Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “active layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Why DA and DB white dwarfs do not show coronal activity and p-mode oscillations

The problems of nonradiative heating of outer atmospheric layers and p-mode oscillations in white dwarfs caused by acoustic waves generated in convective zones are discussed. These effects have been studied by calculating the cutoff periods for adiabatic and isothermal waves propagating in atmospheres of DA and DB stars with Teff greater than or equal 20,000 K and log g = 6-9. The obtained cutoff periods are approximately bounded by 0.01 and 40 sec for high- and low-gravity white dwarfs, respectively. Expected amplitudes of p-mode oscillations corresponding to trapped acoustic waves with small angular wave numbers are estimated, indicating that the amplitudes could be observed as Doppler shifts of spectral lines which might be detectable if adequate spectral resolution were available. The luminosity variations corresponding to these amplitudes are unlikely to be observable when all damping processes are accounted for. Results also indicate that the present theory of convection predicts some irregularities in the behavior of physical parameters.

Musielak, Z. E.↗
DOE OSTI2022

Hybrid RANS-LES of the Atmospheric Boundary Layer for Wind Farm Simulations: Preprint

Wind farm simulations often do not accurately represent wake-atmospheric boundary layer (ABL) interactions, blade boundary layer (BL) dynamics, and turbine-turbine interactions. In this work, we use Active Model Split (AMS), a new hybrid Reynolds-Averaged Navier Stokes (RANS)-large eddy simulation (LES) model, which is well suited to capture these effects because the model can (i) accurately simulate the ABL with the Coriolis effect, (ii) is accurate in adverse pressure gradients such as those near wind turbine blades, and (iii) has sufficiently low computational cost to simulate multiple turbines while resolving the blade BL. For simplicity and consistency we develop AMS to be used throughout the domain rather than in a zonal method. We implement our work in the massively parallel flow solver, Nalu-Wind, so that our model can access the compute resources needed for blade-resolved simulations of multiple wind turbines. To accomplish these aims, we modify the baseline AMS by changing the RANS contribution to SST k - omega with a length scale limiter, adding the Coriolis effect, and developing an appropriate wall treatment. We show that AMS of the ABL with the Coriolis effect matches LES reference results better than those obtained with RANS. We describe our plans to add buoyancy effects and wind turbines to our AMS simulations.

atmospheric boundary layer↗
DOE OSTI2020

Understanding Charge Storage in Hydrated Layered Solids MOPO 4 (M = V, Nb) with Tunable Interlayer Chemistry

Hydrated layered solids are interesting charge storage hosts with potentially high electrochemical activity and interlayer tunability. Although it is often possible to tune their interlayer distance by a pillaring strategy, the poor electrochemical stability of such artificial structures remains a major issue in device operation. Here we investigate the charge storage properties of MOPO 4 (M = V, Nb) hydrates with a nanosheet morphology to understand the influence of the interlayer environment on cycling stability, as well as ion selectivity. While in hydrated VOPO 4 interlayer H 2 O molecules act as compressible springs to enable fast Li-/Na-ion transport kinetics and reasonable structural reversibility, NbOPO 4 layers with bridging PO 4 groups serving as permanent linkers exhibit highly stable cyclability for Li-ions, owing to a zero-volume-change ion transport process. However, the latter suffers from a much larger migration energy barrier for Na-ions. Lastly, our findings not only highlight a structurally intriguing material system, but also provide insights into reviving materials with an originally unstable interlayer chemical environment, and shed light on the design principles for creating electrochemically stable charge storage hosts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Vectorial Charge Transfer across Bipolar Membrane Loaded with CdS and Au Nanoparticles

Bipolar membranes (BPMs) which consist of a cation exchange layer (CEL) and anion exchange layer (AEL) are quite effective as membranes in gas phase electrolyzers. However, such membranes can also serve as a host to embed photocatalysts and electrocatalysts. By selectively exchanging cations with Cd 2+ and anions with AuCl 4 – , we were able to synthesize CdS and Au nanoparticles in CEL and AEL layers, respectively, through sequential chemical and photocatalytic reactions. Reacting Cd 2+ with thioacetamide formed the CdS nanoparticles in CEL. The photogenerated electrons from CdS were then used to reduce AuCl4– in an H-cell configuration to produce Au nanoparticles in AEL and thus prepare a photocatalytically active BPM film (referred to as a CdS/BPM/Au film). Such a concerted design of BPM allows “vectorial” electron transfer between two layers of BPM leading to its transfer to an acceptor molecule (methyl viologen) in solution. Designing photocatalytically active BPM and understanding the vectorial electron flow between two separate ion-selective layers offer new opportunities in water splitting and CO 2 reduction.

13 HYDRO ENERGY↗
NASA NTRS2017

Electric Field Activated Shape Memory Polymer Composite

Provided is an electrically activated shape memory polymer composite capable of thermal shape reformation using electric power to heat the composite through its matrix glass transition temperature. The composite includes an adaptable polymer matrix component using a diglycidyl ether resin, at least one substantially well-dispersed conductive or magnetic nano-filler component, and at least one elastic, laminated layer. Also provided are methods of preparing the composite and methods of activating the composite. A shape reformation of the composite is triggered by applying an electric field at DC and/or at a frequency above about 1.mu.Hz for a sufficient time.

Kang, Jin Ho↗
NASA NTRS1984

A comparison between active and passive sensing of soil moisture from vegetated terrains

A comparison between active and passive sensing of soil moisture over vegetated areas is studied via scattering models. In active sensing three contributing terms to radar backscattering can be identified: (1) the ground surface scatter term; (2) the volume scatter term representing scattering from the vegetation layer; and (3) the surface volume scatter term accounting for scattering from both surface and volume. In emission three sources of contribution can also be identified: (1) surface emission; (2) upward volume emission from the vegetation layer; and (3) downward volume emission scattered upward by the ground surface. As ground moisture increases, terms (1) and (3) increase due to increase in permittivity in the active case. However, in passive sensing, term (1) decreases but term (3) increases for the same reason. This self conpensating effect produces a loss in sensitivity to change in ground moisture. Furthermore, emission from vegetation may be larger than that from the ground. Hence, the presence of vegetation layer causes a much greater loss of sensitivity to passive than active sensing of soil moisture.

Fung, A. K.↗
NASA NTRS1985

A comparison between active and passive sensing of soil moisture from vegetated terrains

A comparison between active and passive sensing of soil moisture over vegetated areas is studied via scattering models. In active sensing three contributing terms to radar backscattering can be identified: (1) the ground surface scatter term; (2) the volume scatter term representing scattering from the vegetation layer; and (3) the surface volume scatter term accounting for scattering from both surface and volume. In emission three sources of contribution can also be identified: (1) surface emission; (2) upward volume emission from the vegetation layer; and (3) downward volume emission scattered upward by the ground surface. As ground moisture increases, terms (1) and (3) increase due to increase in permittivity in the active case. However, in passive sensing, term (1) decreases but term (3) increases for the same reason. This self compensating effect produces a loss in sensitivity to change in ground moisture. Furthermore, emission from vegetation may be larger than that from the ground. Hence, the presence of vegetation layer causes a much greater loss of sensitivity to passive than active sensing of soil moisture.

Fung, A. K.↗
DOE OSTI2020

A combined SECM and electrochemical AFM approach to probe interfacial processes affecting molecular reactivity at redox flow battery electrodes

Redox flow batteries are attractive technologies for grid energy storage since they use solutions of redox-active molecules that enable a superior scalability and the decoupling of power and energy density. However, the reaction mechanisms of the redox active components at RFB electrodes are complex, and there is currently a pressing need to understand how interfacial processes impact the kinetics and operational reversibility of RFB systems. Here, we developed a combined electrochemical imaging methodology rooted in scanning electrochemical microscopy (SECM) and atomic force microscopy (AFM) for exploring the impact of electrode structure and conditioning on the electron transfer properties of model redox-active dialkoxybenzene derivatives, 2,5-di-tert-butyl-1,4-bis(2-methoxyethoxy)benzene (C1) and 2,3-dimethyl-1,4-dialkoxybenzene (C7). Using AFM and secondary-ion mass spectrometry (SIMS), we observed the formation of interfacial films with distinct mechanical properties compared to those of cleaved graphitic surfaces, and exclusively during reduction of electrogenerated radical cations. These films had an impact on the median rate and distribution of the electron transfer rate constant at the basal plane of multilayer and single layer graphene electrodes, displaying kinetically-limited values that did not yield the activation expected per the Butler–Volmer model with a transfer coefficient ~0.5. These changes were dependent on redoxmer structure: furthermore, SECM showed strong attenuation of C7 kinetics by a surface layer on MLG and SLG, while C1 kinetics were only affected by SLG. SECM and AFM results together show that these limiting films operate exclusively on the basal plane of graphite, with the edge plane showing a relative insensitivity to cycling and operation potential. Ultimately, this integrated electrochemical imaging methodology creates new opportunities to understand the unique role of interfacial processes on the heterogeneous reactivity of redoxmers at electrodes for RFBs, with a future role in elucidating phenomena at high active concentrations and spatiotemporal variations in electrode dynamics.

25 ENERGY STORAGE↗
DOE OSTI2023

Giant Increase of Hardness in Silicon Carbide by Metastable Single Layer Diamond-Like Coating

Silicon carbide (SiC) is one of the hardest known materials. Its exceptional mechanical properties combined with its high thermal conductivity make it a very attractive material for a variety of technological applications. Recently, it was discovered that two-layer epitaxial graphene films on SiC can undergo a pressure activated phase transition into a sp3 diamene structure at room temperature. Here, we show that epitaxial graphene films grown on SiC can increase the hardness of SiC up to 100% at low loads (up to 900 µN), and up to 30% at high loads (10 mN). By using a Berkovich diamond indenter and nanoindentation experiments, we demonstrate that the 30% increase in hardness is present even for indentations depths of 175 nm, almost three hundred times larger than the graphene film thickness. The experiments also show that the yield point of SiC increases up to 77% when the SiC surface is coated with epitaxial graphene. These improved mechanical properties are explained with the formation of diamene under the indenter’s pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Low-Voltage Layered Na 2 TiGeO 5 Anode for Lithium-Ion Battery

Titanium-based anode materials have achieved much progress with the wide studies in lithium-ion batteries. However, these known materials usually possess high discharge voltage platforms and limited energy densities. In this work, a titanium-based oxide of Na 2 TiGeO 5 with layered structure, two-dimensional lamellar frame and exposed highly active (001) facet, exhibiting good electrochemical performance in terms of high capacity (410 mAh g –1 with a current density of 50 mA g –1 ), excellent rate capability and cycling stability with no obvious capacity attenuation after 4000 cycles, is reported. The appropriate discharge voltage plateau at around 0.2 V endows the Na 2 TiGeO 5 anode material high security compared with graphite and high energy density compared with spinel Li 4 Ti 5 O 12 . Combining the electrochemical tests and the density functional theory calculations, the Li + storage mechanism of Na 2 TiGeO 5 is elucidated and the conversion reaction process is revealed. More importantly, this study provides a way to develop low-voltage and high-capacity titanium-based anode materials for efficient energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Unconventional pressure-induced magnetic transitions and mechanical properties in non-magnetic LaFeSi

Here, this work demonstrates that two consecutive magnetic transitions occur in non-magnetic LaFeSi compound under negative hydrostatic pressure (small volume expansion). Electronic structure properties of LaFeSi were calculated using density functional theory (DFT) to understand the origin of these magnetic transitions. Mechanical properties of LaFeSi, especially elastic properties (shear and Young’s modulus, and Poisson’s ratio), were determined by DFT distortion calculations to elucidate lattice anisotropy and stability. The antiferromagnetic transition at –7.52 GPa, predicted in our work for LaFeSi, is consistent with the reported experimentally observed antiferromagnetic ground states in CeMnSi and LaMnSi compounds having similar crystal geometry. This finding of unexpected magnetic ordering predicts that layered non-magnetic materials, like LaFeSi, may become magnetically active with lattice expansion.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Decoupling Lattice and Magnetic Instabilities in Frustrated CuMnO2

The AMnO 2 delafossites (A = Na, Cu) are model frustrated antiferromagnets, with triangular layers of Mn 3+ spins. At low temperatures (T N = 65 K), a C2/m → P$\bar1$ transition is found in CuMnO 2 , which breaks frustration and establishes magnetic order. In contrast to this clean transition, A = Na only shows short-range distortions at T N . Here, we report a systematic crystallographic, spectroscopic, and theoretical investigation of CuMnO 2 . We show that, even in stoichiometric samples, nonzero anisotropic Cu displacements coexist with magnetic order. Using X-ray/neutron diffraction and Raman scattering, we show that high pressures act to decouple these degrees of freedom. This manifests as an isostuctural phase transition at ~10 GPa, with a reversible collapse of the c-axis. This is shown to be the high-pressure analogue of the c-axis negative thermal expansion seen at ambient pressure. Density functional theory (DFT) simulations confirm that dynamical instabilities of the Cu + cations and edge-shared MnO 6 layers are intertwined at ambient pressure. However, high pressure selectively activates the former, before an eventual predicted reemergence of magnetism at the highest pressures. Our results show that the lattice dynamics and local structure of CuMnO 2 are quantitatively different from nonmagnetic Cu delafossites and raise questions about the role of intrinsic inhomogeneity in frustrated antiferromagnets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Impact of surface hydrophilicity on the ordering and transport properties of bicontinuous microemulsions

Microemulsions (MEs) have many industrial applications, where recent developments have shown that MEs can be utilized for electrochemical applications, including potentially in redox flow batteries. However, understanding the structure and dynamics of these systems, including at a surface, is needed to direct and rationally control their electrochemical behavior. While bulk solution measurements have provided insight into their structure, their assembly at an interface also impacts the electron (to the electrode) and ion (across the surfactant) charge transfer processes in the system. To address this shortcoming, neutron reflectivity experiments and molecular simulations have been completed that document the near surface structure of a series of deuterated water (D 2 O)/polysorbate-20/toluene MEs on hydrophilic and amphiphilic surfaces. These results show that the microemulsions form complex layered structures near a hard electrode surface, where most layers are not purely one component. Decreasing the D 2 O concentration in the ME increases the number of and purity of the layers established on the solid surface. These lamellar-type layers transition from the surface to the bulk microemulsion as a series of mixed layers (i.e., containing oil, water, and surfactant) that are consistent with perforated lamellae. Additionally, these mixed lamellae appear to become more perforated with oil and water pathways on an amphiphilic surface. Furthermore, the purity and thickness of these layers will influence the accessibility of an electrode by redox active species, as well as ion transport required to satisfy the electroneutrality condition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Strain- and thickness-dependent magnetic properties of epitaxial La 0.67 Sr 0.33 CoO 3 /La 0.67 Sr 0.33 MnO 3 bilayers

Magnetic properties and interfacial phenomena of epitaxial perovskite oxides depend sensitively on parameters such as film thickness and strain state. In this work, epitaxial La0 .67 Sr 0.33 CoO 3 (LSCO)/La 0.67 Sr 0.33 MnO 3 (LSMO) bilayers were grown on NdGaO 3 (NGO) and LaAlO 3 (LAO) substrates with a fixed LSMO thickness of 6 nm, and LSCO thickness (t LSCO ) varying from 2 to 10 nm. Soft x-ray magnetic spectroscopy revealed that magnetically active Co 2+ ions that strongly coupled to the LSMO layer were observed below a critical t LSCO for bilayers grown on both substrates. On LAO substrates, this critical thickness was 2 nm, above which the formation of Co 2+ ions was quickly suppressed leaving only a soft LSCO layer with mixed valence Co 3+ /Co 4+ ions. The magnetic properties of both LSCO and LSMO layers displayed strong t LSCO dependence. This critical t LSCO increased to 4 nm on NGO substrates, and the magnetic properties of only the LSCO layer displayed t LSCO dependence. A non-magnetic layer characterized by Co 3+ ions and with a thickness below 2 nm exists at the LSCO/substrate interface for both substrates. Therefore, the results contribute to the understanding of interfacial exchange spring behavior needed for applications in next generation spintronic and magnetic memory devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Magnetic damping in ferromagnetic/heavy-metal systems: The role of interfaces and the relation to proximity-induced magnetism

Damping and spin transport in spintronic multilayered systems continues to be a topic of active research. The enhancement of damping in ferromagnet (FM)/spacer layer (SL)/heavy-metal (HM) thin-film systems was studied for Co 25 Fe 75 /SL/Pt with a nonmagnetic (NM) SL of either Au or Cu with variable thickness, in order to understand the correlation with proximity-induced magnetism (PIM) in the HM. Structural, PIM and magnetic damping measurements were undertaken on the same samples. Specifically, secondary ion mass spectroscopy, element specific x-ray magnetic reflectivity and x-ray magnetic circular dichroism at the Pt and Au L 3 edges, and ferromagnetic resonance methods were used. With increasing thickness of a Cu or Au SL directly between the FM and the Pt layer, the Pt PIM and the damping both fall rapidly, with a relationship between damping and PIM that depends on the SL material. The PIM observed in the Au layer showed a complex dependence on the layer thickness, suggesting some hybridization with the Pt. The role of the number and location of interfaces on the damping was demonstrated with the addition of a SL within the Pt layer, which showed that the specific details of the NM/HM interface also affects the damping. The insertion of a Cu SL within the Pt showed a measurable increase in the overall enhancement of the damping while the insertion of a Au SL into Pt had almost no effect on the damping. Finally, together these results demonstrate the role of both PIM and of additional interfaces in the enhancement of damping in FM/HM systems, which is not fully accounted for by existing theory

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

CryoTARPOS Vibration Mitigation System for Layered Experiments

The goal of this project is to implement a system that can eliminate or mitigate vibration so that clear images can be taken without bypassing the cryocooler. By allowing for layer characterization and cryocooler operation at the same time, cooling capacity and thermal stability of the target would be improved, and more layer characterization data could be taken. Increased cooling capacity and thermal stability could allow for layering during occasional off normal conditions that would typically result in a loss of temperature control and NIF operational delays ranging from several hours to several days per month. The increased cooling capacity and thermal stability could also allow for layering of new target platforms that have less cooling margin. Additional layer images could be used for better characterization of defects and non-uniformities in the layer and would reduce the likelihood of layer seed loss, which typically adds ~12 hours per week in layering time. Motion blur from vibration due to off normal activity in the NIF Target Bay could also be mitigated that would usually result in NIF operational delays of several hours every month.

42 ENGINEERING↗
DOE OSTI2022

Marine Shallow Cloud Adjustments to the Presence of Shortwave-Absorbing Aerosols: Advancing Understanding Through a Combined Analysis of Lasic Datasets and Process Modeling (Final Report)

This is a final report for this award, whose purpose was to support the analysis of data emanating from the LASIC (Layered Atlantic Smoke Interaction with Clouds) campaign. (Layered Atlantic Smoke Interactions with Clouds) is a strategy to improve our understanding of aged carbonaceous aerosol, its seasonal evolution, and the mechanisms by which clouds adjust to the presence of the aerosol. The observational strategy centers on deploying the AMF1 cloud, aerosol, and atmospheric profiling instrumentation to Ascension Island, located within the trade-wind shallow cumulus regime (14.50W, 80S) 3000 km offshore of continental Africa. The location is within the latitude zone of the maximum outflow of aerosol, with the deepening boundary layer known to entrain free-tropospheric smoke. The primary activities for LASIC are: 1) to improve current knowledge on aged biomass burning aerosol and its radiative properties as a function of the seasonal cycle; 2) to use surface-based remote sensing to sensitively interrogate the atmosphere for the relative vertical location of aerosol and clouds; 3) to improve our understanding of the cloud adjustments to the presence of shortwave-absorbing aerosol within the vertical column, both through aerosol-radiation and through aerosol-cloud interactions; 4) to aid low cloud parameterization efforts for climate models. This award serves to further these activities and includes a sub-award to Dr. Pablo Saide at UCLA for activities 3) and 4).

54 ENVIRONMENTAL SCIENCES↗