SEARCH · Engineering Papers

Results for “Certification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Liquid water content and droplet size calibration of the NASA Lewis Icing Research Tunnel

The icing research tunnel at the NASA Lewis Research Center underwent a major rehabilitation in 1986 to 1987, necessitating recalibration of the icing cloud. The methods used in the recalibration, including the procedure used to establish a uniform icing cloud and the use of a standard icing blade technique for measurement of liquid water content are described. PMS Forward Scattering Spectrometer and Optical Array probes were used for measurement of droplet size. Examples of droplet size distributions are shown for several median volumetric diameters. Finally, the liquid water content/droplet size operating envelopes of the icing tunnel are shown for a range of airspeeds and are compared to the FAA icing certification criteria.

Ide, Robert F.↗

NASA NTRS1990

Relative merits of reactive and forward-look detection for wind-shear encounters during landing approach for various microburst escape strategies

The goal was to quantify the benefits of airborne forward-look windshear detection and to develop and test a candidate set of strategies for recovery from inadvertent microburst encounters during the landing approach, given the utilization of both reactive-only and forward-look windshear detection. Candidate strategies were developed and evaluated using a non-piloted simulation consisting of a simple point-mass performance model of a transport-category airplane flying through an analytical microburst model. The results indicate that the factor which most strongly effects a microburst recovery is the time at which the recovery is initiated. Forward-look alerts given 10 seconds prior to microburst entry permitted recoveries to be made with negligible altitude loss. The results also show that no single microburst scenario can be used to evaluate the relative merits of various recovery strategies. The type of alert used to initiate the recovery (reactive or forward-look) and the altitude of the microburst encounter had an effect on the type of recovery strategy that performed best. These factors may have serious implications for the design and certification of windshear systems.

Hinton, David A.↗

NASA NTRS1990

Software verification plan for GCS

This verification plan is written as part of an experiment designed to study the fundamental characteristics of the software failure process. The experiment will be conducted using several implementations of software that were produced according to industry-standard guidelines, namely the Radio Technical Commission for Aeronautics RTCA/DO-178A guidelines, Software Consideration in Airborne Systems and Equipment Certification, for the development of flight software. This plan fulfills the DO-178A requirements for providing instructions on the testing of each implementation of software. The plan details the verification activities to be performed at each phase in the development process, contains a step by step description of the testing procedures, and discusses all of the tools used throughout the verification process.

Dent, Leslie A.↗

NASA NTRS1990

Sole means navigation and integrity through hybrid Loran-C and NAVSTAR GPS

A sole means navigation system does not only call for integrity, but also for coverage, reliability, availability and accuracy. Even though ground monitored GPS will provide integrity, availability is still not sufficient. One satellite outage can affect a large service area for several hours per day. The same holds for differential GPS; a total satellite outage cannot be corrected for. To obtain sufficient coverage, extra measurements are needed, either in the form of extra GPS satellites (expensive) or through redundant measurements from other systems. LORAN-C is available and will, hybridized with GPS, result in a system that has the potential to satisfy the requirements for a sole means navigation system for use in the continental United States. Assumptions are made about the qualification sole means, mainly based on current sole means systems such as VOR/DME. In order to allow for system design that will satisfy sole means requirements, it is recommended that a definition of a sole means navigation system be established. This definition must include requirements for availability, reliability, and integrity currently not specified. In addition to the definition of a sole means navigation system, certification requirements must be established for hybrid navigation systems. This will allow for design and production of a new generation of airborne navigation systems that will reduce overall system costs and simplify training procedures.

Vangraas, Frank↗

NASA NTRS1990

An experimental evaluation of software redundancy as a strategy for improving reliability

The strategy of using multiple versions of independently developed software as a means to tolerate residual software design faults is suggested by the success of hardware redundancy for tolerating hardware failures. Although, as generally accepted, the independence of hardware failures resulting from physical wearout can lead to substantial increases in reliability for redundant hardware structures, a similar conclusion is not immediate for software. The degree to which design faults are manifested as independent failures determines the effectiveness of redundancy as a method for improving software reliability. Interest in multi-version software centers on whether it provides an adequate measure of increased reliability to warrant its use in critical applications. The effectiveness of multi-version software is studied by comparing estimates of the failure probabilities of these systems with the failure probabilities of single versions. The estimates are obtained under a model of dependent failures and compared with estimates obtained when failures are assumed to be independent. The experimental results are based on twenty versions of an aerospace application developed and certified by sixty programmers from four universities. Descriptions of the application, development and certification processes, and operational evaluation are given together with an analysis of the twenty versions.

Eckhardt, Dave E., Jr.↗

NASA NTRS1990

Ground-simulation investigations of VTOL airworthiness criteria for terminal-area operations

Several ground-based simulation experiments undertaken to investigate concerns related to tilt-rotor aircraft airworthiness were conducted. The experiments were conducted on the National Aeronautics and Space Administration (NASA) Ames Research Center's Vertical Motion Simulator, which permits simulation of a wide variety of aircraft with a high degree of fidelity of motion cueing. Variations in conversion/deceleration profile, type of augmentation or automation, level of display assistance, and meteorological conditions were considered in the course of the experiments. Certification pilots from the Federal Aviation Administration (FAA) and the Civil Aviation Authority (CAA) participated, in addition to NASA research pilots. The setup of these experiments on the simulator is summarized, and some of the results highlighted.

Lebacqz, J. V.↗

NASA NTRS1989

Robotic sampling system for an unmanned Mars mission

A major robotics opportunity for NASA will be the Mars Rover/Sample Return Mission which could be launched as early as the 1990s. The exploratory portion of this mission will include two autonomous subsystems: the rover vehicle and a sample handling system. The sample handling system is the key to the process of collecting Martian soils. This system could include a core drill, a general-purpose manipulator, tools, containers, a return canister, certification hardware and a labeling system. Integrated into a functional package, the sample handling system is analogous to a complex robotic workcell. Discussed here are the different components of the system, their interfaces, forseeable problem areas and many options based on the scientific goals of the mission. The various interfaces in the sample handling process (component to component and handling system to rover) will be a major engineering effort. Two critical evaluation criteria that will be imposed on the system are flexibility and reliability. It needs to be flexible enough to adapt to different scenarios and environments and acquire the most desirable specimens for return to Earth. Scientists may decide to change the distribution and ratio of core samples to rock samples in the canister. The long distance and duration of this planetary mission places a reliability burden on the hardware. The communication time delay between Earth and Mars minimizes operator interaction (teleoperation, supervisory modes) with the sample handler. An intelligent system will be required to plan the actions, make sample choices, interpret sensor inputs, and query unknown surroundings. A combination of autonomous functions and supervised movements will be integrated into the sample handling system.

Chun, Wendell↗

NASA NTRS1989

A review and update of the NASA aircraft noise prediction program propeller analysis system

The National Aeronautics and Space Administration (NASA) Aircraft Noise Prediction Program (ANOPP) Propeller Analysis System (PAS) is a set of computational modules for predicting the aerodynamics, performance, and noise of propellers. The ANOPP PAS has the capability to predict noise levels for propeller aircraft certification and produce parametric scaling laws for the adjustment of measured data to reference conditions. A technical overview of the prediction techniques incorporated into the system is presented. The prediction system has been applied to predict the noise signature of a variety of propeller configurations including the effects of propeller angle of attack. A summary of these validation studies is discussed with emphasis being placed on the wind tunnel and flight test programs sponsored by the Federal Aviation Administration (FAA) for the Piper Cherokee Lance aircraft. A number of modifications and improvements have been made to the system and both DEC VAX and IBM-PC versions of the system have been added to the original CDC NOS version.

Golub, Robert A.↗

NASA NTRS1989

Investigations of modifications to improve the spin resistance of a high-wing, single-engine, light airplane

A general aviation aircraft with drooped leading edge modifications for improvement of lateral stability at high angles of attack has been flight tested in combination with a ventral fin which improves directional stability. The two modifications were assessed in light of spin-resistance criteria proposed for incorporation into FAA certification regulations. The configuration combining outboard wing leading-edge droop and a ventral fin yielded a substantial increase in spin resistance, but fell short of all requirements encompassed by the proposed spin-resistance criteria.

Manuel, G. S.↗

NASA NTRS1989

Pinpoint landing concepts for the Mars Rover Sample Return mission

From knowledge of hazards gained following Viking, several approaches are being pursued for making the Mars Rover Sample Return (MRSR) landing safer. With the pinpoint landing capability approach, a single landing site would be certified in advance of initiating the descent orbit, using pictures transmitted to earth from the orbiter. Onboard instruments would guide the lander to follow mapped terrain to the selected site. If navigation proves insufficiently accurate, a small number of scattered sites would be certified, and the lander would select the most accessible one in real time. Some early-site certification and navigation concepts are discussed. Some of the key problems to overcome include how to recognize hazards too small to be transmitted to earth, how to represent terrain features in the flight computer, how to overcome errors in inertial measurements during landing of over 12-hour duration, how to find the selected site in real time, and how to navigate to the selected site once it is found.

Klumpp, Allan R.↗

NASA NTRS1990

Liquid water content and droplet size calibration of the NASA Lewis Icing Research Tunnel

Ide, Robert F.↗

NASA NTRS1990

A methodology for evaluating the reliability and risk of structures under complex service environments

The theoretical basis and numerical implementation of NESSUS (Numerical Evaluation of Stochastic Structures Under Stress; Cruse et al., 1988), a computer code for probabilistic structural analyses of aerospace components, are described, with an emphasis on the use of NESSUS for reliability and risk assessment. Topics addressed include the structure of NESSUS, the material-properties model, computational procedures, probabilistic models of fatigue-crack initiation, risk/cost evaluation, fatigue-fracture analyses, and fatigue-crack propagation. Numerical results from typical applications are presented in extensive graphs and briefly characterized; the usefulness of NESSUS predictions for establishing inspection and retirement schedules and for component certification is indicated.

Shiao, Michael C.↗

NASA NTRS1989

Protoflight photovoltaic power module system-level tests in the Space Power Facility

Work Package Four, which includes the NASA-Lewis and Rocketdyne, has selected an approach for the Space Station Freedom Photovoltaic (PV) Power Module flight certification that combines system level qualification and acceptance testing in the thermal vacuum environment: the 'protoflight' vehicle approach. This approach maximizes ground test verification to assure system level performance and to minimize risk of on-orbit failures. The preliminary plans for system level thermal vacuum environmental testing of the protoflight PV Power Module in the NASA-Lewis Space Power Facility (SPF) are addressed. Details of the facility modifications to refurbish SPF, after 13 years of downtime, are briefly discussed. The results of an evaluation of the effectiveness of system level environmental testing in screening out incipient part and workmanship defects and unique failure modes are discussed. Preliminary test objectives, test hardware configurations, test support equipment, and operations, are presented.

Rivera, Juan C.↗

NASA NTRS1989

Progress toward the development of an airfoil icing analysis capability

The NASA-Lewis aircraft icing analysis program is composed of three major sub-programs. These sub-programs are ice accretion simulation, performance degradation evaluation, and ice protection system evaluation. These topics cover all areas of concern related to the simulation of aircraft icing and its consequences. The motivation for these activities is twofold, reduction of time and effort required in experimental programs and the ability to provide reliable information for aircraft certification in icing, over the complete range of environmental conditions. In addition to the analytical activities associated with development of these codes, several experimental programs are underway to provide verification information for existing codes. These experimental programs are also used to investigate the physical processes associated with ice accretion and removal for improvement of present analytical models. The NASA-Lewis icing analysis program is thus striving to provide a full range of analytical tools necessary for evaluation of the consequences of icing and of ice protection systems.

Potapczuk, Mark G.↗

NASA NTRS1990

National plan to enhance aviation safety through human factors improvements

The purpose of this section of the plan is to establish a development and implementation strategy plan for improving safety and efficiency in the Air Traffic Control (ATC) system. These improvements will be achieved through the proper applications of human factors considerations to the present and future systems. The program will have four basic goals: (1) prepare for the future system through proper hiring and training; (2) develop a controller work station team concept (managing human errors); (3) understand and address the human factors implications of negative system results; and (4) define the proper division of responsibilities and interactions between the human and the machine in ATC systems. This plan addresses six program elements which together address the overall purpose. The six program elements are: (1) determine principles of human-centered automation that will enhance aviation safety and the efficiency of the air traffic controller; (2) provide new and/or enhanced methods and techniques to measure, assess, and improve human performance in the ATC environment; (3) determine system needs and methods for information transfer between and within controller teams and between controller teams and the cockpit; (4) determine how new controller work station technology can optimally be applied and integrated to enhance safety and efficiency; (5) assess training needs and develop improved techniques and strategies for selection, training, and evaluation of controllers; and (6) develop standards, methods, and procedures for the certification and validation of human engineering in the design, testing, and implementation of any hardware or software system element which affects information flow to or from the human.

Foushee, Clay↗

NASA NTRS1990

Airborne Wind Shear Detection and Warning Systems. Second Combined Manufacturers' and Technologists' Conference, part 1

The Second Combined Manufacturers' and Technologists' Conference hosted jointly by NASA Langley (LaRC) and the Federal Aviation Administration (FAA) was held in Williamsburg, Virginia, on October 18 to 20, 1988. The purpose of the meeting was to transfer significant, ongoing results gained during the second year of the joint NASA/FAA Airborne Wind Shear Program to the technical industry and to pose problems of current concern to the combined group. It also provided a forum for manufacturers to review forward-look technology concepts and for technologists to gain an understanding of the problems encountered by the manufacturers during the development of airborne equipment and the FAA certification requirements.

Spady, Amos A., Jr.↗

NASA NTRS1990

Airborne Wind Shear Detection and Warning Systems. Second Combined Manufacturers' and Technologists' Conference, part 2

The Second Combined Manufacturers' and Technologists' Conference was hosted jointly by NASA Langley (LaRC) and the Federal Aviation Administration (FAA) in Williamsburg, Virginia, on October 18 to 20, 1988. The meeting was co-chaired by Dr. Roland Bowles of LaRC and Herbrt Schlickenmaier of the FAA. The purpose of the meeting was to transfer significant, ongoing results gained during the second year of the joint NASA/FAA Airborne Wind Shear Program to the technical industry and to pose problems of current concern to the combined group. It also provided a forum for manufacturers to review forward-look technology concepts and for technologists to gain an understanding of the problems encountered by the manufacturers during the development of airborne equipment and the FAA certification requirements.

Spady, Amos A., Jr.↗

NASA NTRS1990

Summary of JAYGO mixing and FSM-1 application of castable inhibitor and liner

Two JAYGO planetary mixers (12 and 42 gallon) are being qualified to mix STW5-3224 liner and STW5-3223 castable inhibitor. These mixers are an integral part of a mix process which allows for safe addition of the asbestos component. An essential part of the engineering evaluation (ETP-0347) of these mixers is the generation of static test fire data. Ultimately, these results will help confirm the adequacy of these mixers for production mixing of liner and inhibitor. (These data are not required for qualification of the Certification Test Plan CTP-0125). The details on the mixing, inhibiting, and sling-lining of JAYGO-mixed castable inhibitor and liner which were applied to the FSM-1 segments are presented. The objectives are the following: (1) to document processing events surrounding the JAYO mixing of castable inhibitor and liner, and the subsequent inhibiting and sling lining onto the FSM-1 segments; and (2) to substantiate the measured properties of these JAYGO-mixed materials (rheological and mechanical) and compare these properties to existing production database.

Evans, Kurt B.↗