Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Launch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Evaluation of the Performance Characteristics of the CGLSS and NLDN Systems Based on Two Years of Ground-Truth Data from Launch Complex 39B, Kennedy Space Center, Florida

From May 2011 through July 2013, the lightning instrumentation at Launch Complex 39B (LC39B) at the Kennedy Space Center, Florida, has obtained high-speed video records and field change waveforms (dE/dt and three-axis dH/dt) for 54 negative polarity return strokes whose strike termination locations and times are known with accuracy of the order of 10 m or less and 1 μs, respectively. A total of 18 strokes terminated directly to the LC39B lighting protection system (LPS), which contains three 181 m towers in a triangular configuration, an overhead catenary wire system on insulating masts, and nine down conductors. An additional 9 strokes terminated on the 106 m lightning protection mast of Launch Complex 39A (LC39A), which is located about 2.7 km southeast of LC39B. The remaining 27 return strokes struck either on the ground or attached to low-elevation grounded objects within about 500 m of the LC39B LPS. Leader/return stroke sequences were imaged at 3200 frames/sec by a network of six Phantom V310 high-speed video cameras. Each of the three towers on LC39B had two high-speed cameras installed at the 147 m level with overlapping fields of view of the center of the pad. The locations of the strike points of 54 return strokes have been compared to time-correlated reports of the Cloud-to-Ground Lightning Surveillance System (CGLSS) and the National Lightning Detection Network (NLDN), and the results of this comparison will be presented and discussed.

Waveforms↗

Launch Lock Mechanism for Resource Prospector Rover

The Resource Prospector Rover is being designed to carry the RESOLVE (Regolith Environment Science, and Oxygen Lunar Volatile Extraction) payload on a mission to the Moon to prospect for water ice. This is a joint project between KSC Swamp Works UB-R1 and JSC. JSC is building the Resource Prospector 2015 (RP15) rover and KSC designed and fabricated a Launch-Lock (LL) hold down mechanism for the rover. The LL mechanism will attach and support the rover on a Lunar Lander during launch and transit to the moon, then release the RP15 rover after touchdown on the lunar surface. This report presents the design and development of the LL mechanism and its unique features which make it suitable for this lunar exploration mission. An EDU (engineering development unit) prototype of the LL has been built and tested at KSC which is the subject of this paper.

Lunar Lander↗

CubeSat Launch Initiative

The National Aeronautics and Space Administration (NASA) recognizes the tremendous potential that CubeSats (very small satellites) have to inexpensively demonstrate advanced technologies, collect scientific data, and enhance student engagement in Science, Technology, Engineering, and Mathematics (STEM). The CubeSat Launch Initiative (CSLI) was created to provide launch opportunities for CubeSats developed by academic institutions, non-profit entities, and NASA centers. This presentation will provide an overview of the CSLI, its benefits, and its results.

CubeSat↗

Launch and Commissioning of the Deep Space Climate Observatory

The Deep Space Climate Observatory (DSCOVR), formerly known as Triana, successfully launched on February 11th, 2015. To date, each of the five space-craft attitude control system (ACS) modes have been operating as expected and meeting all guidance, navigation, and control (GN&C) requirements, although since launch, several anomalies were encountered. While unplanned, these anomalies have proven to be invaluable in developing a deeper understanding of the ACS, and drove the design of three alterations to the ACS task of the flight software (FSW). An overview of the GN&C subsystem hardware, including re-furbishment, and ACS architecture are introduced, followed by a chronological discussion of key events, flight performance, as well as anomalies encountered by the GN&C team.

DSCOVR↗

Nanosatellite Launch Adapter System (NLAS) Overview

An overview of the Nanosatellite Launch Adapter System (NLAS) is provided that contains information on NLAS' objectives and relevance, structural components and position in the launch vehicle stack, and details on its three main components.

Launch adapter↗

Sensitivity of the Asteroid Redirect Robotic Mission (ARRM) to Launch Date and Asteroid Stay Time

National Aeronautics and Space Administrations (NASAs) proposed Asteroid Redirect Mission (ARM) is being designed to robotically capture and then redirect an asteroidal boulder into a stable orbit in the vicinity of the moon, where astronauts would be able to visit and study it. The current reference trajectory for the robotic portion, ARRM, assumes a launch on a Delta-IV H in the end of the calendar year 2021, with a return for astronaut operations in cislunar space in 2026. The current baseline design allocates 245 days of stay time at the asteroid for operations and boulder collection. This paper outlines analysis completed by the ARRM mission design team to understand the sensitivity of the reference trajectory to launch date and asteroid stay time.

asteroid↗

CubeSat Launch Initiative Overview and CubeSat 101

The National Aeronautics and Space Administration (NASA) recognizes the tremendous potential that CubeSats (very small satellites) have to inexpensively demonstrate advanced technologies, collect scientific data, and enhance student engagement in Science, Technology, Engineering, and Mathematics (STEM). The CubeSat Launch Initiative (CSLI) was created to provide launch opportunities for CubeSats developed by academic institutions, non-profit entities, and NASA centers. This presentation will provide an overview of the CSLI, its benefits, and its results. This presentation will also provide high level CubeSat 101 information for prospective CubeSat developers, describing the development process from concept through mission operations while highlighting key points that developers need to be mindful of.

Launching↗

A Prognostic Launch Vehicle Probability of Failure Assessment Methodology for Conceptual Systems Predicated on Human Causal Factors

Lessons learned from past failures of launch vehicle developments and operations were used to create a new method to predict the probability of failure of conceptual systems. Existing methods such as Probabilistic Risk Assessments and Human Risk Assessments were considered but found to be too cumbersome for this type of system-wide application for yet-to-be-flown vehicles. The basis for this methodology were historic databases of past failures, where it was determined that various faulty human-interactions were the predominant root causes of failure rather than deficient component reliabilities evaluated through statistical analysis. This methodology contains an expert scoring part which can be used in either a qualitative or a quantitative mode. The method produces two products: a numerical score of the probability of failure and guidance to program management on critical areas in need of increased focus to improve the probability of success. In order to evaluate the effectiveness of this new method, data from a concluded vehicle program (USAF's Titan IV with the Centaur G-Prime upper stage) was used as a test case. The theoretical vs. actual probability of failure was found to be 4.46% vs. 6.67% respectively. Recommendations are made for future applications of this method to ongoing launch vehicle development programs.

Launch Vehicle↗

High-Resolution Launch Environment Simulations

After many years of harsh rocket launches, the Main Flame Deflector (MFD) at Kennedy Space Center has been upgraded in anticipation of flights of NASA’s next generation Space Launch System. The new MFD has a much easier to maintain shingled steel surface.

Launch↗

Space Launch System Engine Out Capabilities

NASA's SLS is being developed with the primary purpose of returning people to the Moon and eventually landing people on Mars. With these lofty goals, ensuring mission completion is paramount even in the event of an in-flight mishap. One possible mishap is the loss of an engine in flight. While SLS was not required to show full engine out capability, the program took an ``assess to'' approach to see when the launch vehicle could complete the mission after an engine failure versus when the launch vehicle targets required a down-mode to an alternate mission target to ensure at least some flight objectives were complete, or at a minimum ensure safe return of Orion and the Crew. While this paper will focus on Artemis I, an uncrewed mission, some comparisons will be made to how the engine out capability will change for the subsequent Crewed flights of SLS and Orion.

Space Launch System↗

Alternating Between Software Models and Real Hardware in the System Integration Lab for theIncremental Development of the Space Launch System Program Avionics

The MSFC System Integration Lab (SIL) supports avionics development of NASA’s Space Launch System—a new U.S. heavy-lift launch vehicle for NASA’s next generation of human space exploration beyond low-Earth orbit. The SIL facility allows for the incremental development of system components by either hosting real hardware in the loop and/or software models of those components. Through this functionality test teams are able to evaluate overall system performance as components are designed, built and modified. Early hardware/software integration and testing reduces risks and saves overall cost and schedule throughout a program/project life cycle. By performing early hardware/software integration, potential architecture and interface-related problems can be identified, and thus reduce associated risk as early in the design cycle as possible when problems are the least expensive to resolve while also improving the design and requirements. This presentation will illustrate the power of employing a hardware in the loop simulation system for the development of novel spacecraft avionics.

Space Launch System↗

Advanced Materials Testing for Lunar Landing & Launch Pad Construction

Five candidate lunar landing and launch pad candidate materials were evaluated in relevant Oxygen/Methane rocket engine plume environment exposure tests. The performance trends were modeled, observed, measured (to the extent possible), and testing results were evaluated. A total of fifteen high temperature plume tests were performed in two test campaigns: five in December 2020 and ten in March 2021. The results indicate that several of the selected materials are promising for future consideration in designing and building lunar landing and launch pads, although further development work is needed for all of them.

landing pad↗

Development of Advanced Manufacturing Approaches for Single-Piece Launch Vehicle Structures

Advanced, near-net shape manufacturing methods have the potential to enable production of structures with fewer welds and reduced machining requirements. Two such methods that are suitable for the manufacturing of single-piece, stiffened barrel-shaped structures are presented. The first solution deployed existing manufacturing technology to produce a thick-walled barrel with integrally machined stiffeners. In this study, an 8-ft. diameter barrel was produced and subjected to a buckling test. Data on the manufacturing and testing of this barrel are provided and compared against the traditional multi-piece weld construction approach. The single-piece barrel resulted in a 28% greater load carrying capacity than the welded barrel. A second solution utilized a novel flow-forming technique to produce the barrel and stiffeners in one process without the need for welding or machining. This is an emerging manufacturing method known as the Integrally Stiffened Cylinder (ISC) process. This innovative process is being evaluated for launch vehicle and commercial aircraft manufacturing. The one-piece, stiffened ISC barrels, which have been successfully fabricated at 10 ft. in diameter, offer a direct replacement for conventional multi-piece, welded or riveted structures. A cost-benefit analysis for launch vehicle cryogenic propellant tanks estimated that the ISC process offers up to a 50% reduction in manufacturing costs and a 10% reduction in mass.

integrally stiffened cylinder (ISC)↗

In-situ Lunar Launch and Landing Pad Construction with Regolith-Thermoset Polymer Composite Materials

Lunar launch and landing pads are necessary to mitigate risks to lander/ascent vehicles and surrounding surface assets from rocket plume ejected regolith. The current state of the art of landing and launching from the lunar surface is to land/launch on unprepared regolith surfaces. Significant risks exist for the larger landers proposed for the Artemis Program due to higher thrust levels leading to increased ejecta and cratering, presence of co-located assets in the ejecta path, and potential strict surface levelness requirements for tall vehicles.

Launch Pad↗

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗

Air Sparge Pilot Study in the DNAPL Source Zone at Launch Complex 34

Multiple releases of trichloroethene (TCE) occurred at Launch Complex 34 (LC34) between the late 1950s and 1968. A 2007 conceptual site model estimated a 2-acre dense non-aqueous phase liquid (DNAPL) source area with mass in excess of 90,000 pounds, nearly 40 years after termination of launch activities. Located on a barrier island, LC34 currently has no complete exposure pathways and a historical groundwater flow radial from the DNAPL source zone (DSZ), the focus area of this study. The geology at LC34 is classified as Layers 1 through 9 with each layer representing a different lithology. These lithologies contribute to large variations in hydraulic conductivity (1x10-3 cm/sec to 1x10-8 cm/sec) with notable fine-grained units at Layer 4 (sandy clay) and Layer 7 (fine silty sand). Historically, technologies implemented at LC34 have been split vertically based on technology limitations and lithology. Remedial technologies have been evaluated to control and/or remediate the DSZ in the past; however, more aggressive technologies required significant cost and would likely leave considerable mass. Thus, an adaptive site management strategy has been implemented that adopts a treatment train approach which began in 2009 with hydraulic containment via pump and treat to control mass discharge from the DSZ while removing mass as a secondary benefit. Concurrently, hot spot areas in the larger dissolved plume are being treated by air sparging to reduce overall mass and the plume footprint. In 2019, a re-characterization of the DSZ was completed to update conditions in support of implementing more aggressive technologies as part of the treatment train approach. The results showed that the DSZ remained relatively the same size but with a slightly different morphology. Moreover, data showed that the fine-grained units (Layers 4 and 7) are storing most of the remaining mass, with TCE concentrations suggestive of DNAPL extending into Layer 7 (approximately 80 to 100 ft below land surface). Based on the current conditions, more aggressive technologies are still cost prohibitive; therefore, a different approach is warranted to determine the next implementable step in the treatment train. Air sparging is being proposed as a technology alternative based on several factors including lower treatment costs. A pilot study was conducted to test the feasibility of air sparging in the DSZ as the next step in the treatment train for that area.

Launch Complex 34↗

NASA Engineering and Safety Center Technical Bulletin No. 22-05: Launch Vehicle Flight Control Stability Margin Reduction Considerations

Launch vehicle ascent stability analyses typically rely on a combination of frequency and time domain analyses. Frequency domain analysis uses a sequence of high-fidelity linear models with constant parameters spanning the ascent trajectory. Complementary time domain analysis is performed using high-fidelity, nonlinear 6-DOF simulations. Analyses are typically dispersed to verify robustness to parameter variations by showing the vehicle meets frequency domain stability margin requirements and time domain performance metrics. This Technical Bulletin outlines standard stability margin best practices and provides recommendations for treatment of deviations from industry-standard launch vehicle stability margins due to vehicle flexibility, slosh dynamics, aerodynamics, other offending dynamics, or coupling thereof.

Launch Vehicle↗