matching from the data-driven perspective. Finally, our results show in the absence of HP data from the target devices, the best predictivity of the HP regime for the target machine can be achieved by combining LP data from the target with HP data from other machines. Furthermore, these results provide a possible disruption predictor development strategy for next generation tokamaks, such as ITER and SPARC, and highlight the importance of developing baseline scenario discharges of future tokamaks on existing machines to collect more relevant disruptive data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Performance Characterization of a Natural Gas–Air Rotating Detonation Engine

An experimental study of a rotating detonation engine (RDE) operating with natural gas and air at elevated chamber pressures and air preheat temperatures was conducted to quantify its performance at conditions representative of land-based power generation gas turbine engines. Here, the thrust produced by the combustor was measured to characterize its work output potential. High-frequency pressure transducers and broadband chemiluminescence measurements of the flame provided information about the wave structure and dynamics. Analysis of common performance metrics demonstrated the necessity of normalizing any RDE performance parameter by the driving system potential, typically the reactant manifold pressure. Application of a thermodynamic performance model to a generic RDE identified the area ratio between the RDE exhaust and injection throats as the primary parameter affecting delivered pressure gain. The model was further applied to draw comparison with experimental measurements of net pressure gain for identical flow conditions. Only one of the two tested injector configurations followed the predicted trends, suggesting that performance of the second was governed by physical processes other than the reactant thermodynamics. Although an absolute pressure gain was not demonstrated, it is promising that the natural gas–air RDE delivered up to 90% of the theoretical performance.

20 FOSSIL-FUELED POWER PLANTS↗