Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fusion experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Quench Propagation On Rare-Earth Barium Copper Oxide (REBCO) Tape

Rare-earth barium copper oxide (REBCO) high-temperature superconductors can carry high currents with zero electrical resistance, enabling applications in high-field magnets, energy systems, and fusion devices. However, localized losses of superconductivity, known as quenches, pose a severe risk due to REBCO’s mechanical brittleness and slow quench propagation, complicating early detection. This work investigates quench propagation and thermal response through controlled experiments. A segmented REBCO tape soldered onto a printed circuit board (PCB) with multiple voltage taps and temperature sensors was submerged in liquid nitrogen at 77 K. In the first test, current ramping produced a quench near 360 A, consistent with theoretical current limits, but resulted in local burnout. In the second test, a heater-induced quench at 300 A propagated bidirectionally with velocities ranging from 164–226 mm/s. These results provide critical parameters for improving REBCO quench detection and protection system design while accounting for REBCO’s limited bendability.

Ju, Han [Northern Illinois U.]↗
NASA NTRS2012

Studies of Thermophysical Properties of Metals and Semiconductors by Containerless Processing Under Microgravity

Electromagnetic levitation under microgravity provides unique opportunities for the investigation of liquid metals, alloys and semiconductors, both above and below their melting temperatures, with minimized disturbances of the sample under investigation. The opportunity to perform such experiments will soon be available on the ISS with the EML payload which is currently being integrated. With its high-performance diagnostics systems EML allows to measure various physical properties such as heat capacity, enthalpy of fusion, viscosity, surface tension, thermal expansion coefficient, and electrical conductivity. In studies of nucleation and solidification phenomena the nucleation kinetics, phase selection, and solidification velocity can be determined. Advanced measurement capabilities currently being studied include the measurement and control of the residual oxygen content of the process atmosphere and a complementary inductive technique to measure thermophysical properties.

Seidel, A.↗
DOE OSTI2021

Thermal stability of additively manufactured austenitic 304L ODS alloy

Thermal stability and high-temperature mechanical properties of a 304L austenitic oxide dispersion strengthened (ODS) alloy manufactured via laser powder bed fusion (LPBF) are examined in this work. Additively manufactured 304L ODS alloy samples were aged at temperatures of 1000, 1100, and 1200 °C for 100 h in an argon atmosphere. Microstructure characterization of LPBF 304L ODS alloy before and after the thermal stability experiments revealed that despite the annihilation of dislocations, induced cellular substructure by the LPBF process was partially retained in the ODS alloy even after aging at 1200 °C. The size of Y-Si-O nanoparticles after aging at 1200 °C increased from 25 to 50 nm. EBSD analysis revealed that nanoparticles retained the microstructure of LPBF 304L ODS and hindered recrystallization and further grain growth. At 600 °C and 800 °C, the yield stress of the 290 and 145 MPa were measured, respectively, which are substantially higher than 113 MPa, and 68 MPa for 304L at the same temperatures. Furthermore, the creep properties of LPBF 304L ODS alloy were evaluated at a temperature of 700 °C under three applied stresses of 70, 85, and 100 MPa yielding a stress exponent (n) of ~7.7; the minimum creep rate at 100 MPa was found to be about two orders of magnitude lower than found in the literature for wrought 304L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantitative Non-Destructive Evaluation of Fatigue Damage Based on Multi-Sensor Fusion

Based on sensor fusion and machine learning, this project developed a novel non-destructive evaluation (NDE) methodology, which consists of a remaining useful life (RUL) prediction framework and regression models for predicting residual stress and full width at half maximum (FWHM). A series of fatigue testing experiments were conducted using 5052-H32 aluminum alloy specimens. All specimens were measured using linear ultrasonic (LU) and nonlinear ultrasonic (NLU) testing methods non-destructively. Machine learning models were developed to use LU and NLU measurements to predict loading condition, fatigue level, residual stress, and FWHM. It was demonstrated that the developed methodology could distinguish new and fatigue specimens with an accuracy of 97.53%. Also, the prediction errors for residual stress and FWHM were as low as 4.73% and 1.62%, respectively. An interactive database was created to publicly share the data generated from the project. It is envisioned that the developed NDE technology will equip manufacturers with a responsive screening system for incoming used metallic components, and potentially lead to a significant increase in using used metallic components for remanufacturing.

42 ENGINEERING↗
DOE OSTI2024

NSTX-U National Research Program: White Paper in Response to Call from FESAC Sub-Committee

Both scientific and technical innovation is needed for the realization of an attractive engineering solution for a timely and cost-effective Pilot Plant, the design and construction of which is the overarching recommendation of the FESAC Long Range Plan, and the 2021 NASEM Pilot Plant reports, which underpin the Bold Decadal Vision. The two most significant plasma physics gaps to close for a Compact Pilot Plant (CPP) are core confinement improvement and heat flux mitigation, neither of which have been closed in an integrated fashion for any planned fusion power production device. High core confinement and stability are essential for producing majority self-driven plasmas in CPPs with reduced size and auxiliary heating power requirements, with an improvement in confinement being the major driver for cost reduction of a CPP. The National Spherical Tokamak Experiment - Upgrade (NSTX-U) is a unique low aspect ratio research facility that will address the fundamental challenge of developing the science and technology basis for a CPP design that integrates high core and edge confinement with the ability to mitigate very high incident heat fluxes. NSTX-U capabilities will enable the high performance, already achieved on NSTX, to extend into physics regimes much closer to those anticipated in Spherical Tokamak (ST)-based CPPs. These confinement and stability properties will be assessed by a full complement of diagnostics and analysis tools, which will also aid in the development of the underlying theory and predictive models needed for further optimization. Both conventional and transformative heat flux mitigation methods, such as liquid lithium plasma-facing components, will be developed and tested in-situ in NSTX-U at incident heat fluxes of ~100 MW/m 2 , and will inform plans and reduce risk for a subsequent major upgrade to the device to fully heated, high-Z wall and full liquid lithium divertor capability, a technology that potentially could then be implemented on any magnetic confinement device at any aspect ratio. NSTX-U research is fully complementary to programs performed on other STs, nationally and internationally. Furthermore, NSTX-U research has a direct connection to the private sector by informing design choices for future power production facilities being developed by these companies. The NSTX-U program will operate as a national User Facility, with collaborating researchers, engineers, and graduate students from 19 outside institutions, and open to participation and experiments led by researchers from both public and private entities. The research program will advance workforce development through training of young scientists, engineers, and technicians, and it will also serve for further diagnostic innovation, especially for high heat flux and high-Z wall environments, and implementation of advanced artificial intelligence (AI) for plasma and heat flux control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A database and meta-analysis on the performance of exploding pusher implosions conducted at OMEGA

A database of 222 exploding pusher implosions conducted at the OMEGA Laser Facility is presented. The dataset consists of glass-shell capsules filled with varying pressures of D 2 , T 2 , and 3 He, which were imploded using square laser pulses with intensities ranging from 1 to 1 × 10 15 W/cm 2 . The database includes measurements of bang times, ion temperatures, and yields from the DD, D 3 He, and DT fusion reactions. A semi-analytic exploding pusher model is introduced, which effectively captures the observed trends in the data. This model predicts that the measurements scale according to a power-law relation based on the initial capsule and laser conditions. A generalized power-law scaling relation is directly fit to each dataset, providing a useful interpolation of the entire database. Overall, the database provides a valuable resource to estimating bang times, temperatures, and yields for the design of future experiments. Additionally, it provides a diverse set of data for validating more advanced implosion physics models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Verification of neoclassical toroidal viscosity induced by energetic particles

The thermal particles contributed neoclassical toroidal viscosity (NTV) have been successfully developed and explored by many impressive works such as the study by Shaing et al. [Phys. Plasmas 10, 1443 (2003)] and Zhu et al. [Phys. Rev. Lett. 96, 225002 (2006)]. In this work, the scope of the NTV study is extended to explore the contribution of energetic particles (EPs) through both theory and experiments. In theory, the existence of the NTV torque due to the precessional drift resonance of trapped EPs is identified based on the equivalence between the NTV torque and the perturbed drift kinetic energy [J. Park, Phys. Plasmas 18, 110702 (2011)]. Toroidal modeling with the Magneto Resistive Spectrum - drift Kinetic code [Y. Liu, Phys. Plasmas 15, 112503 (2008)], based on this equivalence, indicates that trapped EPs can contribute a significant amount of the NTV torque. Meanwhile, this work also focuses on developing the dedicated DIII-D experiments in the presence of the n = 2 external magnetic perturbation to verify the EP induced NTV (EP-NTV) by measuring the change of the NTV torque while varying the angle and the voltage of the neutral beam injection. However, the developed experiments have been unable to create conditions necessary to clearly demonstrate the presence of EP-NTV. The main challenge is separating the resonant and non-resonant momentum transport responses in the plasma. Finally, the experience, gained from this study, can help the further exploration of EP-NTV in the future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Validation of MARS-F modeling of plasma response to RMPs using internal measurements on DIII-D

The linear resistive plasma response model is validated against the plasma internal measurement data from DIII-D edge-localized mode (ELM) control experiments with applied resonant magnetic perturbation (RMP). Considered are DIII-D discharges where the n = 1, 2, and 3 (n is the toroidal mode number) RMP field was applied. Experimental data for the plasma boundary displacement, as well as the three-dimensional (3D) pressure perturbation in the edge pedestal region, are deduced from the vertical Thomson scattering (TS) system and the horizontal charge exchange recombination (CER) system on DIII-D. The linear response model produces results that are in reasonable quantitative agreement with the DIII-D internal measurements. The plasma boundary displacement of up to 15 mm is modeled, with the pedestal pressure perturbation reaching 3 kPa. As an important insight, the larger plasma displacement measured by the vertical TS system, as compared to that measured by the horizontal CER system, is due to the contribution from the tangential component of the plasma displacement to the former. This mixing of displacement components is also found to influence the sensitivity of the CER measurement comparisons. The results of this study provide further confidence in the linear resistive plasma response model for analyzing ELM control experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Interpretive MHD modeling of dispersive shell pellet injection for rapid shutdown in tokamaks

Dispersive shell pellet (DSP) injection is modeled with the extended-MHD code NIMROD for interpretive insight into the results of recent DIII-D DSP experiments and to explore the dynamics of an inside-out thermal quench for disruption mitigation in tokamaks. Simulations of the pre-thermal quench (TQ) phase indicate that the upper bound for the quantity of ablated carbon shell material that will not perturb the flux surfaces is in the ballpark of, but somewhat below the experimental quantity. Even below this quantity, sufficient electrons are added to the plasma by the shell material to produce significant dilution cooling before the TQ is triggered. Simulations carried through the end of the TQ have very large amplitude MHD fluctuations (δB/B>10 -2 ) at the time of the plasma current spike associated with current profile redistribution. Finally, after the plasma current spike, which is of comparable amplitude to that measured in DIII-D experiments, none of the runaway electron test-particles whose orbits are tracked throughout the simulation remain confined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Rapid cooling of the in-plane motion of two-dimensional ion crystals in a Penning trap to millikelvin temperatures

Here, we propose a highly feasible technique with no experimental overhead to rapidly cool the in-plane degrees of freedom of large two-dimensional ion crystals in Penning traps. Through simulations, we demonstrate that our approach enables the in-plane modes to cool down to a temperature of around 1 mK in less than 10 ms. Our technique relies on near-resonant coupling of the poorly cooled in-plane motions and the efficiently cooled out-of-plane motions, and is achieved without introducing additional potentials. The rapid cooling enabled by our approach is in contrast to typical operating conditions, where our simulations of the laser cooling dynamics suggest that the ion crystal's in-plane motion cools very slowly on a timescale of several hundreds of milliseconds, a rate likely slower than experimental heating rates. Our work sets the stage for sub-Doppler laser cooling of the planar motion, and more robust and versatile quantum simulation and quantum sensing experiments with two-dimensional crystals in Penning traps.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Stopping-power enhancement from discrete particle-wake correlations in high-energy-density plasmas

Three-dimensional (3D) simulations of electron beams propagating in high-energy-density plasmas using the quasistatic Particle-in-Cell (PIC) code QuickPIC demonstrate a significant increase in stopping power when beam electrons mutually interact via their wakes. Each beam electron excites a plasma wave wake of wavelength ~ 2 π c / ω p e , where c is the speed of light and ω p e is the background plasma frequency. Here we show that a discrete collection of electrons undergoes a beam-plasma-like instability caused by mutual particle-wake interactions that causes electrons to bunch in the beam, even for beam densities n b for which fluid theory breaks down. This bunching enhances the beam's stopping power, which we call “correlated stopping,” and the effect increases with the “correlation number” N b ≡ n b ( c / ω p e ) 3 . For example, a beam of monoenergetic 9.7 MeV electrons with N b = 1 / 8 , in a cold background plasma with n e = 10 26 cm – 3 (450 g cm – 3 DT), has a stopping power of 2.28 ± 0.04 times the single-electron value, which increases to 1220 ± 5 for N b = 64 . The beam also experiences transverse filamentation, which eventually limits the stopping enhancement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Combined Environments: Driving multiple loads on Z

Pulsed power drivers such as the Z generator of Sandia National Laboratories typically deliver high current (>20MA) to single experiments. This project is intended to develop and assess ways to simultaneously drive multiple targets on a single pulsed power driver (specifically a neutron and an x-ray producing target driven in a single experiment). The combined x-ray/neutron environment produced will then be used to investigate potential synergistic effects in integrated circuits. A pre-requisite for being able to design and study multiple targets on Z is first adapting simulation tools to be able to model them effectively. This will enable us to assess the tradeoffs between the different ways multiple targets can be combined, and to better understand how existing and future pulsed power machines can be used to generate combined testing environments. This report is limited to documenting the initial development of a parallel load modeling capability that is presently being applied to design experiments to produce combined neutron/x-ray environments on Z.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling ablator defects as a source of mix in high-performance implosions at the National Ignition Facility

Recent indirect drive inertial confinement fusion implosions on the National Ignition Facility (NIF) [Spaeth et al., Fusion Sci. Technol. 69, 25 (2016)] have crossed the threshold of ignition. However, performance has been variable due to several factors. One of the leading sources of variability is the quality of the high-density carbon (HDC) shells used as ablators in these experiments. In particular, these shells can have a number of defects that have been found to correlate with the appearance of ablator mix into the hot spot and a degradation in nuclear yield. These defects include pits on the ablator surface, voids in the ablator bulk, high-Z debris from the Hohlraum wall that adheres to the capsule surface, and finally the inherent granular micro-structure of the crystalline HDC itself. This paper summarizes high-resolution modeling of each of these mix sources in two recent high-performance NIF implosion experiments. The simulated impact from a range of individual capsule defects is found to be broadly consistent with the trends seen in experiment, lending credence to the modeling results and the details of the mixing process that they reveal. Interestingly, modeling of the micro-structure inherent to HDC shows that this perturbation source results in considerable mixing of the deuterium–tritium fuel with ablator material during the implosion. The reduction in fuel compression from this mix results in an approximately factor of two reduction in neutron yield in current implosions and emphasizes the importance of mitigating this significant performance degradation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Screening of resonant magnetic perturbation fields assuming various plasma flow models

A recently updated version of the MARS-F code [Y. Q. Liu et al., Phys. Plasmas 7, 3681 (2000); L. Li et al., Phys. Plasmas 25, 082512 (2018); and G. L. Xia et al., Nucl. Fusion 59, 126035 (2019)] is utilized to numerically investigate the plasma screening effect on the applied resonant magnetic perturbation (RMP) field, assuming various equilibrium flow models, including the toroidal flow, the parallel flow and their combinations, and poloidal and toroidal projections of the parallel flow. A parallel equilibrium flow with a uniform radial profile is found to have no effect on plasma screening of the RMP field. A sheared parallel flow, however, does change plasma screening. The poloidal projection of the parallel flow weakens plasma screening in the resistive-inertial regime. The effect on the favorable average curvature regime is found, however, to be non-monotonic. With the increasing flow speed, the poloidal projection first weakens Glasser-Green-Johnson (GGJ)-screening. Further increase in the flow speed results in enhanced GGJ-screening again. This non-monotonic behavior is related to the perturbed parallel shielding current, which appears also off the mode rational surface at fast flow due to additional resonances between the RMP perturbation and the sound wave continuum. These results indicate that flow induced plasma screening to the RMP field can have complicated characteristics, which, in turn, can have implications on the RMP field penetration into the plasma in experiments for controlling the edge localized modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

MX precipitate behavior in an irradiated advanced Fe-9Cr steel: Helium sequestration and cavity swelling performance

This work is the third and final part in an initial series on addressing the behavior of MX precipitate stability in an advanced Fe-9Cr reduced activation ferritic/martensitic (RAFM) alloy under fusion-relevant ion irradiation conditions. Here, the helium trapping properties of MX precipitates are investigated across varying damage levels (15–100 dpa), temperatures (400–600 °C), and helium doses (10–25 appm He/dpa) using sophisticated dual ion beam experiments and electron microscopy. Results indicate that individual MX precipitates efficiently sequester helium in the form of nanoscale bubbles at the precipitate-matrix interfaces near the peak swelling temperature (∼5 bubbles/precipitate at 500 °C). Swelling was primarily due to matrix cavities. The Fe-9Cr alloy reached 2% swelling by 100 dpa, suggesting a shift to steady-state swelling around 50 dpa at 500 °C. Furthermore, MX precipitate dissolution beginning at 15 dpa did not coincide with this onset of steady-state swelling.

Dual ion irradiation↗
DOE OSTI2021

Hohlraum x-ray preheat asymmetry measurement at the ICF capsule via Mo ball fluorescence imaging

In inertial confinement fusion, penetrating asymmetric hohlraum preheat radiation (>1.8 keV, which includes high temperature coronal M-band emission from laser spots) can lead to asymmetric ablation front and ablator–fuel interface hydrodynamic instability growth in the imploding capsule. First experiments to infer the preheat asymmetries at the capsule were performed on the National Ignition Facility for high density carbon (HDC) capsules in low density fill (0.3 mg/cc 4He) Au hohlraums by time resolved imaging of 2.3 keV fluorescence emission of a smaller Mo sphere placed inside the capsule. Measured Mo emission is pole hot (P2 > 0) since M-band is generated mainly by the outer laser beams as their irradiance at the hohlraum wall is 5× higher than for the inner beams. P2 has a large swing vs time, giving insight into the laser heated hohlraum dynamics. P4 asymmetry is small at the sphere due to efficient geometric smoothing of hohlraum P4 asymmetries at large hohlraum-to-capsule radii ratios. The asymmetry at the HDC capsule is inferred from the Mo emission asymmetry accounting for the Mo/HDC radius difference and HDC capsule opacity.

Dewald, E. L. (ORCID:0000000340546967)↗
DOE OSTI2020

Conceptual Design and Analysis of In-Vessel Components for the Materials Plasma Exposure eXperiment (MPEX)

The materials plasma exposure experiment (MPEX) is a linear plasma divertor simulator currently undergoing conceptual design. The facility will expose material samples to steady-state plasma fluxes to examine plasma–material interactions (PMIs) that are expected in the next generation of fusion devices. The plasmas will be generated by a helicon source, with electron and ion heating sources of up to 800 kW possible. The peak heat fluxes of the target are expected to be up to 10 MW/m 2 . The facility will be capable of handling low-activation neutron-irradiated samples in order to examine the multivariate effects of neutron damage and plasma fluence. Neutron-irradiated samples are planned to be roughly of 10-mm diameter; however, plasma-facing components up to 60×600 mm can be accommodated. The steady-state nature of the device will require the magnetic confinement of the plasma to be achieved with superconducting magnets, with a maximum on-axis field of 2.5 T. In addition, since MPEX will be a steady-state device, in-vessel components need to be water cooled. The primary in-vessel components will be the target, the dump plate, the limiter, the skimmers, and the microwave absorber. The conceptual design of these components is presented here, including analyses that confirm that the designs are adequate to meet the requirements of MPEX operation.

Lumsdaine, Arnold↗
DOE OSTI2020

An Overview of the Hybrid Illinois Device for Research and Applications Material Analysis Test-stand (HIDRA-MAT)

The Hybrid Illinois Device for Research and Applications (HIDRA) at the University of Illinois at Urbana-Champaign is a toroidal plasma device that enables fusion plasma-material interaction testing with both stellarator and tokamak plasmas. HIDRA’s long-pulse steady state stellarator plasmas provide a testbed for plasma facing component (PFC) plasma exposures. The HIDRA Material Analysis Test-stand (HIDRA-MAT) is a material characterization module attached to HIDRA that is being designed and fabricated to include thermal desorption spectroscopy and laser induced breakdown spectroscopy systems for in-vacuo PFC characterization. A specialized rotatable sample holder positions the sample for liquid metal droplet application from a liquid metal droplet injector on HIDRA-MAT. Early experiments look to investigate the effect liquid lithium has on porous tungsten samples’ retention of H, D, and He after plasma exposure. Preliminary results from a dual residual gas analyzer system show the ability to differentiate D2 and He in HIDRA-MAT. Finally, this work aims to advance the understanding of liquid metal PFCs and further the design and development of new fusion PFCs and technologies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗