Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ceramic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Investigation of R-Curve Behavior in Glass Ceramic Materials

We demonstrate the ability to measure R-curves of brittle materials using a method adapted from Theo Fett et al. The method is validated with a NIST standard reference material and demonstrated using Si 3 N 4 of two different microstructures; glass-ceramic, and PZT. As expected, each material's R-curve is seen to be slightly different with glass-ceramics showing the most pronounced R-curve effects. Plans for future applications and experimental efforts are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling between interfacial charge and mechanical deformation at high temperatures in ceramics. Final report

Basic research, under this project, has led to new fundamental discoveries in the effect of electric field (and temperature) on diffusion kinetics, electroluminescence and electronic conductivity in ceramic materials. For example, yttria stabilized zirconia sinters in just seconds well below 1000°C, while, at the same time, exhibiting a highly non-linear rise in conductivity, and intense electroluminescence. The phenomenon has been shown to occur in nearly all ceramics whether they are ionic or electronic conductors, or insulators. The rise in conductivity leads to Joule heating but in-situ measurements with a platinum standard at APS and Brookhaven (NSLS-II) have shown that the temperatures are much below what would have been needed to sinter in a few seconds. We have explored the hypothesis that huge concentrations of Frenkel pairs of vacancies and interstitials are produced. While these point defects accelerate sintering (by the interstitials being transported to the pores and the vacancies to the grain boundaries), they may also produce electron-hole pairs which can impart high electrical conductivity or recombine to emit photons. Many measurements, including in-situ measurements of lattice expansion are consistent with this hypothesis. However, the energy barrier for generating Frenkels in zirconia for example is much larger than can be expected at temperature and electrical fields in these experiments. Most recent work suggests that short wavelength phonons play a critical role in the genesis of the “flash” phenomenon. For example, the Debye temperature has been shown to be the lower bound for initiating flash. Molecular dynamics simulations have shown that large concentrations of Frenkel pairs can form under the proliferation of “optical” phonons at the edge of the Brillouin zone, that is with a wavelength at or below the lattice parameter. This project has led to the development of new experimental techniques as well as a software hardware interface for process and control and data analysis in real time, with a time scale of less than one second. This approach spells a new paradigm in materials science research. It potential impact on high rate manufacturing is self evident.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synergistic Effect of High Sulfur Loading Layered Cathode, Ceramic Separator and Gel Electrolyte

Lithium sulfur (Li-S) batteries are promising candidates for next-generation energy storage devices as they are capable of providing higher energy density and lower cost in comparison to the state of the art Li-ion batteries. To gain these characteristics, there are challenges such as polysulfide crossover, large volume changes during cycling, and deposition of insulating lithium sulfide that need to be alleviated. A popular approach to address these issues is to control the structure and properties of the carbon cathode in order to influence the transport of polysulfides, surface area for reaction, and lithium sulfide deposition. Ceramic separators on the other hand can drastically affect ion diffusion and overall battery performance. Safety concerns regarding the flammable liquid electrolyte can be reduced by deploying gel electrolyte. Towards this direction, we developed a layer-on-layer cathode structure with sulfur-impregnated activated carbon alternating with graphene layer, which was fabricated by Air-assisted electrospray. A much higher sulfur loading compared to slurry cast cathodes can be provided in this method. Combining the new cathode with gel electrolyte can offer higher safety of the battery and capacity retention. Ceramic separator would compensate the reduced ion conductivity of the gel electrolyte and the combination of these variables will be very promising in improvement of battery performance and safety.

25 ENERGY STORAGE↗
DOE OSTI2022

Processing, structure, and thermal properties of ZrW 2 O 8 , HfW 2 O 8 , HfMgW 3 O 12 , Al(HfMg) 0.5 W 3 O 12 , and Al 0.5 Sc 1.5 W 3 O 12 negative and zero thermal expansion coefficient ceramics

Negative and zero coefficient of thermal expansion (CTE) materials are of interest for developing polymer composites in electronic circuits that match the expansion of Si and in zero CTE supports for optical components, e.g., mirrors. In this work, the processing challenges and stability of ZrW 2 O 8 , HfW 2 O 8 , HfMgW 3 O 12 , Al(HfMg) 0.5 W 3 O 12 , and Al 0.5 Sc 1.5 W 3 O 12 negative and zero thermal expansion coefficient ceramics are discussed. Al 0.5 Sc 1.5 W 3 O 12 is demonstrated to be a relatively simple oxide to fabricate in large quantity and is shown to exhibit single phase up to 1300 °C in air and inert N 2 environments. The negative and zero CTE behavior was confirmed with dilatometry. Thermal conductivity and heat capacity were reported for the first time for HfMgW 3 O 12 and Al 0.5 Sc 1.5 W 3 O 12 and thermal conductivity was found to be very low (~0.5 W/mK). Grüneisen parameter is also estimated. Methods for integration of Al 0.5 Sc 1.5 W 3 O 12 with other materials was examined and embedding 50 vol% of the ceramic powder in flexible epoxy was demonstrated with a commercial vendor.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compositional Exploration of Additively Manufactured Ultra-High-Temperature Ceramic Composites for Use in Concentrated Solar Power Plant Heat Exchangers

The DOE has research interest in new technologies for high temperature concentrated solar power plants. Our project this summer was to explore the use of additively manufactured ultra-high-temperature ceramics in a heat exchanger. The heat exchanger would transfer heat between a molten chloride salt and supercritical CO 2 . We selected 22 compositions to test and were able to mix 14 of these compositions. We sintered these compositions using pressureless sintering and direct current sintering. We also conducted high temperature TGA on some ceramic samples. We also performed preliminary binder jet additive manufacturing trials with tungsten carbide powder. Our work so far points towards one of our titanium diboride samples being promising, but much more research needs to be done.

14 SOLAR ENERGY↗
DOE OSTI2021

High-Entropy Ceramic Coatings: Transformative New Materials for Environmentally-Compatible Thin-Film Insulators against High-T Molten Salts

An emerging new class of promising materials, High-Entropy Ceramics (HECs) or Compositionally-Complex Ceramics (CCCs), have been successfully fabricated in the last three years. This project evaluates HECs/CCCs in the concentrated solar power (CSP) context. In this project, we have identified a couple of simple, and key descriptors governing thermal conductivity in HECs. Size disorder among the cations was found to have a strong influence on the thermal conductivity across multiple systems and throughout a vast compositional space. Since identifying this, we have optimized previous compositions to achieve low thermal conductivities of $k$~$1-1.4Wm{-1}K{-1}$. We have further reduced our selection of promising compositions based on project guidelines and applied a theory that can potentially predict reactivity with molten salts to identify a small set of HECs that are suitable for further molten salt heat transfer media (HTM) stability testing. Many compositions reveal poor resistance to molten chloride salt after being exposed for 24 h compared to the reference structural alloy, Haynes 230. However, after 100 h, a few HECs/CCCs show strong parabolic rate constant effects and provide greater resistance to chloride salt compared to Haynes 230 alloy, which shows more linear kinetics. Postmortem characterization of the microstructure reveals the parabolic rate constant originates from a dense reaction layer form at the interface. This feature is absent in Haynes 230, which only shows grain boundary infiltration. The HECs/CCCs were also put in contact with the metal alloy under Ar for 800 h at 800°C and show negligible interaction. Lastly, parabolic rate constant HECs/CCCs also have low thermal conductivity $(<2 Wm^{-1} K^{-1})$ at 800°C. These specimens satisfy all project requirements and demonstrate their promising application in next-generation CSP.

14 SOLAR ENERGY↗
DOE OSTI2023

Statement of Work: Toward AI-driven additive manufacturing for metal-ceramic composite structures

The project scope is to investigate the compatibility of various ceramic and metal powder composite feedstock development, implement AI algorithms for in-situ monitoring and parameter optimization of binder jet 3D printing to achieve reliable and robust metal/ceramic and/or ceramic/ceramic composite components, and create a generative design framework for heterogeneous composite structures incorporating metals and ceramic-based materials to achieve specific mechanical properties. Funded is the effort and travel by the faculty advisor at University of California Berkeley in support of the work of their students and the related collaborative research and development effort.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Dynamic, robust, radiation-resistant ceramics: harnessing thermodynamic and kinetic driving forces (Final Report)

The overarching objective of this project was to establish a class of structural ceramics with enhanced radiation tolerance based on a dynamic microstructure by harnessing the synergistic effects of radiation enhanced diffusion, capillarity and thermally induced mass transport on microstructural evolution. Specifically, we aimed to quantify changes in mass transport behavior that may influence the microstructural evolution of ionic/covalent ceramic materials subjected to irradiation.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Scalable, Infiltration-Free Ceramic Matrix Composite Manufacturing for Molten Salt Receiver (SIF-CMC)

Ceramic Matrix Composite (CMC) with high thermomechanical properties is a promising material class for Concentrated Solar Power but current use is limited by a long and tedious manufacturing process with high costs and poor scalability. SIF-CMC provides a novel way to simplify the manufacturing process by dramatically increasing the char yield of the matrix from polymer to ceramic, which makes the CMC affordable and scalable.

Wei, Junhua↗
DOE OSTI2024

Modularization of Ceramic Hollow Fiber Membrane Technology for Air Separation

This proposed project is aimed at studying high performance and economically competitive ceramic membrane technology for air separation and high-purity oxygen production using hollow fiber ceramic membrane stack and module technology. The design of the single permeate membrane is a hollow fiber substrate-supported thin tri-layer structure. Radially well-aligned micro-channels are embedded in the thick substrate and open at the inner surface of the substrate, enabling facile air/gas diffusion. The tri-layer structure of thin dense membrane layer (~ 10 µm) sandwiched by porous surface layer on either side is then built on the substrate using advanced fabrication process. The tri-layer structure design allows different materials to be used in different layers, where the materials of surface layers have high surface exchange coefficients while the material of dense layer has high bulk diffusivity. Such a synergetic combination leads to high permeation performance. The focus of the proposed project will be on membrane stack/module development using the developed single hollow fiber membranes, including: 1) fabrication and characterization of novel single hollow fiber membranes; 2) membrane stack design and assembly using fabricated single membranes; 3) stack modeling and analysis to guide membrane stack designs; 4) permeation performance testing and characterization of membrane stacks. The hollow fiber feature and simple sealing requirement enable very compact design of membrane stacks, which have excellent flexibility for further modularizations at different scales. The operations of such membrane stack and module may employ the exhaust heat from other components of Integrated Gasification Combined Cycle and oxy-combustion systems. Therefore, modularization of such an air separation membrane technology can be incorporated into the DOE’s REMS (radically engineered modular systems)-gasification skid and support the oxidant feed of an oxygen-blown REMS gasifier scaled to different ranges.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Exploitation of Defects in High Entropy Ceramic Barrier Materials

A critical mission need exists to develop new materials that can withstand extreme environments and multiple sequential threats. High entropy materials, those containing 5 or more metals, exhibit many exciting properties which would potentially be useful in such situations. However, a particularly hard challenge in developing new high entropy materials is determining a priori which compositions will form the desired single phase material. The project outlined here combined several modeling and experimental techniques to explore several structure-property-relationships of high entropy ceramics in an effort to better understand the connection between their compositional components, their observed properties, and stability. We have developed novel machine learning algorithms which rapidly predict stable high entropy ceramic compositions, identified the stability interplay between configurational entropy and cation defects, and tested the mechanical stability of high entropy oxides using the unique capabilities at the Dynamic Compression Sector facility and the Saturn accelerator.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Near-net shaping of high-density, complex, spatially-tailored ceramics for extreme environments

The purpose of this subcontract is for LLNL to collaborate with the Subcontractor (UCSB) in the areas of binder jet additive manufacturing (BJAM), hot pressing (HP), finite element modeling (FEM), and multi-material sintering studies. LLNL wants to further develop its hot pressing, AM, and modeling capabilities through LLNL’s Early Career Faculty Program. This work will focus on developing a method to hot press complex-shaped ceramic parts through the co-deposition of a structural/functional ceramic and sacrificial mold material in one assembly via multi-material binder jet printing. The method aims to produce dense, near-net shaped parts with applications relevant to a wide variety of fields including aerospace, defense, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Direct Processing of Lithium Chloride Based Waste Salt in a Ceramic Waste Form

Ceramic waste form materials were fabricated with a LiCl based salt mixture to demonstrate the suitability of direct processing of waste salt from an all LiCl pyroprocessing flow sheet on the formation, microstructure, and durability of ceramic waste forms. Materials were successfully synthesized by using the simplified direct processing technique with salt loadings of 5, 7.5, and 10 wt% at the laboratory scale. Materials fabricated with LiCl based salt indicated full conversion of zeolite to sodalite occurred to form products with low open porosity. This indicates that the Na 2 O content of NBS4 glass is suitable for processing salt chemistries which do not contain NaCl. Generated sodalite was microencapsulated by the glass binder, halite occlusions were detected within sodalite domains at all salt loadings, and a Cs-rich phase believed to be Cs-pollucite was detected in the material made with the lowest salt loading (5 wt%). Salt inclusions were encapsulated within the binder glass at all loadings, and found to consist primarily of NaCl with Cs present. A small amount of salt was found at the surface of the wasteform made with the highest salt loading of 10 wt%, which may indicate an upper limit to the amount of salt that can be accommodated or incomplete mechanical mixing of the reagents. Durability testing by using the ASTM C1308 method indicated that initial rapid dissolution of exposed halite inclusion phases was directly correlated to salt loading. Wasteform degradation during all tests occurred primarily due to dissolution of the sodalite phase. Durability of the binder glass was found to increase as the waste salt loading increased. Results for the release of cations from the salt indicate the changes in wasteform durability and halite inclusion chemistry are strongly influenced by ion exchange phenomena between the salt and the glass. This appears to be the result of the relatively stronger affinity for the glass phase of Li, compared to that of other cations such as Na and Cs. The effects from cation exchange were diminished at lower salt loadings.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Ceramic Composite Experimental Testing Status

Over recent years, ceramic matrix materials such as SiC–SiC and C–C have been gaining interest for use in fusion reactors, light water reactors (LWRs), and high-temperature reactors (HTRs). These materials are good candidates to operate in very high temperature and moderate to high radiation environments. The evaluation of composite materials, in general, is challenging because of variations in precursor materials, variations in the fabrication process across fabricators, and the wide range of potential fiber architectures, to name a few. However, the need to evaluate neutron-irradiated properties adds another layer of complexity, which includes cost, timeline, and specimen size limitations (often associated with irradiation testing). A qualification methodology for the use of ceramic composites is provided in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section III-5-HHB. The methodology is supported by ASTM International (ASTM) guides, which provide a pathway to accomplish this effort. Part of the qualification strategy is for the designer to collect material property data on environmental conditions representative of its design envelope. These data include irradiation effects. This report presents an experimental study and test campaign developed to partially address this gap by providing initial mechanical and physical property data required for design. A variety of different materials using different manufacturing techniques are considered as part of this campaign. The test plan suggests performing a screening or partial irradiation study to assist the designer during the material selection process. The designer can then perform a more comprehensive qualification study if the material performance is promising. This work focuses on the status of the specimen preparations (machining of samples), the current test methods and failure analysis as well as the preparation of irradiation vehicles for the irradiation campaign. The irradiation will be performed at Oak Ridge National Laboratory (ORNL) in the High Flux Isotope Reactor (HFIR) and at Idaho National Laboratory (INL) in the Advanced Test Reactor (ATR).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Elastic Modulus Measurement at High Temperatures for Miniature Ceramic Samples Using Laser Micro-Machining and Thermal Mechanical Analyzer

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale at high temperatures. We used a picosecond laser to precisely cut microbeams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm and a length of ~1 cm. They were then tested in a thermal mechanical analyzer at room temperature, 500 °C, 800 °C, and 1100 °C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Chemistry↗
DOE OSTI2023

Direct Ink-Write Printing of Ceramic Clay with an Embedded Wireless Temperature and Relative Humidity Sensor

This research presents a simple method to additively manufacture Cone 5 porcelain clay ceramics by using the direct ink-write (DIW) printing technique. DIW has allowed the application of extruding highly viscous ceramic materials with relatively high-quality and good mechanical properties, which additionally allows a freedom of design and the capability of manufacturing complex geometrical shapes. Clay particles were mixed with deionized (DI) water at different ratios, where the most suitable composition for 3D printing was observed at a 1:5 w/c ratio (16.2 wt.%. of DI water). Differential geometrical designs were printed to demonstrate the printing capabilities of the paste. In addition, a clay structure was fabricated with an embedded wireless temperature and relative humidity (RH) sensor during the 3D printing process. The embedded sensor read up to 65% RH and temperatures of up to 85 °F from a maximum distance of 141.7 m. The structural integrity of the selected 3D printed geometries was confirmed through the compressive strength of fired and non-fired clay samples, with strengths of 70 MPa and 90 MPa, respectively. This research demonstrates the feasibility of using the DIW printing of porcelain clay with embedded sensors, with fully functional temperature- and humidity-sensing capabilities.

42 ENGINEERING↗
NASA NTRS1972

Improved method for producing metal-reinforced ceramics

Vacuum impregnation process produces metal-reinforced ceramics with only 3 percent void space volumes. Method may be used to produce metal-reinforced ceramics for high temperature or structural applications such as furnace supports and armor.

Landingham, R. L.↗