Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIND TUNNELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

VUV shock layer radiation in an arc-jet wind tunnel experiment

Measurements were made of the radiating gas cap of a blunt body in a NASA-Ames 20 MW arc-jet wind tunnel. The test gas was air. Spectra of the flux incident on a small aperture centered at the stagnation region were obtained. A helium-cooled, magnesium fluoride window transmitted the flux into an evacuated collimating system that focused the aperture onto the entrance slit of a spectrometer. Data were obtained with films and by photomultipliers. The spectral ranges covered were the vacuum ultraviolet, VUV, (120 nm to 200 nm) and the ultraviolet to near infrared (200 nm to 900 nm) with resolutions from 0.05 nm to 0.5 nm. This paper presents the preliminary VUV results from the experiment. Results from the 200 nm to 900 nm spectral range have been presented elsewhere. Representative spectral records from 120 nm to 200 nm are shown. The intense atomic oxygen and nitrogen lines which are of concern to hypersonic flight are measured. Carbon lines are are also seen. These results will be used to help develop and validate aerothermodynamic computational models of arc-jet wind tunnel performance and help to assess the importance of VUV heating to entering spacecraft.

Craig, Roger A.↗
NASA NTRS2002

Boundary Layer Transition on Slender Cones in Conventional and Low Disturbance Mach 6 Wind Tunnels

An experimental investigation was conducted on a 5-degree half-angle cone and a 5-degree half-angle flared cone in a conventional Mach 6 wind tunnel to examine the effects of facility noise on boundary layer transition. The influence of tunnel noise was inferred by comparing transition onset locations determined from the present test to that previously obtained in a Mach 6 low disturbance quiet tunnel. Together, the two sets of experiments are believed to represent the first direct comparison of transition onset between a conventional and a low disturbance wind tunnel using a common test model and transition detection technique. In the present conventional hypersonic tunnel experiment, separate measurements of heat transfer and adiabatic wall temperatures were obtained on the conical models at small angles of attack over a range of Reynolds numbers, which resulted in laminar, transitional, and turbulent flow. Smooth model turbulent heating distributions are compared to that obtained with transition forced via discrete surface roughness. The model nosetip radius was varied to examine the effects of bluntness on transition onset. Despite wall to total temperature differences between the transient heating measurements and the adiabatic wall temperature measurement, the two methods for determining sharp cone transition onset generally yielded equivalent locations. In the 'noisy' mode of the hypersonic low disturbance tunnel, transition onset occurred earlier than that measured in the conventional hypersonic tunnel, suggesting higher levels of freestream acoustic radiation relative to the conventional tunnel. At comparable freestream conditions, the transition onset Reynolds number under low disturbance conditions was a factor of 1.3 greater than that measured on flared cone in the LaRC conventional hypersonic tunnel and a factor of 1.6 greater that the flared cone run in the low disturbance tunnel run 'noisy'. Navier-Stokes mean flow computations and linear stability analysis were conducted to assess the experimental results and have indicated N factors associated with sharp flared cone transition onset to be approximately a factor of 2 lower than that inferred from the corresponding low disturbance tunnel measurements.

Horvath, Thomas J.↗
NASA NTRS1979

Two dimensional aerodynamic interference effects on oscillating airfoils with flaps in ventilated subsonic wind tunnels

The numerical computation of unsteady airloads acting upon thin airfoils with multiple leading and trailing-edge controls in two-dimensional ventilated subsonic wind tunnels is studied. The foundation of the computational method is strengthened with a new and more powerful mathematical existence and convergence theory for solving Cauchy singular integral equations of the first kind, and the method of convergence acceleration by extrapolation to the limit is introduced to analyze airfoils with flaps. New results are presented for steady and unsteady flow, including the effect of acoustic resonance between ventilated wind-tunnel walls and airfoils with oscillating flaps. The computer program TWODI is available for general use and a complete set of instructions is provided.

Fromme, J.↗
NASA NTRS1991

Evaluation of a three-dimensional Navier-Stokes solver for transonic flow over a low-aspect-ratio wing mounted in a wind tunnel

A three dimensional Navier-Stokes solver is evaluated for transonic flow over a thin, swept, low-aspect ratio wing. The computational study was undertaken in support of a wind tunnel experimental program. The computational results are compared to experimental surface pressure data obtained in a cryogenic wind tunnel with an adaptive wall test section. The results show favorable agreement over a wide range of conditions, further the numerical results provide additional data of the complex three-dimensional flow field. Differences in the predictions and experiment suggest a need to conduct further experiments to evaluate the adaptive wall testing technique, and to model the tunnel sidewall boundary layer in the computations.

Milholen, William E., II↗
NASA NTRS2011

Planning Image-Based Measurements in Wind Tunnels by Virtual Imaging

Virtual imaging is routinely used at NASA Ames Research Center to plan the placement of cameras and light sources for image-based measurements in production wind tunnel tests. Virtual imaging allows users to quickly and comprehensively model a given test situation, well before the test occurs, in order to verify that all optical testing requirements will be met. It allows optimization of the placement of cameras and light sources and leads to faster set-up times, thereby decreasing tunnel occupancy costs. This paper describes how virtual imaging was used to plan optical measurements for three tests in production wind tunnels at NASA Ames.

Kushner, Laura Kathryn↗
NASA NTRS2001

DARPA/AFRL/NASA Smart Wing Second Wind Tunnel Test Results

To quantify the benefits of smart materials and structures adaptive wing technology, Northrop Grumman Corp. (NGC) built and tested two 16% scale wind tunnel models (a conventional and a "smart" model) of a fighter/attack aircraft under the DARPA/AFRL/NASA Smart Materials and Structures Development - Smart Wing Phase 1. Performance gains quantified included increased pitching moment (C(sub M)), increased rolling moment (C(subl)) and improved pressure distribution. The benefits were obtained for hingeless, contoured trailing edge control surfaces with embedded shape memory alloy (SMA) wires and spanwise wing twist effected by SMA torque tube mechanisms, compared to conventional hinged control surfaces. This paper presents an overview of the results from the second wind tunnel test performed at the NASA Langley Research Center s (LaRC) 16ft Transonic Dynamic Tunnel (TDT) in June 1998. Successful results obtained were: 1) 5 degrees of spanwise twist and 8-12% increase in rolling moment utilizing a single SMA torque tube, 2) 12 degrees of deflection, and 10% increase in rolling moment due to hingeless, contoured aileron, and 3) demonstration of optical techniques for measuring spanwise twist and deflected shape.

Scherer, L. B.↗
NASA NTRS1976

Wind tunnel investigation of a large-scale model of a lift/cruise fan V/STOL aircraft

An investigation was conducted in the Ames 40- by 80-Foot wind tunnel to determine the aerodynamic characteristics of a large scale model of a lift/cruise fan V/STOL aircraft. The model was equipped with three fans, one mounted in the forward section of the fuselage in a lift mode, and two mounted on top of the wing adjacent to the fuselage in a lift/cruise mode. The data that were obtained include longitudinal and lateral-directional characteristics of the model, with the horizontal tail on and off, for both the Powered lift and cruise configurations. Powered lift data were obtained at several wind tunnel velocities and at several lift/cruise fan thrust vector angles by varying the position of the hooded deflectors from 0 deg. (the cruise condition) to 90 deg.

Gambucci, B. J.↗
NASA NTRS1974

Wind-tunnel tests and computer simulations of buoyant wing-tip vortices

It is demonstrated that wing-tip vortices with buoyant cores can be made in a wind tunnel. Wing-tip vortices generated by an aircraft often become buoyant, because of heating effects due to the jet exhaust or in connection with a descending motion in a stable atmosphere. A description of wind-tunnel studies is given, taking into account the experimental conditions, the transition to turbulence, and the drift of the buoyant vortex. A computer simulation of wing-tip vortices is also discussed.

Costen, R. C.↗
NASA NTRS1984

Aerodynamic characteristics of the 40- by 80-/80- by 120-ft wind tunnel at NASA-Ames Research Center

The design and testing of vane sets and air-exchange inlet for the 40 x 80/80 x 120-ft wind tunnel at NASA Ames are reported. Boundary-layer analysis and 2D and 3D inviscid panel codes are employed in computer models of the system, and a 1/10-scale 2D facility and a 1/50-scale 3D model of the entire wind tunnel are used in experimental testing of the vane sets. The results are presented in graphs, photographs, drawings, and diagrams and discussed. Generally good agreement is found between the predicted and measured performance.

Corsiglia, V. R.↗
NASA NTRS1981

Some anomalies between wind tunnel and flight transition results

A review of environmental disturbance influence and boundary layer transition measurements on a large collection of reference sharp cone tests in wind tunnels and of recent transonic-supersonic cone flight results have previously demonstrated the dominance of free-stream disturbance level on the transition process from the beginning to end. Variation of the ratio of transition Reynolds number at onset-to-end with Mach number has been shown to be consistently different between flight and wind tunnels. Previous correlations of the end of transition with disturbance level give good results for flight and large number of tunnels, however, anomalies occur for similar correlation based on transition onset. Present cone results with a tunnel sonic throat reduced the disturbance level by an order of magnitude with transition values comparable to flight.

Harvey, W. D.↗
NASA NTRS1999

Unstructed Navier-Stokes Analysis of Wind-Tunnel Aeroelastic Effects on TCA Model 2

The aim of this work is to demonstrate a simple technique which accounts for aeroelastic deformations experienced by HSR wind-tunnel models within CFD computations. With improved correlations, CFD can become a more effective tool for augmenting the post-test understanding of experimental data. The present technique involves the loose coupling of a low-level structural representation within the ELAPS code, to an unstructured Navier-Stokes flow solver, USM3Dns. The ELAPS model is initially calibrated against bending characteristics of the wind-tunnel model. The strength of this method is that, with a single point calibration of a simple structural representation, the static aeroelastic effects can be accounted for in CFD calculations across a range of test conditions. No prior knowledge of the model deformation during the wind-on test is required. This approach has been successfully applied to the high aspect-ratio planforms of subsonic transports. The current challenge is to adapt the procedure to low aspect-ratio planforms typical of HSR configurations.

Frink, Neal T.↗
NASA NTRS1973

The results of a high-speed wind tunnel test to investigate the effects of the NASA refan JT8D engine nacelles on the stability and control characteristics of the Boeing 727 airplane

A high speed wind tunnel test was conducted to investigate the effects of the NASA Refan JT8D engine nacelles on the stability and control characteristics of the Boeing 727 airplane. The test was performed at the Calspan Corporation 8x8 ft. (2.44x2.44 m.) transonic wind tunnel. Both the 727-200 and -100 models were tested. A small nose-down pitching moment increment and a slight increase in longitudinal stability were noted due to the Refan nacelles. The directional stability of the 727-200 airplane increased up to 10 percent. A smaller improvement was observed on the 727-100 model. In general, the high speed stability and control characteristics of the basic airplane are not significantly altered by the Refan nacelle installation.

Kupcis, E. A.↗
NASA NTRSDate not supplied

Computational Modeling of Two Mars Powered Descent Vehicle Concepts Tested in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not suitable for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). This paper covers computational flowfield predictions completed at wind tunnel conditions and comparisons to the test data. On the blowing HIAD models, the time-averaged pressure inboard of the nozzles was generally well-predicted, especially if the nozzles are canted outward, when the nozzles are located further from the nose. At intermediate CobraMRV thrust coefficients, CFD pressures are more accurately predicted than they are for the HIAD models, largely due to the nozzle locations and pointing directions. Overall, the CFD pressure coefficients were predicted within 0.2 of the steady pressure measurements for all blowing models, with smaller discrepancies at higher HIAD thrust, and larger discrepancies at lower HIAD CobraMRV thrust. All HIAD models were predicted to have a gradually decreasing axial force coefficient as the total thrust increases, in agreement with available pressure sensitive paint data. On models with canted nozzles or with nozzles further from the nose, the force coefficient was slightly higher for a given thrust. On the CobraMRV model, the CFD also shows consistent results between solvers and follows trends revealed in the data; the aerodynamic force coefficient remains near the non-blowing value at a tunnel Mach number of 2.4 regardless of thrust, and increases above that level at a Mach number of 3.5, consistent with the discrete pressure data. CFD analysis at tunnel and flight conditions will continue as flight system designs concepts mature.

Supersonic Retropropulsion↗
NASA NTRS1996

An Experimental Device for Generating High Frequency Perturbations in Supersonic Wind Tunnels

This paper describes the analytical study of a device that has been proposed as a mechanism for generating gust-like perturbations in supersonic wind tunnels. The device is envisioned as a means to experimentally validate dynamic models and control systems designed for high-speed inlets. The proposed gust generator is composed of two flat trapezoidal plates that modify the properties of the flow ingested by the inlet. One plate may be oscillated to generate small perturbations in the flow. The other plate is held stationary to maintain a constant angle-of-attack. Using an idealized approach, design equations and performance maps for the new device were developed from the compressible flow relations. A two-dimensional CFD code was used to confirm the correctness of these results. The idealized approach was then used to design and evaluate a new gust generator for a 3.05-meter by 3.05-meter (10-foot by 10-foot) supersonic wind tunnel.

Melcher, Kevin J.↗
NASA NTRSDate not supplied

Computational Modeling of Two Mars Powered Descent Vehicle Concepts Tested in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not suitable for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). This paper covers computational flowfield predictions completed at wind tunnel conditions and comparisons to the test data. On the blowing HIAD models, the time-averaged pressure inboard of the nozzles was generally well-predicted, especially if the nozzles are canted outward, when the nozzles are located further from the nose. At intermediate CobraMRV thrust coefficients, CFD pressures are more accurately predicted than they are for the HIAD models, largely due to the nozzle locations and pointing directions. Overall, the CFD pressure coefficients were predicted within 0.2 of the steady pressure measurements for all blowing models, with smaller discrepancies at higher HIAD thrust, and larger discrepancies at lower HIAD CobraMRV thrust. All HIAD models were predicted to have a gradually decreasing axial force coefficient as the total thrust increases, in agreement with available pressure sensitive paint data. On models with canted nozzles or with nozzles further from the nose, the force coefficient was slightly higher for a given thrust. On the CobraMRV model, the CFD also shows consistent results between solvers and follows trends revealed in the data; the aerodynamic force coefficient remains near the non-blowing value at a tunnel Mach number of 2.4 regardless of thrust, and increases above that level at a Mach number of 3.5, consistent with the discrete pressure data. CFD analysis at tunnel and flight conditions will continue as flight system designs concepts mature.

Supersonic Retropropulsion↗
NASA NTRS2014

11-by 11-Foot Transonic Leg of the Unitary Plan Wind Tunnel (UPWT) CAD Model

A ProEngineer CAD model of the 11 Unitary Plan wind tunnel test section, diffuser inlet, plenum chamber, strut and aft diffuser has been created for use with analysis tools such as Cart3D and Star CCM+. Separate parts of the tunnel are created as parts files and assembled in an assembly file. Two merged solid parts are used for meshing. This report describes each of the parts files and features of the merged models.

computational analysis↗