Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ceramic materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

First-principles study of the surface properties of LiAl 5 O 8 : Stability and tritiated water formation

LiAl 5 O 8 is an important secondary phase of γ-LiAlO 2 ceramics in tritium ( 3 H, T)-producing burnable absorber rods (TPBARs), present in small quantities in the as-fabricated condition and in larger quantities after irradiation due to Li burnup and mobility in the radiation-damaged lattice. In this work, we performed first-principles calculations to study the stabilities and structures of LiAl 5 O 8 surfaces the possibility of T 2 O formation on the (111) surface. By calculating the surface energies of all possible symmetrical stoichiometric and nonstoichiometric low-index surfaces, we identified the two most stable surfaces, one stoichiometric (001) surface and one nonstoichiometric (111) surface in an O-rich condition. The surface oxygen atoms on the nonstoichiometric (111) surface have remarkable displacements after relaxation, due to the large dangling O bonds. Considering a Li-poor and 3 H-rich condition relevant to TPBARs, we further studied these two stable surfaces with 37.5%, 75%, and 100% surface O atoms covered by 3 H atoms. Our results show that the 3H saturation is favorable for the nonstoichiometric (111) surface but not for the stoichiometric (001) surface. In addition, the structure of nonstoichiometric (111) surface is well stabilized when the surface O atoms are 100% saturated by 3 H atoms. Based on the fully 3H-saturated (111) surface, the 3 H 2 O desorption with an energy barrier of 0.69 eV is preferable in the 3 H-rich condition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tape casting and characterizations of MgO ceramics

Herein we report a high density MgO ceramic substrate produced by the tape casting technology. The tape casting formulation and process produced a uniform tape free of cracking. Y 2 O 3 and SiO 2 were used as the sintering aid for the pressureless sintering of the green tape. X-ray diffraction phase identification indicates that MgO is the main phase, while both Y 2 O 3 and SiO 2 sintering aids react with MgO to form MgY 4 Si 3 O 13 as the second phase. Liquid phase sintering occurs in the temperature range from 1030°C to ~1500°C, which is confirmed by the simultaneous Thermal Gravitation Analysis/ Differential Scanning Calorimeter (TGA/DSC) and the percent linear shrinkage and densification. A 96.5% theoretical density was achieved by presureless sintering at 1650°C for 2 hours, which was further increased to a fully dense structure using hotisostatic- pressing(HIP) at 1650°C and 207 MPa in argon. Scanning electron microscopy (SEM) and energy dispersive(EDS) spectroscopic analysis on the HIP’ed sample show that MgY 4 Si 3 O 13 is located at the MgO grain boundary and the sample has a fully dense structure. The refractive indices and extinction coefficient were measured on the HIP’ed sample along with thermal properties and dielectric properties. Thermal diffusivity and heat capacity were measured to calculate the thermal conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Grain boundary energy control in zinc aluminate nanoceramics

This study investigates the grain boundary energy dependence on segregated dopants in nanocrystalline zinc aluminate ceramics. Atomistic simulations of Σ3 and Σ9 grain boundaries showed that trivalent ions of varying ionic radii [Sc 3+ (74.5 pm), In 3+ (80.0 pm), Y 3+ (90.0 pm), and Nd 3+ (98.3 pm)] have a tendency to segregate to both interfaces, with Y 3+ presenting the highest segregation potentials. The connection between segregation and the reduction of interfacial energies was explored by measuring the grain boundary energy on nanoceramics fabricated via high‐pressure spark plasma sintering (HP‐SPS) using differential scanning calorimetry (DSC). The results revealed that Y 3+ doping at 0.5 mol% reduces the grain boundary energy in zinc aluminate nanoceramics from 1.1–1.3 J/m 2 to 0.6–0.8 J/m 2 ; the range correlates with the observed size dependence of the excess energy, with higher values observed for the smaller grain sizes (∼17 nm). The noted decrease in interfacial energies for doped samples suggests it is indeed possible to alter the stability of zinc aluminate grain boundaries via dopant segregation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural, vibrational, thermal, and magnetic properties of mullite-type NdMnTiO 5 ceramic

Mullite-type $R$Mn 2 O 5 ($R$ = Y, rare-earth element) ceramics are of ongoing research attention because of their interesting crystal-chemical and magnetic properties. We report nuclear and magnetic structures of NdMnTiO 5 together with its spectroscopic, thermogravimetric, and magnetic properties. The polycrystalline sample is prepared by solid-state synthesis and characterized from neutron and X-ray powder diffraction data Rietveld refinements. NdMnTiO 5 crystallizes in the orthorhombic space group $Pbam$ with metric parameter $a$ = 755.20(1) pm, $b$ = 869.91(1) pm, $c$ = 582.42(1) pm, and $V$ = 382.62(1) 10 6 pm 3 . The Mn 3+ and Ti 4+ cations are observed to be located in the octahedral and pyramidal sites, respectively. The vibrational features in these polyhedral sites are characterized by Raman and Fourier transform infrared spectroscopes. The higher decomposition temperature of NdMnTiO 5 , compared to other $R$Mn 2 O 5 phases, is explained in terms of the higher bond strength of Ti-O bonds than those of Mn-O bonds. Temperature-dependent DC magnetic susceptibility suggests a paramagnetic to antiferromagnetic phase transition at 43(1) K. Inverse susceptibility in the paramagnetic region above 120 K follows the Curie-Weiss law, resulting in a magnetic moment of 6.33(1) μ B per formula unit. Neutron diffraction data collected at 7.5 K reveal that the magnetic moments of Nd 3+ and Mn 3+ in NdMnTiO 5 are incommensurately ordered with a propagation vector $k$ = (0, 0.238, 0.117).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗
DOE OSTI2023

Modeling the Effects of Microwave Heating on Densification in Chemical Vapor Infiltration

Microwave heating has great potential to accelerate the synthesis of ceramic matrix composites (CMCs) by a process called Chemical Vapor Infiltration (CVI). In CVI, reactive gases ingress a porous preform and undergo chemical transformation to deposit solid ceramic phase within the pores at high temperature thus, densifying the preform. However, the competing effects of chemical kinetics and gas transport are known to result in non-uniform densification as the outer surfaces of the preform experience faster depositions compared to the core. Achieving spatial temperature control plays a key role improving the densification quality. Microwave heating can potentially create temperature inversion such that the core of the preform is hotter than the outer surface and subsequently, lead to improved densification while keeping the manufacturing times and costs low. In the present work, a computational modeling strategy has been developed that accounts for the key physical phenomena responsible for densification of porous preforms using microwave heating. Specifically, a chemical kinetics model has been formulated for Silicon Carbide (SiC) deposition from MTS/H2 precursor. The model is implemented in a pore-resolved reactive transport solver, Quilt. The CVI simulations are performed for several conditions. Initially, parameterized temperature control is imposed to identify optimum conditions for good densification quality at a fraction of processing time. Further, simulations of microwave heating of porous SiC preforms are performed using OpenFOAM. A strategy to achieve and enhance temperature inversion is identified. The resulting temperature profiles are used in the pore-resolved densification simulations to analyze the densification behavior. It is observed that the temperature inversion achieved by microwave heating leads to significant improvements in densification quality and at the same time, keeps the manufacturing time low.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chemical interaction and enhanced interfacial ion transport in a ceramic nanofiber–polymer composite electrolyte for all-solid-state lithium metal batteries

This article reports the synergy between ceramic nanofibers and a polymer, and the enhanced interfacial Li-ion transport along the nanofiber/polymer interface in a solid-state ceramic/polymer composite electrolyte, in which a three-dimensional (3D) electrospun aluminum-doped Li 0.33 La 0.557 TiO 3 (LLTO) nanofiber network is embedded in a polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP) matrix. Strong chemical interaction occurs between the nanofibers and the polymer matrix. Addition of the ceramic nanofibers into the polymer matrix results in the dehydrofluorination of the PVDF chains, deprotonation of the –CH 2 moiety and amorphization of the polymer matrix. Solid-state nuclear magnetic resonance (NMR) spectra reveal that lithium ions transport via three pathways: (i) intra-polymer transport, (ii) intra-nanofiber transport, and (iii) interfacial polymer/nanofiber transport. In addition, lithium phosphate is coated on the LLTO nanofiber surface before the nanofibers are embedded into the polymer matrix. The presence of lithium phosphate at the LLTO/polymer interface further enhances the chemical interaction between the nanofibers and the polymer, which promotes the lithium ion transport along the polymer/nanofiber interface. This in turn improves the ionic conductivity and electrochemical cycling stability of the nanofiber/polymer composite. As a result, the flexible LLTO/Li 3 PO 4 /polymer composite electrolyte membrane exhibits an ionic conductivity of 5.1 × 10 -4 S cm -1 at room temperature and an electrochemical stability window of 5.0 V vs. Li/Li + . A symmetric Li|electrolyte|Li half-cell shows a low overpotential of 50 mV at a constant current density of 0.5 mA cm -2 for more than 800 h. In addition, a full cell is constructed by sandwiching the composite electrolyte between a lithium metal anode and a LiFePO 4 -based cathode. Such an all-solid-state lithium metal battery exhibits excellent cycling performance and rate capability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Accelerated thermal property mapping of TRISO advanced nuclear fuel

TRistructural ISOtropic (TRISO) fuel is a leading-edge nuclear fuel form representing a departure from the more traditional nuclear fuel forms utilized in the reactor fleet of today. Rather than a monolithic fuel pellet of uranium dioxide, integral fuel forms containing TRISO fuel are composed of thousands of microencapsulated uranium-bearing fuel kernels and individually coated with multiple layers of pyrolytic carbon and silicon carbide. These multilayered ceramic coatings serve as an environmental barrier to ensure radioactive and chemically reactive fission products are contained within the reactor fuel elements, but also participate in the transfer of heat generated in the nuclear fuel to the coolant – the primary purpose of a nuclear reactor. Since traditional thermal property measurement techniques, such as laser flash analysis, would be unable to resolve the thermal properties of the individual TRISO coating layers, a simplified frequency-domain thermoreflectance technique has been developed to rapidly map the thermal properties of TRISO particles. Using this technique, the thermal properties of TRISO particles have been mapped from room temperature up to 1000 °C to examine the spatial variation and temperature-dependency of the thermal properties within each layer. Additionally, spatial-domain thermoreflectance was used to examine the anisotropy of the thermal properties for each layer at different locations within a single TRISO particle, and across multiple TRISO particles to assess the intra- and inter-particle uniformity of thermal properties, respectively. To elucidate the underlying causes for the measured variations in thermal properties, scanning electron microscopy and Raman spectroscopy were used to examine variations in microstructure and chemical bonding within the different coating layers. Results from this work are then compared with previous examinations of TRISO fuel particles and microstructurally driven mechanisms for the variations in the measured thermal properties of the different carbonaceous layers are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructure evolution of gadolinium doped cerium oxide under large thermal gradients

In this report the effects of large thermal gradient annealing on the microstructure of 10 mol% gadolinium doped ceria (GDC) were investigated. GDC powder was prepared by solvent deficient method and sintered at 1650 °C for 10 h to achieve dense ceramics with ~8 μm grain size. The densified GDC samples were subsequently annealed using a 60 W infrared laser at over 2100 °C for 1 h under a thermal gradient equivalent to ~0.3–0.5 °C/μm. The post-annealed samples at 2150 °C for 1 h exhibit grains with average length and width of 37 and 28 μm, respectively. Electron backscattered diffraction (EBSD) analysis revealed that the post-annealed sample at 2150 °C consists of grains oriented close to five principal directions (<4 3 10>, <0 0 1> and <13 1 14> on [0 0 1], and <7 6 20> and <7 2 7> on [0 1 0]) within a tolerance angle of ±10°, whereas the grains of the pre-annealed sample are randomly oriented. Gadolinium diffuses 20–30 μm away from the irradiated surface, with the measured composition of regions deeper than 30 μm, Ce 0.86 Gd 0.14 O 1.93 , is close to that of the pre-annealed sample, Ce 0.87 Gd 0.13 O 1.94 . Enhancement of total conductivity of the post-annealed GDC (1.1 × 10 -3 S cm -1 at 500 °C, and 2.1 × 10 -2 S cm -1 at 700 °C) is observed when compared to the pre-annealed GDC (3.1 × 10 -5 S cm -1 at 500 °C, and 1.7 × 10 -3 S cm -1 at 700 °C), and points to the decrease in the grain boundary (GB) resistivity. This could be attributed to both the change in GB area and grain alignment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hot Hydrogen Testing of W-Coated UN Kernels in a Mo30W Matrix

Ceramic uranium mononitride (UN) is being considered as a reactor fuel for nuclear thermal propulsion. To avoid or reduce the dissociation of UN at the high temperatures needed, embedding it in a metallic matrix (cermet) has been proposed. To assess the viability of this concept, hot hydrogen testing of tungsten-coated UN kernels embedded in a Mo-30 wt% W (Mo30W) alloy matrix has been performed at temperatures from 1800°C to 2300°C. Both the isolated kernels and kernels consolidated by spark plasma sintering in the Mo30W matrix were tested. In addition to direct observations and mass loss measurements, the samples were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS) after each run. The decomposition of UN started at 1800°C despite the coating and matrix, and increased at 2000°C. Uranium seeped through the tungsten grain boundaries of the coating at all temperatures. The consolidated sample expanded irregularly at 2000°C through the formation of voids, and SEM/EDS analysis showed uranium-containing veins in the matrix consisting of U 2 Mo according to the XRD data. The observed pore generation at 2000°C was explained by the formation of water vapor from residual oxides and diffused hydrogen. At 2200°C and above, both the kernels and the consolidated samples melted through the formation of uranium or low–melting point uranium-molybdenum alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Ab-initio informed cluster dynamics simulation of self- and Xe diffusivity in uranium mononitride under irradiation

Uranium mononitride (UN) is one of the ceramic nuclear fuel alternatives to oxide fuels considered for light water reactor and advanced reactor designs, as it presents significant advantages such as high uranium density (better economics) and high thermal conductivity and melting point (increased safety). Self- and fission gas diffusivities need to be better understood, given that they influence key fuel performance phenomena like swelling and fission gas release. Recently, radiation enhanced diffusivity was investigated in UN by means of cluster dynamics simulations relying on empirical potential-based parameterizations, the reliability of which highly depends on the interatomic potential accuracy. Here, in this work, we refine this approach by determining, using ab-initio calculations, the properties of defect clusters containing vacancies, self-interstitials and Xe impurities. We also consider larger clusters than previous studies. The obtained dataset (formation enthalpies, entropies, and migration barriers) is used to parameterize a cluster dynamics model of mobile clusters, and to calculate the defect cluster concentrations under irradiation. This gives us access to the radiation enhanced self- and fission gas diffusivities. Although the resulting diffusivities are close to the values reported in the literature, we find important qualitative differences in the diffusion mechanisms. Capturing the correct mechanisms is crucial to properly describe the chemistry and fission rate dependence of the model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Thermal-shock experiments for separate-effects validation of UO 2 fuel fracture models

Because of the important role that fracture plays in the behavior of ceramic UO2 fuel in a nuclear reactor environment, fracture models are a major component of fuel performance codes. As with any aspect of fuel performance, it is crucial to validate these fracture models against experimental data; however, obtaining well-controlled data for conditions representative of a reactor environment is difficult. Quenching is proposed here as a relatively simple approach for using a laboratory environment to achieve conditions that approximate those of a reactor environment. In this paper, an experimental apparatus containing a single instrumented fuel pellet in a sealed section of copper tubing is developed. It is then applied to a series of seven experiments in which the apparatus is first heated to a high temperature (580-680°C) by immersion in a molten salt bath, then quenched in a cold bath (-10-4 °C). Development of these experiments was guided by numerical simulations, and post-test simulations were performed to aid in understanding the experimental behavior and assessing the accuracy of the predictions of fracture initiation and propagation. In addition, similar experiments were performed on solid copper rods to provide temperature-dependent heat transfer coefficients for use in simulations of these experiments. Here, this study demonstrates that quenching is a viable approach for generating thermal gradients representative of those in prototypical light-water reactor conditions at powers of about 5–10 kW/m. Fracture is expected to begin at these power levels, and moderate amounts of radial and axial cracking was observed in these quenching tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

High-pressure CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes

CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes at high pressures/temperatures are critical to their CO 2 separation and membrane reactor applications, but such data are not available in the literature. Here, this work aims to study the effect of high transmembrane pressure on CO 2 permeation flux and the stability of molten carbonate in the dual-phase samarium-doped ceria (SDC) and molten-carbonate (MC) membranes. Dead-end porous SDC tubular supports were made by a cold isostatic press (CIP)/sintering method with a low porosity (below 7%), and gas-tight SDC-MC membranes were prepared by direct infiltration of molten lithium and sodium carbonate mixture into SDC pores, with a MC volume fraction less than 7%. CO 2 permeation/separation tests were performed on the SDC-MC membranes using feed gas of equal molar CO 2 /N 2 mixture at feed pressures up to 15 atm and sweep gas of helium at 1 atm. CO 2 permeation flux for the SDC-MC membranes depends logarithmically on feed/permeate CO 2 pressure ratio in 660–810°C. The temperature dependence of CO 2 permeation shows activation energy of 30 kJ/mol. Due to the small MC volume fraction and hence low effective carbonate conductivity, CO 2 permeation of the SDC-MC membranes is dominated by the carbonate ionic conduction in the MC phase. The SDC-MC membranes remain in the same structure, morphology, and gas-tightness after CO 2 separation tests at high feed pressures and temperatures, showing high stability of SDC-MC membranes for high-temperature, high-pressure separation and chemical reaction applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Cluster dynamics simulations of tritium and helium diffusion in lithium ceramics

Tritium (T) and He diffusion in LiAlO 2 and LiAl 5 O 8 phases influences the performance of tritium producing burnable absorber rods (TPBARs) by affecting the gas release, swelling and thermal conductivity of Li-bearing ceramic pellets. Frenkel pair defects and clusters created by irradiation can attract T and He interstitials and form clusters of the type He i x Li, He i x Al, He i x O, T i x Li, T i x Al, and T i x O, 1 ≤ x ≤ 4 in a Li, Al or O vacancy site (notation denotes x He or T atoms in a 1 Li, 1 Al or 1 O vacant site). The concentration and mobility of each of these clusters collectively contribute to the diffusion of the He and T gases in LiAlO 2 and LiAl 5 O 8 . Here, in this work, free energy cluster dynamics simulations implemented in the Centipede code, are used to obtain the concentration and diffusivities of these clusters which are then used to calculate the total diffusivity of T and He gases in LiAlO 2 and LiAl 5 O 8 . The results show that diffusivity of T is at least one order of magnitude higher in LiAlO 2 as compared to that in LiAl 5 O 8 whereas He diffusion is 2–13 orders of magnitude higher in LiAlO 2 as compared to that in LiAl 5 O 8 . There is a higher concentration of highly diffusive species (T interstitials and T i 03 Li for the case of tritium and He i 01 Li, He i 02 Li, and He i 03 Li for the case of He) in LiAlO 2 than in LiAl 5 O 8 which increase the total diffusion of T and He in LiAlO 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ characterization of foreign object damage (FOD) in environmental-barrier-coated silicon carbide (SiC) ceramic

Environmental barrier coatings (EBCs) protect advanced ceramics and ceramic matrix composites (CMCs) from oxidation and corrosion in gas turbine engine environments. Foreign object damage (FOD), where debris impact the protective coatings, is a critical hazard which limits the turbine durability. Despite previous efforts to understand FOD in EBCs, a detailed understanding of the fundamental transient damage mechanisms is still lacking. In the current work, the real-time FOD behavior of a Mullite / Silicon EBC was visualized via a dynamic synchrotron X-ray source in phase contrast imaging (PCI) configuration. Prior to the in situ FOD experiments, the microstructure and composition of the coating were respectively characterized using a scanning electron microscope (SEM) and X-ray diffraction (XRD). The variation in the properties of the debris was modeled by ~ 1.5 mm diameter Partially Stabilized Zirconia (PSZ) and Silicon Nitride (Si 3 N 4 ) spheres. A modified light-gas gun setup, synchronized with the X-ray beam, was used to propel the projectiles at velocities ranging between 300 and 355 m·s -1 . Coated samples were impacted under a fully backed support configuration and at normal incidence. Coating penetration and delamination, as well as projectile deformation at the bond coat resulted for FOD by PSZ spheres. Comparatively, projectile fracture, with subsequent rebound of fragments, as well as complete coating penetration and delamination at the substrate interface occurred for FOD by Si 3 N 4 spheres. It should be noted that only cone cracking was observed for FOD by PSZ spheres while back surface cracking was present for both projectile types. Qualitative understanding of the driving forces for the observed damage mechanisms were provided.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Accelerating the Discovery of New, Single Phase High Entropy Ceramics via Active Learning

High-entropy ceramics have garnered interest due to their remarkable hardness, compressive strength, thermal stability, and fracture toughness; yet the discovery of new high-entropy ceramics (out of a tremendous number of possible elemental permutations) still largely requires costly, inefficient, trial-and-error experimental and computational approaches. The entropy forming ability (EFA) factor was recently proposed as a computational descriptor that positively correlates with the likelihood that a 5-metal high-entropy carbide (HECs) will form the desired single phase, homogeneous solid solution; however, discovery of new compositions is computationally expensive. If you consider 8 candidate metals, the HEC EFA approach uses 49 optimizations for each of the 56 unique 5-metal carbides, requiring a total of 2744 costly density functional theory calculations. Here, we describe an orders-of-magnitude more efficient active learning (AL) approach for identifying novel HECs. To begin, we compared numerous methods for generating composition-based feature vectors (e.g., magpie and mat2vec), deployed an ensemble of machine learning (ML) models to generate an average and distribution of predictions, and then utilized the distribution as an uncertainty. Here we then deployed an AL approach to extract new training data points where the ensemble of ML models predicted a high EFA value or was uncertain of the prediction. Our approach has the combined benefit of decreasing the amount of training data required to reach acceptable prediction qualities and biases the predictions toward identifying HECs with the desired high EFA values, which are tentatively correlated with the formation of single phase HECs. Using this approach, we increased the number of 5-metal carbides screened from 56 to 15,504, revealing 4 compositions with record-high EFA values that were previously unreported in the literature. Our AL framework is also generalizable and could be modified to rationally predict optimized candidate materials/combinations with a wide range of desired properties (e.g., mechanical stability, thermal conductivity).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Computational simulation of asymmetric phase transformation in cracked Li₇La₃Zr₂O₁₂: Variant selection and chemo-mechanical implications

Coupling between microcracks and phase transformation in ion-conducting ceramics can jointly affect mechanical responses and ion transport. In this work we investigate the cubic-to-tetragonal phase transformation in Li₇La₃Zr₂O₁₂ in the presence of a microcrack under hydrostatic loading and quantify its implications for crack-tip stress concentration and Li-ion transport using phase-field and molecular dynamics simulations. The phase transformation exhibits a strong asymmetry between hydrostatic tension and compression. Under tension, the crack edge nucleates one tetragonal variant that amplifies the crack-tip stress intensity and promotes crack opening. Under compression, the crack tip nucleates a different tetragonal variant that enhances the stress-induced crack-closure tendency. Effective Li diffusivity analysis shows faster transport degradation under compression due to accelerated transformation kinetics, exposing a trade-off between mechanical stability and ionic conductivity. These results highlight the intertwined nature of cracking, phase transformation, and ionic transport in ion-conducting oxides and provide mechanistic insights into chemo-mechanical degradation of solid electrolytes.

36 MATERIALS SCIENCE↗