Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Thermochemical Kinetics for Multireference Systems: Addition Reactions of Ozone

The 1,3-dipolar cycloadditions of ozone to ethyne and ethene provide extreme examples of multireference singlet-state chemistry, and they are examined here to test the applicability of several approaches to thermochemical kinetics of systems with large static correlation. Four different multireference diagnostics are applied to measure the multireference characters of the reactants, products, and transition states; all diagnostics indicate significant multireference character in the reactant portion of the potential energy surfaces. We make a more complete estimation of the effect of quadruple excitations than was previously available, and we use this with CCSDT/CBS estimation of Wheeler et al. (Wheeler, S. E.; Ess, D. H.; Houk, K. N. J. Phys. Chem. A 2008, 112, 1798.) to make new best estimates of the van der Waals association energy, the barrier height, and the reaction energy to form the cycloadduct for both reactions. Comparing with these best estimates, we present comprehensive mean unsigned errors for a variety of coupled cluster, multilevel, and density functional methods. Several computational aspects of multireference reactions are considered: (i) the applicability of multilevel theory, (ii) the convergence of coupled cluster theory for reaction barrier heights, (iii) the applicability of completely renormalized coupled cluster methods to multireference systems, (iv) the treatment by density functional theory, (v) the multireference perturbation theory for multireference reactions, and (vi) the relative accuracy of scaling-type multilevel methods as compared with additive ones. It is found that scaling-type multilevel methods do not perform better than the additive-type multilevel methods. Among the 48 tested density functionals, only M05 reproduces the best estimates within their uncertainty. Multireference perturbation theory based on the complete-active-space reference wave functions constructed using a small number of reaction-specific active orbitals gives accurate forward barrier heights; however, it significantly underestimates reaction energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Manganese Addition to the Co-MCM-41 Catalyst in the Selective Synthesis of Single Wall Carbon Nanotubes

The effect of manganese addition to the Co-MCM-41 catalyst on the synthesis of single wall carbon nanotubes (SWNT) by CO disproportionation was characterized. The ratio between the two metals in the MCM-41 framework was varied, and its effect on the resultant SWNT distribution was studied and compared with the results obtained for the monometallic Co-MCM-41 catalyst. Methods including temperature-programmed reduction, X-ray absorption fine structure, thermogravimetric analysis, TEM imaging, and Raman and fluorescence spectroscopy were employed to characterize the behavior of the catalysts under the SWNT synthesis conditions and the diameter and structure distribution of the resultant nanotubes. We found that addition of Mn to the Co-MCM-41 catalyst promotes the growth of SWNT, leading to synthesis of high yield, small diameter SWNT. Manganese does not act in the nucleation of SWNT but acts as an anchoring site for cobalt particles formed during the synthesis process as shown by X-ray absorption.

36 MATERIALS SCIENCE↗

Evaluation of Tellurium as a Fuel Additive in Neodymium-Containing U-Zr Metallic Fuel

Phase-stability in a U-Zr-Te-Nd multi-component metallic fuel for advanced nuclear reactors is systematically investigated by taking into account binary, ternary and quaternary interactions between elements involved. Historically, the onset of fuel-cladding chemical interactions (FCCI) greatly limits the burnup potential of U-Zr fuels primarily due to interactions between lanthanide fission products and cladding constituents. Tellurium (Te) is evaluated as a potential additive for U-Zr fuels to bind with lanthanide fission products, e.g. neodymium (Nd), negating or mitigating the FCCI effect. Potential fresh fuel alloy compositions with the Te additive, U-Zr-Te, are characterized. Te is found to completely bind with Zr within the U-Zr matrix. Alloys simulating the formation of the lanthanide element Nd within U-Zr-Te are also evaluated, where the Te-Nd binary interaction dominates and NdTe is found to form as a high temperature stable compound. The experimental observations agree well with the trends obtained from density functional theory calculations. According to the calculated enthalpy of mixing, Zr-Te compound formation is favored in the U-Zr-Te alloy whereas NdTe compound formation is favored in the U-Zr-Te-Nd alloy. Further, the calculated charge density distribution and density of states provide sound understanding of the mutual chemical interactions between elements and phase-stability within the multi-component fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermographic Microstructure Monitoring in Electron Beam Additive Manufacturing

To reduce the uncertainty of build performance in metal additive manufacturing, robust process monitoring systems that can detect imperfections and improve repeatability are desired. One of the most promising methods for in-situ monitoring is thermographic imaging. However, there is a challenge in using this technology due to the difference in surface emittance between the metal powder and solidified part being observed that affects the accuracy of the temperature data collected. This developed a method for properly calibrating temperature profiles from thermographic data and then determining important characteristics of the build through additional processing. The thermographic data was analyzed to determine the transition of material from metal powder to a solid as-printed part. A corrected temperature profile was then assembled for each point using calibrations for these surface conditions. Using this data, we calculated the thermal gradient and solid-liquid interface velocity and correlated it to microstructural variation within the part experimentally. This work shows that by using a method of process monitoring, repeatability of a build could be monitored specifically in relation to microstructure control.

36 MATERIALS SCIENCE↗

Understanding Flow Characteristics in Metal Additive Manufacturing

In fluid flow, the frictional effects from interior surfaces of flow components create pressure loss across the surface. Understanding this inherent pressure loss due to friction and other phenomena is important when designing a flow system. For conventional manufacturing, friction loss has been empirically studied and is well known in the engineering community. However, newer manufacturing techniques, such as laser powder bed fusion (LPBF), an additive manufacturing technique, need to be understood. The inherent flow conditions resulting from the additive processes were studied. Test samples were printed with the flow path oriented in the vertical direction with different channel diameters to characterize the inherent fundamental flow properties of the process. Moody diagrams were replicated for a greater understanding of possibilities and shortfalls when implementing LPBF into design applications. Experimental flow testing revealed that greater effective sand grain roughness resulted from this process when compared to conventional machining methods. This roughness did not correlate well to the average roughness measured with a laser scanning microscope but was consistent with the average particle size of the powder metal feedstock.

42 ENGINEERING↗

Role of Y{sub 2}O{sub 3}, CaO, MgO additives on structural and microstructural behavior of zirconia/mullite aggregates

Zirconia mullite (MUZ), Y{sub 2}O{sub 3}-MUZ, CaO-MUZ and MgO-MUZ composites, synthesized through plasma fusion technique, are becoming important due to their commercial scale of production within five minutes of plasma treatment from sillimanite, zircon and alumina mixture. The X-ray diffraction studies reveal the monoclinic zirconia phase in MUZ composite whereas mixed monoclinic, tetragonal and cubic phases of zirconia have been observed in Y{sub 2}O{sub 3}, CaO, MgO added MUZ composites. The Y{sub 2}O{sub 3}, CaO and MgO additives act as sintering aids to favour the transformation and stabilisation of tetragonal and cubic zirconia phases at room temperature. These additives also play a key role in the development of various forms of microstructure to achieve dense MUZ composites.

36 MATERIALS SCIENCE↗

Theoretical investigation of the effect of hydrogen addition on the formation and properties of soliton in direct current argon plasma

In this study the effect of hydrogen addition on the formation and properties of soliton in direct-current (DC) argon plasma is theoretically investigated. By coupling fluid equations with Poisons equation for such multi-component plasma, the Mach number and amplitude of the soliton are determined following pseudo potential method. Addition of hydrogen in argon discharge leads to the decrease of electron, Ar{sup +} ion density while a reverse trend was observed for ArH{sup +} and hydrogen like ions. It was found that presence of hydrogen like ions in argon plasma affects the formation of soliton with its amplitude significantly decreases as concentration of hydrogen increases. On the other hand, increase in ion to electron temperature ratios of the lighter ions in the discharge also has a significant influence on the amplitude and formation of soliton. The inverse relation between solitons width and amplitude is found to be consistent for the entire range of study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improvement of mechanical properties by additive assisted laser sintering of PEEK

The additive assisted laser sintering was recently developed at IKT: A carbon black (CB) additive is used to adjust the polymer's laser absorption behavior with the aim to improve the interconnection of sintered powder layers. In this paper a parameter study, Polyetheretherketone (PEEK) samples were prepared with different contents of carbon black and were laser sintered with varying thermal treatment. The samples were mechanically tested and investigated by optical light and transmission electron microscopy. An influence on the morphology at the border areas of particles and intersections of laser sintered layers was found. Depending on the viscosity of the raw material and CB content, different shapes of lamellae were observed. These (trans-) crystalline or polymorph structures, respectively, influence the thermal and mechanical behavior of the virgin PEEK. Moreover, the thermal treatment during the sintering process caused an improvement of mechanical properties like tensile strength and elongation at break.

36 MATERIALS SCIENCE↗

Compliance and control characteristics of an additive manufactured-flexure stage

This paper presents a compliance and positioning control characteristics of additive manufactured-nanopositioning system consisted of the flexure mechanism and voice coil motor (VCM). The double compound notch type flexure stage was designed to utilize the elastic deformation of two symmetrical four-bar mechanisms to provide a millimeter-level working range. Additive manufacturing (AM) process, stereolithography, was used to fabricate the flexure stage. The AM stage was inspected by using 3D X-ray computerized tomography scanner: air-voids and shape irregularity. The compliance, open-loop resonance peak, and damping ratio of the AM stage were measured 0.317 mm/N, 80 Hz, and 0.19, respectively. The AM stage was proportional-integral-derivative positioning feedback-controlled and the capacitive type sensor was used to measure the displacement. As a result, the AM flexure mechanism was successfully 25 nm positioning controlled within 500 μm range. The resonance peak was found approximately at 280 Hz in closed-loop. This research showed that the AM flexure mechanism and the VCM can provide millimeter range with high precision and can be a good alternative to an expensive metal-based flexure mechanism and piezoelectric transducer.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron beam-generated Ar/N{sub 2} plasmas: The effect of nitrogen addition on the brightest argon emission lines

The effect of nitrogen addition on the emission intensities of the brightest argon lines produced in a low pressure argon/nitrogen electron beam-generated plasmas is characterized using optical emission spectroscopy. In particular, a decrease in the intensities of the 811.5 nm and 763.5 nm lines is observed, while the intensity of the 750.4 nm line remains unchanged as nitrogen is added. To explain this phenomenon, a non-equilibrium collisional-radiative model is developed and used to compute the population of argon excited states and line intensities as a function of gas composition. The results show that the addition of nitrogen to argon modifies the electron energy distribution function, reduces the electron temperature, and depopulates Ar metastables in exchange reactions with electrons and N{sub 2} molecules, all of which lead to changes in argon excited states population and thus the emission originating from the Ar 4p levels.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spall fracture in additive manufactured tantalum

In this work, we present a series of experiments on the response of additive manufactured (AM) tantalum to dynamic loading, specifically the spall strength. Rectangular plates of AM tantalum were produced, with subsequent characterization revealing a highly anisotropic microstructure. Samples were taken from these plates to investigate the effect of anisotropy on the spall strength: the resistance to high strain-rate tensile damage. A conventional, wrought tantalum sample, possessing an equiaxed microstructure, was also tested to serve as a control. Additionally, shock loading was performed via light gas-gun flyer-plate impact experiments, with laser velocimetry on the rear of the samples to record the shock wave profiles and soft-recovery techniques to allow post-mortem analysis. In general, the AM samples were found to have a higher Hugoniot elastic limit, the dynamic yield strength under shock loading, while having a reduced spall strength, when compared to the wrought tantalum samples.

36 MATERIALS SCIENCE↗

Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading

The performance of a high explosive charge is highly influenced by the detonation velocity and any inherent internal structure. Additively manufactured (AM) high explosive charges allow for a precisely engineered internal structure and the selective placement of discrete or graded volumes of a tailored material, which are unachievable by conventional means. The dilution of a solid explosive by an inert additive for detonation velocity reduction is herein evaluated for a method of material extrusion called a direct-ink-write AM, where an 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane-based ultraviolet -curable energetic-binder paste explosive was diluted by the inert density mock 5-iodo-2′-deoxyuridine for use in the manufacture of multi-material explosive charges. The explosive ink was characterized for printing by rheological and particle size measurements, and the detonation velocities for 0–40 wt. % inert diluent were found to have a continuous linear reduction in detonation velocity down to 14.3% difference. A two-component 3D plane wave explosive lens with 8.038 km/s “fast” and 7.491 km/s “slow” diluted ink in an internal cone demonstrated a reduced time of breakout at the output face from 361 to 53 ns. A linearly graded “fast–slow–fast” cylinder was successfully printed and fired, showing engineered control along the length of the charge as the detonation velocity dropped from 7.851 to 6.700 km/s and then recovered to 7.241 km/s. The extreme control over the internal composition of a high explosive charge via a dual-material extruder/mixer challenges conventional manufacturing approaches and opens new avenues for engineered detonation wavefronts, high explosive charge performance, and new applications.

36 MATERIALS SCIENCE↗

Characteristics of yttrium oxide laser ceramics with additives

Neodymium- or ytterbium-doped laser ceramics with a disordered crystal-field structure formed by introduction of iso- and heterovalent elements into yttrium oxide are studied. It is shown that these additives broaden the spectral band of laser transitions, which makes it possible to use ceramics as active laser media emitting ultrashort pulses. Lasing was obtained in several samples of this ceramics. At the same time, it is shown that addition of zirconium and hafnium stimulates the Foerster quenching of upper laser levels and pump levels. (extreme light fields and their applications)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multiscale fatigue crack initiation in hierarchical additively manufactured alloys

Bioinspired hierarchical microstructures offer a route toward engineered fatigue resistance in additively manufactured alloys. However, it remains unclear how discrete structural constituents independently govern damage accumulation, particularly during the critical fatigue initiation regime where short cracks strongly interact with local microstructure. Here, we investigate multiscale fatigue initiation in a dual-phase, nanolamellar AlCoCrFeNi 2.1 high-entropy alloy. By comparing microscale specimens that isolate the nanolamellar structure against macroscale specimens containing the full melt-pool architecture, we identify size-dependent fatigue initiation mechanisms. We find that failure is dictated by nanolamellar interfaces at the microscale, whereas mesoscale melt pool boundaries serve to initiate fatigue at the macroscale. This mechanistic shift is accompanied by a transition from macroscale quasi-brittle failure to microscale plasticity-driven crack extension. Our results provide a physical framework for understanding how structural hierarchy governs the transition from discrete microstructural deformation to continuum fatigue fracture behavior, informing the design of damage-tolerant, additively manufactured alloys.

36 MATERIALS SCIENCE↗

Coolant Channel Design for Additively Manufactured Reactor Cores

Additive manufacturing (AM) methods are currently being explored for applications in nuclear reactors to make advanced reactors more efficient, safe, and reliable. The Transformational Challenge Reactor (TCR) program has explored AM for nuclear by designing a high-temperature gas reactor (HTGR) using an AM silicon carbide fuel form with uranium nitride–tristructural isotropic fuel. In this study, we detail the design process for the TCR fuel form’s coolant channels using computational fluid dynamics models with conjugate heat transfer. Additionally, this work discusses how these models were interfaced with other design teams, project milestones, and the agile design method used to mature the reactor design. The methodology deployed was able to create a channel design with lower maximum fuel temperatures and thermal stresses in the fuel form over traditional channel designs that can be manufactured subtractively. These results were achieved with only small manufacturing penalties. Results are discussed and presented on lessons learned for designing AM components for nuclear reactors. Finally, areas of opportunity are discussed for advanced design tools to further automate design activities and optimize reactors with fewer built-in assumptions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of toolpath in large-format additive manufacturing with bio-derived composites

There has been growing interest in integrating bio-derived composites into Large-format additive manufacturing (LFAM) feedstocks to reduce the use of petroleum-derived materials and reduce the overall carbon footprint of LFAM. However, these materials present unique challenges during manufacturing due to their variability, which can lead to unintended deformations and failures attributable to suboptimal process conditions. While numerical modelling has been extensively employed to simulate numerous manufacturing processes, its application in LFAM with bio-derived composites remains limited. This study addresses this gap by systematically developing a numerical model to simulate the LFAM process using bio-based materials, specifically wood fiber-reinforced polylactic acid (PLA/WF). Experimental investigations were conducted to characterise the thermal and mechanical properties of additively manufactured PLA/WF specimens. Numerical simulations were performed to predict temperature profiles and deformations during LFAM. The effect of varying infill patterns, internal structures, and tool paths on the temperature distribution and deformation of printed parts was explored using the developed model. This article aims to advance the utilisation of bio-derived composites in LFAM systems and provide a comprehensive understanding of the LFAM process. The findings offer valuable insights for optimising process parameters and enhancing the performance of LFAM with bio-based composites.

Large-format additive manufacturing↗

Elastocaloric cooling of additive manufactured shape memory alloys with large latent heat

The stress-induced martensitic phase transformation of shape memory alloys (SMAs) is the basis for elastocaloric cooling. In this paper, we employ additive manufacturing to fabricate TiNi SMAs, and demonstrate compressive elastocaloric cooling in the TiNi rods with transformation latent heat as large as 20 J g -1 . Adiabatic compression on as-fabricated TiNi displays cooling ΔT as high as -7.5 °C with recoverable superelastic strain up to 5%. Unlike conventional SMAs, additive manufactured TiNi SMAs exhibit linear superelasticity with narrow hysteresis in stress–strain curves under both adiabatic and isothermal conditions. Microstructurally, we find that there are Ti 2 Ni precipitates typically one micron in size with a large aspect ratio enclosing the TiNi matrix. Finally, a stress transfer mechanism between reversible phase transformation in the TiNi matrix and mechanical deformation in Ti 2 Ni precipitates is believed to be the origin of the unique superelasticity behavior.

36 MATERIALS SCIENCE↗