SEARCH · Engineering Papers

Results for “Plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Robust foil regenerator flow loss and heat transfer tests under oscillating flow condition

A regenerator works as an energy storage component in a Stirling engine. Thus, it is one of the most critical components that makes the Stirling engine highly efficient. Traditionally, the regenerators are made of wire media such as woven screens and random fibers. These wire regenerators experience considerably high flow losses through the regenerator due to the flow separation and the resulting vortices. The high flow losses associated with the flow separation and vortices result in a lower engine efficiency. This research is to test a new robust foil regenerator to investigate its feasibility for free-piston Stirling engine applications. The robust foil regenerator is configured with parallel flow channels and stiffening ribs. Comparing to complex flows patterns in woven screen and random fiber regenerators, the flows in the parallel plates are simple and the flow losses are considerably small, and the heat transfer coefficient is also relatively small. To test the regenerator experimentally, a regenerator test rig was manufactured. To verify the accuracy of the test rig, a woven screen regenerator was made and tested prior to the robust foil regenerator test. The friction factor correlation of the woven screen regenerator shows a good agreement with the published regenerator correlations. The robust foil regenerator tests were conducted under the oscillating flow condition with different Reynolds numbers. The flow losses were measured with dynamic pressure transducers and the friction coefficient was derived from measured pressure drop. The measured temperature difference over the regenerator was used to calculate the heat transfer coefficient and Nusselt number. The figure of merit with two methods of NPH/NTU ratio and j/f ratio was calculated to evaluate the suitability of the robust foil regenerator. The results show that the robust foil regenerator has considerably higher figure of merit and therefore, better performance than other types of regenerator.

42 ENGINEERING↗

DOE OSTI2023

Toward local core outlet temperature monitoring in gas-cooled nuclear reactors using distributed fiber-optic temperature sensors

Gas-cooled nuclear reactors operate at temperatures up to 950 °C with significant spatial variations in power generation and coolant flow through hundreds of parallel flow channels, resulting in complex mixing at the core outlet. The high temperatures and complex mixing can damage downstream components, challenge reactor calorimetry for power determination, and result in significant conservatism in calculated peak fuel temperatures, which ultimately limits the total power output. Directly measuring each gas stream individually is unrealistic using single point thermocouples, requiring more robust sensing techniques. Fiber-optic sensors are resilient to high temperatures (up to 1,000 °C) and radiation damage. Moreover, distributed measurements can be made along the length of one fiber, making them potential candidates for monitoring local core outlet temperatures to improve core calorimetry and identify hot channels. Here, to the authors’ knowledge, this manuscript is the first to report spatially distributed fiber optic temperature measurements to quantify mixing at the outlet of a relevant orifice plate under prototypic temperature and flow regimes to assess the feasibility of using fiber-optic sensors for distributed measurements of coolant temperature in gas-cooled reactors. A single optical fiber captured dynamic changes in local temperatures, whereas the mixed outlet temperature exhibited a muted response and could not identify which channels were responsible for the change in the mixed outlet temperature. The discussion focuses on potential challenges for deploying distributed optical fibers in gas-cooled reactors, including the effects of vibrations, radiation-induced signal attenuation and drift, and routing of the fiber while minimizing flow obstructions.

42 ENGINEERING↗

DOE OSTI2025

Impact of Different Thermal Gradients on the Dynamics of Cylindrical Lithium-ion Cells Subject to Accelerated Aging and on Module Performance

This study investigates the impacts of applying different thermal gradient patterns to cylindrical lithium-ion cells in a module on cell dynamics (temperatures, current flows, state of charge), module performance (evolution of resistance, capacity, and energy versus cycle number), and module lifetime. The thermal gradients were generated using cooling plates (CPs) with three different flow-field designs, namely, straight, perpendicular, and U-turn. The study uses computational fluid dynamics (CFD), the pseudo-two-dimensional (P2D) battery model, capacity loss and increased impedance due to the growth of a solid-electrolyte-interphase, and the electric current distribution from module terminals to cells that depends on the series-parallel electrical connections among the cells. The impact of the thermal gradient (resulting from the CP designs) on the variability in resistance, current, state of charge, and voltage among the cells was analyzed and linked to differences in the module's performance. Applying a thermal gradient to parallel-connected strings of series-connected cells led to variation in the current through each parallel string and an imbalance in the voltage of series-connected cells. Module performance is poorer when the thermal gradient causes a voltage imbalance than when it causes a current imbalance. Module performance becomes the worst when both current variation and voltage imbalance happen together. For instance, the module's lifetime (estimated as reaching 80% of its initial capacity) varied by 5% to 17.5%, depending on the magnitude and pattern of the imposed thermal gradient. As the relative orientation between thermal gradients and cells' electrical connectivity influences the module's performance, appropriate consideration should be given to the choice of the CP, especially if large thermal gradients are allowed.

Battery thermal management↗

DOE OSTI2022

Tin sensitization and silver activation on indium tin oxide surfaces

Adhesion of electrical contacts on electronic and optoelectronic devices is important for reliable device operation. Sn-sensitization is a widely used process that improves uniformity and adhesion of plated metals to glass and polymer surfaces. Electrically conductive substrates can significantly benefit from improved uniformity, adhesion, and contact resistance to metallic contact layers. In this study, we investigate the process of Sn-sensitization and Ag-activation on indium tin oxide (ITO) surfaces—a dominant transparent conducting oxide used in optoelectronic devices. Here, our results show that ITO films exposed to Sn-sensitization solutions with HCl concentrations below 10 mM effectively modify the surface termination through the process of Sn-sensitization (Sn-bonding at the surface hydroxide sites) without etching the ITO film. However, the subsequent Ag-activation on an ITO surface does not seem to follow the typical response on a glass substrate, suggesting that Ag-activation of an ITO surface is likely limited by the Ag ion size relative to the area density of surface hydroxide sensitization sites.

42 ENGINEERING↗

DOE OSTI2023

Mef2c regulates bone mass through Sost -dependent and -independent mechanisms

We report Mef2c is a transcription factor that mediates key cellular behaviors that promote endochondral ossification and bone formation. Previously, Mef2c has been shown to regulate Sost transcription via its osteocyte-specific enhancer, ECR5, and conditional deletions of Mef2 cfl/fl with either Col1-Cre or Dmp1-Cre produced generalized high bone mass (HBM) consistent with Van Buchem Disease phenotypes. However, Sost -/- ; Mef2 cfl/fl ; Dmp1-Cre mice produced a significantly higher bone mass phenotype that Sost-/- alone suggesting that Mef2c modulates bone mass through additional mechanisms, independent of Sost. To identify new Mef2c transcriptional targets important in bone metabolism, we profiled gene expression by single-cell RNA sequencing in subpopulations of cells isolated from Mef2 cfl/fl ; Dmp1-Cre and Mef2 cfl/fl ; Bglap-Cre femurs, both strains exhibiting similar high bone mass phenotypes. However, we found Mef2cfl/fl; Bglap-Cre to also display a growth plate defect characterized by an expansion of several osteoprogenitor subpopulations. Differential gene expression analysis identified a total of 96 up- and 2434 down- regulated genes in Mef2 cfl/fl ; Bglap-Cre and 176 up- and 1041 down- regulated genes in Mef2 cfl/fl ; Dmp1-Cre bone cell subpopulations compared to wildtype mice. Mef2c deletion affected the transcriptomes across several cell types including mesenchymal progenitors (MP), osteoprogenitors (OSP), osteoblast (OB), and osteocyte (OCY) subpopulations. Several energy metabolism genes such as Uqcrb, Ndufv2, Ndufs3, Ndufa13, Ndufb9, Ndufb5, Cox6a1, Cox5a, Atp5o, Atp5g2, Atp5b, Atp5 were significantly down regulated in Mef2c-deficient OBs and OCYs, in both strains. Binding motif analysis of promoter regions of differentially expressed genes identified Mef2c binding in Bone Sialoprotein (BSP/Ibsp), a gene known to cause increased trabecular BV/TV in the femurs of Ibsp -/- mice. Immunohistochemical analysis confirmed the absence of Ibsp protein in OBs and OCYs. These findings suggests that the HBM in Sost -/- ; Mef2 cfl/fl ; Dmp1-Cre is caused by a multitude of transcriptional changes in genes that regulate bone formation, two of which are Sost and Ibsp.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Unraveling compacted graphite evolution during solidification of cast iron using in-situ synchrotron X-ray tomography

In spite of many years of research, the physical phenomena leading to the evolution of compacted graphite (CG) during solidification is still not fully understood. In particular, it is unknown how highly branched CG aggregates form and evolve in the semi-solid, and how local microstructural variations at micrometer length scale affect this growth process. We present here the first time-resolved synchrotron tomography combined with a bespoke high-temperature environmental cell that allows direct observation of the evolution of CG and relates this dynamic process to the local surrounding microstructures in a cast iron sample during repeated melting and solidification. Distinct processes are identified for the formation of CG involving the nucleation, growth, development of branches and interconnection of graphite particles, ultimately evolving into highly branched graphite aggregates with large sizes and low sphericities. CG is found to nucleate with a spheroidal or a plate-like shape, developing branches induced by high carbon concentration, e.g. thin melt channels. Additionally, CG grows much faster than spheroidal graphite during subsequent cooling in solid state. The direct visualization of the dynamic solidification process provides unprecedented new insights into formation mechanisms of CG and correlating factors such as local microstructural variations, and guides the development of CG iron solidification models.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗

DOE OSTI2023

Microstructure and defect engineering of graphite anodes by pulsed laser annealing for enhanced performance of lithium-ion batteries

We report nanosecond pulsed laser annealing significantly improves cyclability and current carrying capacity of lithium-ion batteries (LIBs). This improvement is achieved by engineering of microstructure and defect contents present in graphite in a controlled way by using pulsed laser annealing (PLA) to increase the number density of Li + ion trapping sites. The PLA treatment causes the following changes: (1) creates surface steps and grooves between the grains to improve Li + ion charging and intercalation rates; (2) removes inactive polyvinylidene difluoride (PVDF) binder from the top of graphite grains and between the grains which otherwise tends to block the Li + migration; and (3) produces carbon vacancies in (0001) planes which can provide Li + charging sites. From X-ray diffraction data, we find upshift in diffraction peak or reduction in planar spacing, from which vacancy concentration was estimated to be about 1.0%, which is higher than the thermodynamic equilibrium concentration of vacancies. The laser treatment creates single and multiple C vacancies which provide sites for Li + ions, and it also produces steps and grooves for Li + ions to enter the intercalating sites. It is envisaged that the formation of these sites enhances Li+ ion absorption during charge and discharge cycles. The current capacity increases from an average 360 mAh/g to 430 mAh/g, and C–V shows significant reduction in SEI layer formation after the laser treatment. If the vacancy concentration is too high and charge-discharge cycles are long, then trapping of electrons by Li + may occur, which can lead to Li 0 formation and Li plating causing reduction in current capacity.

25 ENERGY STORAGE↗

DOE OSTI2023

Silver-carbon interlayers in anode-free solid-state lithium metal batteries: Current development, interfacial issues, and instability challenges

As an interlayer between the anode and the electrolyte of the all-solid-state lithium metal batteries (ASSLMBs), the silver-carbon (Ag-C) nanocomposite has been reported to significantly increase the energy density and cycle rate of solid-state lithium metal batteries. Ag-C interlayers serve as mixed ionic-electronic conductor that conducts both Li+ ions and electrons and lithium storage capacity. Unfortunately, it was unclear how the Ag-C interlayer regulated lithium plating and stripping. Moreover, the structural and chemical instabilities between the interlayer and the electrolyte, within the interlayer, or beneath the interlayer on lithium substrate are likely to cause cell failure. In this review, we discuss interfacial issues and summarize recent progress in solution strategies for ASSLMBs, with a specific focus on the use of a silver-carbon (Ag-C) nanocomposite interlayer in anode-free setups. Based on the Li transport kinetics among the Ag-C interlayers, the interfacial configurations of Ag-C interlayers are classified as either exterior or internal. Furthermore, the review concludes with a discussion of the perspectives and future prospects, allowing for the improvement of interlayer techniques for solid-state batteries.

25 ENERGY STORAGE↗

DOE OSTI2021

Process intensification of CO 2 capture by low-aqueous solvent

Low-energy solvent-based CO 2 absorption processes have drawn attention as a next-generation post-combustion CO 2 capture technology to reduce CO2 emissions from fossil fuel– or biomass-fired power generation and industrial flue gas streams. A low-aqueous (or water-lean) solvent process may substantially reduce the thermal energy consumption for solvent regeneration. Low-aqueous solvent–based processes are thermally sensitive, requiring a delicate temperature control within the absorber because of the fast exothermic amine-CO 2 reaction and low heat capacity organic diluent. This reaction may result in heat accumulation in a packed absorption column and undesirable CO 2 desorption occurring as the solvent moves through the column, reducing the solvent’s CO 2 capture efficiency if its temperature is not controlled. Using a 3D printed intensified packing device, enhanced heat and mass transfer were demonstrated in an amine-CO 2 scrubbing process using low-aqueous solvent. The multifunctional intensified device facilitates contact of the reactive solvent and gas phases in a single stage and heat removal by a cooling fluid flowing through channels in the interior of the corrugated plates of the device. These functionalities led to effective thermal management along the column via intrastage cooling and significant improvement in CO 2 uptake under a wide range of operating conditions. Intrastage cooling effectively reduced the solvent average temperature along the column by ~10 °C and, as a result, the solvent’s capture efficiency improved by up to 25%.

42 ENGINEERING↗

DOE OSTI2024

High-throughput measurements of CO 2 permeance and solubility in ionic liquid reveal a synergistic role of ionic interactions and void fractions

The factors that govern CO 2 solubility in ionic liquids (ILs) are of great interest for the development of new materials for CO 2 capture and utilization. The cationic functional group (i.e., imidazolium, pyrrolidinium, pyridinium, etc.), alkyl chain length of cation, degree of fluorination of anion, anion size, and the void fraction in IL are known to influence CO 2 solubility. However, a comprehensive explanation of how these factors collectively affect CO 2 solubility has not been developed yet. This knowledge gap is largely attributed to the lack of CO 2 solubility data for IL structures other than imidazolium based ILs. We report here an automated high-throughput (HT) setup for the measurement of CO 2 solubility in room-temperature ILs (RTILs) combining six different anions and nine different cations for a total of 19 different specific ranges of RTILs. The HT setup first dispenses up to 200 µL of RTILs in a 96-well microtiter plate and then utilizes a robotic arm to measure cyclic voltammogram (CV) in each well using maneuverable Ag electrodes. The Cottrell analysis of the CO 2 reduction CV peak provides a direct measurement of CO 2 permeance in RTILs, which yields Henry’s constant from the estimated diffusion coefficient of CO 2 . Henry’s constants thus obtained are in very good agreement with those reported earlier. The measured CO 2 permeance and Henry’s constant of all RTILs seem to follow a first-order dependence on void fraction and a second-order dependence on electrostatic interaction between anion and cation of IL, with some synergistic dependence on the product of a void fraction and electrostatic interaction, making them two important descriptors for the design of novel ILs.

CO2 Solubility↗

DOE OSTI2021

Effects of organic additives on calcium hydroxide crystallisation during lime slaking

Highlights: • Sucrose and lignosulfonate reduce the crystallite size of Ca(OH){sub 2}. • Lime slaking in sucrose solutions leads to Ca(OH)2 with irregular shape. • Lime slaking in presence of lignosulfonate leads to plate-like Ca(OH){sub 2} crystals. • Effects of additives are enhanced when introduced before slaking. • Additives stabilise the unstable edge faces of Ca(OH){sub 2} during ageing. Organic compounds, often used in cement systems as admixtures, may affect the crystallisation and carbonation kinetics of Ca(OH){sub 2}, an important phase of hydrated cement. Here, we investigated changes in Ca(OH){sub 2} morphology in the presence of 3 organic compounds, commonly encountered in cement and lime-based materials: sucrose, pectin and calcium lignosulfonate. The additives were introduced either before or after lime slaking to determine the influence of temperature. Ca(OH){sub 2} crystals and supernatant solutions were characterised at time of slaking and after 6 months of ageing using scanning electron microscopy, X-ray diffraction and optical emission spectroscopy. Our results indicate that the morphology of Ca(OH){sub 2} crystals is modified by the characteristics of the organic molecules which promote formation of Ca(OH){sub 2} with habits that can result in faster carbonation, an effect that is detrimental to cement used in reinforced concrete. These effects are enhanced when the additives are introduced before slaking, likely as a result of thermal degradation.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Binder jetting additive manufacturing of silicon carbide ceramics: Development of bimodal powder feedstocks by modeling and experimental methods

A limitation of binder jetting additive manufacturing is the low density of fabricated parts. Mixing powders with different sizes is a promising approach to increase powder bed packing density and, hence, printed part density. However, in previous studies mixed powder feedstock was prepared by trial and error method. In this research, both modeling and experimental methods were used to prepare the bimodal powder feedstocks. Analytical packing model was introduced for irregular powders. A bimodal powder was prepared by mixing two different-sized silicon carbide powders (i.e. coarse and fine) using ball mill, and their tap densities were measured. Silicon carbide plates were printed using the coarse and bimodal powders by a commercial binder jetting system. Results showed that the modeling method could predict the tap density of bimodal powders with high accuracy. The printed parts from bimodal powder achieved higher green densities than those from the unimodal powder.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Simultaneous material, shape and topology optimization

Using three design fields we develop an optimization environment that can simultaneously optimize material, shape and topology. We use the implicit representation of the boundaries with level-set functions that define the shape and topology. Differentiable R-functions allow us to combine these shapes and topology descriptions with Boolean operations. Additionally, we incorporate design dependent-stiffness materials with another design field. Notably, this framework accommodates design dependent loads, has the ability to introduce holes, and ensures the satisfaction of optimality criteria. It builds upon the fictitious domain, ersatz material, material interpolation and level-set methods. Additionally, it also borrows from parameterized density-based topology optimization methods. Since analytical sensitivities can be computed, we use efficient nonlinear programming algorithms to update the design instead of the Hamilton–Jacobi’s scheme of level-set methods. We illustrate the features of our framework by designing a cantilever beam with octet truss microlattice, a dam with design-dependent loads, and a composite clevis plate.

42 ENGINEERING↗

DOE OSTI2025

Sizing comingled CF/PA 6 fibers with cellulose nanofibrils for enhanced performance properties

Compatibility between the reinforcing phase and the polymer matrix is critical to achieving the desired mechanical and thermal performance of composite materials. Several mechanisms can enhance this interfacial interaction, including surface treatments (e.g., oxidation, plasma, or irradiation), in-situ nanoparticle deposition, and fiber sizing. Here, in this study, cellulose nanofibrils (CNF) were employed as a sustainable sizing agent to modify the interface in commingled carbon fiber (CF)/polyamide 6 (PA 6) yarns, in which CF and PA6 filaments are intimately blended to enable simultaneous consolidation. A 0.25 wt% CNF aqueous suspension was applied under bath sonication to ensure uniform dispersion and minimize agglomeration. CNF-sized and unsized yarns were used to fabricate unidirectional composite plates via filament winding on a flat mandrel, followed by compression molding. Scanning electron microscopy confirmed CNF presence on both CF and PA6 filaments. CNF-sized composites exhibited increments in interlaminar shear strength (ILSS) by 50%, flexural strength by 11%, and tensile strength by 2.5% compared to unsized composites. Thermal analysis showed minimal changes in degradation temperature and crystallinity. These findings demonstrate that CNF sizing enhances interfacial bonding and mechanical performance, offering a scalable and environmentally friendly strategy for thermoplastic composite manufacturing along with yarn/tow handleability.

Cellulose nanofibrils (CNF)↗

DOE OSTI2025

Comparison of interlaminar damage modeling strategies for hybrid composite/aluminum laminates subjected to low-velocity impact

Low-velocity impact of hybrid metal-composite structures was investigated experimentally and computationally. Composite laminates consisting of 2D woven glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) were joined with a 6061-T6 aluminum plate using an epoxy adhesive. Two variations of the structure were studied; one consisting of all plies oriented at 0° and one consisting of all plies oriented at 45°. A drop tower was used to impact structures at a range of energies, including energies above and below the threshold at which the aluminum layer was perforated. Numerical simulations were implemented using Sierra/SM, an in-house transient dynamics finite element code developed at Sandia National Laboratories. A Hosford plasticity model was used to describe the response of the aluminum layer. A newly implemented orthotropic continuum damage mechanics (CDM) constitutive model was used to represent the composite laminate. This 3D-CDM model was compared to a cohesive zone model (2D-CDM/CZM) to investigate efficacy of aluminum perforation energy prediction, delamination prediction, and computational cost. Accuracy of each model was evaluated using the experimental results. Each showed good agreement with the tests for both the force and velocity histories, as well as the observed damage mechanisms. The 2D-CDM/CZM model was marginally more accurate in capturing both the composite and aluminum behavior — this model averaged error percentages of -11.2% and 10.8% for residual velocity and peak force, respectively. Meanwhile, the 3D-CDM model predictions yielded average error percentages of -35.5% (velocity) and 22.6% (force). However, the 3D-CDM model generally resulted in a decreased computational cost; the average run time was 14% shorter than the 2D-CDM/CZM model and 3x as many timesteps per hour were computed using the same computational resources. In conclusion, new experimental data on the impact and perforation resistance of metal-composite laminates is presented in addition to numerical predictions of the impact behavior.

Carbon fiber↗

DOE OSTI2024

Retrieving images from tarnished daguerreotypes using X-ray fluorescence imaging with an X-ray micro beam with tunable energy

We report recent observations using a synchrotron X-ray micro-beam to retrieve images from tarnished 19th century daguerreotypes. We confirm that high quality image can always be retrieved from tarnished plates using Hg L α XRF as long as the bulk of the image particles and their distribution remains intact. We also report results from using tunable tender X-rays (2 - 7 keV) to conduct imaging in high vacuum at energy above the Ag L-edge and the Hg M-edge, extracting images using Ag L α and Hg M α , respectively among others (e.g., S to track corrosion). Images obtained with the surface sensitive total electron yield (TEY) and the bulk sensitive fluorescence yield (FLY) as well as corresponding micro-XANES are reported. Flux tolerance to high intensity X-beam is also explored. These results and their implications for cultural heritage research are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Pressure effects on lithium anode/nickel-manganese-cobalt oxide cathode pouch cells through fixture design

Applying external pressure to a pouch cell results in improved performance, implicating systems-level design of batteries. Here, different formats and amounts of external pressure to Li-Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 (Li-NMC811) pouch cells were studied under lean electrolyte conditions. Due to the more uniform lithium plating/stripping, a constant gap fixture that retains the distance of the frame during cycling performed greater than a constant pressure fixture that retains applied pressure to the cell. In addition, the use of flexible foam in a constant gap fixture revealed enhanced cycle life at 10 psi; however, at 30 psi, the use of a rigid plate extended cycle life to over 250 cycles, while the foam severely shortened cycle life. This discrepancy with pressure was proven to be driven by stress distribution on cell components. The failure mechanisms and the effects of pressure fixture design on cell components were unveiled, shedding light on improving high-energy battery performance through at-scale fixture design.

25 - ENERGY STORAGE↗