Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Associated Storage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

In situ chamber for studying battery failure using high-speed synchrotron radiography

The investigation of lithium-ion battery failures is a major challenge for personnel and equipment due to the associated hazards (thermal reaction, toxic gases and explosions). To perform such experiments safely, a battery abuse-test chamber has been developed and installed at the microtomography beamline ID19 of the European Synchrotron Radiation Facility (ESRF). The chamber provides the capability to robustly perform in situ abuse tests through the heat-resistant and gas-tight design for flexible battery geometries and configurations, including single-cell and multi-cell assemblies. High-speed X-ray imaging can be complemented by supplementary equipment, including additional probes (voltage, pressure and temperature) and thermal imaging. Together with the test chamber, a synchronization graphical user interface was developed, which allows an initial interpretation by time-synchronous visualization of the acquired data. Enabled by this setup, new meaningful insights can be gained into the internal processes of a thermal runaway of current and future energy-storage devices such as lithium-ion cells.

25 ENERGY STORAGE↗
DOE OSTI2020

High Penetration Power Electronics Grid: Modeling and Simulation Gap Analysis

Increased penetration of power electronics in the grid is happening through development of high-power drives (like in Type 3 or 4 wind turbines, industrial drives, etc.), high-voltage direct current (HVdc) systems, flexible alternating current transmission systems (FACTS), energy storage systems (ESSs), inverter-based renewables like solar and wind, electric vehicle chargers, and other technologies. Ongoing research and development in new power electronic technologies including, but not limited to, solid-state power substations (SSPS), extreme fast charging (XFC), solid-state transformers, and multi-port power electronics that integrate multiple sources/loads will further increase penetration levels. To ensure stakeholders can integrate high penetration of power electronic technologies safely and reliably requires tools and methods to assess and evaluate their impact on the grid. Objectives: This report surveys, assesses, and analyzes commercially available and open-source tools that can support the assessment and evaluation of power electronics in future grids with high penetration levels. The study includes aspects that range from power flow analysis to dynamics evaluation (including hardware-in-the-loop – HIL testing) for such systems. The challenges and gaps associated with the current generation of toolsets available to assess the technical impact of introducing high penetration of power electronics are reported. The method is summarized in Figure ES-1.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

NETL Well Integrity Workshop: Identifying Well Integrity Research Needs for Subsurface Energy Infrastructure

Wells are a critical component of subsurface energy infrastructure. Ensuring the integrity of wells as engineered pathways for the safe extraction, injection, and storage of fluids in the subsurface is key to maximizing the effectiveness and resilience of that infrastructure. Addressing well integrity issues in a technically robust manner that promotes environmental sustainability and social equity is also an important focus of the United States (U.S.) Department of Energy’s (DOE) Office of Fossil Energy and Carbon Management. Industry best practices, regulatory standards, modern monitoring data acquisition and control systems, and decades of research and development have dramatically improved the performance and reliability of wells for hydrocarbon extraction and underground injection in the oil and gas industry. Yet, important innovation is required to improve and ensure well integrity performance in engineered geologic systems where operational environments (fluid composition, temperature, pressure, and/or stress conditions) and long functional life cycles of well systems present unique challenges. Additionally, work is needed to understand and manage the long-term integrity and risks associated with legacy wells—especially those located adjacent to and presenting hazards for new subsurface activity.

02 PETROLEUM↗
DOE OSTI2022

Modeling Yield, Biogenic Emissions, and Carbon Sequestration in Southeastern Cropping Systems With Winter Carinata

Sustainable aviation fuel (SAF) production from lipids is a technologically mature approach for replacing conventional fossil fuel use in the aviation sector, and there is increasing demand for such feedstocks. The oilseed Brassica carinata (known as Ethiopian mustard or simply carinata) is a promising SAF feedstock that can be grown as a supplemental cash crop over the winter fallow season of various annual crop rotations in the Southeast US, avoiding land use changes and potentially achieving some of the soil carbon sequestration and ecosystem service benefits of winter cover crops. However, carinata may require more intensive management than traditional cover crops, potentially leading to additional soil greenhouse gas (GHG) emissions through increased carbon losses from soil tillage and nitrous oxide (N 2 O) emissions from nitrogen fertilizer application. In this work, the 2017 version of the process-based DayCent ecosystem model was used to establish initial expectations for the total regional SAF production potential and associated soil GHG emissions when carinata is integrated as a winter crop into the existing crop rotations across its current suitability range in southern Alabama, southern Georgia, and northern Florida. Using data from academic and industry carinata field trials in the region, DayCent was calibrated to reproduce carinata yield, nitrogen response, harvest index, and biomass carbon-to-nitrogen ratio. The resulting model was then used to simulate the integration of carinata every third winter across all 2.1 Mha of actively cultivated cropland in the study area. The model predicted regional average yields of 2.9–3.0 Mg carinata seed per hectare depending on crop management assumptions. That results in the production of more than two million Mg of carinata seed annually across the study area, enough to supply approximately one billion liters of SAF. Conventional management of carinata led to only modest increases in soil carbon storage that were largely offset by additional N2O emissions. Climate-smart management via adopting no-till carinata establishment or using poultry litter as a nitrogen source resulted in a substantial net soil GHG sink (0.23–0.31 Mg CO 2 e ha -1 y -1 , or 0.24–0.32 Mg CO2e per Mg of seed produced) at the farms where carinata is cultivated.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Non-destructive electrochemical diagnosis of failure mechanisms in aqueous zinc batteries

The early detection of secondary reactions that affect the life and performance of zinc manganese oxide batteries requires a shift from conventional time-consuming and often destructive procedures to rapid lifetime-predictive techniques. In this work, an electrochemical approach is employed to elucidate independent signatures for four common types of failure mechanisms in zinc manganese dioxide (Zn||MnO2) batteries—namely, the loss of zinc inventory, the loss of active material at the cathode, electrolyte depletion, and increased cell impedance. Our findings, specific to coin cell configurations, reveal that each induced failure mechanism can be distinctively modeled and identified based on responses from the rest voltage and columbic-efficiency data for prompt detection. For instance, electrolyte depletion response manifests a distinctive abrupt (>80 %) decrease in columbic efficiency (CE) and charge-rest voltage (Vc) while the discharge-rest voltage remained constant at ~1.3 V. Furthermore, electrolyte rejuvenation of the cell increased the CE to >95 % and restored Vc from ~0.3 to >1.7 V. Recovery experiments and reference performance tests demonstrated consistency between electrochemical descriptors and their associated failure mechanisms. Further, the outcomes of this work provide valuable insights and data models for some of the dominant failure mechanisms present in zinc manganese battery chemistries, which are beneficial to accelerated early-lifetime diagnosis and advancement of Zn batteries development.

25 ENERGY STORAGE↗
DOE OSTI2021

Physical protection regulates microbial thermal responses to chronic soil warming

Climate warming can affect the temperature sensitivity of microbial activity and growth efficiency, possibly explained by changes to microbially unavailable carbon (C) protected within in soil aggregates. Here, we assessed physical protection by crushing macroaggregates (250–2000 μm) and microaggregates (<250 μm) isolated from mineral soils exposed to 27 years of experimental warming (+5 °C). We hypothesized that removal of physical protection would increase microbial activity and reduce C use efficiency (CUE). We found that crushing increased microbial respiration and biomass turnover rate, but did not affect CUE. We also hypothesized that long-term warming would reduce the effect of physical protection on microbial activity, and that physical protection would attenuate microbial temperature sensitivity in heated compared to control soils. We found that long-term warming was associated with a smaller effect of physical protection for microbial respiration but with a larger effect for biomass turnover rate in macroaggregates. Physical protection reduced the temperature sensitivity of respiration but enhanced the temperature sensitivity of microbial biomass turnover rate in heated compared to control soils. Our work shows that long-term warming has contrasting effects on how microbial respiration, biomass turnover rate, and their thermal responses are mediated by physical protection within soil aggregates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Effects of Applied Interfacial Pressure on Li-Metal Cycling Performance and Morphology in 4 M LiFSI in DME

Lithium-metal anodes can theoretically enable 10x higher gravimetric capacity than conventional graphite anodes. However, Li-metal anode cycling has proven difficult due to porous and dendritic morphologies, extensive parasitic solid electrolyte interphase reactions, and formation of dead Li. We systematically investigate the effects of applied interfacial pressure on Li-metal anode cycling performance and morphology in the recently developed and highly efficient 4 M lithium bis(fluorosulfonyl)imide in 1,2-dimethoxyethane electrolyte. We present cycling, morphology, and impedance data at a current density of 0.5 mA/cm 2 and a capacity of 2 mAh/cm 2 at applied interfacial pressures of 0, 0.01, 0.1, 1, and 10 MPa. Cryo-focused ion beam milling and cryo-scanning electron microscopy imaging in cross section reveal that increasing the applied pressure during Li deposition from 0 to 10 MPa leads to greater than a fivefold reduction in thickness (and therefore volume) of the deposited Li. This suggests that pressure during cycling can have a profound impact on the practical volumetric energy density for Li-metal anodes. A “goldilocks zone” of cell performance is observed at intermediate pressures of 0.1–1 MPa. Increasing pressure from 0 to 1 MPa generally improves cell-to-cell reproducibility, cycling stability, and Coulombic efficiency. However, the highest pressure (10 MPa) results in high cell overpotential and evidence of soft short circuits, which likely result from transport limitations associated with increased pressure causing local pore closure in the separator. All cells exhibit at least some signs of cycling instability after 50 cycles when cycled to 2 mAh/cm 2 with thin 50 μm Li counter electrodes, though instability decreases with increasing pressure. In contrast, cells cycled to only 1 mAh/cm 2 perform well for 50 cycles, indicating that capacity plays an important role in cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2021

Simulation of Hurricane Harvey flood event through coupled hydrologic-hydraulic models: Challenges and next steps

Using the 2017 Hurricane Harvey flood event as a test case, this study set up a series of sensitivity analyses to highlight three challenges associated with large-scale flood inundation modeling, including (a) model parameterization, (b) errors in digital elevation models, and (c) effects of reservoir retention. Driven by radar-based hourly rainfall data, a series of hydrologic-hydraulic models including the VIC hydrologic model, RAPID routing model, and Flood2D-GPU hydrodynamic model are set up over Harris County, Texas, to simulate flood inundation and hazards. The results demonstrate the importance of hydrologic parameters in improving flood modeling. For a large flood event such as Hurricane Harvey, the effect of the initial water depths is insignificant. The Manning's n values may increase the peak water depth by ~1%, the flood extents by 65km 2 , and the high danger zone by ~6%. On the contrary, the bathymetry correction factors may reduce the flood extent by ~1.4% and the high-danger zone by ~4%. Reducing the reservoir storage capacity to 1% may increase the flood extent by ~4% and the high-danger zone by ~17%. This study may provide supporting information to guide and prioritize the development of future high-performance computing hydrodynamic large-scale flood simulations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

An unwanted guest in the electrochemical oxidation of high-voltage Li-ion battery electrolytes: the life of highly reactive protons

Lithium-ion batteries (LIBs) are central to the urgent societal need to decarbonize both transportation and energy storage on the grid. Unfortunately, despite their attractive energy/power density, as well as high coulombic and energy efficiencies, further improvement of this technology – especially their durability – is desperately needed. To support these efforts, our study focuses on fundamental understanding of the decomposition pathways for LIB electrolytes at the cathode–electrolyte interface (CEI), as the nature of these reactions directly controls the extent to which cell capacity and voltage decays in these systems. In this study, we employ electrochemical methods, coupled with product analysis using NMR spectroscopy and mass spectrometry, to determine the decomposition mechanisms in both model and technologically relevant electrolytes. Remarkably, we discovered the electrochemical formation of protons with high chemical activity, comparable to known superacids, at potentials relevant to practical Li-ion batteries. Their reactivity toward every individual component of the CEI provides a unified thermochemical origin for a myriad of side reactions that are commonly associated with the electrochemical reaction. In particular, electrochemically generated protons react with intact EC molecules to form CO 2 and other short and long chain ethers. They also undergo an acid–base reaction with LiPF 6 , to form the weaker acid HF, and with the cathode active material, leaching transition metals into the electrolyte. Collectively, the results of this study all point to the urgent need to either mitigate this proton formation or introduce benign harvesting additives via new electrolyte design strategies.

Ilic, Stefan [Argonne National Laboratory (ANL), A↗
DOE OSTI2021

Cesium Batch Contact Equilibrium Testing of Crystalline Silicotitanate (CST) Sieve Cuts in SRS Average Simulant and Examination of CST Samples Aged in Caustic and Simulant in Support of Tank Closure Cesium Removal 1A (TCCR-1A)

Batch contact testing to determine cesium equilibrium loading on Crystalline Silicotitanate ion exchange media in Savannah River Site Average Waste Simulant at 25 °C indicated that smaller diameter particles isolated by sieving pretreated CST media may load slightly higher (<10%) amounts of cesium, though the differences are within analytical uncertainty. In addition, ion exchange media sub-samples stored in 2-4 M NaOH and caustic simulant solutions for ~2.5 years were examined by optical microscopy and the 3 M NaOH sample was also analyzed to determine whether changes in the particle size distribution occurred during storage. No visual indications of particle attrition or agglomeration were observed for any sample. Particle size analysis indicated that a slight decrease occurred in the average particle diameter following contact with 3 M NaOH (541 µm average diameter versus 566 µm for the pretreated CST prior to contact). A small increase (from 0 to <0.5 wt. %) in the number of particles ranging from 271 and 322 µm was also observed for the CST sample contacted with 3 M NaOH relative to a sample of the original pretreated material. However, this small change could be due to sub-sampling differences or analytical uncertainty. It does not appear that small particles are formed to a significant degree during CST caustic contact or that small particles which do form (presumably from attrition of larger particles during pretreatment) load significantly more cesium than the bulk material. Minimal other negative consequences were observed associated with CST extended caustic or simulant contact, except for the tendency for more concentrated salt solutions to form some salt crystals which deposit on the media over time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Solar and Wind Forecast Error Reserve Sharing in a Multi-Utility Region

As electricity systems transition to higher levels of solar and wind generation, electric system operators will likely need to hold additional reserves to manage the forecast error associated with these resources. Because wind and solar forecast errors tend to be poorly correlated across space, system operators can reduce their reserve requirements by sharing reserves. This paper examines the value of forecast error reserve sharing among balancing areas in the Southeast United States. It finds that forecast error reserve requirements increase linearly with growth in solar and wind generation capacity but that reserve sharing can significantly reduce physical (MW) reserve requirements (from 25%-26% to 18%-19% of average load in high solar scenarios). It finds that the value of forecast error reserve sharing declines with higher levels of solar and wind generation, due to lower wholesale energy and reserve prices. Even with declines in wholesale prices, forecast error reserve sharing can still provide substantial value (as much as $\$$400 million per year in a high solar scenario), though with higher levels of solar, wind, and electricity storage, this value is increasingly tied to avoiding scarcity prices. The results suggest the importance of coordinated capacity expansion planning for forecast error reserve sharing.

14 SOLAR ENERGY↗
DOE OSTI2023

N2-to-NH3 conversion by excess electrons trapped in point vacancies on 5f-element dioxide surfaces

Ammonia (NH 3 ) is one of the basic chemicals in artificial fertilizers and a promising carbon-free energy storage carrier. Its industrial synthesis is typically realized via the Haber−Bosch process using traditional iron-based catalysts. Developing advanced catalysts that can reduce the N 2 activation barrier and make NH 3 synthesis more efficient is a long-term goal in the field. Most heterogeneous catalysts for N 2 -to-NH 3 conversion are multicomponent systems with singly dispersed metal clusters on supporting materials to activate N 2 and H 2 molecules. Herein, we report single-component heterogeneous catalysts based on 5 f actinide dioxide surfaces (ThO 2 and UO 2 ) with oxygen vacancies for N 2 -to-NH 3 conversion. The reaction cycle we propose is enabled by a dual-site mechanism, where N 2 and H 2 can be activated at different vacancy sites on the same surface; NH 3 is subsequently formed by H − migration on the surface via associative pathways. Oxygen vacancies recover to their initial states after the release of two molecules of NH 3 , making it possible for the catalytic cycle to continue. Our work demonstrates the catalytic activities of oxygen vacancies on 5 f actinide dioxide surfaces for N 2 activation, which may inspire the search for highly efficient, single-component catalysts that are easy to synthesize and control for NH 3 conversion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microwave-Based Synthesis of Functional Morphological Variants and Carbon Nanotube-Based Composites of VS 4 for Electrochemical Applications

A novel facile, fast, and efficient microwave-assisted method was developed to synthesize a number of diverse nanostructured motifs (ranging from nanorods to nanoflowers) of VS 4 along with its associated composite heterostructures, VS 4 /multi-walled carbon nanotube (MWNT; i.e., multi-walled carbon nanotubes). Specifically, we have probed and correlated the effects of a number of specific experimental variables, including primarily precursor, solvent, temperature, and time. We noted that nanorods formed more readily with VO(acac) 2 as the vanadium precursor and n-methyl-2-pyrrolidone (NMP) as a polar reaction solvent. By contrast, we determined that hierarchical three-dimensional (3D) nanoflower-like assemblies, ranging in size from 100 to 200 nm in average diameter, could be controllably synthesized by using Na 3 VO 4 as the vanadium precursor and an aqueous water: polar solvent mixture as the reaction medium. We also observed that VS 4 disintegrates, when in the presence of either air, solution, or a combination of these environments, and established that the extent of VS4 nanorod decomposition could be almost fully prevented by storage under nitrogen. From an application’s perspective, our VS 4 is electrochemically active and shows behavior, consistent with the literature. In particular, as compared with pristine VS 4 nanorods alone, we observed enhanced electrochemical activity with (i) 3D hierarchical flower-like motifs, (ii) unique necklace-like VS 4 nanorod–MWNT composites, and (iii) samples in which as-prepared VS4 nanorods had been annealed. Moreover, we found that the rational application of specific physical and chemical processing treatments, such as (i) thermal annealing to improve crystallinity, (ii) the addition of MWNTs to form conductive composites, and (iii) the evolution of morphology from one-dimensional (1D) nanorods to more complex 3D nanoflowers, was favorable to the resulting electrochemical performance with respect to increasing stability and reversibility.

25 ENERGY STORAGE↗
DOE OSTI2023

Clean Energy Microgrids: Considerations for State Energy Offices and Public Utility Commissions to Increase Resilience, Reduce Emissions, and Improve Affordability

In fall 2019, the National Association of Regulatory Utility Commissioners (NARUC) and the National Association of State Energy Officials (NASEO) initiated a joint Microgrids State Working Group (MSWG), funded by the U.S. Department of Energy (DOE) Office of Electricity (OE). The MSWG aims to bring together NARUC and NASEO members to explore the capabilities, costs, and benefits of microgrids; discuss barriers to microgrid development; and develop strategies to plan, finance, and deploy microgrids to improve resilience. This report, Clean Energy Microgrids: Considerations for State Energy Offices and Public Utility Commissions to Increase Resilience, Reduce Emissions, and Improve Affordability, focuses specifically on how clean energy microgrids can achieve both resilience and clean energy benefits. The paper provides an overview of the challenges faced by clean energy microgrids, outlines benefits that clean energy microgrids can provide, and details economic and cost considerations for the development of clean energy microgrid projects. Outlined in the paper are the necessary technological components of a clean energy microgrid, including generation, storage, energy efficiency measures, and smart controls. Current technologies are highlighted, along with potential configurations of clean technologies that are approaching cost competitiveness with commercially available options. The paper concludes with both policy and regulatory considerations for State Energy Offices and Public Utility Commissions to enhance the development and deployment of clean energy microgrids. Although it touches on the clean energy microgrids’ role in integrating distributed energy resources (DERs) into the larger grid, this is not the focus of this paper.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Thermal and Electrical Properties of Isocyanate Derived Organic Aerogels for Cryogenic Insulation Applications

The use and storage of cryogens such as liquefied nitrogen, helium, hydrogen among others requires reliable and efficient thermal insulation systems. Passive insulation from high performance materials that are well-known for their inherent low thermal conductivity would reduce the overall costs involved in design, manufacture and maintenance of such systems. One such class of materials are referred to as aerogels. These materials are known for their low density, high mesoporosity, high surface areas, low thermal conductivity and high acoustic impedance. Aerogels were invented by S.S. Kistler in 1931 and the most common type are those made of silica. However, the inherent fragility of silica aerogels makes them hard to mass produce, and therefore applications have been limited. A major breakthrough was introduced by our team almost 20 years ago with the invention of polymer crosslinked silica aerogels. Those materials shifted attention to all-polymer aerogels that have overcome all fragility issues associated with their inorganic counterparts. This study focuses on such polymeric aerogels that can be mass produced as large monoliths while maintaining the low thermal conductivity of traditional silica aerogels over a wide temperature range. Manufacturing flexibility of polymeric aerogels allows fabrication of blocks and sheets that can be applied in various configurations to insulate cryogenic and superconducting devices. The thermal conductivity with 80 K and room temperature boundary are reported as well as other properties (electrical), that need to be considered when designing devices for cryogenic applications.

Churu, Gitogo↗
DOE OSTI2026

EASY-SHIFT v Alpha

The software is a generic, price- and load-responsive control algorithm integrating heat pumps with thermal energy storage. The algorithm leverages simple models of the system and easily accessible data to schedule operation of heat pumps and thermal energy storage in ways that minimize the cost of operating the heating/cooling system. This tool is specifically designed to be easy to interact with, and something that industry partners are able to adopt. There are two current state of the art approaches. Industry tends to develop very simple algorithms, with predetermined schedules that are not capable of changing operation in response to changes in operating environment. For example, a control designed to avoid high-price electricity from 5-8 PM will not be able to adapt if the high-price period changes to 4-9 PM. Academia commonly develops algorithms called Model predictive control (MPC). MPC requires extensive data and highly trained staff to develop a specific type of simulation model of the building, connect the building to optimization algorithms, and leverage powerful computers. Industry, with limited time/finance budgets for any project, is resistant to adopting MPC due to the associated high complexity and cost.

Grant, Peter [Lawrence Berkeley National Laborator↗
DOE OSTI2025

Dynamic Capacitive Wireless Power Transfer System for Electric Vehicles (CRADA Final Report)

Road transportation accounts for 23% of our nation's total energy consumption, 59% of our petroleum consumption and 22% of our total emissions. Electric vehicles (EVs) have much higher well-to-wheel efficiency compared to gasoline vehicles and can reduce our dependence on oil, minimize emissions, improve local air quality and provide a platform for technological innovation and economic growth. While major progress has been made in the development of electric vehicles, their penetration remains under 1 The main hurdles in their widespread adoption are high cost, limited range and long charging times, due to limitations in battery technology. An approach to overcome these hurdles is to substantially reduce the on-board energy storage and instead deliver power wirelessly to the vehicle while it is in motion dynamic wireless power transfer (WPT). For EV charging applications, researchers have traditionally focused on inductive WPT. An issue with inductive WPT systems is that for magnetic flux guidance and shielding, they require ferrite cores, making them expensive, bulky and difficult to embed in the roadway. Under an ARPA-E IDEAS grant, the CU Boulder team has recently developed an alternative approach to WPT based on capacitive coupling that is much smaller, lighter, less expensive, and easier to embed in the roadway than inductive WPT; and have demonstrated a 1.2-kW 6.78-MHz version of this capacitive WPT system on a stationary platform. Under this seed grant program, preliminary work will be carried out on a dynamic capacitive WPT system to prepare a strong proposal for the ARPA-E OPEN 2018 FOA.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Tuned Reactivity at the Lithium Metal–Argyrodite Solid State Electrolyte Interphase

Thin intermetallic Li 2 Te–LiTe 3 bilayer (0.75 µm) derived from 2D tellurene stabilizes the solid electrolyte interphase (SEI) of lithium metal and argyrodite (LPSCl, Li 6 PS 5 Cl) solid-state electrolyte (SSE). Tellurene is loaded onto a standard battery separator and reacted with lithium through single-pass mechanical rolling or transferred directly to SSE surface by pressing. State-of-the-art electrochemical performance is achieved, e.g., symmetric cell stable for 300 cycles (1800 h) at 1 mA cm -2 and 3 mAh cm -2 (25% DOD, 60 µm foil). Cryo-stage focused ion beam (Cryo-FIB) sectioning and Raman mapping demonstrate that the Li 2 Te–LiTe 3 bilayer impedes SSE decomposition. The unmodified Li–LPSCl interphase is electrochemically unstable with a geometrically heterogeneous reduction decomposition reaction front that extends deep into the SSE. Decomposition drives voiding in Li metal due to its high flux to the reaction front, as well as voiding in the SSE due to the associated volume changes. Analysis of cycled SSE found no evidence for pristine (unreacted) lithium metal filaments/dendrites, implying failure driven by decomposition phases with sufficient electrical conductivity that span electrolyte thickness. In conclusion, DFT calculations clarify thermodynamic stability, interfacial adhesion, and electronic transport properties of interphases, while mesoscale modeling examines interrelations between reaction front heterogeneity (SEI heterogeneity), current distribution, and localized chemo-mechanical stresses.

25 ENERGY STORAGE↗