Temperature effects on irradiated solar cells
Temperature effects on irradiated solar cells
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Temperature effects on irradiated solar cells
The SnS absorber layer in solar cell devices was produced by vapor transport deposition (VTD), which is a low-cost manufacturing method for solar modules. The performance of solar cells consisting of Si/Mo/SnS/ZnO/indium tin oxide (ITO) was limited by the SnS layer's surface texture and field-dependent carrier collection. For improved performance, a fluorine doped tin oxide (FTO) substrate was used in place of the Mo to smooth the topography of the VTD SnS and to make bifacial solar cells, which are potentially useful for multijunction applications. A bifacial SnS solar cell consisting of glass/FTO/SnS/CdS/ZnO/ITO demonstrated front- and back-side power conversion efficiencies of 1.2% and 0.2%, respectively.
Although GaAs solar cells are radiation-resistant and have high conversion efficiencies, there are two major obstacles that such cells must overcome before they can be widely adopted for space applications: GaAs wafers are too expensive and cells made from these wafers are too heavy. The CLEFT process permits the growth of thin single-crystal films on reusable substrates, resulting in a drastic reduction in both cell cost and cell weight. Recent advances in CLEFT technology have made it possible to achieve efficiencies of about 14 percent AM0 for 0.51-sq cm GaAs solar cells 5 microns thick with a 41-mil-thick coverglass. In preliminary experiments efficiencies close to 19 percent AM1 have been obtained for 10-micron-thick cells. It is suggested that the CLEFT technology should yield inexpensive, highly efficient modules with a beginning-of-life specific power close to 1 kW/kg (for a coverglass thickness of 4 mils).
Many of the demands of high-throughput processing of solar cells can be satisfied by transient methods using pulsed electron beams. A prototype pulsed electron beam processor for solar cell production has been built, and is intended for automated annealing of solar cell junction ion implantation at a rate of 1200-1800 silicon wafers per hour. Other applications include solar cell junctions by pulse diffusion, annealing of ion-implanted back surface fields, and pulse sintering of cell metallization.
Spectral response measurement plays great role in characterizing solar cell device because it directly reflects the efficiency by which the device converts the sunlight into an electrical current. Based on the spectral response results, the short circuit current of each subcell can be quantitatively determined. Although spectral response dependence on wavelength, i.e., the well-known external quantum efficiency (EQE), has been widely used in characterizing multijunction solar cell and has been well interpreted, detailed analysis of spectral response dependence on bias voltage (SR −V{sub bias}) has not been reported so far. In this work, we have performed experimental and numerical studies on the SR −V{sub bias} for Ga{sub 0.51}In{sub 0.49}P/Ga{sub 0.99}In{sub 0.01}As/Ge triple junction solar cell. Phenomenological description was given to clarify the mechanism of operation matching point variation in SR −V{sub bias} measurements. The profile of SR−V{sub bias} curve was explained in detail by solving the coupled two-diode current-voltage characteristic transcend formula for each subcell.
Computer-controlled ink-jet-assisted metallization of the front surface of solar cells with metalorganic silver inks offers a maskless alternative method to conventional photolithography and screen printing. This method can provide low cost, fine resolution, reduced process complexity, avoidance of degradation of the p-n junction by firing at lower temperature, and uniform line film on rough surface of solar cells. The metallization process involves belt furnace firing and thermal spiking. With multilayer ink jet printing and firing, solar cells of about 5-6 percent efficiency without antireflection (AR) coating can be produced. With a titanium thin-film underlayer as an adhesion promoter, solar cells of average efficiency 8.08 percent without AR coating can be obtained. This efficiency value is approximately equal to that of thin-film solar cells of the same lot. Problems with regard to lower inorganic content of the inks and contact resistance are noted.
Highlights: • Ag{sub 2}S QD is a good photovoltaic material suit for fabricating QDSSCs. • Solvothermal method, precursor thermal decomposition method are two suitable proccesses for synthesizing Ag{sub 2}S QDs. • The higher PCE will be realized for Ag{sub 2}S QDSSCs through ameliorating structures of solar cell. - Abstract: Ag{sub 2}S quantum dot is a semiconductor with narrow band-gap, high chemical stability, broad light absorption, photovoltaic effect and photoluminescence, which makes it a good photovoltaic material for fabricating solar cells. Many works have been conducted to demonstrate the synthesis of Ag{sub 2}S nanostructure, as well as their applications in solar cells. In this article, the recent development of methods for synthesizing Ag{sub 2}S quantum dots and Ag{sub 2}S-based solar cells is reviewed. Especially metal oxide/Ag{sub 2}S-based solar cells, Ag{sub 2}S quantum dots, dye co-sensitized solar cells and inorganic-organic hybrid solar cells have been detailed. Ag{sub 2}S quantum dots, with broad light absorption band and extensive absorption coefficient, have shown large potential in fabricating quantum dot-sensitized solar cells as well as polymer solar cells.
The performance of polymer:fullerene bulk heterojunction (BHJ) solar cells is significantly influenced by the morphology of electron donor and acceptor blends under the premise that electronic structure is complimentary regarding donor and acceptor materials. There are many cases where intimate mixing of donor and acceptor perturbs the electronic structure, which fundamentally changes the transport and photovoltaic characteristics. In this work, we present the bimolecular crystal packing of polymers and fullerenes, and investigate the correlation between device performance and structural details. We find that bimolecular crystallization can reorganize polymer chain packing, leading to poor electron transport and device performance. The size compatibility and the passivation of entropy penalty led to cocrystallization instability, which was clearly seen by in situ GIWAXS data. PC 61 BM is found to intercalate into side chains of PQT by reorganizing both PQT and PC 61 BM, forming stable, highly ordered bimolecular crystals. The poor electron transport in bimolecular crystal domain could account for the poor device performance in both perovskite and organic solar cells. Bis-PC 61 BM, on the other hand, only forms loosely packed aggregates in solution, and then rapidly phase separated into large domains with an edge-on interfacial orientation and performed poorly in solar cells.
"Very efficient crystalline silicon (c-Si) solar cells have been demonstrated when thin layers of intrinsic and doped hydrogenated amorphous silicon (a-Si:H) are used for passivation and carrier selectivity in a heterojunction device. One limitation of this device structure is the (parasitic) absorption in the front passivation/collection a-Si:H layers; another is the degradation of the a-Si:H-based passivation upon temperature, limiting the post-processes to approximately 200°C thus restricting the contacting possibilities and potential tandem device fabrication. To alleviate these two limitations, we explore the potential of amorphous silicon carbide (a-SiC:H), a widely studied material in use in standard a-Si:H thin-film solar cells, which is known for its wider bandgap, increased hydrogen content and stronger hydrogen bonding compared to a-Si:H. We study the surface passivation of solar-grade textured n-type c-Si wafers for symmetrical stacks of 10-nm-thick intrinsic a-SiC:H with various carbon content followed by either p-doped or n-doped a-Si:H (referred to as i/p or i/n stacks). For both doping types, passivation (assessed through carrier lifetime measurements) is degraded by increasing the carbon content in the intrinsic a-SiC:H layer. Yet, this hierarchy is reversed after annealing at 350°C or more due to drastic passivation improvements upon annealing when an a-SiC:H layer is used. After annealing at 350°C, lifetimes of 0.4 ms and 2.0 ms are reported for i/p and i/n stacks, respectively, when using an intrinsic a-SiC:H layer with approximately 10% of carbon (initial lifetimes of 0.3 ms and 0.1 ms, respectively, corresponding to a 30% and 20-fold increase, respectively). For stacks of pure a-Si:H material the lifetimes degrade from 1.2 ms and 2.0 ms for i/p and i/n stacks, respectively, to less than 0.1 ms and 1.1 ms (12-fold and 2-fold decrease, respectively). For complete solar cells using pure a-Si:H i/p and i/n stacks, the open-circuit voltage (Voc) drops from 720 mV to 600 mV when annealing the device at 350°C. Yet, the Voc of devices using an intrinsic a-SiC:H layer with around 10% carbon content in the i/p stack is more resilient to such process, dropping from 710 mV to 690 mV. Also, irrespective of annealing, the slightly improved transparency of a-SiC:H layers allows about 1% current gain due to a better blue-light response. Active-area efficiencies above 20% are thus obtained for particular carbon content conditions, slightly higher than for devices using only a-Si:H. Even for a-SiC:H layers with bandgaps of up to 2.1 eV, good hole collection is maintained (with fill factors of 67% for devices using intrinsic a-SiC:H in the i/p stack, compared to 73% for the reference device). However, S-shaped current-voltage curves were obtained for devices using such a-SiC:H layers in the i/n stack, indicating impeded transport, which would suggest that most of the bandgap increase translates in a conduction-band offset.
This paper discusses the performance limitations of silicon solar cells which have been identified and investigated using a detailed numerical analysis of solar cell operation. Efficiency limitations are discussed as related to doping densities, minority carrier lifetimes, widths of solar cell regions, surface recombination, antireflecting layers, and ohmic contact stripes. Areas in which improvements can be expected in performance are identified and discussed.
III-V materials have achieved the highest efficiency of any solar cell technology. They have been commercially available since the 1960s, and have been widely used in space applications where high performance is required. However, prices of III-V solar cells are currently 2 to 3 orders of magnitude higher than other technologies, prohibiting their use in mainstream photovoltaic (PV) markets outside of high concentration photovoltaic systems. In this report, we present bottom-up cost models for current III-V solar cell technology, and explore the reasons behind these high costs. Then, we examine the advances required to drive cost down, and present a roadmap illustrating potential pathways to reach costs that could enable III-Vs to be competitive in broader, terrestrial markets without concentration. We find that cell manufacturing costs of $0.40/W or below could be achieved in high volume production, but that this would require commercialization and scale-up of a low-cost epitaxial growth technique, implementation of alternative, low-cost metallization schemes, and, critically, significant research and development to address the high cost of the substrate.
Tandem or multijunction solar cells are able to convert sunlight to electricity with greater efficiency than single junction solar cells by splitting the solar spectrum across sub-cells with different bandgaps. With the efficiencies of many common single-junction solar cell materials leveling off near their theoretical efficiency limits, there is renewed interest in applying this approach. However, there is ongoing debate as to the best approach for interconnecting sub-cells in series, or whether it is preferable to operate them independently. Here in this paper, we provide the first experimental demonstration of a tandem cell architecture with three terminals: one on top of the tandem cell, and two beneath it, in interdigitated back contact configuration. The two cells are interconnected with a transparent conductive adhesive, which is compatible with rough surfaces and exhibits negligible series resistance. Combining GaInP and Si sub-cells in this manner allows us to achieve a GaInP/Si tandem cell with a two-terminal efficiency of 26.4 ± 1.0%. We then show that utilizing all three terminals results in an efficiency boost of 0.9 ± 0.2%, to an efficiency of 27.3 ± 1.0%, and discuss the operation of the cell and its two interacting circuits.
NREL will develop a method of growing and fabricating single junction InP solar cells on 2-inch InP substrates on which a release layer has been deposited by MicroLink Devices. NREL will transfer to MicroLink the details of the InP solar cell layer structure and test results in order that the 2-inch results can be replicated on 4-inch InP substrates. NREL will develop a method of growing andfabricating single junction InP solar cells, including a metamorphic layer, on 2-inch GaAs substrates on which a release layer has been deposited by MicroLink Devices. NREL will transfer to MicroLink the details of the InP solar cell layer structure and test results in order that the 2-inch results can be replicated on 6-inch GaAs substrates. NREL will perform characterization measurements ofthe solar cells, including I-V and quantum efficiency measurements at AM1.5 1-sun.
The basic approaches to solar cell performance and diagnostic measurements are described. The light sources, equipment for I-V curve measurement, and the test conditions and procedures for performance measurement are detailed. Solar cell diagnostic tools discussed include analysis of I-V curves, series resistance and reverse saturation current determination, spectral response/quantum yield measurement, and diffusion length/lifetime determination.
The first long-term (3000 hours) UV testing of unirradiated and 1 MeV electron-irradiated GaAs solar cells, with multilayer-coated coverslides to reduce solar array operating temperature, has produced some unexpected and important results. Two results, independent of the coverslide coatings, are of particular importance in terms of the predictability of GaAs solar-array lifetime in space: ( 1) The GaAs/Ge solar cells used for this series of tests displayed a much higher radiation degradation than that predicted based on JPL Solar Cell Radiation Handbook data. Covered cells degraded more in Isc than did bare cells. Short-term illumination at 60 C did not produce significant recovery (-1%) of the radiation damage. (2) However, electron radiation damage to these GaAs solar celIs anneals at 40 C when exposed to approximately 1 sun AM0 UV light sources for extended periods. The effect appears to be roughly linear with time (-1% of lsc per 1000 UVSH), is large (greater than or equal to 3%), and has not yet saturated (at 3000 hours). This photo-recovery of radiation damage to GaAs solar cells is a new effect and potentially important to the spacecraft community. The figure compares the effects of extended UV on irradiated and unirradiated GaAs solar cells with INTELSAT-6 Si cells. The effect and its generality, the extent of and conditions for photo-recovery, and the implications of such recovery for missions in radiation environments have not yet been determined.
AlGaInP solar cells with bandgaps between 1.9 and 2.2 eV are investigated for use in next-generation multijunction photovoltaic devices. This quaternary alloy is of great importance to the development of III-V solar cells with five or more junctions and for cells optimized for operation at elevated temperatures because of the high bandgaps required in these designs. In this work, we explore the conditions for the organometallic vapor-phase epitaxy growth of AlGaInP and study their effects on cell performance. Initial efforts focused on developing ~2.0-eV AlGaInP solar cells with a nominal aluminum composition of 12%. Under the direct spectrum at 1000 W/m 2 (AM1.5D), the best of these samples had an open-circuit voltage of 1.59 V, a bandgap-voltage offset of 440 mV, a fill factor of 88.0%, and an efficiency of 14.8%. We then varied the aluminum composition of the alloy from 0% to 24% and were able to tune the bandgap of the AlGaInP layers from ~1.9 to ~2.2 eV. Furthermore, while the samples with a higher aluminum composition exhibited a reduced quantum efficiency and increased bandgap-voltage offset, the bandgap-voltage offset remained at 500 mV or less, up to a bandgap of ~2.1 eV.
Modified procedure for testing solar photovoltaic cells and modified software for processing test data provide corrections for effects of cell capacitance. Procedure and software needed because (a) some photovoltaic devices (for example, silicon solar cells with back-surface field region) store minority charge carriers in cell junction and thus exhibit significant capacitance, (b) capacitance affects current-vs.-voltage (I-V) measurements made when transient load connected to cell, and (c) transient load used in unmodified version of test procedure. Corrected I-V curve obtained in test of solar cell according to modified procedure approximates true cell voltage vs. cell current more closely.
The introduction of Se in CdTe solar-cell absorbers has led to multiple beneficial effects in the devices, including an increased short-circuit current and an extended charge-carrier lifetime. A critical manufacturing step of CdSexTe1-x solar cells is CdCl2 annealing at high temperatures, during which Se diffuses through the absorber layer. Understanding the local Se distribution in the absorber and its impact on optical properties of the material is key for the further development of this thin-film solar cell technology. In a multimodal x-ray scanning microscopy approach, we investigated the impact of the annealing temperature of CdSexTe1-x solar cells on the Se distribution and on optical characteristics of the material. For this purpose, we exploited an upgraded x-ray excited optical luminescence (XEOL) detection unit that enables simultaneous spectrally and temporally resolved XEOL mapping at synchrotron facilities that are ideal for studying thin-film solar-cell materials with hard x-rays featuring high penetration depth and lateral resolution.