Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “#engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

QCSEE under-the-wing engine acoustic data

Both an over-the-wing (OTW) and an under-the-wing (UTW) experimental engine are discussed. The UTW engine had a variable-geometry fan exhaust nozzle and a variable-pitch fan that provided quick-response reverse thrust capability. An automatic digital control enabled optimal engine operation under all steady-state conditions as well as during forward and reverse thrust transient operation. The engine was tested at the Engine Noise Test Facility alone and with wind and flap segments to simulate an installation on a short-haul transport aircraft. The engine acoustic configuration was varied to give 14 test configurations. All of the acoustic test results from the UTW program at Lewis are presented as 1/3-octave-band sound pressure level (SPL) tabulations for all of the test points and some narrow-band spectra and 1/3-octave-band data plots for selected conditions.

Bloomer, H. E.↗
NASA NTRS1981

Heat engine development for solar thermal power systems

The parabolic dish solar collector systems for converting sunlight to electrical power through a heat engine will, require a small heat engine of high performance long lifetime to be competitive with conventional power systems. The most promising engine candidates are Stirling, high temperature Brayton, and combined cycle. Engines available in the current market today do not meet these requirements. The development of Stirling and high temperature Brayton for automotive applications was studied which utilizes much of the technology developed in this automotive program for solar power engines. The technical status of the engine candidates is reviewed and the components that may additional development to meet solar thermal system requirements are identified.

Pham, H. Q.↗
NASA NTRS1982

Ceramic applications in turbine engines

In the past the potential of vehicular gas engines could not be realized because component materials served to limit the turbine operating temperature, thereby restricting fuel economy and initial cost. It was, therefore, not possible for the vehicular gas turbine to compete with more conventional engines. The emergence of low-cost, high-temperature ceramic components has the potential to reverse this situation. For example, the Allison GT404 engine, operating with ceramic components at turbine inlet temperatures up to 2350 F to 2500 F, has the potential of a fuel economy which is better than that of current Diesel engines. The Allison AGT100 engine operating with ceramic components offers the possibility of a 30% improvement in fuel economy over 1985 spark ignition engines. The materials considered for an employment in the ceramic components include silicon carbide, silicon nitride, aluminum silicate, and lithium aluminum silicate.

Byrd, J. A.↗
NASA NTRS1982

NASA ECI programs - Benefits to Pratt and Whitney engines

Proprietary research conducted under the NASA-sponsored Engine Component Improvement program is shown to have advanced the state of such component technologies as thermal barrier coatings, ceramic seal systems, advanced turbine clearance control, and JT9D engine fan design. In addition, the tests conducted have demonstrated the advantages of updated cooling, sealing and aerodynamic designs in the high pressure turbine and compressor of the JT8D engine. These technological advances are being transferred to such novel engine configurations as the PW2037 and NASA Energy Efficient Engine. Attention is given to the results of the thermal coating refinement tests of convectively cooled vanes, and to the development of a single shroud fan design applicable to the JT9D and next-generation engines.

Gaffin, W. O.↗
NASA NTRS1982

The Cummins advanced turbocompound diesel engine evaluation

An advanced turbocompound diesel engine program was initiated to improve the tank mileage of the turbocompound engine by 5% over the vehicle test engines. Engine improvements could be realized by increasing the available energy of the exhaust gas at the turbine inlet, incorporating gas turbine techniques into improving the turbomachinery efficiencies, and through refined engine system optimization. The individual and cumulative performance gains achieved with the advanced turbocompound engine improvements are presented.

Hoehne, J. L.↗
NASA NTRS1983

Automotive Stirling Engine Development Program

Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

Nightingale, N.↗
NASA NTRS1983

Stirling engine design manual, 2nd edition

This manual is intended to serve as an introduction to Stirling cycle heat engines, as a key to the available literature on Stirling engines and to identify nonproprietary Stirling engine design methodologies. Two different fully described Stirling engines are discussed. Engine design methods are categorized as first order, second order, and third order with increased order number indicating increased complexity. FORTRAN programs are listed for both an isothermal second order design program and an adiabatic second order design program. Third order methods are explained and enumerated. In this second edition of the manual the references are updated. A revised personal and corporate author index is given and an expanded directory lists over 80 individuals and companies active in Stirling engines.

Martini, W. R.↗
NASA NTRS1983

Apparatus for improving the fuel efficiency of a gas turbine engine

An energy recovery system is provided for an aircraft gas turbine engine of the type in which some of the pneumatic energy developed by the engine is made available to support systems such as an environmental control system. In one such energy recovery system, some of the pneumatic energy made available to but not utilized by the support system is utilized to heat the engine fuel immediately prior to the consumption of the fuel by the engine. Some of the recovered energy may also be utilized to heat the fuel in the fuel tanks. Provision is made for multiengine applications wherein energy recovered from one engine may be utilized by another one of the engines or systems associated therewith.

Coffinberry, G. A.↗
NASA NTRS1981

Ceramic applications in turbine engines

Development testing activities on the 1900 F-configuration ceramic parts were completed, 2070 F-configuration ceramic component rig and engine testing was initiated, and the conceptual design for the 2265 F-configuration engine was identified. Fabrication of the 2070 F-configuration ceramic parts continued, along with burner rig development testing of the 2070 F-configuration metal combustor in preparation for 1132 C (2070 F) qualification test conditions. Shakedown testing of the hot engine simulator (HES) rig was also completed in preparation for testing of a spin rig-qualified ceramic-bladed rotor assembly at 1132 C (2070 F) test conditions. Concurrently, ceramics from new sources and alternate materials continued to be evaluated, and fabrication of 2070 F-configuration ceramic component from these new sources continued. Cold spin testing of the critical 2070 F-configuration blade continued in the spin test rig to qualify a set of ceramic blades at 117% engine speed for the gasifier turbine rotor. Rig testing of the ceramic-bladed gasifier turbine rotor assembly at 108% engine speed was also performed, which resulted in the failure of one blade. The new three-piece hot seal with the nickel oxide/calcium fluoride wearface composition was qualified in the regenerator rig and introduced to engine operation wiwth marginal success.

Byrd, J. A.↗
NASA NTRS1983

PREWATE: An interactive preprocessing computer code to the Weight Analysis of Turbine Engines (WATE) computer code

The Weight Analysis of Turbine Engines (WATE) computer code was developed by Boeing under contract to NASA Lewis. It was designed to function as an adjunct to the Navy/NASA Engine Program (NNEP). NNEP calculates the design and off-design thrust and sfc performance of User defined engine cycles. The thermodynamic parameters throughout the engine as generated by NNEP are then combined with input parameters defining the component characteristics in WATE to calculate the bare engine weight of this User defined engine. Preprocessor programs for NNEP were previously developed to simplify the task of creating input datasets. This report describes a similar preprocessor for the WATE code.

Fishbach, L. H.↗
NASA NTRS1983

Comparison of Results Obtained from Flight Tests and Simulated Tests of a Digital Electronic Engine Control System in an F-15 Airplane

Substantial benefits of a full authority digital electronic engine control on an air breathing engine were demonstrated repeatedly in simulation studies, ground engine tests, and engine altitude test facilities. A digital engine electronic control system showed improvements in efficiency, performance, and operation. An additional benefit of full authority digital controls is the capability of detecting and correcting failures and providing engine health diagnostics.

Myers, Lawrence P.↗
NASA NTRS1984

CIM's bridge from CADD to CAM: Data management requirements for manufacturing engineering

Manufacturing engineering represents the crossroads of technical data management in a Computer Integrated Manufacturing (CIM) environment. Process planning, numerical control programming and tool design are the key functions which translate information from as engineered to as assembled. In order to transition data from engineering to manufacturing, it is necessary to introduce a series of product interpretations which contain an interim introduction of technical parameters. The current automation of the product definition and the production process places manufacturing engineering in the center of CAD/CAM with the responsibility of communicating design data to the factory floor via a manufacturing model of the data. A close look at data management requirements for manufacturing engineering is necessary in order to establish the overall specifications for CADD output, CAM input, and CIM integration. The functions and issues associated with the orderly evolution of computer aided engineering and manufacturing are examined.

Ford, S. J.↗
NASA NTRS1984

Evaluation of dissociated and steam-reformed methanol as automotive engine fuels

Dissociated and steam reformed methanol were evaluated as automotive engine fuels. Advantages and disadvantages in using methanol in the reformed rather than liquid state were discussed. Engine dynamometer tests were conducted with a four cylinder, 2.3 liter, spark ignition automotive engine to determine performance and emission characteristics operating on simulated dissociated and steam reformed methanol (2H2 + CO and 3H2 + CO2 respectively), and liquid methanol. Results are presented for engine performance and emissions as functions of equivalence ratio, at various throttle settings and engine speeds. Operation on dissociated and steam reformed methanol was characterized by flashback (violent propagation of a flame into the intake manifold) which limited operation to lower power output than was obtainable using liquid methanol. It was concluded that: an automobile could not be operated solely on dissociated or steam reformed methanol over the entire required power range - a supplementary fuel system or power source would be necessary to attain higher powers; the use of reformed mechanol, compared to liquid methanol, may result in a small improvement in thermal efficiency in the low power range; dissociated methanol is a better fuel than steam reformed methanol for use in a spark ignition engine; and use of dissociated or steam reformed methanol may result in lower exhaust emissions compared to liquid methanol.

Lalk, T. R.↗
NASA NTRS1984

Overview of Advanced Stirling and Gas Turbine Engine Development Programs and Implications for Solar Thermal Electrical Applications

The DOE automotive advanced engine development projects managed by the NASA Lewis Research Center were described. These included one Stirling cycle engine development and two air Brayton cycle development. Other engine research activities included: (1) an air Brayton engine development sponsored by the Gas Research Institute, and (2) plans for development of a Stirling cycle engine for space use. Current and potential use of these various engines with solar parabolic dishes were discussed.

Alger, D.↗
NASA NTRS1984

Subatmospheric Brayton-cycle Engine Program Review

A solar energy powered electrical generator utilizing a Subatmospheric Brayton cycle engine is examined. The generator consists of a subatmospheric, Brayton-cycle engine and a permanent magnet (PM) alternator. The electrical power is generated by an alternator driven directly by the Brayton-cycle engine rotating group. Features that enhance reliability and performance include air foil bearings on both the Brayton-cycle engine rotating group and the PM alternator, an atmospheric-pressure solar receiver and gas-fired trim heater, and a high temperature recuperator. The subatmospheric Brayton-cycle engine design is based on that of the gas fired heat pump engine.

Johnson, R. L.↗
NASA NTRS1984

An overview of the NASA rotary engine research program

A brief overview and technical highlights of the research efforts and studies on rotary engines over the last several years at the NASA Lewis Research Center are presented. The test results obtained from turbocharged rotary engines and preliminary results from a high performance single rotor engine were discussed. Combustion modeling studies of the rotary engine and the use of a Laser Doppler Velocimeter to confirm the studies were examined. An in-house program in which a turbocharged rotary engine was installed in a Cessna Skymaster for ground test studies was reviewed. Details are presented on single rotor stratified charge rotary engine research efforts, both in-house and on contract.

Meng, P. R.↗
NASA NTRS1983

Waste heat recovery from adiabatic diesel engines by exhaust-driven Brayton cycles

An evaluation of Bryton Bottoming Systems (BBS) as waste heat recovery devices for future adiabatic diesel engines in heavy duty trucks is presented. Parametric studies were performed to evaluate the influence of external and internal design parameters on BBS performance. Conceptual design and trade-off studies were undertaken to estimate the optimum configuration, size, and cost of major hardware components. The potential annual fuel savings of long-haul trucks equipped with BBS were estimated. The addition of a BBS to a turbocharged, nonaftercooled adiabatic engine would improve fuel economy by as much as 12%. In comparison with an aftercooled, turbocompound engine, the BBS-equipped turbocharged engine would offer a 4.4% fuel economy advantage. If installed in tandem with an aftercooled turbocompound engine, the BBS could effect a 7.2% fuel economy improvement. The cost of a mass-produced 38 Bhp BBS is estimated at about $6460 or 170/Bhp. Technical and economic barriers that hinder the commercial introduction of bottoming systems were identified. Related studies in the area of waste heat recovery from adiabatic diesel engines and NASA-CR-168255 (Steam Rankine) and CR-168256 (Organic Rankine).

Khalifa, H. E.↗
NASA NTRS1983

Baseline performance and emissions data for a single-cylinder, direct-injected diesel engine

Comprehensive fuel consumption, mean effective cylinder pressure, and emission test results for a supercharged, single-cylinder, direct-injected, four-stroke-cycle, diesel test engine are documented. Inlet air-to-exhaust pressure ratios were varied from 1.25 to 3.35 in order to establish the potential effects of turbocharging techniques on engine performance. Inlet air temperatures and pressures were adjusted from 34 to 107 C and from 193 to 414 kPa to determine the effects on engine performance and emissions. Engine output ranged from 300 to 2100 kPa (brake mean effective pressure) in the speed range of 1000 to 3000 rpm. Gaseous and particulate emission rates were measured. Real-time values of engine friction and pumping loop losses were measured independently and compared with motored engine values.

Dezelick, R. A.↗