Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Sim”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Fabrication of Ultra-Shallow Junctions on 300 mm Wafers Using the Plasma Immersion Implanter PULSION registered Followed by Spike Annealing Using LEVITOR Furnace

Thanks to the European Project SEA-NET, an industrial version of the IBS Plasma Ion Implantation tool has been installed in LETI for the fabrication of Ultra-Shallow Junction for 45 and 32 nm CMOS on 200 and 300 mm wafers. In this study, we present first doping results on 300 mm wafers using BF{sub 3} plasma. Annealing after PULSION implantation is performed by the ASM furnace LEVITOR. This tool, which works on conduction heating is emissivity independent for temperature control and allows reaching high ramp up and ramp down speeds (up to 900 deg. C/s). Main characteristics of as implanted wafers are presented (metal contamination 2E10/cm{sup 2}, SIMS depth profiles down to 5 nm). Then the effect of convection gas in the annealing process on sheet resistance, junction depth and uniformity is presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Boron Profile Sharpening in Ultra-Shallow p{sup +}-n Junction Produced by Plasma Immersion Ion Implantation from BF{sub 3} Plasma

We have investigated plasma immersion ion implantation (PI{sup 3}) of boron with energies of 500 eV (doses up to 2x10{sup 15} cm{sup -2}) from BF{sub 3} plasma with He pre-amorphizing implantation (PAI)(energy 3 keV, dose 5x10{sup 16} cm{sup -2}). Implanted samples were subjected to RTA (T = 900 to 1050 deg. C, t = 2 to 24 sec and spike anneal). SIMS analysis of boron profiles revealed its anomalous behavior. For short RTA times the profile tail (below 5x10{sup 19} cm{sup -3}) moves toward the surface and then, as in the usual diffusion, toward the bulk at longer annealing times.

36 MATERIALS SCIENCE↗

SIMS/ARXPS - A New Technique of Retained Dopant Dose and Profile Measurement of Low Energy Doping Processes

A newly-developed surface analysis technique, which combines Secondary Ion Mass Spectrometry (SIMS) with Angle-Resolved X-ray Photoelectron Spectroscopy (ARXPS), was used to achieve more accurate results of the retained impurity doses and profiles for ultra-low energy implants, including conventional beam-line implant and plasma immersion ion implantation (PIII). Using this method, it has been found that the B{sub 2}H{sub 6}(Diborane) PIII demonstrates thicker native oxide and much more B dose loss during RTP and surface clean treatments than conventional beam-line ion implantation, due to the higher surface B concentration. In order to match the electrical parameters of the device, PIII must consider higher nominal dose to compensate the B loss.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of Contact Resistance with Molecular Ion Implantation

Basic characteristics of ClusterBoron (B{sub 18}H{sub 22}) implantation were investigated for improving contact resistance in DRAM devices. Generally, {sup 49}BF{sub 2} has been widely used for contact implant application in DRAM manufacturing because of its higher productivity compared to monomer boron ({sup 11}B). However, because of limited activation in a low thermal budget ({approx}800 deg. C) anneal, the sheet resistance was saturated for doses over 5x10{sup 15} ions/cm{sup 2}. Although many investigations have been reported, such as {sup 30}BF implant mixed implant with monomer boron etc., no practical solution has been found for dramatic improvement of contact resistance in a productive manner. B{sub 18}H{sub 22} was developed to overcome the productivity limitations encountered in low energy, high dose boron implantation and the limited activation of {sup 49}BF{sub 2} due to co-implanted fluorine. In this study, basic characterization of the B{sub 18}H{sub 22} contact implant was performed through sheet resistance, SIMS (Secondary Ion Mass Spectrometry) and XTEM (cross-sectional transmission electron microscopy). The B{sub 18}H{sub 22} implants showed lower sheet resistance than conventional {sup 49}BF{sub 2} for 5x10{sup 15} ions/cm{sup 2} on bare wafer tests. Through XTEM study, we found the activation behavior of both B{sub 18}H{sub 22} and {sup 49}BF{sub 2} were directly related with the amorphous layer thickness and residual defects from low thermal budget anneal. PMOS contact resistance in the sub-70 nm device by B{sub 18}H{sub 22} implantation showed considerable improvement (about 30%), showing B{sub 18}H{sub 22} could replace the BF{sub 2} for contact implant in contact resistance implant.

36 MATERIALS SCIENCE↗

Ultra-Shallow P{sup +}/N Junction Formation in Si Using Low Temperature Solid Phase Epitaxy Assisted with Laser Activation

A combination of Ge pre-amorphization implantation (Ge-PAI), low-energy B implantation and laser annealing is a promising method to form highly-activated, abrupt and ultra-shallow junctions (USJ). In our previous report of IIT 2006, we succeeded in forming pn junctions less than 10 nm using non-melt double-pulsed green laser. However, a large leakage current under reverse bias was observed consequently due to residual defects in the implanted layer. In this study, a method to form USJ is proposed: a combination of low-temperature solid phase epitaxy and non-melt laser irradiation for B activation. Ge pre-amorphization implantation was performed at energy of 6 keV with a dose of 3x10{sup 14}/cm{sup 2}. Then B implantation was performed at energy of 0.2 keV with a dose of 1.2x10{sup 15}/cm{sup 2}. Samples were annealed at 400 deg. C for 10 h in nitrogen atmosphere. Subsequently, non-melt laser irradiation was performed at energy of 690 mJ/cm{sup 2} and pulse duration of 100 ns with intervals of 300 ns. As a result, USJ around 10 nm with better crystallinity was successfully formed. And the leakage current of pn diodes was reduced significantly. Moreover, it is proven from secondary ion mass spectroscopy (SIMS) analysis that transient enhanced diffusion (TED) of B is specifically suppressed.

36 MATERIALS SCIENCE↗

The Effect of Amorphization Conditions on the Measured Activation of Source Drain Extension Implants

Un-patterned wafers were processed using low-dose Indium or medium-dose Germanium pre-amorphization implants (PAI) followed by p-type dopant implants of BF{sub 2} or carborane (CBH). The wafers were then annealed by RTA (spike), laser anneal (LSA) or combination of LSA and spike. Active dopant distributions calculated from SIMS and sheet resistance measurements compared favorably with those determined by differential Hall, which is a challenging technique for shallow profiles. The trends in B diffusion behavior and activation are discussed in relation to the different implant damage budgets, damage evolution during the anneals and presence of fluorine. In particular, for low thermal budget LSA only anneals, CBH implants appear to give higher activation than BF{sub 2} due to the absence of fluorine.

36 MATERIALS SCIENCE↗

XPS and AFM Study of GaAs Surface Treatment

Obtaining smooth and atomically clean surfaces is an important step in the preparation of a surface for device manufacturing. In this work different processes are evaluated for cleaning a GaAs surface. A good surface cleaning treatment is that which provides a high level of uniformity and controllability of the surface. Different techniques are useful as cleaning treatments depending on the growth process to be used. The goal is to remove the oxygen and carbon contaminants and then form a thin oxide film to protect the surface, which is easy to remove later with thermal desorption mechanism like molecular beam epitaxy (MBE) with minimal impact to the surface. In this study, atomic force microscopy (AFM), x-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS) were used to characterize the structure of the surface, the composition, as well as detect oxygen and carbon contaminant on the GaAs surface. This study consists in two parts. The first part the surface was subjected to different chemical treatments. The chemical solutions were: (a)H{sub 2}SO{sub 4}:H{sub 2}O{sub 2}:H{sub 2}O(4:1:100), (b) HCl: H{sub 2}O(1:3), (c)NH{sub 4}OH 29%. The treatments (a) and (b) reduced the oxygen on the surface. Treatment (c) reduces carbon contamination. In the second part we made MOS devices on the surfaces treated. They were characterized by CV and IV electrical measurements. They show frequency dispersion.

36 MATERIALS SCIENCE↗

CTA simulations with CORSIKA/sim lowbar telarray

While current atmospheric Cherenkov installations consist of only a few telescopes each, future installations will be far more complex. Monte Carlo simulations have become an essential tool for the design and optimisation of such installations. The CORSIKA air-shower simulation code and the sim lowbar telarray code for simulation of arrays of Cherenkov telescopes have been used to simulate several candidate configurations of the future Cherenkov Telescope Array (CTA) in detail. Together with other detailed and simplified simulations the resulting data provide the basis for the ongoing optimisation of CTA over a wide energy range. In this paper, the simulation methods are outlined and preliminary results on a number of configurations are presented. It is demonstrated that the initial goals of the CTA project can be achieved with available technology, at least in the medium and high energy range (about 100 GeV to 100 TeV)

79 ASTRONOMY AND ASTROPHYSICS↗

Ion yields and erosion rates for Si{sub 1-x}Ge{sub x}(0<=x<=1) ultralow energy O{sub 2}{sup +} secondary ion mass spectrometry in the energy range of 0.25-1 keV

We report the SIMS parameters required for the quantitative analysis of Si{sub 1-x}Ge{sub x} across the range of 0<=x<=1 when using low energy O{sub 2}{sup +} primary ions at normal incidence. These include the silicon and germanium secondary ion yield [i.e., the measured ion signal (ions/s)] and erosion rate [i.e., the speed at which the material sputters (nm/min)] as a function of x. We show that the ratio R{sub x} of erosion rates, Si{sub 1-x}Ge{sub x}/Si, at a given x is almost independent of beam energy, implying that the properties of the altered layer are dominated by the interaction of oxygen with silicon. R{sub x} shows an exponential dependence on x. Unsurprisingly, the silicon and germanium secondary ion yields are found to depart somewhat from proportionality to (1-x) and x, respectively, although an approximate linear relationship could be used for quantification across around 30% of the range of x (i.e., a reference material containing Ge fraction x would give reasonably accurate quantification across the range of +-0.15x). Direct comparison of the useful (ion) yields [i.e., the ratio of ion yield to the total number of atoms sputtered for a particular species (ions/atom)] and the sputter yields [i.e., the total number of atoms sputtered per incident primary ion (atoms/ions)] reveals a moderate matrix effect where the former decrease monotonically with increasing x except at the lowest beam energy investigated (250 eV). Here, the useful yield of Ge is found to be invariant with x. At 250 eV, the germanium ion and sputter yields are proportional to x for all x.

36 MATERIALS SCIENCE↗

The effect of oxygen during irradiation of silicon with low energy Cs{sup +} ions

The effect of oxygen flooding during ultralow energy SIMS depth profiling of silicon with Cs{sup +} primary ions is presented. New experimental data show the effective sputtering yield of silicon in the presence of oxygen, as well as the energy distribution of the secondary Si{sup -} ions. It is found that the component sputtering yield of Si is very sensitive to minute amounts of oxygen in the proximity of the sputtered surface. At these very low flooding pressures (in the 10{sup -9}-10{sup -8} mbar range), one cannot account for a full oxidation in the time frame of a typical measurement; it is concluded that in this particular case, which is technologically very relevant, small traces of oxygen will change the desorption characteristics of cesium as well as silicon. It shows that oxygen that is adsorbed to the silicon surface provides an attachment site for impinging cesium ions and thereby increases the retention capacity of cesium tremendously. Also, oxygen changes the secondary ion yield and can even promote the desorption of Si from the analysis surface.

36 MATERIALS SCIENCE↗

Real Clifford Algebra Cl{sub n,0}, n = 2, 3(mod 4) Wavelet Transform

We show how for n = 2, 3(mod 4) continuous Clifford (geometric) algebra (GA)Cl{sub n}-valued admissible wavelets can be constructed using the similitude group SIM(n). We strictly aim for real geometric interpretation, and replace the imaginary unit i is an element of C therefore with a GA blade squaring to -1. Consequences due to non-commutativity arise. We express the admissibility condition in terms of a Cl{sub n} Clifford Fourier Transform and then derive a set of important properties such as dilation, translation and rotation covariance, a reproducing kernel, and show how to invert the Clifford wavelet transform. As an example, we introduce Clifford Gabor wavelets. We further invent a generalized Clifford wavelet uncertainty principle.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Improved interfacial state density in Al{sub 2}O{sub 3}/GaAs interfaces using metal-organic chemical vapor deposition

In situ deposition of Al{sub 2}O{sub 3} on GaAs was performed by chemical-vapor-deposition (CVD) with trimethyaluminum and isopropanol as precursors. A gallium-rich region in the Al{sub 2}O{sub 3} thin film above the interface was spontaneously formed via the in situ CVD process. Ga-enrichment of the interface was observed using secondary ion mass spectrometry (SIMS) depth profile measurement. X-ray photoelectron spectroscopy (XPS) results show that the gallium-rich region consists of Al{sub 2}O{sub 3} and Ga{sub 2}O{sub 3}, but no As{sub 2}O{sub 3} was observed. The Ga{sub 2}O{sub 3}-Al{sub 2}O{sub 3} layer above the oxide/GaAs interface reduces the frequency dispersion as measured with capacitance-voltage (C-V) characteristics and lowers the interfacial state density as compared to atomic-layer-deposition *(ALD) deposited films which do not display this gallium enrichment above the interface.

36 MATERIALS SCIENCE↗

Synchronized monochromator and insertion device energy scans at SLS

Synchronous monochromator and insertion device energy scans were implemented at the Surfaces/Interfaces:Microscopy (SIM) beamline in order to provide the users fast X-ray magnetic dichroism studies (XMCD). A simple software control scheme is proposed based on a fast monochromator run-time energy readback which quickly updates the insertion device requested energy during an on-the-fly X-ray absorption scan (XAS). In this scheme the Plain Grating Monochromator (PGM) motion control, being much slower compared with the insertion device (APPLE-II type undulator), acts as a 'master' controlling the undulator 'slave' energy position. This master-slave software implementation exploits EPICS distributed device control over computer network and allows for a quasi-synchronous motion control combined with data acquisition needed for the XAS or XMCD experiment.

43 PARTICLE ACCELERATORS↗

Impurities removal by laser blow-off from in-vacuum optical surfaces on RFX-mod experiment

An in situ window cleaning system by laser blow-off through optical fiber has been developed on the basis of a feasibility study previously presented. The beam generated by a Q-switched Nd:YAG laser is launched in a vacuum box into a high damage threshold optical fiber through a lens. The fiber output is focused on the impurities-coated surface of a vacuum window exposed to the plasma of the RFX-mod experiment, and it is remotely controlled with an xy motion system to scan the entire surface. We first investigate the energy density threshold necessary to ablate the deposited impurity substrate on removed dirty windows: above threshold, a single laser pulse recovers {approx}95% of the window transmission before its exposure to the plasma, while below it the efficiency of the cleaning process is too poor. The system so conceived was then used to clean the three collection windows of the Main Thomson scattering diagnostic on RFX-mod. We also present results obtained applying the same technique to the SiO-protected Al mirror used for the Z{sub eff} diagnostic: an energy threshold for efficient impurity removal without mirror damage is first identified, then ablation tests are executed and analyzed in terms of recovered reflectivity. The SIMS technique is used both with windows and mirror to study the composition of surfaces before and after the ablation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Relationship of deep defects to oxygen and hydrogen content in nanocrystalline silicon photovoltaic materials

We report measurements of the structural and compositional properties of a range of hydrogenated nanocrystalline films. We employed Raman spectroscopy for crystallinity and time-of-flight secondary ion mass spectroscopy (TOF-SIMS) for impurity characterizations. The crystalline volume fractions and impurity levels are correlated with the deep state densities determined by drive level capacitance profiling. Those defects were found to have a thermal emission energy of 0.65{+-}.05 eV. We found that the overall crystallinity correlated reasonably well with the density of such defect states and also found a strong correlation between the defect density and the levels of oxygen impurities. Possible origins of these defects are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of surface damage on organic materials irradiated with Ar cluster ion beam

The sputtering yields of organic materials under large cluster ion bombardment are much higher than those under conventional monomer ion bombardment. The sputtering rate of arginine remains constant with fluence for an Ar cluster ion beam, but decreases with fluence for Ar monomer. Additionally, because Ar cluster etching induces little damage, Ar cluster ion can be used to achieve molecular depth profiling of organic materials. In this study, we evaluated the damage to poly methyl methacrylate (PMMA) and arginine samples irradiated with Ar atomic and Ar cluster ion beams. Arginine samples were analyzed by secondary ion mass spectrometry (SIMS) and PMMA samples were analyzed by X-ray photoelectron spectroscopy (XPS). The chemical structure of organic materials remained unchanged after Ar cluster irradiation, but was seriously damaged. These results indicated that bombardment with Ar cluster ions induced less surface damage than bombardment with Ar atomic ion. The damage layer thickness with 5 keV Ar cluster ion bombardment was less than 1 nm.

36 MATERIALS SCIENCE↗

Ribbon and Spot Beam Process Performance of the Dual Mode iPulsar High Current Ion Implanter

Low energy implant process data are presented from a dual mode high current ion implanter. The iPulsar is a flexible single wafer implanter capable of running both ribbon beams with one-dimensional mechanical scan of the wafer and spot beams with two-dimensional wafer scan. The main components of the implanter are described and their operation explained. Boron concentration profiles in Ge pre-amorphized substrates, measured by secondary ion mass spectroscopy (SIMS) are presented before and after anneal with drift and decelerated beams. In addition, spot and ribbon beam as-implanted phosphorus and carbon profiles are presented and the characteristics of each mode of operation are discussed.

36 MATERIALS SCIENCE↗

True Zero Degree Incident Implants on VIISta3000

The deliberate use of channeling to control depth profiles has come of age in the application to CMOS imaging sensor device manufacturing. In order to enable the true zero implant application on VIISta3000, we have optimized beam incidence angle control, using beam optics models and experimental measurements. The experiment measurement and the beam optics analysis results agree, showing a variation of less than 0.03 deg. (1{sigma}) across the wafer and from wafer to wafer. Achieving this accuracy in a manufacturing environment requires careful calibration and tight control of the collimator magnet and the mechanical scan system. In this paper we discuss the root cause of beam incidence angle variation on VIISta3000 and explain the calibration and optimization used to insure the consistent minimized beam incidence angle. We show experimental data, including ThermaWave and SIMS profiles.

43 PARTICLE ACCELERATORS↗