Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IRRADIATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Analysis and synthesis of the variability of irradiance and PV power time series with the wavelet transform

The irradiance fluctuations and the subsequent variability of the power output of a PV system are analysed with some mathematical tools based on the wavelet transform. It can be shown that the irradiance and power time series are nonstationary process whose behaviour resembles that of a long memory process. Besides, the long memory spectral exponent {alpha} is a useful indicator of the fluctuation level of a irradiance time series. On the other side, a time series of global irradiance on the horizontal plane can be simulated by means of the wavestrapping technique on the clearness index and the fluctuation behaviour of this simulated time series correctly resembles the original series. Moreover, a time series of global irradiance on the inclined plane can be simulated with the wavestrapping procedure applied over a signal previously detrended by a partial reconstruction with a wavelet multiresolution analysis, and, once again, the fluctuation behaviour of this simulated time series is correct. This procedure is a suitable tool for the simulation of irradiance incident over a group of distant PV plants. Finally, a wavelet variance analysis and the long memory spectral exponent show that a PV plant behaves as a low-pass filter. (author)

14 SOLAR ENERGY↗

Linear complexions enable unprecedented ductility retention in neutron irradiated ferritic steel

Herein, the operando formation of Si-enriched linear complexions during neutron irradiation enables Grade 91 ferritic steel to overcome the strength–ductility tradeoff, one of the most critical life-limiting challenges facing nuclear structural alloys. Linear complexions are a distinct yet confined chemical and structural state at a dislocation, which are rarely reported in engineering alloys. Ferritic steels are amongst the most ubiquitous engineering alloys for current and future nuclear components, but they are susceptible to irradiation hardening and embrittlement. Here, exceptional ductility retention exceeding 90% of pre-irradiation levels is obtained in Grade 91 synthesized using powder metallurgy with hot isostatic pressing (PM-HIP). Powder processing artifacts promote a high density of screw dislocation arrays, on which β-FeSi 2 linear complexions form due to Si segregation during irradiation. Screw dislocation dipoles undergo pinning and unpinning on linear complexions, resulting in extended yielding and significant ductility retention post-irradiation. These findings represent a significant advancement toward design of alloys and manufacturing processes that can autonomously self-regulate their microstructural resilience in-operando during irradiation, enabling exceptional ductility rather than embrittlement.

Chatterjee, Arya [University of Illinois, Urbana, ↗

Machine learning predictions of irradiation embrittlement in reactor pressure vessel steels

Abstract Irradiation increases the yield stress and embrittles light water reactor (LWR) pressure vessel steels. In this study, we demonstrate some of the potential benefits and risks of using machine learning models to predict irradiation hardening extrapolated to low flux, high fluence, extended life conditions. The machine learning training data included the Irradiation Variable for lower flux irradiations up to an intermediate fluence, plus the Belgian Reactor 2 and Advanced Test Reactor 1 for very high flux irradiations, up to very high fluence. Notably, the machine learning model predictions for the high fluence, intermediate flux Advanced Test Reactor 2 irradiations are superior to extrapolations of existing hardening models. The successful extrapolations showed that machine learning models are capable of capturing key intermediate flux effects at high fluence. Similar approaches, applied to expanded databases, could be used to predict hardening in LWRs under life-extension conditions.

36 MATERIALS SCIENCE↗

Amorphization and dynamic annealing of hexagonal SiC upon heavy-ion irradiation: Effects on swelling and mechanical properties

Structural, mechanical, and dimensional evolutions of silicon carbide (SiC) induced by heavy-ion irradiations are studied by means of Rutherford backscattering spectrometry and channeling (RBS/C), nanoindentation, and surface profilometry measurements. 4H- and 6H-SiC single crystals were irradiated with 4 MeV Au{sup 2+} and 4 MeV Xe{sup +} ions at room temperature (RT) or 400 deg. C. Using a Monte Carlo program to simulate the RBS/C spectra (MCCHASY code), we find that Au ion irradiation at RT induces a total silicon sublattice disorder related to full amorphization at a dose of about 0.4 displacement per atom (dpa). A two-step damage process is found on the basis of the disordered fractions deduced from RBS/C data. Complete amorphization cannot be reached upon both Au and Xe ion irradiations at 400 deg. C up to about 26 dpa because of the dynamic annealing of defects. When complete amorphization is reached at RT, the Young's modulus and Berkovich hardness of irradiated 6H-SiC samples are lower by, respectively, 40% and 45% than those of the virgin crystals. The out-of-plane expansion measured by surface profilometry increases versus irradiation dose and the saturation value measured in the completely amorphous layer (normalized to the ion projected range) is close to 25%. We show that the modifications of the macroscopic properties are mainly due to the amorphization of the material. The macroscopic elasticity constants and dimensional properties are predicted for a composite material made of crystalline matrix containing dispersed amorphous inclusions using simple analytical homogenization models. Voigt's model seems to give the best approximation for disordered fractions larger than 20% in the second step of the damage process.

36 MATERIALS SCIENCE↗

Effects of electron-irradiation on electrical properties of AlGaN/GaN Schottky barrier diodes

Effects of 1 MeV electron-irradiation at room temperature on the electrical properties of AlGaN/GaN heterostructures, including leakage currents, threshold voltages, and electron traps, have been investigated using Schottky barrier diodes (SBDs) fabricated on the AlGaN. The SBDs, before and after the irradiation with a dose of 5x10{sup 15} cm{sup -2}, were characterized by temperature dependent current-voltage and capacitance-voltage measurements and deep level transient spectroscopy. It is found that the irradiation causes (i) significant increase in leakage currents, dominated by tunneling conduction, at both reverse and low-forward biases; (ii) a clear negative shift in threshold voltage in the pinch-off region; and (iii) creation of traps A{sub e}(approx1.1 eV) or A{sub 2}(1.2 eV) and E{sub e}(0.09 eV) in the GaN buffer and AlGaN regions. The irradiation-induced traps can be used to account for the increase in leakage currents and shift in threshold voltage. However, as compared to traps A{sub 2}(1.2 eV) and E(0.13 eV) induced in thick GaN layers by electron-irradiation, the irradiation-induced traps in the AlGaN/GaN heterostructures show some changes in activation energy and electron capture behavior.

36 MATERIALS SCIENCE↗

Charge transportation and permittivity in electron beam irradiated polymethyl methacrylate

The charging phenomenon in the insulating dielectrics often occurs in the radiative environments such as in the outer space and in the nuclear reactor. Both surface charging and bulk charging have various influences on the dielectric properties. Understanding electrical properties of e-beam irradiated dielectrics is of great significance in order to maintain the stability and reliability of the related operating system. In this work, the effect of electron beam irradiation on the permittivity of polymethyl methacrylate (PMMA) samples was investigated. It was found that the variance of permittivity in e-beam irradiated PMMA is mainly determined by two factors. One is the porosity of the material. The irradiating process could increase the porosity of PMMA due to the escape of the small molecule (e.g., CO, CO{sub 2}, and CH{sub 4}) produced during material degradation caused by e-beam irradiation. The enhanced higher porosity corresponds to lower permittivity. The distribution of the implanted charge is the other factor that influences the permittivity. When the distribution of electric field generated by the accumulating charge is asymmetric for the middle thickness of the sample, the PMMA sample with polar groups would be subjected to extra polarization by the field, which could lead to the increase in permittivity. Combining with the model of Wakino et al. [J. Am. Ceram. Soc. 76, 2588 (1993)] on permittivity of mixture materials, the Clausius-Mosotti equation was utilized to analyze the variation in permittivity in the e-beam irradiated PMMA samples.

36 MATERIALS SCIENCE↗

Lateral propagation of MeV electrons generated by femtosecond laser irradiation

The propagation of MeV electrons generated by intense (approx =10{sup 20} W/cm{sup 2}) femtosecond laser irradiation, in the lateral direction perpendicular to the incident laser beam, was studied using targets consisting of irradiated metal wires and neighboring spectator wires embedded in electrically conductive (aluminum) or resistive (Teflon) substrates. The K shell spectra in the energy range 40-60 keV from wires of Gd, Dy, Hf, and W were recorded by a transmission crystal spectrometer. The spectra were produced by 1s electron ionization in the irradiated wire and by energetic electron propagation through the substrate material to the spectator wire of a different metal. The electron range and energy were determined from the relative K shell emissions from the irradiated and spectator wires separated by varying substrate lateral distances of up to 1 mm. It was found that electron propagation through Teflon was inhibited, compared to aluminum, implying a relatively weak return current and incomplete space-charge neutralization. The energetic electron propagation in the direction parallel to the electric field of the laser beam was larger than perpendicular to the electric field. Energetic electron production was lower when directly irradiating aluminum or Teflon compared to irradiating the heavy metal wires. These experiments are important for the determination of the energetic electron production mechanism and for understanding lateral electron propagation that can be detrimental to fast-ignition fusion and hard x-ray backlighter radiography.

74 ATOMIC AND MOLECULAR PHYSICS↗

Effects of irradiation and annealing on deep levels in rhodium-doped p-GaAs grown by metal-organic chemical-vapor deposition

This paper reports a detailed study of the effects of irradiation and thermal annealing on deep levels in Rh-doped p-type GaAs grown by low-pressure metal-organic chemical-vapor deposition, using deep level transient spectroscopy (DLTS) technique. It is found upon irradiation with alpha particles that, in addition to the radiation-induced defect peaks, all the Rh-related peaks observed in majority, as well as minority-carrier emission DLTS scans show an increase in their respective concentrations. The usually observed {alpha}-induced defects H{alpha}1, H{alpha}2, and H{alpha}3 are found to have lower introduction rates in Rh-doped samples, as compared to reference samples (not doped with Rh). Alpha-irradiation has been found to decompose the two minority carrier emitting bands (one at low temperature {approx}150 K and the other at {approx}380 K) observed prior to irradiation into distinct peaks corresponding to deep levels Rh1 and Rh2 and EL2 and Rh3, respectively. A similar effect is also observed for the majority-carrier emitting band composed of hole emission from deep levels RhA and RhB, which separate out well upon irradiation. Further, from the double-correlation DLTS measurements, the emission rates of carriers from the radiation-enhanced peaks corresponding to deep levels Rh1, Rh2, Rh3, and RhC were found to be dependent on junction electric field. For RhC, the field dependence data have been analyzed in terms of the Poole-Frenkel model employing a 3-dimensional Coulomb potential with q = 2e (electronic charge). Temperature dependence of the hole capture cross-sections of the levels RhA and RhC was also studied quantitatively. The observed dependence of the hole capture cross-section of RhC on temperature can be interpreted in terms of multiphonon capture model, yielding a capture barrier of 0.2 eV and {sigma}({infinity}) = 2.3 x 10{sup -14} cm{sup 2}. The results of irradiation and isochronal thermal annealing study, in combination with the theoretical analysis of the field dependence of hole emission data, lead us to interpret the levels RhA and RhB as charged centers and probably complexes of arsenic anti-site defect (As{sub Ga}) with Rh-impurity, (As{sub Ga}-Rh). The levels Rh1 and Rh2 are also proposed to be complexes, albeit of a different type, of arsenic anti-site defects (As{sub Ga}) and Rh-impurity (As{sub Ga}-Rh), while the level RhC is likely to be a doubly-charged complex center composed of arsenic interstitial (I{sub As}) and Rh-impurity (I{sub As}-Rh).

36 MATERIALS SCIENCE↗

Cavity morphology in a Ni based superalloy under heavy ion irradiation with cold pre-injected helium. I

In order to understand radiation damage in the nickel based superalloy Inconel X-750 in thermal reactors, where (n, α) transmutation reaction also occurred in addition to fast neutron induced atomic displacement, heavy ion (1 MeV Kr{sup 2+}) irradiation with pre-injected helium was performed under in-situ observations of an intermediate voltage electron microscope at Argonne National Laboratory. By comparing to our previous studies using 1 MeV Kr{sup 2+} irradiation solely, the pre-injected helium was found to be essential in cavity nucleation. Cavities started to be visible after Kr{sup 2+} irradiation to 2.7 dpa at ≥200 °C in samples containing 200 appm, 1000 appm, and 5000 appm helium, respectively, but not at lower temperatures. The cavity growth was observed during the continuous irradiation. Cavity formation appeared along with a reduced number density of stacking fault tetrahedra, vacancy type defects. With higher pre-injected helium amount, a higher density of smaller cavities was observed. This is considered to be the result of local trapping effect of helium which disperses vacancies. The average cavity size increases with increasing irradiation temperatures; the density reduced; and the distribution of cavities became heterogeneous at elevated temperatures. In contrast to previous characterization of in-reactor neutron irradiated Inconel X-750, no obvious cavity sink to grain boundaries and phase boundaries was found even at high doses and elevated temperatures. MC-type carbides were observed as strong sources for agglomeration of cavities due to their enhanced trapping strength of helium and vacancies.

36 MATERIALS SCIENCE↗

Impact of total ionizing dose irradiation on electrical property of ferroelectric-gate field-effect transistor

P-type channel metal-ferroelectric-insulator-silicon field-effect transistors (FETs) with a 300 nm thick SrBi{sub 2}Ta{sub 2}O{sub 9} ferroelectric film and a 10 nm thick HfTaO layer on silicon substrate were fabricated and characterized. The prepared FeFETs were then subjected to {sup 60}Co gamma irradiation in steps of three dose levels. Irradiation-induced degradation on electrical characteristics of the fabricated FeFETs was observed after 1 week annealing at room temperature. The possible irradiation-induced degradation mechanisms were discussed and simulated. All the irradiation experiment results indicated that the stability and reliability of the fabricated FeFETs for nonvolatile memory applications will become uncontrollable under strong irradiation dose and/or long irradiation time.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Critical phenomena of the layered ferrimagnet Mn 3 Si 2 Te 6 following proton irradiation

The critical phenomena and magnetic entropy of the quasi-2D ferrimagnetic crystal, Mn 3 Si 2 Te 6 (MST), is analyzed along the easy axis (H || ab) as a function of proton irradiance. The critical exponents β and γ do not fall into any particular universality class upon proton irradiation. However, for pristine and irradiated samples, the critical exponents lie closer to mean field-like interactions; therefore, long-range interactions are presumed to be sustained in MST. The effective spatial dimensionality reveals that MST remains at d =3 under proton irradiation, whereas spin dimensionality transitions from an initial n =1 to n =2 and n =3 for 1 × 10 15 and 5 × 10 15 H + /cm 2 , indicating XY and Heisenberg interactions, respectively. The spin correlation function reveals an increase in magnetic correlations at 5 × 10 15 H + /cm 2 . Maximum change in magnetic entropy at 3 T is the largest for 5 × 10 15 H + /cm 2 at 2.45 J/kg K, in comparison to 1.60 J/kg K for pristine MST. These results intriguingly align with previous findings on MST where magnetization increased by ~50% at 5 × 10 15 H + /cm 2 , in comparison to its pristine counterpart [Martinez et al., Appl. Phys. Lett. 116, 172404 (2020)]. Magnetic entropy derived from heat capacity analysis shows no large deviations across the proton irradiated samples suggesting that the antiferromagnetic (AFM) coupling between the Mn sites is stable even after proton irradiation. This implies that magnetization is enhanced through a strengthening of the super-exchange interaction between Mn atoms mediated through Te rather than a weakening of the AFM component.

2D materials↗

Electron irradiation effects on the optical properties of Hf- and Zn-doped β -Ga 2 O 3

Optical and electrical properties of Hf- and Zn-doped β-Ga 2 O 3 samples, which are n-type and insulating, respectively, were altered via high-energy electron irradiation at 2.5 or 0.5 MeV. The β-Ga 2 O 3 :Hf samples irradiated with 2.5 MeV electrons experienced a color change from blue to yellow and a large drop in conductivity, attributed to the creation of gallium vacancies, which compensate donors. This irradiation resulted in the absence of free carrier absorption and the presence of Cr 3+ photoluminescence (PL). PL mapping prior to irradiation revealed optically active ZnO precipitates that formed during the growth of β-Ga 2 O 3 :Zn. These precipitates have a 384 nm (3.23 eV) stacking fault emission in the core; in the outer shell of the precipitate, the PL blue-shifts to 377 nm (3.29 eV) and a broad defect band is observed. After 0.5 MeV electron irradiation, the defect band broadened and increased in intensity. The blue PL band (435 nm) of β-Ga 2 O 3 was enhanced for both Hf- and Zn-doped samples irradiated with 0.5 MeV. This enhancement is correlated with an increase in oxygen vacancies.

36 MATERIALS SCIENCE↗

Temperature effects of ion irradiation on the nanostructural features in ductile-phase-toughened tungsten composites

Ductile-phase toughened tungsten (DPT W) composites have emerged as promising candidates for load-bearing components behind the plasma-facing tungsten armor in fusion reactors due to their enhanced thermomechanical properties. This study focuses on a composite consisting of W particles embedded in a ductile NiFeW solution matrix, hot-rolled to a thickness reduction of 87% (87R DPT W). Sequential irradiations with Ni2+ and He+ ions were performed to identical doses and helium concentrations at room temperature (RT) and 1273 K. Irradiation at RT produced no discernible nanostructural features due to the immobility of mono-vacancies, whereas cavity formation was observed at 973 K. At 1273 K, the W phase exhibited larger cavities, reduced cavity number density, and lower volumetric swelling compared to 973 K. Notably, nanosized NiFeW precipitates formed within the W phase at 1273 K, a phenomenon absent at 973 K. A new phase of cubic (NiFe)6W6C was also observed at the interphase boundary. In contrast, the NiFeW matrix showed no nanostructural changes at 1273 K, likely due to cavity dissociation. Separate irradiations at 1273 K indicated that Ni2+ ions induced precipitate formation in the W phase, while He+ ions exclusively caused cavity formation. The microstructure of 87R DPT W irradiated at RT and subsequently annealed at 1273 K closely resembled that of material irradiated directly at 1273 K. Like oxide-dispersion-strengthened steels, the observed nanoparticle-embedded W can inhibit dislocation propagation, potentially delaying the ductile-to-brittle transition temperature. These findings highlight the potential of NiFeW nanoparticle-reinforced W composites as irradiation-resistant materials for fusion reactors.

Jiang, Weilin (ORCID:0000000183028313)↗

Crystal plasticity modeling of irradiation growth in Zircaloy-2

A reaction-diffusion based mean field rate theory model is implemented in the viscoplastic self-consistent (VPSC) crystal plasticity framework to simulate irradiation growth in hcp Zr and its alloys. A novel scheme is proposed to model the evolution (both number density and radius) of irradiation-induced dislocation loops that can be informed directly from experimental data of dislocation density evolution during irradiation. This framework is used to predict the irradiation growth behavior of cold-worked Zircaloy-2 and trends compared to available experimental data. The role of internal stresses in inducing irradiation creep is discussed. Effects of grain size, texture, and external stress on the coupled irradiation growth and creep behavior are also studied.

36 MATERIALS SCIENCE↗

Electron-irradiation induced creep in amorphous alloys

Electron-irradiation induced creep rates in amorphous alloys, a-SiO2, Fe79B16Si5, Cu60Ta40, and Cu50Ti50, were measured at room temperature using a miniaturized beam-bending apparatus within a transmission electron microscope operated at 200 keV. The creep rates of these amorphous samples increased nearly linearly with both e-beam current density and applied stress, while a reference crystalline (c-)SiO2 sample failed to creep under the same conditions. The irradiation induced creep compliance of a-SiO2 was ~ 15 times larger than that of Fe79B16Si5 and over 1,000 times larger than that of the two Cu alloys. Molecular dynamics computer simulations were employed to simulate electron irradiation induced creep using interatomic potentials representing amorphous Cu75Zr25, Ni80P20, and SiO2 as model systems. The irradiation induced creep compliances calculated for Cu75Zr25 during 200 keV electron irradiation provided good quantitative agreement with the two Cu-based alloys, but that for a-SiO2 was ~ 180 times too small. These results indicate that unlike neutron or ion-beam induced creep in a-SiO2, creep under electron irradiation is dominated by the effects of ionization owing largely to the far higher ratio of electronic stopping to nuclear stopping for electrons than for ions.

36 MATERIALS SCIENCE↗

Swift heavy ion irradiation induced magnetism in magnetically frustrated BiMn{sub 2}O{sub 5} thin films

The swift heavy ion (SHI) irradiation induces weak ferrimagnetism (FM) in magnetically frustrated polycrystalline BiMn{sub 2}O{sub 5} thin films. This is manifested from irradiation induced higher energetic configuration that accounts for evolution of the Mn{sup 2+} state in the Mn{sup 3+}/Mn{sup 4+} network. Basically, this is the root of large magnetic moment in the irradiated samples. X-ray diffraction and Raman-scattering data of the samples indicate considerable modifications in the crystal structure after the SHI irradiation. FM in the irradiated samples and magnetically frustrated behavior of the pristine sample is apparent from dc magnetization measurements. Element specific characterizations such as near-edge x-ray absorption fine structure spectroscopy at O K and Mn L{sub 3,2} edges along with x-ray magnetic circular dichroism at Mn L{sub 3,2} edge show the evolution of the Mn{sup 2+} at disbursement of the Mn{sup 4+}. The microscopic origin behind the induced weak FM is found to be the increased orbital moment in the irradiated thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure and migration of heavily irradiated grain boundaries and dislocations in Ni in the athermal limit

The microstructural evolution at and near preexisting grain boundaries (GBs) and dislocations in materials under high radiation doses is still poorly understood. In this work, we use the creation relaxation algorithm (CRA) developed for atomistic modeling of high-dose irradiation in bulk materials to probe the athermal limit of saturation of GB and dislocation core regions under irradiation in fcc Ni. We find that, upon continuously subjecting a single dislocation or GB to Frenkel pair creation in the athermal limit, a local steady-state disordered defect structure is reached with excess properties that fluctuate around constant values. Case studies are given for a straight screw dislocation which elongates into a helix under irradiation and several types of low- and high-angle GBs, which exhibit coupled responses such as absorption of extrinsic dislocations, roughening, and migration. A positive correlation is found between the initial GB energy and the local steady-state GB energy under irradiation across a wide variety of GB types. Metastable GB structures with similar density in the defect core region but different initial configurations are found to converge to the same limiting structure under CRA. The mechanical responses of pristine and irradiated dislocations and GB structures are compared under an applied shear stress. Irradiated screw and edge dislocations are found to exhibit a hardening response, migrating at larger flow stresses than their pristine counterparts. Mobile GBs are found to exhibit softening or hardening responses depending on GB character. Although some GBs recover their initial pristine structures upon migration outside of the radiation zone, many GBs sustain different flow stresses corresponding to altered mobile core structures.

36 MATERIALS SCIENCE↗

Stochastic Short-term High-resolution Prediction of Solar Irradiance and Photovoltaic Power Output

The increased penetration of solar photovoltaic (PV) energy sources into electric grids has increased the need for accurate modeling and prediction of solar irradiance and power production. Existing modeling and prediction techniques focus on long-term low-resolution prediction over minutes to years. This paper examines the stochastic modeling and short-term high-resolution prediction of solar irradiance and PV power output. We propose a stochastic state-space model to characterize the behaviors of solar irradiance and PV power output. This prediction model is suitable for the development of optimal power controllers for PV sources. A filter-based expectation-maximization and Kalman filtering mechanism is employed to estimate the parameters and states in the state-space model. The mechanism results in a finite dimensional filter which only uses the first and second order statistics. The structure of the scheme contributes to a direct prediction of the solar irradiance and PV power output without any linearization process or simplifying assumptions of the signal’s model. This enables the system to accurately predict small as well as large fluctuations of the solar signals. The mechanism is recursive allowing the solar irradiance and PV power to be predicted online from measurements. The mechanism is tested using solar irradiance and PV power measurement data collected locally in our laboratory.

Olama, Mohammed M.↗