Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circular”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A temperature correlation for the radiation resistance of a thick-walled circular duct exhausting a hot gas

It is often useful to know the radiation impedance of an unflanged but thick-walled circular duct exhausting a hot gas into relatively cold surroundings. The reactive component is shown to be insensitive to temperature, but the resistive component is shown to be temperature dependent. A temperature correlation is developed permitting prediction of the radiation resistance from a knowledge of the temperature difference between the ambient air and the gas flowing from the duct, and a physical basis for this correlation is presented.

Mahan, J. R.↗
NASA NTRS1984

Compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage

An investigation of the compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage was conducted. Graphite-epoxy laminates consisting of all + or - 45-deg plies and of + or - 45-deg and 90-deg plies were evaluated. Inplane shearing between the fibers and matrix (i.e., matrix shearing) was found to be the primary compression failure mechanism for an all + or - 45-deg laminate with a hole. The failure mechanism for the + or 45-deg-dominated laminates with a hole appeared to be a combination of delamination and matrix shearing. The compression failure stresses and strains for both the all + or - 45-deg laminate and the + or - 45-deg-dominated laminates were unaffected by impact damage at an energy level of 5.5 J when compared to results for undamaged control specimens. The failure stresses and strains for all laminates with impact damage at an energy level of 17.0 J or of 34.3 J were significantly lower than the corresponding data for the undamaged control specimens. The failure stresses and strains for these impact-damaged specimens were independent of the percentage of 90-deg plies in the laminate.

Shuart, M. J.↗
NASA NTRS1984

Postbuckling behavior of axially compressed graphite-epoxy cylindrical panels with circular holes

The results of an experimental and analytical study of the effects of circular holes on the postbuckling behavior of graphite-epoxy cylindrical panels loaded in axial compression are presented. The STAGSC-1 general shell analysis computer code is used to determine the buckling and postbuckling response of the panels. The loaded, curved ends of the specimens were clamped by fixtures and the unloaded, straight edges were simply supported by knife-edge restraints. The panels are loaded by uniform end shortening to several times the end shortening at buckling. The unstable equilibrium path of the postbuckling response is obtained analytically by using a method based on controlling an equilibrium-path-arc-length parameter instead of the traditional load parameter. The effects of hole diameter, panel radius, and panel thickness on postbuckling response are considered in the study. Experimental results are compared with the analytical results and the failure characteristics of the graphite-epoxy panels are described.

Knight, N. F., Jr.↗
NASA NTRS1984

Wave multiple scattering by a finite number of unclosed circular cylinders

The boundary value problem of plane H-polarized electromagnetic wave multiple scattering by a finite number of unclosed circular cylinders is solved. The solution is obtained by two different methods: the method of successive scattering and the method of partial matrix inversion for simultaneous dual equations. The advantages of the successive scattering method are shown. Computer calculations of the suface currents and the total cross section are presented for the structure of two screens.

Veliyev, E. I.↗
NASA NTRS1984

Scattering from randomly oriented circular discs with application to vegetation

A vegetation layer is modeled by a collection of randomly oriented circular discs over a half space. The backscattering coefficient from such a half space is computed using the radiative transfer theory. It is shown that significantly different results are obtained from this theory as compared with some earlier investigations using the same modeling approach but with restricted disc orientations. In particular, the backscattered cross polarized returns cannot have a fast increasing angular trend which is inconsistent with measurements. By setting the appropriate angle of orientation to zero the theory reduces to previously published results. Comparisons are shown with measurements taken from milo, corn and wheat and good agreements are obtained for both polarized and cross polarized returns.

Karam, M. A.↗
NASA NTRS1984

Directional properties of circular Maria: Interpretation in the context of a testable gravitational capture model for lunar origin

Photogeologic study of circular lunar maria and mare-filled craters reveals that several of these features are either elliptical and/or asymmetrical. The ellipticity/asymmetry is interpreted as a directional property which may have genetic significance. Most maria indicate movement in easterly directions. The directional properties of these features are consistent with at least three models of mare basin formation: (1) mare basins were excavated by a swarm of fragments from a tidally disrupted planetary body impacting from a westerly direction; (2) mare basins were excavated by lunar satellites whose orbits decayed sufficiently to cause the satellites to impact onto the lunar surface from a westerly direction; and (3) basins were formed by the impact of large spheroids of lunar basalt onto the lunar surface from a westerly direction.

Malcuit, R. J.↗
NASA NTRS1985

Stress waves in an isotropic elastic plate excited by a circular transducer

Steady state harmonic stress waves in an isotropic elastic plate excited on one face by a circular transducer are analyzed theoretically. The transmitting transducer transforms an electrical voltage into a uniform normal stress at the top of the plate. To solve the boundary value problem, the radiation into a half-space is considered. The receiving transducer produces an electrical voltage proportional to the average spatially integrated normal stress over its face due to an incident wave. A numerical procedure is given to evaluate the frequency response at a receiving point due to a multiply reflected wave in the near field. Its stability and convergence are discussed. Parameterization plots which determine the particular wave whose frequency response has maximum magnitude compared with other multiple reflected waves are given for a range of values of dimensionless parameters. The effects of changes in the values of the parameters are discussed.

Karagulle, H.↗
NASA NTRS1985

A new statistic for the analysis of circular data in gamma-ray astronomy

A new statistic is proposed for the analysis of circular data. The statistic is designed specifically for situations where a test of uniformity is required which is powerful against alternatives in which a small fraction of the observations is grouped in a small range of directions, or phases.

Protheroe, R. J.↗
NASA NTRS1984

Circular waveguide bifurcation for asymmetric modes

An analytical solution for a circular waveguide bifurcation with incident TE(11)- and TM(11)-modes is presented using the residue calculus method. It is shown how the coupling between the TE(1n)- and TM(1n)-modes can be taken into account by expressing the coupling factor as a contour integral, which is the key step enabling the residue calculus method to be applied. Graphical results for the scattering matrix parameters of the junction are given for a range of waveguide radii of interest in the design of dual-mode coaxial prime focus feeds for paraboloidal antennas.

Schilling, H. W.↗
NASA NTRS1985

Vibrations of circular orthotropic plates in affine space

The vibration of an initially compressed plate having a circular geometry and orthotropy is examined in an affine space. The classical linear plate theory and Hamilton's principle are employed. The equations of motion of the plate are particularly simple in the chosen affine space, permitting a free-vibration study of the entire spectrum of composite materials with polar orthotropy. Approximate but very accurate standing-wave-type mode shapes are used in solving the essentially double eigenvalue problem to determine the effects of midplane forces on the vibration frequencies of the plate. The results indicate that the affine-space frequency increases with increasing stiffness ratio but decreases with increasing midplane compression. It is also discovered that, contrary to the trends observed for rectangular geometry and orthotropy by Oyibo (1981), Brunelle (1982), and Brunelle and Oyibo (1983), the affine-space frequency increases with increasing generalized Poisson's ratio.

Oyibo, G. A.↗
NASA NTRS1985

Finite element method for nonlinear forced vibrations of circular plates

Geometric nonlinearities for large amplitude free and forced vibrations of circular plates are investigated. Inplane displacement and inertia are included in the formulation. Finite element method is used. Harmonic force matrix for nonlinear forced vibration analysis is introduced and derived. Various out-of-plane and inplane boundary conditions are considered. The relations of amplitude - frequency ratio for different boundary conditions and various loads conditions are presented.

Decha-Umphai, K.↗
NASA NTRS1985

Circular-to-rectangular transition ducts for high-aspect ratio nonaxisymmetric nozzles

The next generation fighter aircraft will be equipped with nonaxisymmetric multifunction jet engine exhaust systems. The circular-to-rectangular transition duct employed in these systems has been made longer with the objective to maintain uniform flow. The weight of the exhaust system increases with increasing nozzle aspect ratio. The new design is to provide enhanced maneuvering and STOL performance. It is attempted to reduce the increase in weight as much as possible by new design strategies. The present paper has the objective to show through experimental data that the current design guidelines for transition ducts can be expanded so that shorter transitions are possible thereby reducing the nonaxisymmetric exhaust system weight penalty.

Burley, J. R., II↗
NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗
NASA NTRS1985

Computation of flow around a circular cylinder in a supercritical regime

Compressible flows around a circular cylinder in a supercritical regime at Mach number 0.3 have been calculated by using the Beam-Warming-Steger scheme based on the full Navier-Stokes equations with improved accuracy. The flow patterns are visualized extensively to observe the characteristics in this regime. The computations show that the flow at certain Reynolds numbers in a supercritical regime becomes rather steady and irregular with small drag coefficients. This may correspond to the experimental observations that the Strouhal number can not be measured clearly at a certain Reynolds number range in the supercritical regime.

Ishii, K.↗
NASA NTRS1985

Large deflections of circular isotropic membranes subjected to arbitrary axisymmetric loading

Circular membranes with fixed peripheral edges, subjected to arbitrary axisymmetric loading were analyzed. A single governing differential equation in terms of radial stress was used. This nonlinear governing equation was solved using the finite difference method in conjunction with Newton-Raphson method. Three loading cases, namely: (1) uniformly loaded membrane, (2) a membrane with uniform load over an inner portion, and (3) a membrane with ring load, were analyzed. Calculated central displacement and the central and edge radial stresses for uniformly loaded membrane, agreed extremely well with the classical solution.

Kelkar, A.↗
NASA NTRS1985

Circularly polarized microstrip antennas

A simple microstrip antenna can be made to radiate EM waves of any polarization, in particular, the circular polarization (CP) without any phasing network and power divider. A simple and accurate theory for this family of antennas was developed. However, the CP bandwidth, (CPBW) the bandwidth in which the axial ratio (AR) is less than a certain specified value, is very small. Most of the experimental designs were made for a feed placed along the diagonal of the patch. It is shown that there are practically infinitely many possible designs with different feed location. The speculation that other designs might give a wider bandwidth is clarified and an effective method for broadening the bandwidth is shown.

Lo, Y. T.↗
NASA NTRS1985

Stress concentration around a small circular hole in the HiMAT composite plate

Anisotropic plate theory is used to calculate the anisotropic stress concentration factors for a composite plate (AS/3501-5 graphite/epoxy composite, single ply or laminated) containing a circular hole. This composite material is used on the highly maneuverable aircraft technology (HiMAT) vehicle. It is found that the anisotropic stress concentration factor could be greater or less than 3 (the stress concentration factor for isotropic materials), and that the locations of the maximum tangential stress points could shift with the change of fiber orientation with respect to the loading axis. The effect of hole size on the stress concentration factor is examined using the Point Stress Criterion and the Averaged Stress Criterion. The predicted stress concentration factors based on the two theories compared fairly well with the measured values for the hole size 0.3175 cm (1/8 in). It is also found that through the lamination process, the stress concentration factor could be reduced drastically, indicating an improvement in structural performance.

Ko, W. L.↗