SEARCH · Engineering Papers

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Development and use of computational techniques in Army Aviation research and development programs for crash resistant helicopter technology

During the 1960's over 30 full-scale aircraft crash tests were conducted by the Flight Safety Foundation under contract to the Aviation Applied Technology Directorate (AATD) of the U.S. Army Aviation Systems Command (AVSCOM). The purpose of these tests were to conduct crash injury investigations that would provide a basis for the formulation of sound crash resistance design criteria for light fixed-wing and rotary wing aircraft. This resulted in the Crash Survival Design Criteria Designer's Guide which was first published in 1967 and has been revised numerous times, the last being in 1989. Full-scale aircraft crash testing is an expensive way to investigate structural deformations of occupied spaces and to determine the decelerative loadings experienced by occupants in a crash. This gave initial impetus to the U.S. Army to develop analytical methods to predict the dynamic response of aircraft structures in a crash. It was believed that such analytical tools could be very useful in the preliminary design stage of a new helicopter system which is required to demonstrate a level of crash resistance and had to be more cost effective than full-scale crash tests or numerous component design support tests. From an economic point of view, it is more efficient to optimize for the incorporation of crash resistance features early in the design stage. However, during preliminary design it is doubtful if sufficient design details, which influence the exact plastic deformation shape of structural elements, will be available. The availability of simple procedures to predict energy absorption and load-deformation characteristics will allow the designer to initiate valuable cost, weight, and geometry tradeoff studies. The development of these procedures will require some testing of typical specimens. This testing should, as a minimum, verify the validity of proposed procedures for providing pertinent nonlinear load-deformation data. It was hoped that through the use of these analytical models, the designer could optimize aircraft design for crash resistance from both a weight and cost increment standpoint, thus enhancing the acceptance of the design criteria for crash resistance.

Burrows, Leroy T.↗

DOE OSTI2023

PRINTED, PLANAR MICROWAVE CONNECTOR WITH MULTIPLE SIGNAL LINES

Microwave connectors with a planar geometry have been demonstrated using additive manufacturing techniques. This planar form factor is expected to enable connectors to be integrated directly with other components onto a printed circuit board. The connectors were developed with multiple signal lines that will increase the density of signal connections to PCBs, eliminating the physical constraints of single-signal COTS microwave connectors. This work developed electromagnetic models (using Ansys HFSS) of these planar connectors to predict performance and optimize connector design. Materials and printing processes were developed to fabricate the connectors based on high-temperature PEEK thermoplastics. The multiple signal connectors were designed to operate over the 1-6GHz band and are built upon the single signal printed planar geometry connector introduced in a previous paper [1].

Additive Manufacturing↗

DOE OSTI2025

Design Overview of a High-Pressure Helium Flow Visualization Apparatus for Blanket Cooling Studies

Cooling of the fusion blanket first wall remains a significant challenge given the adverse conditions of heat and particle flux encountered near the plasma. Helium emerges as an attractive cooling candidate because of its chemical and neutronic inertness and separability from hydrogenic species (e.g. tritium). Because of the low thermal mass of helium, optimization of these coolant channels is warranted to provide high heat transfer performance at low pumping costs. Increasingly, computational fluid dynamics (CFD) simulations are employed to model and optimize these flow channels, and accompanying experimental data are needed to validate the predictions of these models. To provide the aforementioned experimental data, a high-pressure helium flow visualization upgrade has been designed for the Helium Flow Loop Experiment facility. This apparatus was built to American Society of Mechanical Engineers boiler and pressure vessel standards to withstand operating pressure of 4 MPa and mated to high-pressure glass windows. Seedless flow visualization is performed via high-speed background oriented schlieren (BOS), with image correlation used for time-resolved two-dimensional velocimetry at frequencies in excess of 60 kHz. Rectangular flow channel test articles are additively manufactured via laser powder bed fusion and installed into this visualization apparatus, with one-sided heating supplied by resistive heaters. In conclusion, the chosen test geometries were informed by prior CFD simulations, and the helium flow structures observed via BOS (detachment, recirculation, etc.) will be used for the validation of these accompanying models, in support of the design and optimization of blanket cooling channel configurations.

Helium flow↗

DOE OSTI2024

Optimizing Aluminum Bonding: Exploring Surface Roughness and Contact Angle Effects through Plasma and Acid Etching Contrasts

The use of adhesives to replace traditional techniques like welding and riveting has been on the rise in various industries as increasingly complex geometries and situations for bonding is required. It’s well known in the scientific community that an adhesive bond is only as efficient as the surface preparation used beforehand. Plasma treatments have been shown to gently clean the surface by only removing the top-most layer from the adherend and “charging” the surface instead of berating it. Whereas chemical treatments “etch” the surface in hopes of increasing surface area by increasing surface roughness. This method can be difficult to control quantitatively and can generate waste leading to serious environmental concerns. This study aims to address the encountered differences between plasma treatments and acid etching on aluminum substrates for adhesive bonding. Treating the surface of adherends plays a crucial role in promoting a good bond between adhesive and adherend. In this study, the effects of plasma and acid treatments are categorized using surface roughness measurements as well as contact angle which have been shown to correlate to mechanical strength. When evaluating different surface treatments, it is notable to mention that not only surface roughness and contact angle play a role in determining which method is most effective but also the consequences of the treatment itself. It was found that although chemical etching was the most effective in increasing roughness and decreasing contact angle, it generates a large amount of waste and is not sustainable compared to plasma work which uses a renewable process. The results from this work provide a deeper understanding of the relationship between surface treatments and surface roughness/contact angle and how this relates to a stronger adhesive bond.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Optimizing Aluminum Bonding: Exploring Surface Roughness and Contact Angle Effects through Plasma and Acid Etching Contrasts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1976

Shape optimization of disc-type flywheels

Techniques were developed for presenting an analytical and graphical means for selecting an optimum flywheel system design, based on system requirements, geometric constraints, and weight limitations. The techniques for creating an analytical solution are formulated from energy and structural principals. The resulting flywheel design relates stress and strain pattern distribution, operating speeds, geometry, and specific energy levels. The design techniques incorporate the lowest stressed flywheel for any particular application and achieve the highest specific energy per unit flywheel weight possible. Stress and strain contour mapping and sectional profile plotting reflect the results of the structural behavior manifested under rotating conditions. This approach toward flywheel design is applicable to any metal flywheel, and permits the selection of the flywheel design to be based solely on the criteria of the system requirements that must be met, those that must be optimized, and those system parameters that may be permitted to vary.

Nizza, R. S.↗

DOE OSTI2025

A Bottom-Up Cost Estimation Tool for Nuclear Microreactors

The rising interest in nuclear microreactors has highlighted the need for comprehensive technoeconomic assessments. However, the scarcity of publicly available designs and cost data has posed significant challenges. To address this issue, the Microreactor Optimization Using Simulation and Economics (MOUSE) tool is developed. MOUSE is a tool that integrates nuclear microreactor design with reactor economics. The design calculations encompass core simulations using the OpenMC Monte Carlo Particle Transport Code [romano2015], along with simplified balance of plant calculations. On the economic side, MOUSE provides detailed bottom-up cost estimates, calculating both the total capital cost and the levelized cost of energy for first-of-a-kind and nth-of-a-kind microreactors. The cost estimation correlations are developed using data from the MARVEL project and additional literature sources. MOUSE has released as an open-source tool on GitHub (MOUSE Tool). By combining design calculations with cost equations, MOUSE enables users to evaluate the impact of various technological consideration, advanced moderators, design changes, material/fuel changes, and geometry modifications—as well as economic parameters like interest rates and construction duration. This comprehensive framework can guide stakeholders towards technological solutions that enhance microreactor competitiveness. Additionally, powered by the WATTS toolkit [romano2022], MOUSE supports optimization studies, parametric analyses, and uncertainty calculations/propagation. Currently, preconceptual designs of three microreactor types are included in MOUSE: a liquid metal thermal microreactor (LTMR), gas cooled TRISO-fueled microreactor (GCMR) and heat-pipe TRISO fueled microreactor (HPMR). To showcase its ability, MOUSE was used to conduct detailed bottom-up cost estimates for the first of a kind (FOAK) and Nth of a kind (NOAK) of the following microreactors • A 20MWt LTMR that is built on the ongoing MARVEL demonstration at Idaho National Laboratory (INL) • A 15 MWt GCMR that was designed to be more representative of the typical commercial microreactor • A 7 MWt HPMR that was built on previous work (Choi 2024) The The reader should note that these three designs and corresponding cost estimates are examples to demonstrate the MOUSE capability. The designs are pre-conceptual, the reactor designs were not optimized, and the cost estimates were developed with incomplete information. Additionally, stakeholders might be interested in a variety of designs that may differ from the examples provided in this report. The MOUSE tool can also be used to study how design choices affect economics. To demonstrate its capability, MOUSE was used conduct parametric studies such as examining the economic impact of the reflector's material and thickness, the moderator's booster material and dimensions, fuel composition and enrichment, core size, and power level. Several insights were gained from these parametric studies.

Hanna, Botros↗

NASA NTRS2002

GTX Reference Vehicle Structural Verification Methods and Weight Summary

The design of a single-stage-to-orbit air breathing propulsion system requires the simultaneous development of a reference launch vehicle in order to achieve the optimal mission performance. Accordingly, for the GTX study a 300-lb payload reference vehicle was preliminarily sized to a gross liftoff weight (GLOW) of 238,000 lb. A finite element model of the integrated vehicle/propulsion system was subjected to the trajectory environment and subsequently optimized for structural efficiency. This study involved the development of aerodynamic loads mapped to finite element models of the integrated system in order to assess vehicle margins of safety. Commercially available analysis codes were used in the process along with some internally developed spreadsheets and FORTRAN codes specific to the GTX geometry for mapping of thermal and pressure loads. A mass fraction of 0.20 for the integrated system dry weight has been the driver for a vehicle design consisting of state-of-the-art composite materials in order to meet the rigid weight requirements. This paper summarizes the methodology used for preliminary analyses and presents the current status of the weight optimization for the structural components of the integrated system.

Hunter, J. E.↗

DOE OSTI2023

Study of Cathode and Cavity Geometries in Electropolishing (EP): Electric Field Simulation

Niobium (Nb) superconducting radio frequency (SRF) cavities require electropolishing surface treatment to reach high acceleration gradient. EP performed in the plateau region of an I-V curve [1] leads to a smooth finish of the cavity surface including the equator surface. The equator surface is vital because a rough equator surface leads to premature quench and limit the cavity performance. Previous experimental work was performed to optimize EP parameters for low-beta (LB) 650 MHz Nb cavity [1]. It was found that different cathode surface areas vary the plateau onset voltage. A lower onset voltage was achieved for HB650 cavity with an enlarged cathode surface area. The aim of the study is to perform electrostatic and electrochemical simulation to understand the impact of both cavity geometry and cathodes. This report covers an initial result on electric field simulation performed with HB and LB 650 MHz cavities.

Loer, Bereket↗

DOE OSTI2025

Evaluating the Origins of Aerobic Oxidation Catalysis with TAM-3, a MOF with Accessible Co(II) Sites and Large Pores

Metal-organic frameworks (MOFs) are attractive platforms that merge concepts of homogeneous and heterogeneous catalysis. Catalyst design and optimization are enabled by an array of synthetic methods that offer independent control over the local chemical structure of lattice-embedded metal ions (i.e., ligand identity and geometry) and the long-range materials properties (i.e., porosity). Establishing the origin of catalytic activity in MOF-promoted reactions remains a significant challenge: The relative rates of catalyst turnover and substrate diffusion dictate the extent to which interstitial sites are accessible and operational in catalysis. To minimize the contributions of surface sites in catalysis, materials with large pore dimensions are often sought, however, the impact of pore expansion on the origins of catalytic activity is similarly challenging to establish. Here, we describe TAM-3, a Co(II) based MOF with accessible metal sites supported by a facially coordinating tris-tetrazole ligand set. TAM-3 features large channel-like pores (17 × 23 Å) and promotes aerobic C−H oxidation and olefin epoxidation. Using a set of simple kinetics experiments, based on the analysis of kinetic isotope effects and olefin oxidation diastereoselectivities, we demonstrate that despite the large pores, interstitial metal ions do not significantly contribute to the observed substrate oxidation. This study highlights the importance of conducting kinetic experiments to assess the origin of apparent catalytic activity with MOFs and the challenge of harnessing reactive oxidants with microporous catalyst materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Interpretation of borehole strain measurements using surrogate modeling-based optimization

Interpreting strain data measured during well testing requires inverting poroelastic forward models set up to represent an aquifer or reservoir. One approach is to use stochastic methods to conduct the inversion. Subsurface parameters such as elastic modulus, permeability, and geometry of heterogeneities are estimated by searching the parameter space. This is feasible, but cumbersome, requiring more than a week of computation using many hundreds of computer nodes in one of our earlier analyses. This motivated us to consider alternative methods, including an artificial neural network (ANN) as a surrogate model.

Roudini, Soheil↗

DOE OSTI2025

Project Title: Demonstration High Temperature Superconducting NonPlanar Stellarator Magnet with Advanced Manufactured Assemblies

This is the final report for the project “Demonstration High Temperature Superconducting Non- Planar Stellarator Magnet with Advanced Manufactured Assemblies”, funded by DOE, and performed by Type One Energy from September, 2020, to March 2024 involving the Fusion Technology Institute at the University of Wisconsin–Madison, the Plasma Science and Fusion Center (PSFC) at the Massachusetts Institute of Technology (MIT) and Commonwealth Fusion Systems (CFS) to design and fabricate the first non-planar HTS (REBCO) coil for a high-field stellarator based on the SPARC tokamak’s VIPER cable concept. Stellarators at high fields make high-temperature superconducting magnets necessary for a compact fusion device. But the asymmetric and non-planar nature of its components, especially the magnets make it difficult for scalable producibility. To address these challenges, two promising technologies have emerged: advanced manufacturing (AM) for the supporting plates for forming the magnets, and high-temperature superconducting (HTS) cables inside the plates. AM has advanced enough to produce stellarator components with the necessary geometric complexity, size, and the precision, leading to potentially significant reductions in production time, cost, and waste. The cost of HTS tape has decreased dramatically, and progress in HTS planar magnet development has reached a point where it can be proposed for application to complex 3D non-planar magnets. The main objective of this project is to develop, demonstrate and pre-commercialize a novel, non-planar HTS coil shape that remains superconducting to achieve production scalable reductions in time and cost and performance. The proposed technology is based on the novel concept of a precision sub-scale HTS nonplanar coil assembly. This project focuses on the design, fabrication, material optimization of cable design, and validation and demonstration of the high current carrying capability of superconducting magnets and their support in a complex 3D shape needed for application to stellarator magnetic plasma confinement. The specific objectives of this research program include: (1) The successful application of metal AM to build a precision sub-scale HTS nonplanar coil, (2) An HTS cable and cross-section design that can conform to the required nonplanar coil shape (bend radii as tight as 10-cm) and remains superconducting at an engineering current density of 1.35 kA/cm 2 at 77 K and 1 tesla at the conductor (5 kA in the cable). To achieve the above challenging goals, we have formed a multidisciplinary research team consisting of members from Type One Energy and UW-Madison, MIT PSFC and CFS with complementary skills and strong facilities. The team worked collaboratively on fundamental and applied research on the following three major technical areas: (1) Design, fabrication, and optimization of non-planar HTS Cable The ultimate goal of the project is to determine if commercial REBCO tapes and additive manufacturing can be used to fabricate high field (≥ 10T) non-planar coils with tight bending radii (≃ 100mm) and with a degradation of the critical current (Ic) smaller than 20% with respect to the expected performance. We started with shorter length cable to evaluate the scalability of the production process and eventually reached multiple turns for higher magnetic fields. Our findings suggest that a stellarator coil system of a relevant size, characterized by its asymmetric and non-planar components, can be fabricated using a formed cable in plate method. This system can be simulated using a large-scale modeling approach. The use of hybrid modeling 3 techniques will be pivotal in reducing the complexity of the model and in assessing expected performance in designs. (2) Modeling and simulation of the non-planar HTS Cable Multiphysics simulations are performed using the commercial software and are carried out in self-field conditions, involving 2D and 3D models and twisted around one slot of twist-pitched VIPER cable. Multiphysics simulations are mainly focused on the coil for the critical current evaluation, the magnetic field map, self-Lorentz forces and mechanical, and magnetothermal behavior and the quench dynamics. The detailed model and prediction of the superconducting performance of a stellarator-relevant demonstration cable from numerical simulations supports the results from the actual testing backing the results. A detailed description and results are provided in the later sections. (3) Design, fabrication, and optimization of support for the non-planar HTS Cable The team developed an additive manufactured (AM) coil positioning plate that formed into the required non-planar geometry (with bend radii as tight as 10-cm) and to acceptable tolerances required for a stellarator magnet: (+0.25-mm from ideal on dimensions of coil positioning plates and up to +1-mm from ideal for position of wound coil). The plate materials is also included in this selection process from fabrication and 3D printing perspective and commensurate with eventual application to a fusion reactor. From the cost effectiveness point of view, the HTS coil and plate has the potential to cost less than that made in conventional methods with less waste (<75% waste) reducing time (<50%) and cost (<50%), especially as the AM field matures. The application of advanced manufacturing in the construction of the support plates will also lead to cost reduction, as the cables can be easily replaced, thereby making the assembly modular. With such high primary cost and time savings, high current densities and magnetic field, the funded R&D work has validated the designs, proven the feasibility, and characterized the performance of the HTS coil and plate assembly, paving the way for a relevant-size stellarator coil system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Core Physics Characteristics of Extended Enrichment and High Burnup Boiling Water Reactor Fuel

This paper presents the highlights of boiling water reactor (BWR) core physics studies performed at Oak Ridge National Laboratory as part of a series of studies conducted to compare low-enriched uranium (LEU) with LEU+ fuel. The studies analyzed isotopic fuel content, lattice parameters (Phase 1), and core physics (Phase 2) to identify challenges in operation, storage, and transportation for BWRs and pressurized water reactors (PWRs). Because of a lack of publicly available lattice and core designs for modern BWR fuel assemblies and reactor cores, several optimized lattice designs were generated, and different core loading strategies were investigated. Twelve optimized lattice designs with 235 U enrichments ranging from 1.6% to 9% and gadolinia loadings ranging from 3 to 8 wt% were used to model axial enrichment and geometry variations in fuel assemblies for core designs. Each core shares a common set of approximations in design and analysis to allow for consistent comparisons between LEU and LEU+ fuel. The objective is to highlight anticipated changes in core behavior with respect to the reference LEU core. The results of this study show that the differences in LEU and LEU+ core reactor physics characteristics are less significant than the differences in lattice physics characteristics reported in the Phase 1 studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1981

High frequency plasma generators for ion thruster applications

Two concepts for high frequency discharge ion thrusters are described. Both sources are designed for use with 30 cm grid sets and argon propellant and utilize multi-cusp permanent magnet geometries for plasma confinement. The RF induction source is a conventional design representing a synthesis of the RIT and multi-cusp concepts. The preliminary data (without system optimization) indicate a discharge efficiency comparable to that obtained in 30 cm hollow cathode multi-cusp argon thrusters. The electron cyclotron heating source is electrodeless and exhibits plasma characteristics which should lead to greatly reduced discharge chamber and screen sputter rates with the optimization of the magnetic fields, microwave frequency, and feed configuration.

Divergilio, W. F.↗

NASA NTRS1986

Optimally robust redundancy relations for failure detection in uncertain systems

All failure detection methods are based, either explicitly or implicitly, on the use of redundancy, i.e. on (possibly dynamic) relations among the measured variables. The robustness of the failure detection process consequently depends to a great degree on the reliability of the redundancy relations, which in turn is affected by the inevitable presence of model uncertainties. In this paper the problem of determining redundancy relations that are optimally robust is addressed in a sense that includes several major issues of importance in practical failure detection and that provides a significant amount of intuition concerning the geometry of robust failure detection. A procedure is given involving the construction of a single matrix and its singular value decomposition for the determination of a complete sequence of redundancy relations, ordered in terms of their level of robustness. This procedure also provides the basis for comparing levels of robustness in redundancy provided by different sets of sensors.

Lou, X.-C.↗

NASA NTRS1993

Optimal design of a composite structure

This paper presents a design methodology for a laminated composite stiffened panel, subjected to multiple in-plane loads and bending moments. Design variables include the skin and stiffener ply orientation angles and stiffener geometry variables. Optimum designs are sought which minimize structural weight and satisfy mechanical performance requirements. Two types of mechanical performance requirements are placed on the panel, maximum strain and minimum strength. Minimum weight designs are presented which document that the choice of mechanical performance requirements cause changes in the optimum design. The effects of lay-up constraints which limit the ply angles to user specified values, such as symmetric or quasi-isotropic laminates, are also investigated.

Graesser, D. L.↗

NASA NTRS2001

In-Flight Edge Response Measurements for High Spatial Resolution Remote Sensing Systems

In-flight measurement of spatial resolution were conducted as part of the ASA Scientific Data Purchase (SDP) Validation and Verification (V&V) process. Characterization included remote sensing systems with ground sample distance (GSD) of 1 meter or less, such as the panchromatic imager on-board the ICONOS satellite and the airborne ADAR System 5500 multispectral instrument. Final image products were used to evaluate the effect of both the image acquisition system (e.g., optics, electronics, motion, jitter, atmosphere) and image post-processing (e.g., resampling, modulation trasfer function (MTF) compensator). Spatial resolution was characterized by full width at half maximum (FWHM) of an edge response-derived line spread function. This was found to be a more robust measure of spatial resolution than the value of NTF at Nyquist frequency The edge responses were analysed using the tilted-edge technique that ovecomes the spatial sampling limitations of the digital imaging systems. As an enhancement to existing algorithms, the slope of the edge response and the orientation of the edge target were determined by a single computational process. Adjacent black and white square panels, either painted on a flat surface or deployed as traps, formed the ground-based edge targets used in the tests. Orientation of the deployable tarps was optimized beforehand, based on simulations of the imaging system. Numerous edge target images were analyzed for each of the tested sensors. The effect of such factors as acquisition geometry, temporal variability, MTF compensation, and GSD on spatial resolution were investigated.

Blonski, Slawomir↗

NASA NTRS2005

A Viable Scheme for Elemental Extraction and Purification Using In-Situ Planetary Resources

NASA's new strategic direction includes establishing a self-sufficient, affordable and safe human and robotic presence outside the low earth orbit. Some of the items required for a self-sufficient extra-terrestrial habitat will include materials for power generation (e.g. Si for solar cells) and habitat construction (e.g. Al, Fe, and Ti). In this paper we will present a viable elemental extraction and refining process from in-situ regolith which would be optimally continuous, robotically automated, and require a minimum amount of astronaut supervision and containment facilities, The approach is based on using a concentrated heat source and translating sample geometry to enable simultaneous oxide reduction and elemental refining. Preliminary results will be presented to demonstrate that the proposed zone refining process is capable of segregating or refining important elements such as Si (for solar cell fabrication) and Fe (for habitat construction). A conceptual scheme will be presented whereby such a process could be supported by use of solar energy and a precursor robotic mission on the surface of the moon.

Sen, S.↗