Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Experimental Demonstration of a Supersonic Spike Ejector

Spike diffusers are presented as a means to improve supersonic ejector efficiency via reduction in shock losses. Design, fabrication, and testing of an articulated prototype is described. Experimental results are compared to empirical performance curves representing the loci of optimal one- and two-stage conventional ejectors driven by dry air and discharging to atmosphere. Operated at a compression ratio of ~10 with all inputs equal, the spike ejector is shown to have achieved up to 2.19X and 1.83X the secondary mass throughput of the one- and two-stage references, respectively. This suggests the potential of spike diffusers to reduce ejector operating costs by ~50%.

wind tunnel↗
NASA NTRS1971

Hypersonic bodies of maximum drag for a given lift-to-drag ratio.

The problem considered in this paper is concerned with the aerodynamic design of the forebody shape of reentry vehicles in the blunt, homothetic, elliptic transversal contour, power-law longitudinal contour, raked-off configurational set. In particular, the forebody shape which maximizes the ratio of the forebody pressure drag to the free-stream dynamic pressure for a given lift-to-drag ratio and given geometric properties is determined. This problem is considered because recent survey articles indicate that its solution will provide useful qualitative design information about manned vehicles entering the earth's atmosphere from any of the foreseeable planetary missions. Single-integral equations relating the lift and drag in Newtonian hypersonic flow to the forebody geometry are derived and used to formulate the optimization problem which is solved by a direct numerical method.

Mcmillan, W., III↗
NASA NTRS2014

Conceptual Design Optimization of an Augmented Stability Aircraft Incorporating Dynamic Response and Actuator Constraints

Empirical sizing guidelines such as tail volume coefficients have long been used in the early aircraft design phases for sizing stabilizers, resulting in conservatively stable aircraft. While successful, this results in increased empty weight, reduced performance, and greater procurement and operational cost relative to an aircraft with optimally sized surfaces. Including flight dynamics in the conceptual design process allows the design to move away from empirical methods while implementing modern control techniques. A challenge of flight dynamics and control is the numerous design variables, which are changing fluidly throughout the conceptual design process, required to evaluate the system response to some disturbance. This research focuses on addressing that challenge not by implementing higher order tools, such as computational fluid dynamics, but instead by linking the lower order tools typically used within the conceptual design process so each discipline feeds into the other. In thisresearch, flight dynamics and control was incorporated into the conceptual design process along with the traditional disciplines of vehicle sizing, weight estimation, aerodynamics, and performance. For the controller, a linear quadratic regulator structure with constant gains has been specified to reduce the user input. Coupling all the disciplines in the conceptual design phase allows the aircraft designer to explore larger design spaces where stabilizers are sized according to dynamic response constraints rather than historical static margin and volume coefficient guidelines.

Welstead, Jason↗
DOE OSTI2021

INTEGRATE - Inverse Network Transformations for Efficient Generation of Robust Airfoil and Turbine Enhancements

The INTEGRATE (Inverse Network Transformations for Efficient Generation of Robust Airfoil and Turbine Enhancements) project is developing a new inverse-design capability for the aerodynamic design of wind turbine rotors using invertible neural networks. This AI-based design technology can capture complex non-linear aerodynamic effects while being 100 times faster than design approaches based on computational fluid dynamics. This project enables innovation in wind turbine design by accelerating time to market through higher-accuracy early design iterations to reduce the levelized cost of energy. INVERTIBLE NEURAL NETWORKS Researchers are leveraging a specialized invertible neural network (INN) architecture along with the novel dimension-reduction methods and airfoil/blade shape representations developed by collaborators at the National Institute of Standards and Technology (NIST) learns complex relationships between airfoil or blade shapes and their associated aerodynamic and structural properties. This INN architecture will accelerate designs by providing a cost-effective alternative to current industrial aerodynamic design processes, including: - Blade element momentum (BEM) theory models: limited effectiveness for design of offshore rotors with large, flexible blades where nonlinear aerodynamic effects dominate - Direct design using computational fluid dynamics (CFD): cost-prohibitive - Inverse-design models based on deep neural networks (DNNs): attractive alternative to CFD for 2D design problems, but quickly overwhelmed by the increased number of design variables in 3D problems AUTOMATED COMPUTATIONAL FLUID DYNAMICS FOR TRAINING DATA GENERATION - MERCURY FRAMEWORK The INN is trained on data obtained using the University of Marylands (UMD) Mercury Framework, which has with robust automated mesh generation capabilities and advanced turbulence and transition models validated for wind energy applications. Mercury is a multi-mesh paradigm, heterogeneous CPU-GPU framework. The framework incorporates three flow solvers at UMD, 1) OverTURNS, a structured solver on CPUs, 2) HAMSTR, a line based unstructured solver on CPUs, and 3) GARFIELD, a structured solver on GPUs. The framework is based on Python, that is often used to wrap C or Fortran codes for interoperability with other solvers. Communication between multiple solvers is accomplished with a Topology Independent Overset Grid Assembler (TIOGA). NOVEL AIRFOIL SHAPE REPRESENTATIONS USING GRASSMAN SPACES We developed a novel representation of shapes which decouples affine-style deformations from a rich set of data-driven deformations over a submanifold of the Grassmannian. The Grassmannian representation as an analytic generative model, informed by a database of physically relevant airfoils, offers (i) a rich set of novel 2D airfoil deformations not previously captured in the data , (ii) improved low-dimensional parameter domain for inferential statistics informing design/manufacturing, and (iii) consistent 3D blade representation and perturbation over a sequence of nominal shapes. TECHNOLOGY TRANSFER DEMONSTRATION - COUPLING WITH NREL WISDEM Researchers have integrated the inverse-design tool for 2D airfoils (INN-Airfoil) into WISDEM (Wind Plant Integrated Systems Design and Engineering Model), a multidisciplinary design and optimization framework for assessing the cost of energy, as part of tech-transfer demonstration. The integration of INN-Airfoil into WISDEM allows for the design of airfoils along with the blades that meet the dynamic design constraints on cost of energy, annual energy production, and the capital costs. Through preliminary studies, researchers have shown that the coupled INN-Airfoil + WISDEM approach reduces the cost of energy by around 1% compared to the conventional design approach. This page will serve as a place to easily access all the publications from this work and the repositories for the software developed and released through this pr...

aerodynamics↗
NASA NTRS1986

Riblets for aircraft skin-friction reduction

Energy conservation and aerodynamic efficiency are the driving forces behind research into methods to reduce turbulent skin friction drag on aircraft fuselages. Fuselage skin friction reductions as small as 10 percent provide the potential for a 250 million dollar per year fuel savings for the commercial airline fleet. One passive drag reduction concept which is relatively simple to implement and retrofit is that of longitudinally grooved surfaces aligned with the stream velocity. These grooves (riblets) have heights and spacings on the order of the turbulent wall streak and burst dimensions. The riblet performance (8 percent net drag reduction thus far), sensitivity to operational/application considerations such as yaw and Reynolds number variation, an alternative fabrication technique, results of extensive parametric experiments for geometrical optimization, and flight test applications are summarized.

Walsh, Michael J.↗
NASA NTRS2014

Creating a Test Validated Structural Dynamic Finite Element Model of the X-56A Aircraft

Small modeling errors in the finite element model will eventually induce errors in the structural flexibility and mass, thus propagating into unpredictable errors in the unsteady aerodynamics and the control law design. One of the primary objectives of the Multi Utility Technology Test-bed, X-56A aircraft, is the flight demonstration of active flutter suppression, and therefore in this study, the identification of the primary and secondary modes for the structural model tuning based on the flutter analysis of the X-56A aircraft. The ground vibration test-validated structural dynamic finite element model of the X-56A aircraft is created in this study. The structural dynamic finite element model of the X-56A aircraft is improved using a model tuning tool. In this study, two different weight configurations of the X-56A aircraft have been improved in a single optimization run. Frequency and the cross-orthogonality (mode shape) matrix were the primary focus for improvement, while other properties such as center of gravity location, total weight, and offdiagonal terms of the mass orthogonality matrix were used as constraints. The end result was a more improved and desirable structural dynamic finite element model configuration for the X-56A aircraft. Improved frequencies and mode shapes in this study increased average flutter speeds of the X-56A aircraft by 7.6% compared to the baseline model.

ground vibration test↗
NASA NTRS2017

Conceptual Feasibility Study of the Hyperloop Vehicle for Next-Generation Transport

The Hyperloop concept is proposed as a faster, cheaper alternative to high-speed rail and traditional short-haul aircraft. It consists of a passenger pod traveling through a tube under light vacuum while being propelled and levitated by a combination of permanent and electro-magnets. The concept addresses NASA's research thrusts for growth in demand, sustainability, and technology convergence for high-speed transport. Hyperloop is a radical departure from other advanced aviation concepts, however it remains an aeronautics concept that tackles the same strategic goals of low-carbon propulsion and ultra-effcient vehicles. System feasibility was investigated by building a multidisciplinary vehicle sizing model that takes into account aerodynamic, thermodynamic, structures, electromagnetic, weight, and mission analyses. The sizing process emphasized the strong coupling between the two largest systems: the tube and the passenger pod. The model was then exercised to examine Hyperloop from a technical and cost perspective. The structural sizing analysis of the travel tube demonstrates potential for signi cant capital cost reductions by considering an underwater route. Examination of varying passenger capacity indicates that the system can be operated with a wide range of passenger loads without significant change in operating expenses. Lastly, a high-level sizing study simulated variations in tube area, pressure, pod speed, and passenger capacity showing that there is a tube pressure that minimizes operating energy usage. The value of this optimal tube pressure is highly sensitive to numerous design details. These combined estimates of energy consumption, passenger throughput, and mission analyses all support Hyperloop as a faster and cheaper alternative to short-haul flights. The tools and expertise used to quantify these results also demonstrate how traditional aerospace design methods can be leveraged to handle the complex and coupled design process. Much of the technology development required for the Hyperloop is shared with next-generation aircraft. Furthermore, the substantial public interest and active commercial development make it an ideal candidate as an aircraft technology driver and test bed.

Hyperloop Vehicle↗
NASA NTRS2012

Laminar, Transitional, and Turbulent Heating on Mid Lift-to-Drag Ratio Entry Vehicles

The boundary-layer transition characteristics and convective aeroheating levels on mid lift-to-drag ratio entry vehicle configurations have been studied through wind tunnel testing. Several configurations were investigated, including elliptically-blunted cylinders with both circular and elliptically-flattened cross sections, biconic geometries based on launch vehicle dual-use shrouds, and parametrically-optimized analytic geometries. Vehicles of this class have been proposed for high-mass Mars missions, such as sample return and crewed exploration, for which the conventional sphere-cone entry-vehicle geometries of previous Mars missions are insufficient. Testing was conducted at Mach 6 over a range of Reynolds numbers sufficient to generate laminar, transitional, and turbulent flow. Transition onset locations - both straight-line and cross-flow - and heating rates were obtained through global phosphor thermography. Supporting computations were performed to obtain heating rates for comparison with the data. Laminar data and predictions agreed to well within the experimental uncertainty. Fully-turbulent data and predictions also agreed well. However, in transitional flow regions, greater differences were observed. Additional aerodynamic performance data were also generated through Modified-Newtonian analyses of the geometries.

Hollis, Brian R.↗
NASA NTRS2014

Creating a Test-Validated Finite-Element Model of the X-56A Aircraft Structure

Small modeling errors in a finite-element model will eventually induce errors in the structural flexibility and mass, thus propagating into unpredictable errors in the unsteady aerodynamics and the control law design. One of the primary objectives of the X-56A Multi-Utility Technology Testbed aircraft is the flight demonstration of active flutter suppression and, therefore, in this study, the identification of the primary and secondary modes for the structural model tuning based on the flutter analysis of the X-56A aircraft. The ground-vibration test-validated structural dynamic finite-element model of the X-56A aircraft is created in this study. The structural dynamic finite-element model of the X-56A aircraft is improved using a model-tuning tool. In this study, two different weight configurations of the X-56A aircraft have been improved in a single optimization run. Frequency and the cross-orthogonality (mode shape) matrix were the primary focus for improvement, whereas other properties such as c.g. location, total weight, and off-diagonal terms of the mass orthogonality matrix were used as constraints. The end result was an improved structural dynamic finite-element model configuration for the X-56A aircraft. Improved frequencies and mode shapes in this study increased average flutter speeds of the X-56A aircraft by 7.6% compared to the baseline model.

ground vibration test↗
NASA NTRS1999

Entry Guidance for the Reusable Launch Vehicle

The X-33 Advanced Technology Demonstrator is a half-scale prototype developed to test the key technologies needed for a full-scale single-stage reusable launch vehicle (RLV). The X-33 is a suborbital vehicle that will be launched vertically, and land horizontally. The goals of this research were to develop an alternate entry guidance scheme for the X-33 in parallel to the actual X-33 entry guidance algorithms, provide comparative and complementary study, and identify potential new ways to improve entry guidance performance. Toward these goals, the nominal entry trajectory is defined by a piecewise linear drag-acceleration-versus-energy profile, which is in turn obtained by the solution of a semi-analytical parameter optimization problem. The closed-loop guidance is accomplished by tracking the nominal drag profile with primarily bank-angle modulation on-board. The bank-angle is commanded by a single full-envelope nonlinear trajectory control law. Near the end of the entry flight, the guidance logic is switched to heading control in order to meet strict conditions at the terminal area energy management interface. Two methods, one on ground-track control and the other on heading control, were proposed and examined for this phase of entry guidance where lateral control is emphasized. Trajectory dispersion studies were performed to evaluate the effectiveness of the entry guidance algorithms against a number of uncertainties including those in propulsion system, atmospheric properties, winds, aerodynamics, and propellant loading. Finally, a new trajectory-regulation method is introduced at the end as a promising precision entry guidance method. The guidance principle is very different and preliminary application in X-33 entry guidance simulation showed high precision that is difficult to achieve by existing methods.

Lu, Ping↗
NASA NTRS1986

Investigation of chord ratio, stagger, decalage angle, and flap angle for dual wing configurations

Aerodynamical closely coupled dual wing configurations of unequal chords are investigated for medium speed general aviation applications. Vortex panel and momentum boundary layer analysis are utilized for the two-dimensional predictions. A multi-surface vortex lattice method is used for the three-dimensional predictions. In the process of searching for the highest lift to drag ratio upper airfoil to lower airfoil chord ratios, both greater than and less than one, are investigated in terms of stagger, decalage angle, and gap. With the optimum chord ratio, at the optimum stagger and gap, proper spanwise decalage distribution is shown to yield the lowest two dimensional drag results. Various wing taper ratios and wing twists are investigated to increase wing efficiency. Comparisons are made between optimized dual and optimized single wing configurations both with the same fuselage, stabilator surfaces, engines, payload, and fuel. The dual wing configuration is shown to have significantly less drag and hence longer range than the conventional single wing configuration.

Selberg, B. P.↗
NASA NTRS1996

Closed-Loop System Identification Experience for Flight Control Law and Flying Qualities Evaluation of a High Performance Fighter Aircraft

This paper highlights some of the results and issues associated with estimating models to evaluate control law design methods and design criteria for advanced high performance aircraft. Experimental fighter aircraft such as the NASA-High Alpha Research Vehicle (HARV) have the capability to maneuver at very high angles of attack where nonlinear aerodynamics often predominate. HARV is an experimental F/A-18, configured with thrust vectoring and conformal actuated nose strakes. Identifying closed-loop models for this type of aircraft can be made difficult by nonlinearities and high order characteristics of the system. In this paper, only lateral-directional axes are considered since the lateral-directional control law was specifically designed to produce classical airplane responses normally expected with low-order, rigid-body systems. Evaluation of the control design methodology was made using low-order equivalent systems determined from flight and simulation. This allowed comparison of the closed-loop rigid-body dynamics achieved in flight with that designed in simulation. In flight, the On Board Excitation System was used to apply optimal inputs to lateral stick and pedals at five angles at attack : 5, 20, 30, 45, and 60 degrees. Data analysis and closed-loop model identification were done using frequency domain maximum likelihood. The structure of identified models was a linear state-space model reflecting classical 4th-order airplane dynamics. Input time delays associated with the high-order controller and aircraft system were accounted for in data preprocessing. A comparison of flight estimated models with small perturbation linear design models highlighted nonlinearities in the system and indicated that the closed-loop rigid-body dynamics were sensitive to input amplitudes at 20 and 30 degrees angle of attack.

Murphy, Patrick C.↗
NASA NTRS2020

Tuning Neural Network Models for Improved Prediction of Boundary Layer Transition

Boundary layer transition can strongly impact flight vehicle performance as it influences surface skin friction and aerodynamic heating, making accurate transition prediction a key to designing next generation aircraft. Artificial neural networks (ANNs) have shown promise toward predicting laminar-turbulent transition based on linear stability correlations. The computational efficiency of ANNs and the substantially reduced user involvement in relation to direct computations based on the linear stability theory (LST) makes them an attractive methodology for integrating the LST based correlations in computational fluid dynamics codes. Tollmien-Schlichting (TS) waves correspond to the dominant transition mechanism in 2D or weakly 3D subsonic boundary layers, such as those encountered in general aviation applications. Improvements to neural network model accuracy in predicting the amplification rates of TS instability waves have been investigated by leveraging recent machine learning developments in conjunction with surrogate optimization techniques and via suitable augmentation of the data used to train the networks. The optimized models trained on the modified dataset reduced the average transition location errors on different airfoils at several flow conditions by 51% of the original manually-tuned network’s errors on the same flow cases. The actual transition locations were derived from the Langley Stability and Transition Analysis Code (LASTRAC).

Machine Learning↗
NASA NTRS1999

Closed-Loop System Identification Experience for Flight Control Law and Flying Qualities Evaluation of a High Performance Fighter Aircraft

This paper highlights some of the results and issues associated with estimating models to evaluate control law design methods and design criteria for advanced high performance aircraft. Experimental fighter aircraft such as the NASA High Alpha Research Vehicle (HARV) have the capability to maneuver at very high angles of attack where nonlinear aerodynamics often predominate. HARV is an experimental F/A-18, configured with thrust vectoring and conformal actuated nose strakes. Identifying closed-loop models for this type of aircraft can be made difficult by nonlinearities and high-order characteristics of the system. In this paper only lateral-directional axes are considered since the lateral-directional control law was specifically designed to produce classical airplane responses normally expected with low-order, rigid-body systems. Evaluation of the control design methodology was made using low-order equivalent systems determined from flight and simulation. This allowed comparison of the closed-loop rigid-body dynamics achieved in flight with that designed in simulation. In flight, the On Board Excitation System was used to apply optimal inputs to lateral stick and pedals at five angles of attack: 5, 20, 30, 45, and 60 degrees. Data analysis and closed-loop model identification were done using frequency domain maximum likelihood. The structure of the identified models was a linear state-space model reflecting classical 4th-order airplane dynamics. Input time delays associated with the high-order controller and aircraft system were accounted for in data preprocessing. A comparison of flight estimated models with small perturbation linear design models highlighted nonlinearities in the system and indicated that the estimated closed-loop rigid-body dynamics were sensitive to input amplitudes at 20 and 30 degrees angle of attack.

Murphy, Patrick C.↗
NASA NTRS2014

Investigation of Active Flow Control to Improve Aerodynamic Performance of Oscillating Wings

The objective of this effort is to design a promising active flow control concept on an oscillating airfoil for on-blade alleviation of dynamic stall. The concept must be designed for a range of representative Mach numbers (0.2 to 0.5) and representative reduced frequency characteristics of a full-scale rotorcraft. Specifications for a sweeping-jet actuator to mitigate the detrimental effects of retreating blade stall experienced by edgewise rotors in forward flight has been performed. Wind tunnel modifications have been designed to accommodate a 5x6 test section in the Oran W. Nicks Low Speed Wind Tunnel at Texas A&M University that will allow the tunnel to achieve Mach 0.5. The flow control design is for a two-dimensional oscillating VR-7 blade section with a 15- inch chord at rotor-relevant flow conditions covering the range of reduced frequencies from 0.0 to 0.15 and Mach numbers from 0.2 to 0.5. A Computational Fluid Dynamics (CFD) analysis has been performed to influence the placement of the flow control devices for optimal effectiveness.

Narducci, Robert P.↗
NASA NTRS1985

X-29 initial flight test results

It is announced that the X-29 forward-swept-wing (FSW) aircraft has been built, with flight testing under way and proceeding smoothly. The X-29 is a single-seat, single-engine supersonic aircraft that blends an optimized FSW, a close-coupled near-coplar canard, an F-5A forward fuselage module employing two side-mounted engine inlets, and a new aft fuselage. An F404-GE-400 engine with afterburner provides about 16,000 lb of thrust. The X-29 was designed to be near neutrally stable in the supersonic region to minimize drag; it becomes highly unstable transonically and subsonically, which dictates the use of a computerized fly-by-wire flight control system capable of stabilizing the aircraft. The X-29 advanced technology demonstrator began flight testing on Dec. 14, 1984; by Sept. 26, 1985, its envelope had been expanded to 0.75 Mach, 350 knots estimated airspeed, and 30,000 feet altitude. The aircraft has flown with very few problems and aerodynamic, structural, and control system results have correlated well with predictions. Areas where prediction and performance are not so well correlated are noted.

Ishmael, S. D.↗
NASA NTRS2024

Intrastep, Stage-Value Predictors for Diagonally-Implicit Runge-Kutta Methods

To better identify the necessary attributes of good stage-value predictors (SVPs), numerous SVPs are designed for an existing: ESDIRK4(3)7L[2]SA [26] and a new: ESDIRK4(3)8L[2]SA scheme.1 Both are stifflyaccurate, stage-order two, explicit, singly-diagonally implicit Runge–Kutta (ESDIRK) schemes. Tradeoffs are studied in the parameter spaces enforcing the constraints on accuracy, linear stability, nonlinear stability and coefficient size to determine which objectives correlate with effective predictors. The SVPs are tested on three challenging external aerodynamics problems [107 − 108 degrees of freedom (DoFs)], each with a different level of stiffness. The problems include two 3D airfoils simulations and one canonical turbulence simulation. All simulations use the compressible Navier-Stokes equations (CNSE). An entropy stable spectral collocation formulation is used for discretizing the spatial terms in the equations. Simulations are performed at a wide variety of temporal error tolerances. Problems that are sufficiently stiff (e.g., lax temporal error tolerances) benefit from SVPs designed with second-order accuracy and stability properties: A-stability, and L-stability, rather than high accuracy constraints. Simulations with modest stiffness (e.g., strict error tolerances) are better suited for SVPs designed using high accuracy constraints. Designing SVPs with enhanced stability properties is tedious but worthwhile. Simulation times are reduced with optimal SVPs by as much as 100% on some stages, with combined stepwise improvements of between 50 − 100% for both methods. A comparative study is performed with the two aforementioned methods as well as four other ESDIRKs. The newly designed ESDIRK4(3)8L[2]SA with γ ≈ 1/10, proves to be the most efficient of the six tested ESDIRK schemes simulating the CNSE.

Diagonally-Implicit Runge-Kutta↗
NASA NTRS1972

Nacelle-airframe interference at low supersonic Mach numbers.

The aerodynamic interference between the propulsion system and airframe for a low supersonic transport with wing-mounted nacelles is examined. Both a flowfield analysis and the equivalent body approach were used to predict the interference lift, drag, and pitching moment as functions of nacelle size, shape, and position. The results indicate that the interference lift and pitching moment, as well as drag, must be included in the analysis to properly assess the interference effects. In addition, the performance of the basic wing was found to play an important role in determining the effectiveness of the interference lift in reducing the net installation drag. Based on a conservative prediction, the interference effects can reduce the installed propulsion system drag to 40% of the isolated drag of the nacelles. Furthermore, including the interference effects in the optimization of the engine cycle from a thermodynamic and weight standpoint can result in a considerable reduction in the net propulsion system weight fraction (fuel plus engines) while increasing the optimum engine bypass ratio of a typical transport vehicle.

Bencze, D. P.↗