Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “harmonization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Noise reduction for model counterrotation propeller at cruise by reducing aft-propeller diameter

The forward propeller of a model counterrotation propeller was tested with its original aft propeller and with a reduced diameter aft propeller. Noise reductions with the reduced diameter aft propeller were measured at simulated cruise conditions. Reductions were as large as 7.5 dB for the aft-propeller passing tone and 15 dB in the harmonics at specific angles. The interaction tones, mostly the first, were reduced probably because the reduced-diameter aft-propeller blades no longer interacted with the forward propeller tip vortex. The total noise (sum of primary and interaction noise) at each harmonic was significantly reduced. The chief noise reduction at each harmonic came from reduced aft-propeller-alone noise, with the interaction tones contributing little to the totals at cruise. Total cruise noise reductions were as much as 3 dB at given angles for the blade passing tone and 10 dB for some of the harmonics. These reductions would measurably improve the fuselage interior noise levels and represent a definite cruise noise benefit from using a reduced diameter aft propeller.

Dittmar, James H.↗

The spectral characteristics of rotor blade-vortex interaction noise - Experimental and mathematical results

The BVI impulsive content of a rotor acoustic signal is shown to appear in the mid-frequency range of the power spectrum, between the fifth and thirtieth harmonics of the blade passage frequency, concentrated at the harmonics of the blade passage frequency. These harmonics exhibit a humped or scalloped shape in this mid-frequency spectral region. Increased energy at the harmonics of the shaft frequency appears when the BVI impulsive content demonstrates unsteadiness and blade-to-blade differences in the time domain. A mathematical model of a generalized BVI acoustic signal and its power spectrum shows that the power spectrum is scalloped and filtered by a comb function. The spectrum amplitude is defined by the impulse amplitude and emission time. The scalloping of the spectrum is related to the emission time of the impulse itself, and the spacing of the comb function is related to the repetition time (period) of the impulse. The decay rate of the spectral humps is governed by the inverse of frequency squared. The mathematical model validates the characteristics observed in the data and verify that these characteristics are due to blade-vortex interaction activity.

Martin, Ruth M.↗

Stress and vibraton analyses of anisotropic shells of revolution

An efficient computational strategy is presented for reducing the cost of the stress and free vibration analyses of laminated anisotropic shells of revolution. The analytical formulation is based on a form of the Sanders-Budiansky shell theory including the effects of both the transverse shear deformation and the laminated anisotropic material response. The fundamental unknowns consist of the eight strain components, the eight stress resultants and the five generalized displacements of the shell. Each of the shell variables is expressed in terms of trigonometric functions (Fourier series) in the circumferential co-ordinate, and a three-field mixed finite element model is used for the discretization in the meridional direction. The shell response associated with a range of Fourier harmonics is approximated by a linear combination of a few global approximation vectors, which are generated at a particular value of the Fourier harmonic, within that range. The full equations of the finite element model are solved for only a single Fourier harmonic, and the response corresponding to the other Fourier harmonics is generated using a reduced system of equations with considerably fewer degrees of freedom.

Noor, Ahmed K.↗

Cyclotron scattering lines in gamma-ray burst spectra

If cyclotron scattering, rather than absorption, is responsible for the line features observed recently in two gamma-ray burst spectra (Murakami et al., 1988), then the second and higher harmonics are due to resonant scattering events that excite the electron to Landau levels above the ground state. Here, relativistic Compton scattering cross sections are used to estimate the expected ratio of third to second harmonics in the presence of Doppler broadening. At the field strength (1.7 TG) required to give first and second harmonics at 19 keV and 38 keV, there should be no detectable third harmonic in the spectrum.

Harding, Alice K.↗

Quiet mode for nonlinear rotor models

High frequency harmonics are generated by helicopter rotor systems, and nonlinear blade-element models of these systems create the same harmonics. In discrete real-time rotorcraft simulation, however, especially for handling qualities research, they are more of a nuisance than a benefit. The cycle times required to adequately represent them are rarely obtainable. The result is that distinct frequencies alias into the pilot and simulator bandwidths, thereby decreasing simulation fidelity. However, use of an interpolation procedure permits the observation of harmonics at their proper frequency locations, and an accompanying notch filter may then be used to attenuate the harmonics prior to decimation. Rotorcraft simulations using these techniques are not contaminated with the spurious frequencies that create variable trim points, produce erroneous stability and control derivative data, and obscure time histories.

Mcfarland, R. E.↗

Development of software to improve AC power quality on large spacecraft

To insure the reliability of a 20 kHz, AC power system on spacecraft, it is essential to analyze its behavior under many adverse operating conditions. Some of these conditions include overloads, short circuits, switching surges, and harmonic distortions. Harmonic distortions can cause malfunctions in equipment that the power system is supplying, and during extreme distortions such as voltage resonance, it can cause equipment and insulation failures due to the extreme peak voltages. HARMFLO, a power flow computer program, which was capable of analyzing harmonic conditions on three phase, balanced, 60 Hz, AC power systems, was modified to analyze single phase, 20 kHz, AC power systems. Since almost all of the equipment used on spacecraft power systems is electrically different from equipment used on terrestrial power systems, it was also necessary to develop mathematical models for the equipment to be used on the spacecraft. The results are that (1) the harmonic power now has a model of a single phase, voltage controlled, full wave rectifier; and (2) HARMFLO was ported to the SUN workstation platform.

Kraft, L. Alan↗

Search for evidence of a clock related to the solar 154 day complex of periodicities

Evidence that has recently been compiled (Bai and Sturrock 1991) indicates that the enigmatic 154-day periodicity in solar activity may be viewed as part of a complex of periodicities that are approximate multiples of 25.8 days, suggesting that the Sun contains a 'clock' with frequency in the range 440 to 463 nano Hz. The clock may comprise either an oscillator or a rotator, each of which may be either real or virtual. We have reconsidered a previous spectrum analysis of the Zurich sunspot-number sequence by Knight, Schatten, and Sturrock (1979) which revealed a sharp, persistent and significant periodicity with a period of 12.072 days, corresponding to a frequency of about 958.8 nano Hz. This periodicity may be regarded as the (second) upper sideband of the second harmonic (2nu(sub R) + 2nu(sub E)) of a fundamental frequency of 447.7 nano Hz that is clearly within the search band. In this expression, nu(sub R) is the sidereal frequency of the hypothetical rotator and nu(sub E) is the frequency (31.69 nano Hz) of the Earth in its orbital motion around the Sun. In analyzing sunspot area data derived from the Greenwich data set, and on noting that any frequency is defined only to within the Nyquist frequency, we find clear evidence not only for the upper sideband of the second harmonic, but also for the second harmonic (2nu(sub R)) and the lower sideband of the second harmonic (2nu(sub R) - 2nu(sub E)). There is no strong peak at the fundamental frequency in the Greenwich data, but there is in the Zurich sunspot data. The effect of a linear oscillator is, to the lowest order in the amplitude, the same as the combined effect of two rotators of opposite polarities. A rotator that has arbitrary orientation with respect to the ecliptic may influence the outer layers of the Sun and thereby modulate the occurrence of solar activity such as sunspots. By analyzing a simple model, we find that such a rotator would influence surface activity in such a way that the spectrum of a 'signal' (such as the record of sunspots), as seen from the Earth, would contain components with frequencies that are certain integral combinations of nu(sub R) and nu(sub E). The amplitudes of the various components depend sensitively on theta, the angle between the axis of the rotator and the axis of the Earth's orbital motion. This simple model therefore offers a kinematical (but not dynamical) interpretation of the sunspot spectrum. The present analysis, while offering support of our conjectures that the Sun contains a clock that regulates the 154-day complex of periodicities, cannot distinguish between an osillator or a rotator (that might be a traveling wave), nor between a real rotator or a virtual rotator (that might be an apparent traveling wave due to the aliasing effect of an oscillator in a rotating system). Further analysis of sunspot and other data sets will be required to confirm the existence of such clock and (if it is real) to determine its physical nature.

Sturrock, P. A.↗

Development of software to improve AC power quality on large spacecraft

To insure the reliability of a 20 kHz, alternating current (AC) power system on spacecraft, it is essential to analyze its behavior under many adverse operating conditions. Some of these conditions include overloads, short circuits, switching surges, and harmonic distortions. Harmonic distortions can become a serious problem. It can cause malfunctions in equipment that the power system is supplying, and, during distortions such as voltage resonance, it can cause equipment and insulation failures due to the extreme peak voltages. To address the harmonic distortion issue, work was begun under the 1990 NASA-ASEE Summer Faculty Fellowship Program. Software, originally developed by EPRI, called HARMFLO, a power flow program capable of analyzing harmonic conditions on three phase, balanced, 60 Hz AC power systems, was modified to analyze single phase, 20 kHz, AC power systems. Since almost all of the equipment used on spacecraft power systems is electrically different from equipment used on terrestrial power systems, it was also necessary to develop mathematical models for the equipment to be used on the spacecraft. The modelling was also started under the same fellowship work period. Details of the modifications and models completed during the 1990 NASA-ASEE Summer Faculty Fellowship Program can be found in a project report. As a continuation of the work to develop a complete package necessary for the full analysis of spacecraft AC power system behavior, deployment work has continued through NASA Grant NAG3-1254. This report details the work covered by the above mentioned grant.

Kraft, L. Alan↗

Unsteady aerodynamic models for maneuvering aircraft

Forced oscillation tests over a large angle-of-attack range for an F-18 model are conducted in the NASA Langley 12-foot low-speed tunnel. The resulting dynamic longitudinal data are analyzed with an unsteady aerodynamic modeling method based on Fourier functional analysis and the indicial formulation. The method is extensively examined and improved to automate the calculation of model coefficients, and to evaluate more accurately the indicial integral. The results indicate that the general model equation obtained from harmonic test data in a range of reduced frequency is capable of accurately modeling the nonlinear responses with large hysteresis effect, except in the region where a delayed flow reattachment occurs at low angles of attack in down strokes. The indicial formulation is used to calculate the response to harmonic motion, harmonic ramp motion, constant-rate pitching motion and smaller-amplitude harmonic motion. The results show that more accurate results can be obtained when the motion starts from a low angle of attack where hysteresis effect is not important.

Hu, Chien-Chung↗

Dynamics and efficiency of type III solar radio emission

Existing calculations of nonlinear coupling coefficients for fundamental and harmonic emission via three-wave interactions are refined and used to calculate the conversion efficiency of Langmuir energy into electromagnetic waves when the Langmuir waves have the observed bursty form. Resulting field strengths for harmonic emission are found to be consistent with typical International Sun Earth Explorer 3 (ISSE 3) observations at 1 AU. Fundamental emission at 1 AU is found to proceed only when stimulated by the presence of a source of ion sound waves. However, it is argued that electrostatic decay of Langmuir waves can supply the necessary waves provided the driving electron beam is sufficiently fast. Under these conditions, the predicted fundamental field strengths can account for both the highest and typical fields observed; they also dominate the predicted harmonic fields, consistent with observations. This mechanism is also consistent with previous observations that fundamental emission generally occurs early in type III events, when the beam is fastest. For typical parameters it is shown that neither fundamental nor harmonic emission saturates its respective source instability, contrary to previous assumptions. However, saturation cannot be ruled out under particularly favorable conditions.

Robinson, P. A.↗

Effect of individual blade control on noise radiation

In a joint research program of NASA Ames Research Center, ZF Luftfahrttechnik, the German Aerospace Research Establishment (DLR), and EUROCOPTER Deutschland, a wind tunnel test was performed to evaluate the effects of Individual Blade Control (IBC) on rotor noise. This test was conducted in the 40x80 ft wind tunnel at NASA Ames Research Center, utilizing a full scale MBB-BO 105 four-bladed rotor system. Three microphones were installed for determination of the radiated noise, two of them on a moveable traverse below the advancing blade side and one in a fixed location below the retreating side. Acoustic results are presented for flight conditions with Blade-Vortex-Interaction (BVI) noise radiation. High noise level reductions were measured for single harmonic control inputs. In addition to the single harmonic inputs, multi-harmonic inputs were evaluated by superimposing 2/rev to 6/rev harmonics. For the first time the efficiency of sharp wavelets (60 deg and 90 deg width) on acoustic noise were measured. In order to achieve an adequate wavelet shape at the blade tip, corrections were made to account for the blade torsional behavior. In parallel with the acoustic measurements, vibratory loads were measured during the BVI flight condition to correlate the effects of IBC on noise and vibrations. It is shown how noise levels and vibrations are affected by specific IBC control inputs. In addition, correlations are made between noise levels and acoustic time histories with IBC phase and amplitude variations. For one IBC input mode with high noise reducing efficiency, a sweep of the moveable microphone traverse below the advancing side shows the effect on BVI noise directivity.

Swanson, S. M.↗

JPL-TMF multiwavelength aerosol lidar

The JPL-TMF Lidar Facility began operation in 1985 with the completion of a XeCl excimer based stratospheric ozone DIAL system. As an adjunct to this system a Nd:YAG based tropospheric ozone and aerosol system was assembled. The tropospheric ozone system was designed to utilize the fourth harmonic (266 nm) of the Nd:YAG to produce 289 nm, 294 nm or 299 nm by SRS in the isotopic hydrogen gases. The aerosol lidar was developed using the fundamental (1064 nm) and second harmonic of the Nd:YAG (532 nm). Following the eruption of Mount Pinatubo most of the effort was put into obtaining data on the layer structure of the volcanic aerosol as a function of altitude and time on a regular basis. During this period the tropospheric ozone DIAL was not employed on a regular schedule. The stratospheric measurements were of primary interest; however with the volcanic aerosol concentrated at the 16 - 26 km altitude the ozone concentration profile was perturbed. The aerosol interference in the ozone measurements caused the lidar community to seek techniques of measurement of the aerosol which could be used in making realistic corrections to the ozone measurements. It is generally accepted that a reasonable technique of measurement would include at least one channel of Raman scattering from a blue wavelength and a minimum of three other supporting wavelengths. With the primary transmitters available at TMF, a four wavelength system was considered for configuration. The four wavelength aerosol lidar is based on the Nd:YAG fundamental, the second and third harmonics of the transmitter. The receiver will separate these three wavelengths as well as the Raman scattering from atmospheric nitrogen of the third harmonic.

Haner, David A.↗

Parametric Identification of Nonlinear Dynamical Systems

In this project, we looked at the application of harmonic balancing as a tool for identifying parameters (HBID) in a nonlinear dynamical systems with chaotic responses. The main idea is to balance the harmonics of periodic orbits extracted from measurements of each coordinate during a chaotic response. The periodic orbits are taken to be approximate solutions to the differential equations that model the system, the form of the differential equations being known, but with unknown parameters to be identified. Below we summarize the main points addressed in this work. The details of the work are attached as drafts of papers, and a thesis, in the appendix. Our study involved the following three parts: (1) Application of the harmonic balance to a simulation case in which the differential equation model has known form for its nonlinear terms, in contrast to a differential equation model which has either power series or interpolating functions to represent the nonlinear terms. We chose a pendulum, which has sinusoidal nonlinearities; (2) Application of the harmonic balance to an experimental system with known nonlinear forms. We chose a double pendulum, for which chaotic response were easily generated. Thus we confronted a two-degree-of-freedom system, which brought forth challenging issues; (3) A study of alternative reconstruction methods. The reconstruction of the phase space is necessary for the extraction of periodic orbits from the chaotic responses, which is needed in this work. Also, characterization of a nonlinear system is done in the reconstructed phase space. Such characterizations are needed to compare models with experiments. Finally, some nonlinear prediction methods can be applied in the reconstructed phase space. We developed two reconstruction methods that may be considered if the common method (method of delays) is not applicable.

Feeny, Brian↗

BASS Code Development

The BASS computational aeroacoustic code solves the fully nonlinear Euler equations in the time domain in two-dimensions. The acoustic response of the stator is determined simultaneously for the first three harmonics of the convected vortical gust of the rotor. The spatial mode generation, propagation and decay characteristics are predicted by assuming the acoustic field away from the stator can be represented as a uniform flow with small harmonic perturbations superimposed. The computed field is then decomposed using a joint temporal-spatial transform to determine the wave amplitudes as a function of rotor harmonic and spatial mode order. This report details the following technical aspects of the computations and analysis. 1) the BASS computational technique; 2) the application of periodic time shifted boundary conditions; 3) the linear theory aspects unique to rotor-stator interactions; and 4) the joint spatial-temporal transform. The computational results presented herein are twofold. In each case, the acoustic response of the stator is determined simultaneously for the first three harmonics of the convected vortical gust of the rotor. The fan under consideration here like modern fans is cut-off at +, and propagating acoustic waves are only expected at 2BPF and 3BPF. In the first case, the computations showed excellent agreement with linear theory predictions. The frequency and spatial mode order of acoustic field was computed and found consistent with linear theory. Further, the propagation of the generated modes was also correctly predicted. The upstream going waves propagated from the domain without reflection from the in ow boundary. However, reflections from the out ow boundary were noticed. The amplitude of the reflected wave was approximately 5% of the incident wave. The second set of computations were used to determine the influence of steady loading on the generated noise. Toward this end, the acoustic response was determined with three steady loading conditions: design, low-loading, high-loading. The overall trend showed significant (approximately 10 dB) increases in the generated noise for the highly loaded stator.

Sawyer, Scott↗

Analysis of variability in the burst oscillations of the accreting millisecond pulsar XTE J1814-338

The accreting millisecond pulsar XTE J1814-338 exhibits oscillations at the known spin frequency during Type I X-ray bursts. The properties of the burst oscillations reflect the nature of the thermal asymmetry on the stellar surface. We present an analysis of the variability of the burst oscillations of this source, focusing on three characteristics: fractional amplitude, harmonic content and frequency. Fractional amplitude and harmonic content constrain the size, shape and position of the emitting region, whilst variations in frequency indicate motion of the emitting region on the neutron star surface. We examine both long-term variability over the course of the outburst, and short-term variability during the bursts. For most of the bursts, fractional amplitude is consistent with that of the accretion pulsations, implying a low degree of fuel spread. There is however a population of bursts whose fractional amplitudes are substantially lower, implying a higher degree of fuel spread, possibly forced by the explosive burning front of a precursor burst. For the first harmonic, substantial differences between the burst and accretion pulsations suggest that hotspot geometry is not the only mechanism giving rise to harmonic content in the latter. Fractional amplitude variability during the bursts is low; we can only rule out the hypothesis that the fractional amplitude remains constant at the l(sigma) level for bursts that do not exhibit photospheric radius expansion (PRE). There are no significant variations in frequency in any of the bursts except for the one burst that exhibits PRE. This burst exhibits a highly significant but small (= 0.1Hz) drop in frequency in the burst rise. The timescale of the frequency shift is slower than simple burning layer expansion models predict, suggesting that other mechanisms may be at work.

Watts, Anna L.↗

Ultrasonic method and apparatus for determining crack opening load

An ultrasonic apparatus determines crack opening load by placing a transmit transducer on one side of the crack and a receive transducer on the opposite side of the crack. An acoustic signal passing through a region of the crack is mechanically rectified to produce a second harmonic of an input signal. A harmonic output signal of the receive transducer is converted into an electrical signal and the peak harmonic amplitude is determined while increasing a tension load on the specimen. The peak harmonic amplitude indicates crack opening load.

Yost, William T.↗

Measuring Parameters of Massive Black Hole Binaries with Partially Aligned Spins

The future space-based gravitational wave detector LISA will be able to measure parameters of coalescing massive black hole binaries, often to extremely high accuracy. Previous work has demonstrated that the black hole spins can have a strong impact on the accuracy of parameter measurement. Relativistic spin-induced precession modulates the waveform in a manner which can break degeneracies between parameters, in principle significantly improving how well they are measured. Recent studies have indicated, however, that spin precession may be weak for an important subset of astrophysical binary black holes: those in which the spins are aligned due to interactions with gas. In this paper, we examine how well a binary's parameters can be measured when its spins are partially aligned and compare results using waveforms that include higher post-Newtonian harmonics to those that are truncated at leading quadrupole order. We find that the weakened precession can substantially degrade parameter estimation, particularly for the "extrinsic" parameters sky position and distance. Absent higher harmonics, LISA typically localizes the sky position of a nearly aligned binary about an order of magnitude less accurately than one for which the spin orientations are random. Our knowledge of a source's sky position will thus be worst for the gas-rich systems which are most likely to produce electromagnetic counterparts. Fortunately, higher harmonics of the waveform can make up for this degradation. By including harmonics beyond the quadrupole in our waveform model, we find that the accuracy with which most of the binary's parameters are measured can be substantially improved. In some cases, the improvement is such that they are measured almost as well as when the binary spins are randomly aligned.

Lang, Ryan N.↗

Comment on "An Analysis of VLF Electric Field Spectra Measured in Titan's Atmosphere by The Huygens Probe" By J. A. Morente et al.

Morente et al. have recently revisited the VLF electric field measurements made with the Permittivity, Wave and Altimetry (PWA) instrument during the descent of the Huygens Probe through the atmosphere of Titan. They assert that they have identified several harmonics of the transverse resonance mode of the surface?]ionosphere cavity, which would prove the existence of an electrical activity in the atmosphere of the largest satellite of Saturn. We refute this finding on the basis that it results from an artifact due to an improper analysis of the data set. [2] The investigators of the Permittivity, Wave and Altimetry (PWA) experiment on the Huygens Probe have reported the extremely low frequency (ELF) and very low frequency (VLF) electric signals recorded during the descent through the atmosphere of Titan. The PWA data are archived in the Planetary Science Archive (PSA) of ESA, and an extensive description of the instrument is at the disposal of the scientific community. Morente and his coworkers have revisited this data set and reported the results of their investigations in two papers. In a first paper, they claim that they have detected in the ELF range (0.100 Hz) several harmonics of a global resonance allegedly generated by lightning activity in the spherical cavity guide formed by the surface of Titan and the inner boundary of the ionosphere, a phenomenon similar to the Schumann resonance observed at EartH In the second paper dedicated to the VLF electric signal recorded by PWA, in the range 0.10 kHz, they argue that they can also bring out the transverse resonance and its harmonics, a more local phenomenon that develops around the excitation source and whose frequency is controlled by the separation between Titan?fs surface and the inner ionospheric boundary. [3] The PWA investigators have analyzed the narrowband ELF signal at about 36 Hz effectively observed during the entire descent. They have not endorsed, however, the alternative approach of Morente et al. that discloses additional ELF narrow-band signals and numerous related harmonics. Hamelin et al. and Beghin et al. have questioned the work of Morente and his coworkers and demonstrated unambiguously that their findings are mere artifacts entirely due to a faulty procedure. Morente et al. refuted this critical analysis of their ELF paper in a rebuttal. The present comment draws a parallelism between the ELF and VLF papers and demonstrates that the VLF signal carries no evidence whatever of any transverse resonance. The analyses of the ELF and VLF signals by Morente and his coworkers are flawed, and their conclusions are shown here to be invalid. A more comprehensive and thorough assessment of the numerical approaches proposed by Morente et al. is given by Berthelin et al..

Grard, Rejean↗