Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

H2RG Detector Characterization for RIMAS and Instrument Efficiencies

The Rapid infrared IMAger-Spectrometer (RIMAS) is a near-infrared (NIR) imager and spectrometer that will quickly follow up gamma-ray burst afterglows on the 4.3-meter Discovery Channel Telescope (DCT). RIMAS has two optical arms which allows simultaneous coverage over two bandpasses (YJ and HK) in either imaging or spectroscopy mode. RIMAS utilizes two Teledyne HgCdTe H2RG detectors controlled by Astronomical Research Cameras, Inc. (ARC/Leach) drivers. We report the laboratory characterization of RIMAS's detectors: conversion gain, read noise, linearity, saturation, dynamic range, and dark current. We also present RIMAS's instrument efficiency from atmospheric transmission models and optics data (both telescope and instrument) in all three observing modes.

Toy, Vicki L.↗
NASA NTRS2020

Loads Correlation of a Full-Scale Proprotor on the Tiltrotor Test Rig

In 2018, a full-scale isolated proprotor test was conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames. The test article was the 3-bladed Bell 699 research rotor derived from the AW609 rotor. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. Correlations between the 2018 test data and predictions from the comprehensive analysis CAMRAD II for blade and yoke (flexbeam) loads and rotor torque are presented. The full range of conversion to helicopter modes is covered: conversion 30-, 45-, and 60-deg TTR yaw, and helicopter 75- and 90-deg TTR yaw. The flap moment correlation is reasonable to good; the pitch link load and torsion moment are uniformly underpredicted. The measured 2P lag moment and 2P torque are not captured by the analysis. The inability to predict the 2P component is currently attributed to the analytical assumption of a perfect gimbal, whereas the actual test gimbal may be operating imperfectly and thus introducing the 2P harmonic. A new analytical model that accounts for non-ideal gimbal operation is needed.

Kottapalli, Sesi↗
DOE OSTI2024

Californium-252 production at the High Flux Isotope Reactor - I: Validation study using campaign data

This paper presents a series of 252 Cf production validation and code-to-code comparison studies performed based on data from the production campaigns at the High Flux Isotope Reactor (HFIR). These studies support efforts to convert HFIR from using highly enriched uranium (HEU) fuel to low-enriched uranium (LEU) fuel. HFIR must maintain its world-class performance and missions following this conversion, and because 252 Cf is a vital neutron-emitting radioisotope used for a variety of high-impact applications (e.g., reactor startup, cancer treatment), the ability to efficiently produce 252 Cf must be preserved. In this work, the HFIRCON, Shift, ORIGEN, and TCOMP codes were deployed, and several sets of data libraries were investigated to better understand the calculation codes and the data biases. As-loaded target composition data, as-run irradiation history data, and post-irradiation measurements from recent multi-cycle irradiation campaigns of the HEU core were used to validate and determine methodology biases. Further, the findings demonstrated a good agreement, with results falling within 3 standard deviations of measurements. This paper lays the ground work for the second paper, which evaluates and compares 252 Cf production and safety metrics with the HEU core and a proposed LEU core.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2026

Author Correction: US oil and gas system emissions from nearly one million aerial site measurements

Correction to: Naturehttps://doi.org/10.1038/s41586-024-07117-5 Published online 13 March 2024 In the version of the article initially published, several errors were present and have been corrected in the HTML and PDF versions of the article and Supplementary Information. The main results, conclusions, and our interpretations of the data remain unchanged. See the new Supplementary Information Section S15 for a more detailed description of the errors corrected and the resulting effects on the analysis. Data processing and methods corrections Overflight count correction: We previously used pre-computed source coverage data for some Carbon Mapper campaigns that was computed differently than was required for our analysis. We have re-computed Carbon Mapper source coverage based on flightline polygons and source coordinates. Transition point computation, well sites: The updated version now correctly compares the cumulative emissions distribution of simulated well site emissions with that of aerially detected sources (rather than plumes) when computing the transition point. Transition point computation, midstream: Additionally, the transition point calculation has been corrected to exclude aerially detected midstream emissions below the transition point, which was previously leading to double counting of these emissions. This error was not present for upstream (well site) emissions. Calculation errors Unit error: We corrected a specific unit conversion error affecting well site emissions in the Kairos Fort Worth dataset. Across all datasets, we also correct the conversion factor for converting from standard volume to mass for midstream emissions. Sorting error: We correct code that was applying incorrect sorting when computing correction factors to account for partial detection at well sites. Small typographical corrections were made in Fig. 1b and SI Section S4.1. Data processing and methods corrections Overflight count correction: We previously used pre-computed source coverage data for some Carbon Mapper campaigns that was computed differently than was required for our analysis. We have re-computed Carbon Mapper source coverage based on flightline polygons and source coordinates. Transition point computation, well sites: The updated version now correctly compares the cumulative emissions distribution of simulated well site emissions with that of aerially detected sources (rather than plumes) when computing the transition point. Transition point computation, midstream: Additionally, the transition point calculation has been corrected to exclude aerially detected midstream emissions below the transition point, which was previously leading to double counting of these emissions. This error was not present for upstream (well site) emissions. Calculation errors Unit error: We corrected a specific unit conversion error affecting well site emissions in the Kairos Fort Worth dataset. Across all datasets, we also correct the conversion factor for converting from standard volume to mass for midstream emissions. Sorting error: We correct code that was applying incorrect sorting when computing correction factors to account for partial detection at well sites. Small typographical corrections were made in Fig. 1b and SI Section S4.1. The following practices may help researchers conducting similar analyses avoid making similar errors: 1, Clear, accessible documentation explaining the interpretation of all columns in data input tables and all internal variables within the model, 2, Simple cross-check calculations computed before and after unit conversions.

Sherwin, Evan D↗
NASA NTRS1985

Whistler-triggered VLF noise bursts observed on the DE-1 satellite and simultaneously at Antarctic ground stations

Simultaneous observations of whistler-triggered very low-frequency noise bursts on the ground at Anarctic stations, Halley and Siple, and on the high-altitude satellite DE-1 are reported. Results of a case study from June 25, 1982 in which the satellite data were recorded near 25 deg south magnetic latitude and the L = 4.7 magnetic shell, are presented. Analysis indicates that the chorus bursts that are triggered in whistler ducts travel downwards in the ducts to low altitudes in the ionosphere, and that propagation to DE-1 is by upward reflection into a nonducted mode. A means of estimating the propagation characteristics of the wave bursts is provided by comparisons of nonducted signals from the Siple transmitter and discrete periodic emissions. The ducted-nonducted mode conversion process is a mechanism for the large-scale spreading into the magnetosphere of coherent whistler-mode wave energy which is generated, amplified, or triggered in small localized ducts. The DE-1 data show that a strong interaction exists between whistler-triggered noise bursts and prevailing hiss levels.

Smith, A. J.↗
DOE OSTI2020

Hawai‘i National Marine Renewable Energy Center (HINMREC)

The Hawaii National Marine Renewable Energy Center (HINMREC) was established to facilitate the commercialization of wave energy converter (WEC) devices, and to accelerate development and testing of Ocean Thermal Energy Conversion (OTEC) technologies. Housed at the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii (UH), this program started with execution of the contract between the US Department of Energy (DOE) and UH in March 2009, and activities ran through the end of the project in September 2019. The DOE tasked HINMREC with facilitating and accelerating the build-out of the Navy’s Wave Energy Test Site (WETS), the nation’s first grid-connected open water wave energy conversion test facility, located off Marine Corps Base Hawaii (MCBH) in Kaneohe, on the island of Oahu. WETS was expanded from an existing test berth at 30m water depth to include test berths at 60m and 80m water depths. In recognition of the high costs associated with at-sea testing and evaluation of WEC devices, it was deemed imperative that HINMREC seek ways to reduce costs to developers by providing key research support to these early-stage technologies. WETS and HINMREC’s support allowed development of wave energy technology by providing a testing infrastructure that allows technology developers to test, demonstrate and evaluate their WEC devices, and generate data in order to advance WEC designs toward commercial readiness. HINMREC’s roles have included support in the establishment of the full site, including of wave resource characterization and site survey, followed by the essential roles of independent WEC device power performance assessment and environmental monitoring in support of deployed pre-commercial WECs. This DOE-funded work transitioned effectively to continue Navy-funded tasks for OTEC development, and activities at WETS, now under Naval Facilities Engineering Command (NAVFAC) funding. A secondary objective in the establishment of HINMREC was to assist the private sector in moving OTEC systems beyond proof-of-concept to pre-commercialization, primarily focused on system and component engineering, and local and global investigations into the potential environmental impacts of OTEC systems. HINMREC was tasked with maintaining high-resolution models of ocean thermal resources and the potential sustainable power output of OTEC systems. Ongoing tests begun previously under Navy funding at the OTEC Heat Exchangers (HXs) Test Facility at the Natural Energy Laboratory of Hawaii Authority (NELHA), in Kona on Hawaii Island, have been continued to identify cost-effective aluminum alloys for use in OTEC systems operating in the corrosive marine environment.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Opening pathways for the conversion of woody biomass into sustainable aviation fuel via catalytic fast pyrolysis and hydrotreating

Meeting aggressive decarbonization targets set by the International Civil Aviation Organization (ICAO) will require the rapid development of technologies to produce sustainable aviation fuel (SAF). Catalytic fast pyrolysis (CFP) can support these efforts by opening pathways for the conversion of woody biomass into an upgraded biogenic oil that can be further processed to SAF and other fuels. However, the absence of end-to-end experimental data for the process leads to uncertainty in the yield, product quality, costs, and sustainability of the pathway. The research presented here serves to address these needs through a series of integrated experimental campaigns in which real biomass feedstocks are converted to a final SAF product using large bench-scale continuous reactor systems. For these campaigns, the degree of catalytic upgrading during CFP was varied to produce CFP-oils with oxygen contents of 17 and 20 wt% on a dry basis. The CFP-oils were then hydrotreated and distilled into gasoline, diesel, and SAF fractions. Detailed yield and compositional data were obtained for each step of the process to inform technoeconomic and lifecycle analyses, and the fuel properties of the SAF fraction were evaluated to provide first-of-its-kind insight into the quality of the final product. This research reveals opportunities to optimize process carbon efficiency by tuning the degree of catalytic upgrading during the CFP step and highlights routes to produce a high-quality cycloalkane-rich SAF with 85–92% reduction in greenhouse gas emissions compared to fossil-based pathways.

09 BIOMASS FUELS↗
DOE OSTI2026

Data for "Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells"

Back contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl2 treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO3 using a combination of angle-resolved XPS and the cadmium modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO3 native oxide. The fate of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO3 alleviates the downward band bending by 40 meV from 470 meV to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy which shows losses in internal open circuit voltage (iVoc) from 820 meV to 795 meV, carrier lifetime from 123 ns to 45 ns, and PL quantum yield from 2.9x10-5 to 1.2x10-5. Modeling time-resolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
NASA NTRS1981

OCCULT-ORSER complete conversational user-language translator

Translator program (OCCULT) assists non-computer-oriented users in setting up and submitting jobs for complex ORSER system. ORSER is collection of image processing programs for analyzing remotely sensed data. OCCULT is designed for those who would like to use ORSER but cannot justify acquiring and maintaining necessary proficiency in Remote Job Entry Language, Job Control Language, and control-card formats. OCCULT is written in FORTRAN IV and OS Assembler for interactive execution.

Ramapriyan, H. K.↗
NASA NTRS1974

Intercomparison of ground-based and space solar flux measurements

Detailed temporal measurements of the solar flux at one location are performed. These data are then analyzed and compared to the potential of space measurements which allow one to consider the flux falling on areas of the earth. An important result of the research is that the temporal characteristics of the flux in the presence of a real atmosphere would be difficult to obtain from space and that the variations in the flux can be highly significant in regard to most solar conversion schemes. The detailed results of the research are presented. The instruments developed to separate the direct and scattered solar flux, the computer analysis methods developed, and the results of the research, presented as both graphical and tabular data, are discussed.

Meinel, A. B.↗
NASA NTRS1983

The association of energetic particles and shocks in the heliosphere

The observational and theoretical work on heliospheric shocks and cosmic rays in the recent past is surveyed. The data have come mainly from spacecraft in the regions from 0.3-25 AU, and include detection of particles and plasma waves upstream of the earth's bow shock. The theory of shock acceleration is reviewed, together with analytical models of energetic particle enhancement in association with shocks or shocks within the heliosphere. It has been determined that shocks in the heliosphere are associated with energetic suprathermal particles, which are conversely all associated with shocks. Solar cosmic rays and other anomalous components are therefore accelerated by shocks, a factor that is significant for studies of the acceleration mechanisms for galactic cosmic rays. The Solar Polar Mission will provide data on all solar latitudes, and the ISEE-3 spacecraft will continue to gather information on shock accelerated ions in travelling interplanetary shock waves.

Lee, M. A.↗
NASA NTRS2011

Determination of Barometric Altimeter Errors for the Orion Exploration Flight Test-1 Entry

The EFT-1 mission is the unmanned flight test for the upcoming Multi-Purpose Crew Vehicle (MPCV). During entry, the EFT-1 vehicle will trigger several Landing and Recovery System (LRS) events, such as parachute deployment, based on onboard altitude information. The primary altitude source is the filtered navigation solution updated with GPS measurement data. The vehicle also has three barometric altimeters that will be used to measure atmospheric pressure during entry. In the event that GPS data is not available during entry, the altitude derived from the barometric altimeter pressure will be used to trigger chute deployment for the drogues and main parachutes. Therefore it is important to understand the impact of error sources on the pressure measured by the barometric altimeters and on the altitude derived from that pressure. There are four primary error sources impacting the sensed pressure: sensor errors, Analog to Digital conversion errors, aerodynamic errors, and atmosphere modeling errors. This last error source is induced by the conversion from pressure to altitude in the vehicle flight software, which requires an atmosphere model such as the US Standard 1976 Atmosphere model. There are several secondary error sources as well, such as waves, tides, and latencies in data transmission. Typically, for error budget calculations it is assumed that all error sources are independent, normally distributed variables. Thus, the initial approach to developing the EFT-1 barometric altimeter altitude error budget was to create an itemized error budget under these assumptions. This budget was to be verified by simulation using high fidelity models of the vehicle hardware and software. The simulation barometric altimeter model includes hardware error sources and a data-driven model of the aerodynamic errors expected to impact the pressure in the midbay compartment in which the sensors are located. The aerodynamic model includes the pressure difference between the midbay compartment and the free stream pressure as a function of altitude, oscillations in sensed pressure due to wake effects, and an acoustics model capturing fluctuations in pressure due to motion of the passive vents separating the barometric altimeters from the outside of the vehicle.

Brown, Denise L.↗
NASA NTRS2012

The Characterization of Virgo Data and Its Impact on Gravitational-Wave Searches

Between 2007 and 2010 Virgo collected data in coincidence with the LIGO and GEO gravitational-wave (GW) detectors. These data have been searched for GWs emitted by cataclysmic phenomena in the universe, by non-axisymmetric rotating neutron stars or from a stochastic background in the frequency band of the detectors. The sensitivity of GW searches is limited by noise produced by the detector or its environment. It is therefore crucial to characterize the various noise sources in a GW detector. This paper reviews the Virgo detector noise sources, noise propagation, and conversion mechanisms which were identified in the three first Virgo observing runs. In many cases, these investigations allowed us to mitigate noise sources in the detector, or to selectively flag noise events and discard them from the data. We present examples from the joint LIGO-GEO-Virgo GW searches to show how well noise transients and narrow spectral lines have been identified and excluded from the Virgo data. We also discuss how detector characterization can improve the astrophysical reach of gravitational wave searches.

Characterization↗
NASA NTRS2001

End-to-End Demonstrator of the Safe Affordable Fission Engine (SAFE) 30: Power Conversion and Ion Engine Operation

The Safe Affordable Fission Engine (SAFE) test series addresses Phase 1 Space Fission Systems issues in particular non-nuclear testing and system integration issues leading to the testing and non-nuclear demonstration of a 400-kW fully integrated flight unit. The first part of the SAFE 30 test series demonstrated operation of the simulated nuclear core and heat pipe system. Experimental data acquired in a number of different test scenarios will validate existing computational models, demonstrated system flexibility (fast start-ups, multiple start-ups/shut downs), simulate predictable failure modes and operating environments. The objective of the second part is to demonstrate an integrated propulsion system consisting of a core, conversion system and a thruster where the system converts thermal heat into jet power. This end-to-end system demonstration sets a precedent for ground testing of nuclear electric propulsion systems. The paper describes the SAFE 30 end-to-end system demonstration and its subsystems.

Hrbud, Ivana↗
DOE OSTI2021

Deriving Simulation Parameters for Storage-Type Water Heaters Using Ratings Data Produced from the Uniform Energy Factor Test Procedure: Preprint

Building energy modeling (BEM) is commonly used to estimate the energy usage of residential buildings. Uses for BEM include calculating home energy ratings, demonstrating compliance with performance-based energy codes, and establishing whether designs meet voluntary program requirements, such as ENERGY STAR® qualified homes. BEM requires simulating subsystems within the building, including storage-type water heaters. To properly simulate the in-situ performance of residential storage water heaters, it is necessary to determine key water heater parameters, including the overall heat loss coefficient (UA) and conversion efficiency (?c) of the water heater, based on the rated efficiency of the water heater. The testing procedure and rating standard for residential water heaters have recently changed: the new rating standard provides a Uniform Energy Factor (UEF) rather than the Energy Factor (EF) used previously. This paper discusses how to derive the necessary model parameters from the ratings data produced from the latest test procedure.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Developing a Prototype Methodology to Rank CO2-EOR Wells and Assess Their Reuse Potential for Geologic Carbon Storage

This paper presents a prototype methodology to assess the possible transition of Class II carbon dioxide-enhanced oil recovery (CO2-EOR) wells to Class VI wells. The focus is on wellbore construction materials—casing, cement, tubing, and the packer—and includes comprehensive workflows to evaluate these materials, with primary emphasis on compliance with Environmental Protection Agency (EPA) Class VI well construction and conversion guidelines. These workflows systematically assess material properties and performance criteria to ensure regulatory compliance and optimize long-term wellbore integrity and functionality. Utilizing Python scripts and JavaScript Object Notation (JSON) representations, the study automates checks on digitized Texas Railroad Commission (TRRC) data to rank wells based on workflow criteria. By emphasizing critical factors such as casing integrity, cementing techniques, tubing compatibility, and packer selection, the methodology helps well owners and operators prioritize wells for potential reuse as CO2 injection wells. Given limitations in digitized data, manual user verification is required in some sections. Future improvements include integrating non-digitized data through web scraping and machine learning techniques. This research serves as a practical guide for stakeholders, supporting environmental compliance and sustainable well operations.

geologic carbon sequestration↗
DOE OSTI2021

Melting rate correlation with batch properties and melter operating conditions during conversion of nuclear waste melter feeds to glasses

The rate of conversion of nuclear waste melter feed to glass is affected by the selection of melter feed materials and by melter design and operation. The melting rate correlation (MRC) is an equation that relates the glass production rate with two types of variables: (1) feed and melt properties: conversion heat, cold-cap bottom temperature, and glass melt viscosity; and (2) melter design and operation parameters: melter geometry, melter operating temperature, and gas bubbling rate. The MRC shows good agreement for an extended melting-rate data set of high-level waste (HLW) melter feeds and a data set generated for low-activity waste (LAW) melter feeds. Laboratory observation of heated melter feed samples is often used to assess the cold-cap bottom temperature of HLW melter feeds (moderately foaming feeds), but this technique appears inadequate for LAW melter feeds (vigorously foaming feeds). For LAW feeds, an adequate assessment of the cold-cap bottom temperature was achieved using evolved gas analysis, which allows identification of the collapse of primary foam for oxidized feeds. This assessment shows that the cold-cap bottom temperature for vigorously foaming LAW feeds is higher than that for moderately foaming HLW feeds. When the results of MRC are compared, LAW feeds are generally less sensitive to the bubbling rate and melt viscosity, and more sensitive to the cold-cap bottom temperature than HLW feeds. The MRC qualifies as a promising tool to support the selection of melter feed materials and melter operating conditions, which is determined from expensive independent scaled melter experiments, and sophisticated mathematical models.

Lee, Seung Min↗