Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite element model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Scale bridging damage model for quasi-brittle metals informed with crack evolution statistics

Computationally efficient methods for bridging length scales, from highly resolved micro/meso-scale models that can explicitly model crack growth, to macro-scale continuum models that are more suitable for modeling large parts, have been of interest to researchers for decades. In this work, an improved brittle damage model is presented for the simulation of dynamic fracture in continuum scale quasi-brittle metal components. Crack evolution statistics, including the number, length, and orientation of individual cracks, are extracted from high-fidelity, finite discrete element method (FDEM) simulations and used to generate effective material moduli that reflect the material’s damaged state over time. This strategy allows for the retention of small-scale physical behaviors such as crack growth and coalescence in continuum scale hydrodynamic simulations. However, the high-fidelity simulations required to generate the crack statistics are computationally expensive. Thus, steps were taken to produce a flexible constitutive model to reduce the number of costly high-fidelity simulations needed to produce accurate results. A new stress based degradation criterion is introduced for the degradation of individual material zones. This allows for the development of a heterogeneous damage distribution within the bulk material. Then a flow stress model is added to the hydrodynamic simulation to account for plasticity in quasi-brittle materials. As a result, the effective moduli model can be applied to a larger range of materials. The effective moduli constitutive model is used to simulate beryllium flyer plate experiments. The results from the continuum scale simulations using statistics from a single high-fidelity simulation are found to be in excellent agreement with numerical and experimental velocity interferometer data. The same set of crack statistics are used to extrapolate the results of a higher rate flyer plate case using the effective moduli model. In conclusion, the extension of this model to higher rate cases shows promise for further reducing the number of costly high-fidelity simulations needed to generate crack statistics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Assessment Approach to Advanced Fuel Models

This document constitutes completion of the NEAMS milestone M3MS-21IN0201016, which is titled: Assessment of advanced fuel improvements. In this report we present: (1) simulations of separate effects creep tests for uranium alloy and HT-9; (2) examples of standardizing and updating metallic fuel assessments to include the latest models and key output figures of merit, which is coordinated with LANL to better evaluate advanced models; (3) examples of how the FIPD database at ANL is integrated into metallic fuel assessment cases; and finally (4) documentation of fuel-specific figures of merit and the BISON review process for assessments with best practices for preparing and reviewing finite element simulations in the appendix.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A Simple, Scalable Large Deformation Solid Mechanics Implementation in the MOOSE Framework

This article describes a large deformation solid mechanics solver implemented as part of the freely available and open source MOOSE finite element simulation framework. The article documents the choices made in developing the solid mechanics framework and describes novel formulations for the gradient operator and constitutive modeling framework made to simplify implementations of different coordinate systems, stabilized gradient operators, and different constitutive model inputs and outputs. In the process, the article describes a new formulation that casts objective integration of the Cauchy stress as a linear transformation of the small stress rate. Finally, the article presents key implementation details and examines the parallel efficiency of the solid mechanics solver implemented in MOOSE. The implementation retains a good weak scaling efficiency beyond 1,000 parallel processes. The article includes a discussion of the factors limiting the parallel efficiency of implicit, large deformation solid mechanics codes on current high-performance computers, with the main current limitation being the scalability of the algebraic multigrid methods used to solve the linearized equilibrium equations.

Applied computing → Computer-aided design↗
DOE OSTI2020

Utah FORGE: Phase 3 Magnetotelluric (MT) Data

New high-quality tensor MT data at 122 sites, including the vertical magnetic field and utilizing ultra-remote referencing, have been acquired over the Utah FORGE project area. The results will be used to delineate the densities of faults and fractures in crystalline basement rocks, to define the heat sources, and to derive baseline 3D resistivity structure for later MT monitoring of temporal changes in resistivity structure following well stimulation in the EGS reservoir. There are three files here related to Utah FORGE magnetotelluric (MT) data acquisition and processing. The FORGE MT EDIs zip file contains the observed MT responses in industry-standard EDI format. For each site, there is an EDI response file that utilized a local independent reference for noise cancellation, and a file that utilized a distant reference cancelling noise associated with the DC transmission line of the Delta IPP passing down the west side of Milford Valley. These two site files could be merged as appropriate. The FORGE Model Cell Center file contains the model volume of the 3D Forge MT inversion for characterizing the resistivity structure in the project area. It was derived using finite element inversion methodology described in Wannamaker et al, in the attached FORGE Phase3 Geophysics paper, from the MT observation EDI files. It is ASCII format (.dat) and entries are defined at top of the file in a simple x-y-z-Rho listing in UTM coordinates. The element layers drape the topography so the Rho value layers are not purely horizontal slices. This greatly simplifies the listing.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

High-Order Hybrid RANS-LES Study of NACA0012 Wing Sections

We develop hybrid RANS-LES strategies within Nek5000 for application to airfoil sections at small flight configurations. We present a validation and verification study of $k \space – \space \tau$ SST applied to a NACA 0012 wing section in a pure RANS and in a hybrid RANS-LES setup. The study shows good corroboration with existing experimental and numerical datasets. We also analyze some of the observed discrepancies with the experiments by evaluating the side wall “blocking” effect. We demonstrate that for the hybrid turbulence modeling approach a high-order spectral- element discretization converges faster (i.e., with less resolution) than a representative low-order finite-volume-based approach.

42 ENGINEERING↗
DOE OSTI2025

A Finite Element Study of Stress Reduction Techniques in REBCO HTS Conductor on a Round Cable (CORC) Cable

ReBCO high-temperature superconducting (HTS) tape is critical for achieving the high magnetic fields needed in next-generation particle accelerators. Enhancing the mechanical performance of ReBCO tape increases its critical current by reducing internal stress, especially in the superconducting layer. A finite element study examined how copper layer properties affect stress in ReBCO conductor on a round core (CORC) cables. The cable was modeled as a doubly supported beam under uniform compressive stresses."cable was modeled as a doubly supported beam under uniform load to simulate bending. A staged modeling approach from a single tape to a six-layer stack enabled validation and efficient parameter studies. Increasing the yield strength and Young s modulus of the copper layers reduced peak stress in the ReBCO layer. These results support development of improved tape stacks for high-field accelerator magnets

Mueller, Scott [Northern Illinois U.]↗
DOE OSTI2020

NRC Multiphysics Analysis Capability Deployment FY2020: Part 3

This report details progress and activities of Idaho National Laboratory (INL) on the Nuclear Regulatory Commission (NRC) project “Development and Modeling Sup- port for Advanced Non-Light Water Reactors.” The tasks completed for this report are: Task2c: Explicit modeling of pebble transient temperature response. In this simulation, the 400 MWth Pebble-Bed Modular Reactor (PBMR) design, PBMR- 400, experiences a 20-second power ramp from 100% to 150% power. This is followed by a similar reduction in the power back to 100%. Several multiscale pebble coupling approaches are tested with one pebble per mesh element in the active core region. The results show good conservation behavior and the stability of the coupling.; Extended scope part 1: An assessment of the computational efficiency of the Discontinuous Finite Element Method (DFEM) heat transfer solver shows good scalability. The DFEM solver is a factor of 4 more expensive in solution time than the Finite Element Method (FEM) solver for heat transfer problems due to the increased number of degrees of freedom. Nonetheless, the DFEM approach provides the user with the flexibility to model gap heat transfer problems.; Extended scope part 2: The GapHeatTransferInterfaceMaterial was improved to give the user increased flexibility with the modeling of heat transfer through gaps with the DFEM solver. A number of gap parameters can now be coupled both through functions and variables.; Extended scope part 3: Demonstration of how the gap width between hexagonal fuel cells can be calculated during a heat-up transient and used in the GapHeatTransferInterface model. A full-domain DFEM model with gap expansion is coupled to a SubApp that models the thermal expansion of the base plate. The results show the expected physical behavior, although have not been fully bench-marked at this point in time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Interface capturing simulations of bubble population effects in PWR subchannels

As the computational power of high-performance computing (HPC) facilities grows, so too does the feasibility of using first principle based simulation to study turbulent two-phase flows within complex pressurized water reactor (PWR) geometries. Direct numerical simulation (DNS), integrated with an interface capturing method, allows for the collection of high-fidelity numerical data using advanced analysis techniques. The research presented here employs the massively parallel, finite-element based, unstructured mesh code, PHASTA, to simulate a set of two-phase bubbly flows through PWR subchannel geometries including auxiliary structures (spacer grids and mixing vanes). The main objective of the presented work is to analyze bubble dynamics and turbulence interactions at varying bubble concentrations to support the development of advanced two-phase flow closure models. Turbulent two-phase flows in PWR subchannels were simulated at hydraulic Reynolds numbers of 81,000 with bubble concentrations of 3%–15% by gas volume fraction (768–3928 resolved bubbles, respectively) and compared against a 1% void fraction case (262 bubbles) that had been previously simulated. The finite element mesh utilized for the study at higher bubble concentrations was composed of 1.55 billion elements, compared to the previous study which employed 1.11 billion elements, ensuring all turbulence scales and individual bubbles within the flow are fully resolved. For each case, the resolved initial bubble size was 0.65 mm in diameter (resolved with 25 grid points across the diameter). The simulations were analyzed to find flow features such as the mean velocity profile, bubble relative velocity and the effect of the bubbles on the turbulent conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

TRITIUM TRANSPORT MODELING AT THE PORE SCALE IN CERAMIC BEEDER MATERIALS USING TMAP8

Fusion reactors depend on the blanket material to breed and release tritium at the same rate or faster than it is consumed by the fusion reaction. Cellular ceramic breeders are dense materials that can maintain a high tritium breeding ratio while promoting tritium release thanks to highly connected pores. Assessing the tritium breeding capabilities of these materials requires a combination of extensive experimental and modeling efforts. In this work, we develop and calibrate a multiphysics model of tritium transport. This novel model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. We perform a sensitivity analysis and calibrate the model by comparing its predictions against experimental measurements of deuterium absorption. The calibrated model is then used to model tritium absorption in samples with different pore microstructures to investigate the effect of pore interconnectivity on tritium absorption. The model is part of the development of the multiscale, multiphysics framework for tritium transport (i.e., the Tritium Migration Analysis Program [TMAP8]), which is itself built on top of the finite element multiphysics framework MOOSE. This study demonstrates some of TMAP8’s capabilities, and is the first step toward assessing the tritium breeding capabilities of ceramic breeder material designs.

08 HYDROGEN↗
DOE OSTI2020

Thermo-mechanical modeling and experimental validation for multilayered metallic microstructures

This paper presents thermo-mechanical modeling on multilayered metallic microstructures consisting of two bilayers that enable 3D deployment once being Joule heated. Additionally, a representative design of such microstructures, as well as their working principle is introduced. Furthermore, a mathematical model is derived using Euler–Bernoulli beam theory, and analytical solutions describing out-of-plane displacement of the multilayered microstructures when uniformly heated, which is validated by finite element analysis. Parametric analysis on thermal load and dimensional change of beam shows a good agreement between the analytical solutions and results given by finite element analysis. The phases of the near-equiatomic NiTi layer are analyzed by EDS and XRD, which prove to be austenite during the Joule heating process. The mechanical properties of austenite NiTi are incorporated into the analytical solutions that provides a good estimation of 3D deployment of microstructures made of NiTi and aluminum. The experimental results provide an approximately 7 µm out-of-plane deployment by applying a uniform temperature increase of 132 K, and parametric analysis on the dimension of top aluminum beam offers another promising approach to larger 3D deployment. The proposed mathematical model provides an efficient tool for predicting the out-of-plane deployment of such multilayered microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A reinvestigation into Munson’s model for room closure in bedded rock salt

Accurate predictions of room closure are important for hazardous waste repositories in rock salt formations, such as the Waste Isolation Pilot Plant (WIPP). When Munson and co-workers simulated several room closure experiments conducted at the WIPP during the 1980’s and 1990’s, their simulated closure curves closely agreed with the closure measurements. A careful review of their work, however, raised concerns and prompted the reinvestigation in this paper. Here, to begin the reinvestigation, Munson’s legacy Room D closure simulation was reasonably recreated in a current-day finite element code. Next, special care was taken to obtain numerically converged results, re-introduce the anhydrite strata intermittently ignored by Munson, and calibrate the Munson–Dawson (M–D) constitutive model for salt as much as possible from laboratory test measurements. When this new model was used to simulate Room D’s closure, it under-predicted the horizontal and vertical closure rates by 2.34x and 3.10x, respectively, at 5.7 years after room excavation. As a result, the M–D model was extended to capture the newly established creep behavior at low equivalent stresses (<8 MPa) and replace the Tresca with the Hosford equivalent stress. Simulations using the new M–D model over-predicted the horizontal closure rate by 1.15x and under-predicted the vertical closure rate by 1.08x at 5.7 years, averaged over three room closure experiments. Although further improvements could be made, the new model has a stronger scientific foundation than Munson’s legacy model and appears ready for careful engineering use.

58 GEOSCIENCES↗
DOE OSTI2020

A method for characterization of multiple dynamic constitutive parameters of FRCs

We propose a method to measure multiple dynamic material constitutive parameters of unidirectional fiber reinforced composites (FRCs) in a single experiment. Dynamic short-beam shear (DSBS) experiments were performed on a modified Kolsky compression bar, with integration of high-speed imaging and digital image correlation (DIC). The unidirectional FRCs investigated were S-2 glass fiber reinforced matrix of TGDDM-Jeffamine® D230 with monoamine functionalized partially reacted substructures (mPRS) and commercially available SC-15. Analytical solutions of normal and shear strains of a composite beam were derived based on Timoshenko beam theory, assuming material to be transversely isotropic and have different moduli in tension and compression in each principle material orientation. Tensile and compressive moduli were inversely computed through monitoring normal strain slope when specimen was constantly loaded at a speed of ~7.3 m/s within a small deflection. Non-linear shear stress-strain behavior of the composite was described via Ramberg–Osgood equation. Finite element (FE) analysis was conducted in ABAQUS, simultaneously defining via user subroutine UMAT the transverse isotropy of material, bi-modulus constitutive model, and non-linear shear stress-strain relation. The method proposed in this work was validated by comparing strain distributions computed by FE model and DIC measurements. Comparing with traditional dynamic tensile, compressive, and shear experiments on FRCs, this method significantly simplifies the specimen preparation and design of complicated gripping fixtures for multiple experiments. Here, systematic errors resulting from variations of specimen geometry and dimension, loading direction, and instrumentation are reduced, thereby providing compatible data for numerical studies on impact behavior of composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Striving to translate shale physics across ten orders of magnitude: What have we learned?

Shales will play an important role in the successful transition of energy from fossil-based resources to renewables in the coming decades. Aside from being a significant source of low-carbon intensity fuels, like natural gas, they also serve as geologic seals of subsurface formations that may be used to isolate nuclear waste, sequester CO 2 , or store intermittent energy (e.g., solar hydrogen). Despite their importance, shales pose significant engineering and environmental challenges due to their nanoporous structure and extreme heterogeneity that spans at least ~10 orders of magnitude in spatial scale. Two challenges inhibit a system-level understanding: (1) the physics of fluid flow and phase behavior in shales are poorly understood due to the dominant molecular interactions between minerals and fluids under confinement, and (2) the apparent lack of scale separation that prevents a reliable (closed) description of the physics at any single scale of observation. In this review, we focus on the latter issue and discuss scale translation, which in its broadest sense is transforming data or simulations from one spatiotemporal scale to another. While effective scale translation is not exclusive to shales, but all geologic porous media, the need for it is especially acute in shales given their high degree of heterogeneity. Classical theories like homogenization, while indispensable, fail when scales are not separated. Other methods, like numerical upscaling, scale-translate in only one direction: small to large, but not the reverse, called downscaling. However, the confluence of advances in three areas are bringing challenging problems such as shales within reach: increased computational power and scalable algorithms; high-resolution imaging and multi-modal data acquisition; and machine learning to process massive amounts of data. While these advances equip geoscientists with a wide array of experimental and computational tools, no individual tool can probe the entire gamut of heterogeneity in shales. Their effective use, therefore, requires an ability to bridge between various data types obtained at different scales. The aim of this review is to present a coherent account of computational and experimental methods that may be used to achieve just that, i.e., to perform scale translation. We provide a broader definition of scale translation, one that transcends classical homogenization and upscaling methods, but is consistent with them and accommodates notions like downscaling and data translation. After a brief introduction to homogenization, we review hybrid methods, numerical upscaling and its recent extensions, multiscale computing, high-resolution imaging, and machine learning. We place particular emphasis on multiscale computing and propose an algorithmic framework to bridge between the pore (micro) and Darcy (macro) scales. Throughout the paper, we draw comparisons between the various methods and highlight their (often hidden) similarities, differences, benefits, and pitfalls. We finally conclude with two case studies on shales that exemplify some of the methods presented.

58 GEOSCIENCES↗
DOE OSTI2020

Compensation of heat load deformations using adaptive optics for the ALS upgrade: a wave optics study

In this paper, a realistic wave optics simulation method has been developed to study how wavefront distortions originating from heat load deformations can be corrected using adaptive X-ray optics. Several planned soft X-ray and tender X-ray insertion-device beamlines in the Advanced Light Source upgrade rely on a common design principle. A flat, first mirror intercepts the white beam; vertical focusing is provided by a variable-line-space monochromator; and horizontal focusing comes from a single, pre-figured, adaptive mirror. A variety of scenarios to cope with thermal distortion in the first mirror are studied by finite-element analysis. The degradation of the intensity distribution at the focal plane is analyzed and the adaptive optics that correct it is modeled. The range of correctable wavefront errors across the operating range of the beamlines is reported in terms of mirror curvature and spatial frequencies. The software developed is a one-dimensional wavefront propagation package made available in the OASYS suite, an adaptable, customizable and efficient beamline modeling platform.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Tardigrade-examples V0.1.0

Tardigrade-examples is a repository of computational workflows that exercise the Tardigrade software package. The Tardigrade software package is an implementation of Eringen’s micromorphic continuum theory with capabilities to support multiscale material modeling. These capabilities include homogenization through the Micromorphic Filter, calibration of micromorphic material models, and macroscale simulation in Tardigrade-MOOSE. This repository investigates continuum upscaling of various direct numerical simulations (DNS) conducted in Abaqus finite element (FE), Ratel FE, and GEOS material point method (MPM) software. Verification of the upscaling workflow is first investigated by considering DNS of trivial stress states for homogeneous materials, results of which indicate that classical continuum behavior is recovered as expected. DNS of heterogeneous materials are then considered.

Allard, Thomas↗
DOE OSTI2025

Feasibility Assessment of Using Electrical Impedance Tomography for Damage Localization in Graphite Microreactor Components

Microreactors have great potential to decrease capital costs and construction timelines, reducing the barriers to implementing advanced nuclear reactor technologies. However, the lower power output of these microreactors introduces economic challenges if the operation and maintenance costs cannot be reduced sufficiently. Many microreactor concepts use graphite materials for in-core moderator and structural purposes, which will require periodic inspection or, ideally, in situ structural health monitoring. This work describes an initial evaluation of the feasibility of leveraging graphite’s semiconducting properties to perform electrical impedance tomography (EIT) for defect localization. First, a study was performed to identify the best methods for bonding electrical contacts to minimize the effects of contact resistance that interfere with impedance measurements of the graphite. After determining the best bonding approach, electrodes were attached to multiple graphite components with varying geometries (e.g., simple block and more representative microreactor hexagonal block). In parallel, finite element analysis approaches were developed and implemented to analyze the impact of defects and contact resistances and to inform an iterative inverse model for reconstructing the conductivity distribution. The results of this study show that defect localization in graphite components is possible using EIT if a sufficient number of electrodes (to improve spatial resolution) can be bonded using a technique with very low contact resistance and those contact resistances remain stable during reactor operation. If the reactor core and vessel design do not allow electrodes to be bonded during reactor operation, then it may be possible to detach/reattach electrodes between reactor operation and outages if a suitable mechanical connection that offers repeatable contact resistance can be identified. Alternatively, future work could focus on identifying contacts that can survive the harsh reactor operating environment so that contacts do not need to be removed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Frequency Domain Reflectometry (FDR) Simulation Techniques for Digital Twin Representation of an Electrical Cable

Simulation of cable system response to frequency domain reflectometry (FDR) tests can be instrumental to understanding these tests and the nature and influence of various cable anomalies on test signatures. Reflectometry simulations are based upon a finite element representation of cable conductors and insulation to produce an S-parameter at each evaluated frequency. The aggregate collection of cable model S-parameters can simulate the influence on a test signal injected into a physical cable. Such an approach was undertaken in this work to produce a digital twin simulation of a low-voltage electrical cable. The electrical cable digital twin examined the influence of test simulation parameters and the relative influence of cable anomalies, including thermal aging, water or moisture exposure, water or moisture ingress, and other anomalies. The digital twin in this work included modeling of the conductors, insulation, jacket, and surrounding environment (air, water, etc.). The digital twin could be expanded to include cable bends, junctions and splices, branch or T systems, and termination impedances of motors or instruments. Observations and conclusions of this work include: 1. Fully 3D digital twin simulation of an electrical cable using an FDR approach is possible. However, there are tradeoffs between simulation fidelity and solution time, which must be balanced to ensure the simulation solves in an adequate amount of time (e.g., less than 20 minutes). Simulation parameters to balance include frequency bandwidth, number of frequencies, mesh density, connection impedance, and permittivity tolerance. 2. The digital twin simulation can explain FDR sensitivity to various cable anomalies, including entry and exit from an oven or water bath. 3. The digital twin simulation FDR response attenuates with distance along the cable and is further affected by the frequency bandwidth, which is similar to that observed with physical measurements. 4. The resolution of the digital twin FDR peaks increased with increasing bandwidth and with increasing number of frequencies, again similar to physical measurements. 5. The presence of multiple anomalies in the digital twin does not substantially attenuate the FDR response to anomalies located beyond the first encountered anomaly and impedance mismatch. 6. Spectral variation of the permittivity did not have a significant effect on the FDR response compared to a fixed nominal value. 7. Extension of the digital twin to 1000 ft still allowed for detection of distal anomalies near the far end of the electrical cable from the instrument connection point. 8. The ARENA test bed facilitates efficient NDE evaluations of well understood cable anomalies with various NDE methods without risking actual plant damage.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Efficient Reformulation of Linear and Nonlinear Solid-Phase Diffusion in Lithium-ion Battery Models using Symmetric Polynomials: Mass Conservation and Computational Efficiency

Lithium-ion batteries are typically modeled using porous electrode theory coupled with various transport and reaction mechanisms, along with suitable discretization or approximations for the solid-phase diffusion equation. The solid-phase diffusion equation represents the main computational burden for typical pseudo-2-dimensional (p2D) models since these equations in the pseudo r -dimension must be solved at each point in the computational grid. This substantially increases the complexity of the model as well as the computational time. Traditional approaches towards simplifying solid-phase diffusion possess certain significant limitations, especially in modeling emerging electrode materials which involve phase changes and variable diffusivities. A computationally efficient representation for solid-phase diffusion is discussed in this paper based on symmetric polynomials using Orthogonal Collocation and Galerkin formulation (weak form). A systematic approach is provided to increase the accuracy of the approximation (p form in finite element methods) to enable efficient simulation with a minimal number of semi-discretized equations, ensuring mass conservation even for non-linear diffusion problems involving variable diffusivities. These methods are then demonstrated by incorporation into the full p2D model, illustrating their advantages in simulating high C-rates and short-time dynamic operation of Lithium-ion batteries.

25 ENERGY STORAGE↗