Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transportation System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Orbiter S-band direct link system verification test report

Space-to-ground S-band communications system compatibility and performance tests were performed for the various radio frequency links. These tests consisted of the various uplink and downlink signal combinations (data rates) for the phase modulation system and both realtime and playback data rates for the frequency modulated downlink systems. In addition, tests involving encryption/decryption, Doppler, and acquisition were performed. Results show that the S-band transponder for the space shuttle orbiter is compatible with the S-band equipment of the AFSCF/RTS (Air Force Satellite Control Facility/Remote Tracking Station). It is also concluded that the performance of the orbiter-AFSCF/RTS direct link exceeds the required performance and that this communications link will meet the system requirements of the Space Transportation System.

Vermillion, B. K.↗

STS-1 environmental control and life support system. Consumables and thermal analysis

The Environmental Control and Life Support Systems (ECLSS)/thermal systems analysis for the Space Transportation System 1 Flight (STS-1) was performed using the shuttle environmental consumables usage requirements evaluation (SECURE) computer program. This program employs a nodal technique utilizing the Fortran Environmental Analysis Routines (FEAR). The output parameters evaluated were consumable quantities, fluid temperatures, heat transfer and rejection, and cabin atmospheric pressure. Analysis of these indicated that adequate margins exist for the nonpropulsive consumables and related thermal environment.

Steines, G.↗

Advanced Earth-to-orbit propulsion technology program overview: Impact of civil space technology initiative

The NASA Earth-to-Orbit (ETO) Propulsion Technology Program is dedicated to advancing rocket engine technologies for the development of fully reusable engine systems that will enable space transportation systems to achieve low cost, routine access to space. The program addresses technology advancements in the areas of engine life extension/prediction, performance enhancements, reduced ground operations costs, and in-flight fault tolerant engine operations. The primary objective is to acquire increased knowledge and understanding of rocket engine chemical and physical processes in order to evolve more realistic analytical simulations of engine internal environments, to derive more accurate predictions of steady and unsteady loads, and using improved structural analyses, to more accurately predict component life and performance, and finally to identify and verify more durable advanced design concepts. In addition, efforts were focused on engine diagnostic needs and advances that would allow integrated health monitoring systems to be developed for enhanced maintainability, automated servicing, inspection, and checkout, and ultimately, in-flight fault tolerant engine operations.

Stephenson, Frank W., Jr.↗

Electric propulsion for lunar exploration and lunar base development

Using electric propulsion to deliver materials to lunar orbit for the development and construction of a lunar base was investigated. Because the mass of the base and its life-cycle resupply mass are large, high specific impulse propulsion systems may significantly reduce the transportation system mass and cost. Three electric propulsion technologies (arcjet, ion, and magnetoplasmadynamic (MPD) propulsion) were compared with oxygen/hydrogen propulsion for a lunar base development scenario. Detailed estimates of the orbital transfer vehicles' (OTV's) masses and their propellant masses are presented. The fleet sizes for the chemical and electric propulsion systems are estimated. Ion and MPD propulsion systems enable significant launch mass savings over O2/H2 propulsion. Because of the longer trip time required for the low-thrust OTV's, more of them are required to perform the mission model. By offloading the lunar cargo from the manned O2/H2 OTV missions onto the electric propulsion OTV's, a significant reduction of the low Earth orbit (LEO) launch mass is possible over the 19-year base development period.

Palaszewski, Bryan↗

CONFIG: Integrated engineering of systems and their operation

This article discusses CONFIG 3, a prototype software tool that supports integrated conceptual design evaluation from early in the product life cycle, by supporting isolated or integrated modeling, simulation, and analysis of the function, structure, behavior, failures and operations of system designs. Integration and reuse of models is supported in an object-oriented environment providing capabilities for graph analysis and discrete event simulation. CONFIG supports integration among diverse modeling approaches (component view, configuration or flow path view, and procedure view) and diverse simulation and analysis approaches. CONFIG is designed to support integrated engineering in diverse design domains, including mechanical and electro-mechanical systems, distributed computer systems, and chemical processing and transport systems.

Malin, Jane T.↗

Computer-aided operations engineering with integrated models of systems and operations

CONFIG 3 is a prototype software tool that supports integrated conceptual design evaluation from early in the product life cycle, by supporting isolated or integrated modeling, simulation, and analysis of the function, structure, behavior, failures and operation of system designs. Integration and reuse of models is supported in an object-oriented environment providing capabilities for graph analysis and discrete event simulation. Integration is supported among diverse modeling approaches (component view, configuration or flow path view, and procedure view) and diverse simulation and analysis approaches. Support is provided for integrated engineering in diverse design domains, including mechanical and electro-mechanical systems, distributed computer systems, and chemical processing and transport systems. CONFIG supports abstracted qualitative and symbolic modeling, for early conceptual design. System models are component structure models with operating modes, with embedded time-related behavior models. CONFIG supports failure modeling and modeling of state or configuration changes that result in dynamic changes in dependencies among components. Operations and procedure models are activity structure models that interact with system models. CONFIG is designed to support evaluation of system operability, diagnosability and fault tolerance, and analysis of the development of system effects of problems over time, including faults, failures, and procedural or environmental difficulties.

Malin, Jane T.↗

Peroxide Propulsion at the Turn of the Century

A resurgence of interest in peroxide propulsion has occurred in the last years of the 21st Century. This interest is driven by the need for lower cost propulsion systems and the need for storable reusable propulsion systems to meet future space transportation system architectures. NASA and the Air Force are jointly developing two propulsion systems for flight demonstration early in the 21st Century. One system will be a development of Boeing's AR2-3 engine, which was successfully fielded in the 1960s. The other is a new pressure-fed design by Orbital Sciences Corporation for expendable mission requirements. Concurrently NASA and industry are pursuing the key peroxide technologies needed to design, fabricate, and test advanced peroxide engines to meet the mission needs beyond 2005. This paper will present a description of the AR2-3, report the status of its current test program, and describe its intended flight demonstration. This paper will then describe the Orbital 10K engine, the status of its test program, and describe its planned flight demonstration. Finally the paper will present a plan, or technology roadmap, for the development of an advanced peroxide engine for the 21st Century.

Anderson, William E.↗

Towards Flange-to-Flange Turbopump Simulations for Liquid Rocket Engines

The primary objective of this research is to support the design of liquid rocket systems for the Advanced Space Transportation System. Since the space launch systems in the near future are likely to rely on liquid rocket engines, increasing the efficiency and reliability of the engine components is an important task. One of the major problems in the liquid rocket engine is to understand fluid dynamics of fuel and oxidizer flows from the fuel tank to plume. Understanding the flow through the entire turbopump geometry through numerical simulation will be of significant value toward design. This will help to improve safety of future space missions. One of the milestones of this effort is to develop, apply and demonstrate the capability and accuracy of 3D CFD methods as efficient design analysis tools on high performance computer platforms. The development of the MPI and MLP versions of the INS3D code is currently underway. The serial version of INS3D code is a multidimensional incompressible Navier-Stokes solver based on overset grid technology. INS3D-MPI is based on the explicit massage-passing interface across processors and is primarily suited for distributed memory systems. INS3D-MLP is based on multi-level parallel method and is suitable for distributed-shared memory systems. For the entire turbopump simulations, moving boundary capability and an efficient time-accurate integration methods are build in the flow solver. To handle the geometric complexity and moving boundary problems, overset grid scheme is incorporated with the solver that new connectivity data will be obtained at each time step. The Chimera overlapped grid scheme allows subdomains move relative to each other, and provides a great flexibility when the boundary movement creates large displacements. The performance of the two time integration schemes for time-accurate computations is investigated. For an unsteady flow which requires small physical time step, the pressure projection method was found to be computationally efficient since it does not require any subiterations procedure. It was observed that the artificial compressibility method requires a fast convergence scheme at each physical time step in order to satisfy incompressibility condition. This was obtained by using a GMRES-ILU(0) solver in our computations. When a line-relaxation scheme was used, the time accuracy was degraded and time-accurate computations became very expensive. The current geometry for the LOX boost turbopump has various rotating and stationary components, such as inducer, stators, kicker, hydrolic turbine, where the flow is extremely unsteady. Figure 1 shows the geometry and computed surface pressure of the inducer. The inducer and the hydrolic turbine rotate in different rotational speed.

Kiris, Cetin↗

Supercomputing Aspects for Simulating Incompressible Flow

The primary objective of this research is to support the design of liquid rocket systems for the Advanced Space Transportation System. Since the space launch systems in the near future are likely to rely on liquid rocket engines, increasing the efficiency and reliability of the engine components is an important task. One of the major problems in the liquid rocket engine is to understand fluid dynamics of fuel and oxidizer flows from the fuel tank to plume. Understanding the flow through the entire turbo-pump geometry through numerical simulation will be of significant value toward design. One of the milestones of this effort is to develop, apply and demonstrate the capability and accuracy of 3D CFD methods as efficient design analysis tools on high performance computer platforms. The development of the Message Passage Interface (MPI) and Multi Level Parallel (MLP) versions of the INS3D code is currently underway. The serial version of INS3D code is a multidimensional incompressible Navier-Stokes solver based on overset grid technology, INS3D-MPI is based on the explicit massage-passing interface across processors and is primarily suited for distributed memory systems. INS3D-MLP is based on multi-level parallel method and is suitable for distributed-shared memory systems. For the entire turbo-pump simulations, moving boundary capability and efficient time-accurate integration methods are built in the flow solver, To handle the geometric complexity and moving boundary problems, an overset grid scheme is incorporated with the solver so that new connectivity data will be obtained at each time step. The Chimera overlapped grid scheme allows subdomains move relative to each other, and provides a great flexibility when the boundary movement creates large displacements. Two numerical procedures, one based on artificial compressibility method and the other pressure projection method, are outlined for obtaining time-accurate solutions of the incompressible Navier-Stokes equations. The performance of the two methods is compared by obtaining unsteady solutions for the evolution of twin vortices behind a flat plate. Calculated results are compared with experimental and other numerical results. For an unsteady flow, which requires small physical time step, the pressure projection method was found to be computationally efficient since it does not require any subiteration procedure. It was observed that the artificial compressibility method requires a fast convergence scheme at each physical time step in order to satisfy the incompressibility condition. This was obtained by using a GMRES-ILU(0) solver in present computations. When a line-relaxation scheme was used, the time accuracy was degraded and time-accurate computations became very expensive.

Kwak, Dochan↗

Development of a tape transport bacterial detection system

The feasibility of a tape transport chemiluminescence system for bacterial monitoring of regenerated water was demonstrated using a manually operated laboratory breadboard. The principle of detection is based on measuring the increase in chemiluminescence produced by the catalytic action of bacterial porphyrins on a luminol-hydrogen peroxide mixture. Viable organisms are distinguished from nonviable by comparing the signals of incubated and unincubated water samples. Using optimized protocols, sensitivities were obtained with 400 ml suspensions of E. coli and Cl. sporogenes. The sensitivity of the unincubated cycle E. coli (aerobe) was found to be 30 to 35 cells/m1, and that of the Cl. sporogenes (anaerobe) was 1000 to 10,000 cells/m1. The lower sensitivity toward Cl. sporogenes is attributed to several factors, namely the lower cytochrome content, the tendency to sporulate, long lag periods and the lower growth rate of Clostridia in general. The operational procedures used for processing the incubated and unincubated samples involved the following sequence: (1) concentrating the sample by filtration through a membrane filter, (2) washing with Dextrose-Thioglycollate Broth (3) incubating (0 to 4 hrs as required), (4) washing with 4M Urea, and (5) reacting with reagent in front of a photomultiplier tube. The signal output was recorded on a strip chart recorder.

Witz, S.↗

Blueprinting Electrified Transit System Implementation

To achieve a more affordable and reliable transportation system, we need to smartly upgrade our power systems and install a large number of charging stations, but conventional planning methods are not up to the task. By applying advanced simulation and optimization tools, we can design a smarter, more cost-effective electric transportation network. The initial focus was on public transit systems, demonstrating how this approach can deliver broader economic, reliability, and air quality benefits nationwide.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Upper stages using liquid propulsion and metallized propellants

Metallized propellants are liquid propellants with a metal additive suspended in a gelled fuel. Typically, aluminum particles are the metal additive. These propellants increase the density and/or the specific impulse of the propulsion system. Using metallized propellants for volume- and mass-constrained upper stages can deliver modest increases in performance for low Earth orbit to geosynchronous Earth orbit (LEO-GEO) and other Earth-orbital transfer missions. However, using metallized propellants for planetary missions can deliver great reductions in flight time with a single-stage, upper-stage system. Tradeoff studies comparing metallized propellant stage performance with nonmetallized upper stages and the Inertial Upper Stage (IUS) are presented. These upper stages, launched from the STS and STS-C, are both one- and two-stage vehicles that provide the added energy to send payloads to high altitude orbits and onto interplanetary trajectories that are unattainable with only the Space Transportation System (STS) and the Space Transportation System-Cargo (STS-C). The stage designs are controlled by the volume and the mass constraints of the STS and STS-C launch vehicles. The influences of the density and specific impulse increases enabled by metallized propellants are examined for a variety of different stage and propellant combinations.

Palaszewski, Bryan A.↗

The smart highway project: Smart highways, smart vehicles, smart engineering

The Smart Highway project is a six mile, limited access roadway being built between Interstate 81 and Blacksburg, Virginia. The initial construction segment will be two miles long and is designed to serve as a test bed and test track for Intelligent Transportation Systems (ITS) research. The Center for Transportation Research (CTR) at Virginia Tech is developing three evaluation tools for its ITS research including DYNAVIMTS (a software framework), and the FLASH Lab (a 1/15th scale model highway and vehicle system). The Smart Highway rounds out the Center's evaluation methodology by allowing full scale operational tests, evaluations, and research under both experimental and conventional traffic conditions. Currently under development is a concept for a fully automated highway using a 'Cooperative Infrastructure Managed System' which involves ultra wide band communication beacons installed in the infrastructure with appropriate sensors, receivers and processors on board the vehicles. The project is part of the research program funded by the National Automated Highway System Consortium. The CTR hopes to develop the automated concept to prototype status by 1997. Other smart transportation and smart engineering concepts are proposed. This presentation will address the goals and objectives of the Smart Highway project, overview its status and importance to the region, and identify some of the transportation technology now under development and planned in the future.

Pethtel, Ray D.↗

Energy and mobility impacts of connected autonomous vehicles with co-optimization of speed and powertrain on mixed vehicle platoons

Intersections are known to be traffic bottlenecks where a significant amount of energy consumption could be caused due to deceleration/acceleration in the presence of red signals. With an increased level of connectivity and automation of intelligent transportation systems, connected autonomous vehicles (CAVs) are expected to be able to proactively adjust their driving strategies subject to constraints imposed by the predicted future traffic. As a result, many potential benefits can be achieved, such as improved energy efficiency, enhanced traffic safety, among many others. Notably, the way CAVs are controlled affects the following legacy vehicles (LVs) due to complex traffic dynamics. Here, we are particularly interested in studying the energy and mobility impact of CAVs with an improved traffic prediction method on mixed vehicle platoons at various market penetration rates. Leveraging traffic prediction, CAVs are controlled with co-optimization of their speed and gear position. Specifically, a traffic prediction framework in a rolling horizon fashion is employed based upon a modified Payne–Whitham (PW) model capable of handling mixed traffic consisting of CAVs and LVs. The prediction error of the modified PW model is reduced by 53.62% compared to that of the standard PW model under test scenarios. According to the predicted traffic conditions, speed and gear position of CAVs are co-optimized with the primary goal of minimizing energy consumption when driving on a signalized arterial. The energy benefits achieved by CAVs and the impact of CAVs on LVs behind are studied comprehensively for mixed vehicle platoons. The lead LV follows a real-world speed profile collected on TH-55 in Minnesota. Numerical results show that energy benefits achieved by the vehicle platoon range from 2% to 16%, and a 1% to 5% reduction in travel time for LVs behind CAVs is also observed, at different penetration rates of CAVs in various traffic scenarios. Furthermore, it is observed that CAVs using the proposed eco-driving approach appear to have a positive impact on the LVs behind in terms of energy consumption, regardless of the driving styles of the LVs ahead.

33 ADVANCED PROPULSION SYSTEMS↗

Issue focused stakeholder collaboration: reaching consensus on spent nuclear fuel transportation operational practices - 15465

This paper examines stakeholder and issue-focused approaches used by Department of Energy (DOE) programs to collaborate with key stakeholders on transportation practices to ship radioactive material, particularly used nuclear fuel (UNF) and transuranic waste (TRU). In accordance with the Administration's Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste, the current effort by DOE to plan for the development of a future transportation system to ship UNF from commercial reactors, with an initial focus on shutdown reactors, is using approaches similar to those used in other successful shipping campaigns to collaborate with stakeholders about sustainable transportation practices. As part of a coordinated approach to stakeholder outreach and collaboration, DOE is currently developing a draft Transportation Planning Framework to provide a template for future shipments of UNF from commercial reactors and is engaged with states and tribes and other stakeholders in discussions on the institutional and operational components of that Framework. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Developmental Flight Instrumentation: Review of Space Shuttle, Ares I-X, and Artemis I

Ascent vehicles in the developmental stages of the program are instrumented with Developmental Flight Instrumentation (DFI) sensors. These sensors establish a link between a vehicle and engineers on the ground to communicate conditions experienced during the ascent. These data are then compared to pre-flight predictions used in the design process. The aerodynamic, acoustic, thermal, and structural data are either telemetered to ground stations during the ascent or stored on the vehicle for post-flight recovery and archived at the Huntsville Operations Support Center (HOSC). Following NASA's Artemis I Space Launch System (SLS) launch on November 16, 2020, data from three separate programs are available at the HOSC: Space Shuttle Program (Space Transport System (STS)), Constellation Program (Ares I-X), and Artemis Program (SLS). Availability of these data presents a unique opportunity to examine DFI data from three distinct vehicles and analyze the broad impact of the DFI data on the understanding of transonic aerodynamics. Classical spectrogram and Empirical Mode Decomposition techniques were used to present data in aerodynamically analogous regions on each vehicle. On the SLS and Ares I-X, a region downstream of the Launch Abort System motors was chosen. Comparing SLS and the STS, a region downstream of booster Froward Attach Hardware was selected as analogous flow region. Some other regions of interest were also identified. Although similarities in flow features on three vehicles were identified, some challenges in the comparison were also encountered, especially due to poor temporal and spatial resolution of Shuttle measurements.

Space Shuttle↗

Developmental Flight Instrumentation: Review of Space Shuttle, Ares I-X, and Artemis I

Ascent vehicles in the developmental stages of the program are instrumented with Developmental Flight Instrumentation (DFI) sensors. These sensors establish a link between a vehicle and engineers on the ground to communicate conditions experienced during the ascent. These data are then compared to pre-flight predictions used in the design process. The aerodynamic, acoustic, thermal, and structural data are either telemetered to ground stations during the ascent or stored on the vehicle for post-flight recovery and archived at the Huntsville Operations Support Center (HOSC). Following NASA's Artemis I Space Launch System (SLS) launch on November 16, 2020, data from three separate programs are available at the HOSC: Space Shuttle Program (Space Transport System (STS)), Constellation Program (Ares I-X), and Artemis Program (SLS). Availability of these data presents a unique opportunity to examine DFI data from three distinct vehicles and analyze the broad impact of the DFI data on the understanding of transonic aerodynamics. Classical spectrogram and Empirical Mode Decomposition techniques were used to present data in aerodynamically analogous regions on each vehicle. On the SLS and Ares I-X, a region downstream of the Launch Abort System motors was chosen. Comparing SLS and the STS, a region downstream of booster Froward Attach Hardware was selected as analogous flow region. Some other regions of interest were also identified. Although similarities in flow features on three vehicles were identified, some challenges in the comparison were also encountered, especially due to poor temporal and spatial resolution of Shuttle measurements.

Space Shuttle↗