Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CLADDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Is spent nuclear fuel immune from delayed hydride cracking during dry storage? An IAEA coordinated research project - 2016-0048

Delayed hydride cracking (DHC) has been responsible for cracking in zirconium alloy pressure tubes and fuel cladding and is a concern for spent fuel storage. For cracking to start, sufficient hydrogen must be present for hydride to form at a flaw tip and the local tensile stress must be sufficiently large to crack the hydride (a crack will not extend if the threshold in the stress intensity factor, K{sub IH}, is not exceeded. A high-temperature limit exists when the yield stress of the cladding alloy becomes too low to crack the hydride. In this paper we describe measurements of K{sub IH} and the crack growth rate, V, in unirradiated Zircaloy-4 fuel cladding containing approximately 130 ppm hydrogen in the cold-worked stress-relieved condition representing pressurized water reactors (PWRs) and pressurized heavy-water (PHWR) reactors. Four methods are used to evaluate K{sub IH}. The test specimen and fixture used in these methods was the pin-loading tension configuration. The test temperature ranged from 227 to 315 deg. C. The mean value of K{sub IH} below 280 deg. C had little temperature dependence; it was about 5.5 MPa√m in the PWR cladding and slightly higher at 7 MPa√m in the PHWR material. At higher test temperatures, K{sub IH} increased dramatically to more than 12 MPa√m, whereas the crack growth rate declined toward zero. This behavior suggests that unirradiated Zircaloy-4 fuel cladding is immune from DHC above about 320 deg. C; this temperature may be increased to 360 deg. C by irradiation. The implications for spent fuel storage are that during early storage when the temperatures are high, any flaw will not extend by DHC, whereas at low temperatures, after many years of storage, flaws would have to be very large, approaching through wall, before being extended by DHC. To date, spent nuclear fuel is not known to have failed by DHC during storage, confirming the inference. (authors)

36 MATERIALS SCIENCE↗

Effect of hydrogen on irradiation creep and growth for ZIRLO alloy and Zr-1.0Nb - 2016-0058

The impact of hydrogen on the irradiation growth and creep of stress-relief annealed (SRA) ZIRLO{sup R} alloy and recrystallized annealed (RXA) Zr-1.0Nb cladding tubes is evaluated in this paper. The samples were charged with hydrogen in the range of approximately 160-720 ppm using the gaseous method. Biaxial in-reactor creep tests were performed after Cycle 1, Cycle 2, Cycle 3, and Cycle 4, on both as received and pre-charged hydrogen cladding tubes. Outside diameter and axial length measurements were performed on the samples. The results showed that hydrogen had no effect on the axial irradiation creep but a relatively large effect on the axial irradiation growth. Increasing hydrogen decreased the axial irradiation growth in RXA Zr-1.0 Nb, which was opposite from the behavior of SRA ZIRLO cladding. This unique hydrogen effect on the irradiation axial growth of RXA Zr-1.0Nb could be due to the different intergranular stress resulting from the fabrication process or the absence of alloying elements, including tin. The total axial strain of both Zr-1.0Nb and SRA ZIRLO cladding increased with increasing fast fluence, and Zr-1.0Nb increased at a faster rate relative to SRA ZIRLO cladding. In the diameter direction, hydrogen had a minimal effect on the total diameter strain and the diameter irradiation creep strain for both SRA ZIRLO samples and the RXA Zr-1.0Nb sample. This finding from in-reactor test is contrary to the out-reactor tests results from the literature that have shown that hydrogen significantly decreases thermal creep. The total diameter strain and diameter irradiation creep behavior for the SRA ZIRLO samples and RXA Zr-1.0Nb were similar. (authors)

36 MATERIALS SCIENCE↗

Mechanical behavior at high temperatures of highly oxygen- or hydrogen-enriched α and prior-β phases of Zirconium alloys - 2016-0063

During a hypothetical loss-of-coolant accident, zirconium alloy fuel claddings can be loaded by internal pressure and exposed to steam at high temperatures (HTs) up to 1,200 deg. C and then cooled and quenched in water. A significant fraction of the oxygen that reacts with the cladding during HT oxidation diffuses beneath the oxide through the metallic substrate. This induces a progressive transformation of the metallic β{sub Zr}-phase layer into an intermediate layer of α{sub Zr}(O) phase containing up to 7 weight % (wt.%) oxygen. Furthermore, in some specific conditions, the cladding may rapidly absorb a significant amount of hydrogen during steam exposition at HTs. As a β{sub Zr} stabilizer, hydrogen would mainly diffuse and concentrate up to several thousands of parts per million by weight (wppm) into the inner β{sub Zr}-phase layer. This study intends to provide new and more comprehensive data on the HT mechanical behavior of the α{sub Zr}(O) and (prior-)β{sub Zr} phases containing high contents of oxygen and hydrogen, respectively. Model samples produced from M5{sup R} and Zircaloy-4 cladding tubes homogeneously charged in oxygen (less than or equal to 6 wt.%) and hydrogen (less than or equal to 3,000 wppm), respectively, were prepared. Their mechanical behavior was determined under vacuum between 800 and 1,100 deg. C for the oxygen-enriched α{sub Zr} phase and in air between 700 and 20 deg. C after cooling from the β{sub Zr} temperature domain for the hydrogen-enriched (prior-)β{sub Zr} phase. The α{sub Zr} phase was substantially strengthened and embrittled by oxygen. The contribution of the α{sub Zr}(O) layer to the HT creep behavior of an oxidized fuel cladding tube subjected to internal pressure is evaluated by finite element analysis. Mechanical strength and ductility of the model (prior-)β{sub Zr} phase appear to be affected by hydrogen contents of 2000-3000 wppm in ways that depend on temperature. (authors)

36 MATERIALS SCIENCE↗

Nuclear Energy Advanced Modeling and Simulation (NEAMS) Accident Tolerant Fuels High Impact Problem: Coordinate Multiscale FeCrAl Modeling

Since the events at the Fukushima-Daiichi nuclear power plant in March 2011 significant research has unfolded at national laboratories, universities and other institutions into alternative materials that have potential enhanced ac- cident tolerance when compared to traditional UO2 fuel zircaloy clad fuel rods. One of the potential replacement claddings are iron-chromium-alunimum (FeCrAl) alloys due to their increased oxidation resistance [1–4] and higher strength [1, 2]. While the oxidation characteristics of FeCrAl are a benefit for accident tolerance, the thermal neu- tron absorption cross section of FeCrAl is about ten times that of Zircaloy. This neutronic penalty necessitates thinner cladding. This allows for slightly larger pellets to give the same cold gap width in the rod. However, the slight increase in pellet diameter is not sufficient to compensate for the neutronic penalty and enriching the fuel beyond the current 5% limit appears to be necessary [5]. Current estimates indicate that this neutronic penalty will impose an increase in fuel cost of 15-35% [1, 2]. In addition to the neutronic disadvantage, it is anticipated that tritium release to the coolant will be larger because the permeability of hydrogen in FeCrAl is about 100 times higher than in Zircaloy [6]. Also, radiation-induced hardening and embrittlement of FeCrAl need to be fully characterized experimentally [7]. Due to the aggressive development schedule for inserting some of the potential materials into lead test assemblies or rods by 2022 [8] multiscale multiphysics modeling approaches have been used to provide insight into these the use of FeCrAl as a cladding material. The purpose of this letter report is to highlight the multiscale modeling effort for iron-chromium-alunimum (FeCrAl) cladding alloys as part of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program through its Accident Tolerant Fuel (ATF) High Impact Problem (HIP). The approach taken throughout the HIP is to utilize lower length scale approaches (e.g., density functional theory, cluster dynamics, rate theory, phase field, and Visco-Plastic- Self-Consistent (VPSC)) to develop more physically informed models at the engineering scale for use in the BISON [9] fuel performance code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Establishing New Capability of High Temperature Electrochemical Impedance Spectroscopy Techniques for Equilibrium and Kinetic Experiments

In nuclear fuel and cladding materials, changes in structure and chemistry over the lifetime of the fuel can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides coupling with modeling such as finite element (FE) and other material characterization techniques such as atom probe tomography (APT), Raman spectroscopy, in-situ Transmission Electron Microscopy (TEM), and synchrotron X-ray microscopy. The objective of this work package is to develop EIS techniques for the in-pile measurement of changes in solid state chemistry of fuels and materials in coupling with model simulation and material characterization. This work package will involve the initial development of electrochemical sensing technologies for measuring spatial- and time-resolved changes in fuel and cladding chemistry. Specific attention will be paid to monitoring changes in fuel stoichiometry, monitor cladding hydride formation and deformation, and cladding corrosion. This report summarized the FY17 achievements of this work package. A laboratory was begun to set up from scratch. The laboratory place was located; necessary equipment and materials were purchased and some were delivered; laboratory instruction (LI) for conducting experiments was drafted for review; radiation level of depleted UO2 that will be investigated as the potential testing sample was valued for safety issue; a testing plan for measuring changes in stoichiometry of oxide fuels has been made and roadblocks for making measurements at high temperature have been pinpointed; in addition, collaboration with Boise State University (BSU) and Massachusetts Institute of Technology (MIT) has been established. In short, the capability of applying EIS for in-pile measurement of changes of fuels and cladding materials was initiated to be established.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Irradiation Performance of U-Mo Alloy Based ‘Monolithic’ Plate-Type Fuel – Design Selection

A down-selection process has been applied to the U-Mo fuel alloy based monolithic plate fuel design, supported by irradiation testing of small fuel plates containing various design parameters. The irradiation testing provided data on fuel performance issues such as swelling, fuel-cladding interaction (interdiffusion), blister formation at elevated temperatures, and fuel/cladding bond quality and effectiveness. U-10Mo (wt%) was selected as the fuel alloy of choice, accepting a somewhat lower uranium density for the benefits of phase stability. U-7Mo could be used, with a barrier, where the trade-off for uranium density is critical to nuclear performance. A zirconium foil barrier between fuel and cladding was chosen to provide a predictable, well-bonded, fuel-cladding interface, allowing little or no fuel-cladding interaction. The fuel plate testing conducted to inform this selection was based on the use of U-10Mo foils fabricated by hot co-rolling with a Zr foil. The foils were subsequently bonded to Al-6061 cladding by hot isostatic pressing or friction stir bonding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Algorithms for thermal and mechanical contact in nuclear fuel performance analysis

The transfer of heat and force from UO{sub 2} pellets to the cladding is an essential element in typical nuclear fuel performance modeling. Traditionally, this has been accomplished in a one-dimensional fashion, with a slice of fuel interacting with a slice of cladding. In this manner, the location at which the transfer occurs is set a priori. While straightforward, this limits the applicability and accuracy of the model. We propose finite element algorithms for the transfer of heat and force where the location for the transfer is not predetermined. This enables analysis of individual fuel pellets with large sliding between the fuel and the cladding. The simplest of these approaches is a node on face constraint. Heat and force are transferred from a node on the fuel to the cladding face opposite. Another option is a transfer based on quadrature point locations, which is applied here to the transfer of heat. The final algorithm outlined here is the so-called mortar method, with applicability to heat and force transfer. The mortar method promises to be a highly accurate approach which may be used for a transfer of other quantities and in other contexts, such as heat from cladding to a CFD mesh of the coolant. This paper reviews these approaches, discusses their strengths and weaknesses, and presents results from each on simplified nuclear fuel performance models. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Regulatory Perspective on Potential Fuel Reconfiguration and Its Implication to High Burnup Spent Fuel Storage and Transportation - 13042

The recent experiments conducted by Argonne National Laboratory on high burnup fuel cladding material property show that the ductile to brittle transition temperature of high burnup fuel cladding is dependent on: (1) cladding material, (2) irradiation conditions, and (3) drying-storage histories (stress at maximum temperature) [1]. The experiment results also show that the ductile to brittle temperature increases as the fuel burnup increases. These results indicate that the current knowledge in cladding material property is insufficient to determine the structural performance of the cladding of high burnup fuel after it has been stored in a dry cask storage system for some time. The uncertainties in material property and the elevated ductile to brittle transition temperature impose a challenge to the storage cask and transportation packaging designs because the cask designs may not be able to rely on the structural integrity of the fuel assembly for control of fissile material, radiation source, and decay heat source distributions. The fuel may reconfigure during further storage and/or the subsequent transportation conditions. In addition, the fraction of radioactive materials available for release from spent fuel under normal condition of storage and transport may also change. The spent fuel storage and/or transportation packaging vendors, spent fuel shippers, and the regulator may need to consider this possible fuel reconfiguration and its impact on the packages' ability to meet the safety requirements of Part 72 and Part 71 of Title 10 of the Code of Federal Regulations. The United States Nuclear Regulatory Commission (NRC) is working with the scientists at Oak Ridge National Laboratory (ORNL) to assess the impact of fuel reconfiguration on the safety of the dry storage systems and transportation packages. The NRC Division of Spent Fuel Storage and Transportation has formed a task force to work on the safety and regulatory concerns in relevance to high burnup fuel storage and transportation. This paper discusses the staff's preliminary considerations on the safety implication of fuel reconfiguration with respect to nuclear safety (subcriticality control), radiation shielding, containment, the performance of the thermal functions of the packages, and the retrievability of the contents from regulatory perspective. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The application of MAMMOTH for a detailed tightly coupled fuel pin simulation with a station blackout

The accurate calculation of desired quantities to predict fuel behavior in a nuclear reactor requires the solution of inter linked equations representing different physics phenomena. Traditional fuels performance codes often rely on internal empirical models for the pin power density and a simplified boundary condition on the cladding outer surface. These simplifications are performed because of the difficulty of coupling applications or codes on differing domains and mapping the required data. In this work the MAMMOTH application is employed in the demonstration of an approach that more consistent with first principles, in a simulation that couples the neutronics application Rattlesnake, the thermal fluids application RELAP-7 and the fuels performance application BISON. A single fuel pin was modeled based on the dimensions of a fuel rod from a Westinghouse 17*17 optimized PWR fuel assembly. The simulation consisted of a depletion period of 1343 days, representing three full operating cycles, followed by a station blackout (SBO) event. The fuel rod was depleted with a total pin power of 65.81 kW. After 1343 days the fission power was reduced to zero (simulating a reactor shutdown). Decay heat calculations provided the time-varying energy source after this time. For this problem, Rattlesnake, BISON, and RELAP-7 are coupled under MAMMOTH in a tightly coupled approach. Each system solves its physics on a separate mesh and, for RELAP-7 and BISON, on only a subset of the full problem domain. Rattlesnake solves the neutronics over the whole domain, which includes the fuel, cladding, gaps, water, and top and bottom rod holders. Here BISON is applied to the fuel and cladding with a 2-D axisymmetric domain, and RELAP-7 is applied to the flow of the circular outer water channel with a set of 1-D flow equations. For this work, the mesh on the Rattlesnake side is either be 3-D (for low order PN transport or diffusion) or 2-D axisymmetric (for diffusion). BISON has a matching ring structure mesh for the fuel so both the power density and local burnup are transferred accurately from Rattlesnake. At each depletion time step, Rattlesnake calculates a power density, fission density rate, burnup distribution and fast flux based on the current water density and fuel temperature. These are then mapped to the BISON mesh to perform a fuels performance solution. BISON calculates the fuel temperature and cladding surface temperature based upon the current power density and bulk fluid temperature. RELAP-7 then calculates the fluid temperature, water density fraction and water phase velocity based upon the cladding surface temperature. The fuel temperature and the fluid density are then passed back to Rattlesnake for another neutronics calculation. For this paper, sets of results from the detailed calculation are provided for both depletion and the SBO event. We demonstrate that a detailed simulation akin to first principles can be achieved using MAMMOTH and the various MOOSE application on differing domains. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Calibration and validation of NRC fuel performance models

FRAPCON and FRAPTRAN are the steady-state and transient fuel performance codes, respectively, that are used by the U.S. Nuclear Regulatory Commission (NRC) in performing confirmatory calculations of licensee fuel performance codes and safety analysis methods during the review and approval of these codes and methods for light-water reactors. The NRC also uses these codes to perform calculations to direct regulatory research and to assist in the development of new regulations and regulatory guides. FRAPCON and FRAPTRAN are well-validated fuel performance codes that are kept in a constant state of maintenance. FRAPCON and FRAPTRAN have an extensive database of separate effects data used to validate individual material property and fuel performance models and an integral effects database used to assess the overall code prediction within the full range of fuel operations. The key code predictions that are of regulatory interest as they relate to various specified acceptable design limits are: fuel and cladding temperature, rod internal pressure, cladding hoop strain, cladding corrosion and hydriding, and fission gas release. To assess the ability of the code to accurately predict these values, the integral assessment database consists of measurements of fuel centerline temperature, fission gas release, void volume, cladding corrosion, and cladding hoop strain. This paper will discuss the activities that are performed to ensure that FRAPCON and FRAPTRAN represent the state of the industry and will describe the separate effect and integral effect databases that are used to validate the models and are continually being expanded to ensure validation over the full range of fuel operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation Examinations of High Burnup PWR Rods - 18456

The High Burnup Spent Fuel Data Project (herein referred to as the 'project'), sponsored by the US Department of Energy (DOE) Office of Nuclear Energy (NE), is focused on experimentally evaluating the effects of long-term storage and transportation on high burnup (HBU) (defined as >45 gigawatt days per metric ton uranium) pressurized water reactor (PWR) spent nuclear fuel (SNF) [1]. To support this project, in the fall of 2017, an instrumented bolted-lid cask (project cask) at the North Anna reactor site was loaded with intact, HBU PWR fuel assemblies (project assemblies) having four different kinds of cladding and will be reopened in approximately 10-years for inspection. To support pre- and post-storage SNF rod characterization, 25 'sister rods' that are similar to the rods being stored in the project cask were extracted from seven different fuel assemblies at the North Anna nuclear power plant for post-irradiation examination (PIE). The sister rod testing program has multiple objectives, including: 1) Baseline testing to provide essential information on the physical condition and properties of the cladding and the fuel in the cladding prior to the loading, drying, and long-term dry storage process (analogous to an experiment control group). Similar tests are expected to be performed at the end of the 10-year storage period on rods extracted from the cask to identify any changes in the properties of the fuel rods that may have occurred during the dry storage period; and 2) Tests to provide material property and physical data using accelerated separate effects tests (SETs) and small-scale tests (SSTs) to explore a wide range of conditions that may occur for other dry storage systems and/or while the fuel is being transported after aging. Testing will be focused on understanding overall SNF rod strength and durability, and be comprised of both composite fuel and defueled clad testing with a focus on measuring cladding material and mechanical properties. Nondestructive testing is currently underway and plans are being updated to support the initial set of destructive tests that are expected to begin by early 2018. While the data generated can be used for multiple purposes, a primary goal of the sister rod PIE data and associated measured mechanical properties are expected to support existing fuel storage licensing and relicensing activities by addressing identified knowledge gaps, and enhance the technical bases for post-storage transportation, handling, and consolidation activities [1]. This paper presents results obtained from the sister rod testing to date, and describes some of the planned measurements, equipment, and procedures that will be implemented for the initial set of destructive examinations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Radial Heat Flow Apparatus for Thermal Conductivity Characterisation of Cylindrical Samples

During the last two decades, silicon carbide based ceramic composites (SiC/SiC) have become a candidate material for nuclear fuel cladding, first for advanced nuclear systems, such as the GFR, and recently also as potential replacement material for nuclear fuel cladding in light water reactors. This work is contributing to the General Atomics/Westinghouse led CARAT project. In this frame, the thermal conductivity (TC) of cladding prototype sections are measured both before and after neutron irradiation with the purpose of better understanding the effects of neutron irradiation on the pyrolytic carbon interphase linking the SiC fibres to the SiC matrix. To this end, an apparatus has been designed and built to measure the TC of short cylindrical samples, whose lengths range from 5 to 20 cm, by the radial heat flow method. To avoid oxidation issues, the experiments are carried out in vacuum. Today the most common measurement method used to characterise the TC of materials is the so-called laser-flash technique, whereby a short high intensity laser pulse is shot on one surface of a thin flat sample and the energy transfer through the sample is analysed on the other side. Though much faster and easier to implement than the apparatus presented in this work, laser-flash equipment does have issues when dealing with highly anisotropic materials or capturing shape effects such as those present in large aspect ratio samples such as cladding tube sections. The two aforementioned effects are exactly what the developed equipment has been built to capture. The radial heat flow method is based on the principle of measuring the temperature difference building up through a piece of material as this material acts as a thermal resistance against a known heat flow crossing it. This paper presents a new implementation of one of the classical thermal conductivity measurement techniques. Since the development of the laser-flash method in the sixties, steady-state measurements such as the radial heat flow have fallen in disuse. In this discussion, it is shown that a direct measurement method can be used and even be preferable in the case of highly anisotropic materials such as SiC/SiC composites. The advantage of this experimental setup is that the actual transverse conductivity is obtained, whereas laser-flash measurements yield a response in which both the transverse and axial conductivities are mixed. Further steps of this study will include the measurements of samples irradiated with neutrons in the MITR test-reactor. The aim will be to evidence the role played by the pyrolytic carbon interphase by linking the TC measurements with energy filtered electron microscopy. We would like to acknowledge General Atomics and Westinghouse for their support in the frame of the CARAT research program. Providing us with actual prototype clad sections is a unique opportunity. Furthermore the Swiss CCEM.ch project MeAWaT is acknowledged for partially financing the development of the measurement device. (authors)

36 MATERIALS SCIENCE↗

Small-Angle Neutron Scattering Measurements of the δ Deuteride Phase in Zircaloy 4

Hydrogen pickup by Zr-based LWR fuel cladding during service leads to the formation of circumferential hydride platelet particles embedded within the Zr matrix. The precipitation of the hydride phase occurs preferentially on the water-side due to the temperature gradient within the clad wall. The non-uniform hydride morphology is known as a rim structure. Significant tensile hoop stresses within the clad wall develop during the fuel lifetime due to fission gas release and pellet-clad mechanical interaction. One potential post-service cladding failure mechanism is delayed hydride cracking (DHC) initiated by hydride reorientation under this tensile hoop stress. As a consequence, hydride reorientation and DHC have been extensively studied over the last few decades to understand the interdependencies of tensile stress, temperature, hydride morphology, and hydrogen concentration. Much of the most recent work in this area has taken advantage of 3. generation synchrotron X-ray sources to perform in situ measurements of hydride phase stability. Neutron scattering based techniques offer unique advantages in the study of hydrogen in metals (typically with deuterium substituted for hydrogen) but are under utilized in the study of hydrides in Zr. We present small-angle neutron scattering (SANS) measurements of the deuteride phase in Zircaloy 4 (Zy4) here. The SANS measurements presented here demonstrate the sensitivity of the technique to deuteride phase particles embedded in a Zy4 matrix. Quantifiable net scattering at 50 wppm effective hydrogen concentration is derived from a subtraction of a reference sample. This demonstrates that the strong χ phase Porod scattering can be effectively eliminated, revealing the response from the deuteride phase. A similar experimental protocol using small-angle X-ray scattering (SAXS) would likely fail due to poor contrast between the hydride phase and the Zr matrix. Stated in different terms, the SAXS response would be dominated by SPP Porod scattering with unresolvable net scattering from hydride particles. (authors)

36 MATERIALS SCIENCE↗

Fabrication of New NFA-SiC Composites for Nuclear Applications

Cladding materials play the critical and fundamental function of fuel confinement during the safe operation of a nuclear power system. With the development of a new generation of nuclear reactors, investigation of the corresponding advanced cladding materials is attracting intensive scrutiny. Nanostructured ferritic alloy (NFA), which has excellent irradiation resistance and mechanical performance, is one primary candidate for future fission and fusion reactors. The NFA alloys are composed of nano-grained Fe-Cr alloy domains and Y-Ti-O-Cr-Fe enriched nano-clusters. The nano-clusters can not only prevent dislocation glide, grain growth, and grain boundary slip, but also act as sinks to trap helium atoms and radiation-generated point defects. In addition, NFAs can provide high temperature strength and prominent thermal stability, which are beneficial to nuclear cladding applications. Silicon carbide (SiC) is another nuclear cladding candidate. Due to its physical and chemical stability, it shows very good refractory properties at high temperatures up to 2000 deg. C, which has enabled its wide applications in combustion chamber and aerospace engines. In addition, SiC has the remarkable characteristic of radiation stability. SiCf/SiC composite has been developed as an alternative cladding material to metallic alloys. Theoretical simulation is also being developed to understand irradiation induced defects in SiC. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pressure Loading with In-Situ Permeability Measurement of SiC Ceramic Matrix Composite Tube

Silicon carbide fiber in a silicon carbide matrix composite (SiC-SiC) has been actively researched as a potential structural material to be used in advanced high temperature gas reactors (HTGR) and as an accident tolerant cladding material for light water reactors (LWR). This ceramic composite material demonstrates desirable properties for use in nuclear reactor core that include retention of strength from ambient to LWR and HTGR operating and accident temperatures and stability under neutron radiation. However, the ceramic composite material must be designed to meet all the necessary, application driven requirements before it could be implemented in a reactor design. As one of the requirements for a fuel cladding material, the composite has to maintain high level of impermeability as to retain fission gases throughout the fuel cycle. General Atomics (GA) had previously reported results on permeability levels obtained by CVI produced SiC-SiC composites. It has been determined that for LWR size cladding tube that is 51 mm long the permeability allocation equivalent to currently used claddings is 7.3 E-10 atm*cc/sec. With high level of attention to possible sources of leaks in a test setup, it has been demonstrated that a CVI SiC-SiC composites produced by GA can achieve a leak rate of 1 E-12 atm*cc/sec, and therefore it meets the permeability allocation for a fuel cladding. Further study showed that a particular SiC-SiC composite tube can remain impermeable after being pressure loaded well above LWR normal operating conditions. In the study done by Deck et al., hoop stress was applied to a composite tube using pressure load on the inside surface in a load-unload stepwise sequence with increasing maximum applied stress at each step and measuring permeability between steps. The tested composite comprised of 70% thickness of SiC-SiC composite which provides fracture toughness and bears a majority of the applied stress and a 30% thickness of monolithic SiC layer on the outside surface to provide an impermeable barrier. The composite remained impermeable up to internal pressure of 56 MPa which is more than 2.5 times greater than a typical pressure at the end of life in a fuel rod.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Volatility Studies of Lanthanide Hexafluoroacetylacetone Chelates

The Advanced Fuels Campaign within the Fuel Cycle Research and Development program of the Department of Energy (DOE) Office of Nuclear Energy is currently investigating a number of advanced nuclear fuel cladding concepts to improve the accident tolerance of light water reactors (LWRs). Some of the leading candidates to replace traditional zirconium-based cladding are alumina-forming ferritic alloys (e.g., FeCrAl) and silicon carbide (SiC) composites. Oak Ridge National Laboratory has developed experimental designs to irradiate thin-walled cladding tubes with representative geometry in the High Flux Isotope Reactor (HFIR) under relevant LWR temperatures and in some cases under prototypic heat flux. These designs allow for post-irradiation examination (PIE) of cladding which closely resembles expected commercially viable geometries and microstructures. PIE will include studies of dimensional change, microstructure variation, mechanical performance, etc. The experiments were designed using relatively inexpensive rabbit capsules for the irradiation vehicle. The simplistic designs combined with the extremely high neutron flux in the HFIR allow for rapid testing of a large test matrix, thus reducing the time and cost for moving advanced cladding materials closer to commercialization. This work describes the capsule designs that have been developed at ORNL, some initial results, and plans for future irradiations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improvements to Modeling Capabilities of ATF Concepts in the BISON Fuel Performance Code

Research into accident tolerant materials for the fuel and cladding in Light Water Reactors has been at the forefront of the nuclear fuel research community since the events that occurred at the Fukushima Daiichi nuclear power plant in March 2011. Accident tolerant materials are defined as those that provide significantly increased response time in the event of an accident while providing similar or improved performance as the conventional UO{sub 2}/zirconium-based cladding fuel rods during normal operation. In particular, qualitative attributes for materials with enhanced accident tolerance include improved reaction (e.g., oxidation) kinetics with steam, resulting in lower hydrogen (or other combustible gases) generation rate, while maintaining acceptable thermo-mechanical properties, fuel-clad interactions, and fission-product behavior. Through it's Office of Nuclear Energy, the United States Department of Energy (U.S. DOE) has accelerated research in this area through the Fuel Cycle Research and Development (FCRD) Advanced Fuels Campaign (AFC). The goal of the AFC Accident Tolerant Fuel (ATF) program is to guide selection of promising concepts for insertion into a commercial reactor as part of a lead test rod or assembly in 2022. Given the aggressive development schedule, it is impossible to perform a comprehensive set of experiments to provide material characterization data. Therefore, the AFC is utilizing computational analysis tools in an effort to understand the proposed accident tolerant materials. The two materials of interest in this work are iron-chromium-aluminum (FeCrAl) cladding and U{sub 3}Si{sub 2}. From a fuel performance standpoint, the correlations available to describe the behavior of these two materials is limited. Therefore, as additional experimental data becomes available and correlations are updated, the fuel performance models must be updated as well to assure that the material models reflect the latest experimental findings. In this paper we demonstrate the importance of utilizing the latest state-of-the-art models for fuel performance simulations by comparing the change in the updated thermal conductivity model for U{sub 3}Si{sub 2} fuel and oxidation model for FeCrAl cladding alloys using the BISON fuel performance code under normal operating conditions. The results indicate that the latest thermal conductivity model for U{sub 3}Si{sub 2} results in fuel centerline temperatures that are on average approximately 3% higher than the previous model. For the oxidation behavior of FeCrAl alloys the new model predicts observable but small oxide thickness (6 μm) compared to the previous model which predicted essentially zero oxide scale formation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methodology of Experiment Design for Improving Transient Critical Heat Flux Model Development

One phenomenon that contributes to nuclear fuel and clad failure mechanisms is the departure from nucleate boiling (DNB). Accident scenarios such as reactivity-initiated accidents (RIAs) provide conditions where the frequency of boiling crisis is much more likely to occur and on much shorter time scales than loss of coolant (LOCA) or loss of flow (LOFA) accidents. Here, boiling crisis in the form of DNB is attributed to transient-induced heat flux values that exceed the critical heat flux (CHF). The resulting effects, such as bubble crowding and eventual dryout, can affect flow boiling heat transfer and compromise the structural integrity of nuclear reactor materials. The focus of the work proposed here lies in developing a rigorous process using out-of-pile testing, under simulated RIA conditions, to determine the transient critical heat flux of cladding materials, without contributions from aforementioned radiation-induced effects that have been observed during in-pile experiments. This study provides a road-map for developing and performing experiments that simulate the power profile and energy deposition aspects of transient events, specific to RIAs, on the laboratory scale. The goal of our project is to observe and measure DNB in an annular flow channel around a single heater rod that is operating and nominal thermal hydraulic conditions of a PWR. It is also an aim of these experiments to determine how to quantify the gap between SS and transient CHF cases, based on state-dependent properties of the cladding material type that is being interrogated. Traditionally, CHF is determined as a combination of four factors: hydraulic diameter, system pressure, mass flow, fluid quality. The authors propose that an additional measureable quantity, which is dependent on the structural properties of the cladding material itself, is partly reasonable for the difference between measured and model-developed CHF values. Using a carefully metered approach will allow for several key concepts to be realized: compensation for transient-based effects to current models for CHF; adaptation of current models for different cladding material types, including Gen-IV concept materials; and implementation of a correction factor to account for both power transient-based and radiation-induced effects on the CHF that have not yet been accounted for.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗