Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Airframe/propulsion integration characteristics at transonic speeds

The aerodynamic characteristics for both single and twin-engine high-performance aircraft are significantly affected by shock induced flow interactions as well as other local flow interference effects which usually occur at transonic speeds. These adverse interactions can not only cause high drag, but also cause unusual aerodynamic loadings and/or severe stability and control problems. Many programs are under way to not only develop method for reducing the adverse effects, but also to develop an understanding of the basic flow conditions which are the primary contributors. It is anticipated that these programs will result in technologies which can reduce the aircraft cruise drag through improved integration as well as increase aircraft maneuverability through the application of thrust vectoring. Some of the primary integration problems for twin-engine aircraft at transonic speeds are identified, and several methods are demonstrated for reducing or eliminating the undersirable characteristics, while enhancing configuration effectiveness.

Henderson, William P.↗
NASA NTRS1989

Fracture characteristics of balloon films

An attempt was made to determine the failure modes of high altitude scientific balloons through an investigation of the fracture characteristics of the thin polyethylene films. Two films were the subject of the evaluation, Winzen Int.'s Stratafilm SF-85 and Raven Industries' Astro-E. Research began with an investigation of the film's cold brittleness point and it's effect on the ultimate strength and elasticity of the polyethylene film. A series of preliminary investigations were conducted to develop an understanding of the material characteristics. The primary focus of this investigation was on the notch sensitivity of the films. Simple stress strain tests were also conducted to enable analysis employing fracture toughness parameters. Studies were conducted on both film types at 23 C (room temperature), -60 C, -90 C, and -120 C.

Portanova, Marc A.↗
NASA NTRS1988

AVIRIS data characteristics and their effects on spectral discrimination of rocks exposed in the Drum Mountains, Utah: Results of a preliminary study

Airborne Visible and Infrared Imaging Spectrometer (AVIRIS) data collected over a geologically diverse field site and over a nearby calibration site were analyzed and interpreted in efforts to document radiometric and geometric characteristics of AVIRIS, quantify and correct for detrimental sensor phenomena, and evaluate the utility of AVIRIS data for discriminating rock types and identifying their constituent mineralogy. AVIRIS data acquired for these studies exhibit a variety of detrimental artifacts and have lower signal-to-noise ratios than expected in the longer wavelength bands. Artifacts are both inherent in the image data and introduced during ground processing, but most may be corrected by appropriate processing techniques. Poor signal-to-noise characteristics of this AVIRIS data set limited the usefulness of the data for lithologic discrimination and mineral identification. Various data calibration techniques, based on field-acquired spectral measurements, were applied to the AVIRIS data. Major absorption features of hydroxyl-bearing minerals were resolved in the spectra of the calibrated AVIRIS data, and the presence of hydroxyl-bearing minerals at the corresponding ground locations was confirmed by field data.

Bailey, G. B.↗
NASA NTRS1989

Transonic aerodynamic characteristics of a proposed Assured Crew Return Capability (ACRC) lifting-body configuration

The investigation was conducted in the Calspan 8-Ft Transonic wind tunnel at Mach numbers from 0.6 to 1.2. The 0.07-scale model had a low aspect ratio body with a flat undersurface. A center fin and two tip fins were mounted on the aft upper body. The tip fins were rolled outboard 40 deg from the vertical. Elevon surfaces made up the trailing edges of the outboard fins and body flaps were located on the upper and lower aft fuselage. Results of the investigation indicated that the model was longitudinally and laterally stable about a center-of-gravity position of 0.54 body length. The maximum trimmed lift-drag ratio was about 3.1 at M = 0.6. The small center fin contributed only a small positive increment to lateral stability but was effective as a yaw control device. Protuberances on the forebody had little effect on the aerodynamic characteristics of the configuration. The model with pitch controls undeflected had desirable longitudinal trim characteristics.

Ware, George M.↗
NASA NTRS1989

Wind-tunnel investigation of aerodynamic characteristics and wing pressure distributions of an airplane with variable-sweep wings modified for laminar flow

A wind tunnel test was conducted to evaluate the aerodynamic characteristics and wing pressure distributions of a variable wing sweep aircraft having wing panels that are modified to promote laminar flow. The modified wing section shapes were incorporated over most of the exposed outer wing panel span and were obtained by extending the leading edge and adding thickness to the existing wing upper surface forward of 60 percent chord. Two different wing configurations, one each for Mach numbers 0.7 and 0.8, were tested on the model simultaneously, with one wing configuration on the left side and the other on the right. The tests were conducted at Mach numbers 0.20 to 0.90 for wing sweep angles of 20, 25, 30, and 35 degrees. Longitudinal, lateral and directional aerodynamic characteristics of the modified and baseline configurations, and selected pressure distributions for the modified configurations, are presented in graphical form without analysis. A tabulation of the pressure data for the modified configuration is available as microfiche.

Hallissy, James B.↗
NASA NTRS1988

Flight-test determination of aircraft cruise characteristics using acceleration and deceleration techniques

A flight-test technique has been developed under NASA Dryden sponsorship NSG 4028 to predict aircraft cruise performance characteristics. The technique used acceleration and deceleration maneuvers to define baseline aerodynamic and propulsion system characteristics, which were then input to a performance modeling prediction program. Conventional stabilized 'speed power' tests, which are normally used for cruise performance definition, can comprise a large portion of the flight time in a program. A significant reduction in flight time was estimated using the performance modeling approach with associated savings in cost and schedule. A 20-h verification flight-test program was accomplished.

Yechout, T. R.↗
NASA NTRS1988

Dynamic characteristics of a 20 kHz resonant power system - Fault identification and fault recovery

A detailed simulation of a dc inductor resonant driver and receiver is used to demonstrate the transient characteristics of a 20 kHz resonant power system during fault and overload conditions. The simulated system consists of a dc inductor resonant inverter (driver), a 50-meter transmission cable, and a dc inductor resonant receiver load. Of particular interest are the driver and receiver performance during fault and overload conditions and on the recovery characteristics following removal of the fault. The information gained from these studies sets the stage for further work in fault identification and autonomous power system control.

Wasynczuk, O.↗
NASA NTRS1988

Petrology of ALH85085 - A chondrite with unique characteristics

The characteristics of the chondrite ALH85085 are examined. It is found that the chondrules of ALH85085 are 25-75 microns in size. The majority of the chondrules are cryptocrystalline and all of them are volatile depleted. It is shown that the FeNi metal abundance is 40.9 wt pct and the sulfide abundance is 1.1 wt pct. The matrix lumps and bulk composition of ALH85085 are analyzed. The characteristics of ALH85085 are compared with other chondrite groups, showing that it cannot be classified. The possible origin of ALH85085 is analyzed, showing trends similar to those of calculated nebular condensation paths indicating a nebular origin.

Weisberg, Michael K.↗
NASA NTRS1989

Characteristics of the ground vortex formed by a jet moving over a fixed ground plane

This paper discusses an experimental study conducted in the Langley Vortex Facility to investigate the effects on the ground vortex of the jet passing over a fixed ground board. A jet impacting the ground can form a vortex which may materially affect the aerodynamic characteristics of a STOL airplane operating near the ground. Several studies have been done with a stationary jet exiting near and perpendicular to fixed ground board. The resulting ground effects have been documented in terms of ground vortex and aerodynamic characteristics. The ground boundary layer created in a wind tunnel facility, however is thought to affect the extent of the ground vortex. This paper reports on an investigation utilizing an isolated moving jet to eliminate the ground boundary layer. The results are compared to the existing data base and show a 30 percent decrease in the vortex penetration shown by the stationary jet conditions.

Kemmerly, G. T.↗
NASA NTRS1989

Prop-fan airfoil icing characteristics

An icing test program was carried out during the 1986-87 and 1987-88 icing seasons at the Fluidyne Icing Tunnel. The testing consisted of evaluating the icing characteristics and aerodynamic performance characteristics of two thin, two-dimensional airfoil sections. The two airfoils were a NACA Series 16-203 and a Hamilton Standard PF1-304, 3 and 4 percent thickness-to-chord ratio airfoils, respectively. These airfoils are representative of the thin airfoils currently being evaluated for Prop-Fan propulsion systems. The tests were conducted over a wide range of icing conditions, angles-of-attack, and Mach numbers (0.3 to 0.8).

Pike, J. A.↗
NASA NTRS1988

Fore-and-aft stiffness and damping characteristics of 30 x 11.5-14.5, Type VIII, bias-ply and radial-belted aircraft tires

Measurements of footprint geometrical properties and fore and aft stiffness and damping characteristics were obtained on 30 x 11.5-14.5 bias-ply and radial-belted aircraft tires. Significant differences in stiffness and damping characteristics were found between the two design types. The results show that footprint aspect ratio effects may interfere with the improved hydroplaning potential associated with the radial-belted tire operating at higher inflation pressures.

Lopez, Mercedes C.↗
NASA NTRS1988

Performance characteristics of a new helical-channel microchannel plate

An advanced version of the 'helical-channel' microchannel plate (MCP) is presented. This MCP is composed of four channels per fiber with each channel having a diameter of 50 microns. The dynamic range, pulse-height distribution, and gain characteristics of this MCP are discussed. It is found that increasing the twist density of the channels makes it possible to increase the detection efficiency and further improve the suppression of ion-feedback providing a tighter saturated pulse-height distribution and improved high-voltage characteristics.

Slater, David C.↗
NASA NTRS1989

Some low-speed flutter characteristics of simple low-aspect-ratio delta wing models

Some results from a combined experimental and analytical study of the low-speed flutter characteristics of low-aspect-ratio delta wings are presented. Data are presented which show the effects of sweep angle on the flutter characteristics of some simple plate models of constant planform area. The range of sweep angles studied was from 30 to 72 degrees. In addition, flutter results are presented for two 30 deg-sweep clipped-delta wing models. Further results are presented that show the effects of root clamping (percentage length of the root chord that is cantilevered) for a 45 deg-sweep delta wing. The experimental data are compared with analytical results obtained by using kernel function and doublet lattice subsonic unsteady lifting surface theories.

Doggett, Robert V., Jr.↗
NASA NTRS1989

Phase and amplitude characteristics of InP:Fe modified interdigitated gap photoconductive microwave switches

The transmission amplitude and phase characteristics of InP:Fe modified interdigitated gap photoconductive microwave switches are reported. Measurements in the 0.1-1 GHz frequency range show that the phase is shifted about 90 deg and that the corresponding change in amplitude ranges from 43 dB at 0.1 GHz to 23 dB at 1 GHz when the illumination-induced conductance is switched from a low OFF-state value (aboit 4 x 10 to the -8 S) to a high ON-state value (5 mS). The observed characteristics can be described by a phase-shifting region and an amplitude modulation region. In the phase-shifting region the phase strongly depends on the conductance, and the amplitude is almost constant. In the amplitude modulation region both the amplitude and the phase depend on the conductance but the effect on the amplitude is much more pronounced. A lumped-element model describing the device performance is presented. It is concluded that these optoelectronic microwave switching devices are suitable for high-speed amplitude modulation but are not promising as high-speed phase shifters.

Andersson, Ingmar L.↗
NASA NTRS1989

Installed propfan (SR-7L) far-field noise characteristics

Far-field noise characteristics of the SR-7L single-rotor propfan were obtained from the Propfan Test Assessment (PTA) aircraft flight tests. The aircraft was flown at low altitudes (about 310m) above the ground at a constant speed of about 92 m/sec. The acoustic data were acquired with an array of ground-flush microphones positioned on both sides of the flight path. Propfan-generated noise levels were extracted from the total aircraft noise, and these data were then used to study the far-field noise characteristics. The directivities at the polar and azimuthal planes, and the variations of the blade-order tone levels with propfan power and blade tip Mach number were derived. The effect of inflow angle was studied by changing the nacelle tilt angle. The levels and the directivity were very sensitive to the nacelle tilt angle (i.e., inflow angle). The noise levels in the aft quadrant were found to be higher than in the forward quadrant. Also, the noise levels on the starboard side of the aircraft were found to be higher than on the port side. The noise levels increase with propfan power and rotational speed.

Reddy, N. N.↗
NASA NTRS1989

Characteristic-eddy decomposition of turbulence in a channel

Lumley's proper orthogonal decomposition technique is applied to the turbulent flow in a channel. Coherent structures are extracted by decomposing the velocity field into characteristic eddies with random coefficients. A generalization of the shot-noise expansion is used to determine the characteristic eddies in homogeneous spatial directions. Three different techniques are used to determine the phases of the Fourier coefficients in the expansion: (1) one based on the bispectrum, (2) a spatial compactness requirement, and (3) a functional continuity argument. Similar results are found from each of these techniques.

Moin, Parviz↗
NASA NTRS1989

Measuring and modeling spectral characteristics of a tallgrass prairie

This study was conducted to evaluate the diurnal and seasonal, spectral reflectance characteristics of burned and unburned areas of a tallgrass prairie, based on field measurements and models of radiation transport in plant canopies. Burning of the senescent vegetation, resulting from the previous years' growth, is a common management practice, which results in improved productivity and affects the succession of grass species. The burned and unburned grass canopies showed distinctly different, diurnal and seasonal, spectral reflectance characteristics in the visible and infrared regions of the spectrum. These were attributed to the differences in development of the two plant canopies and the azimuthal differences in sensor-sun-canopy positions during field measurements of spectral reflectance. The radiation transfer model properly simulated the diurnal spectral behavior of the two canopies. The simulated, seasonal, spectral reflectance values for the unburned grass canopy were greater than the measured ones, because of limitations in proper representation of the layer of senescent vegetation in the model.

Asrar, G.↗
NASA NTRS1988

Cavitation characteristics of a small centrifugal pump in He I and He II

The cavitation characteristics of a small preinduced centrifugal pump operating in He I and He II over the temperature range 1.8-4.2 K are presented. The pump and close-coupled induction motor operate immersed in liquid helium. A six-blade propeller inducer and a three-blade screw inducer were both tested. With this pump configuration using either inducer, there is a tremendous difference between the cavitation characteristics of He I and He II. The net positive suction head requirements for this pump with the screw inducer could not be determined for He I, but it is less than -100 mm and, depending on flow rate, ranges between 35 and 165 mm for He II.

Ludtke, P. R.↗